TX2000 USB Ports, Digitizer and Webcam not working (several people have save problem)

OK folks this is an old problem that was posted on the old TX/TM board:
http://h30434.www3.hp.com/t5/TX-TM-Series-Notebooks-Reply/tx2000-usb-ports-digitizer-webcam-all-not-...
Several of us have had these ports/hardware fail.
****IT IS NOT A BLACK SCREEN FAILURE******
In my case, the motherboard has very low hours after replacement, full system reinstall, all drivers up to date. If you take the time to read all three pages, you will see that many of us have tried everything that anyone suggested. Most of us still believe that this is a software issue as opposed to a hardware issue.
Not much hope for a soulution, but thought I would try this board since the TX/TM board is now reply only and probably has a very low visit rate.
Jim

I also am not able to use the pen and touch features after doing a recovery manager to factory spec, everything else is good but like the others when trying to open Tablet Properties it gives the message a supported tablet was not found on the system, also after updating the digitizer from hp the version does not change it's still 6.1.6002.18005 when it's supposed to be 5.05-5_HP5 Rev.A.
I've unblocked the download in properties ran it as administrator,uninstalled the old driver, my USB works my Quick launch buttons work, the screen rotates, the bios is updated. ran HP Update it finds two updates -a HP update software utility and a critical update HP Photosmart and then nothing else when there are many many more at the software and driver page for the TX2000
Is HP being silent due to the class action lawsuit? Was that a perk that hp got for settling, that they no longer have to address any issue with this Tx2000 series?
As so many have wrote before...... NEVER AGAIN HP!

Similar Messages

Signed up twice for adobe pdf export to word and still not working - anyone else have this problem?

signed up twice for adobe pdf export to word and still not working - anyone else have this problem?

In XI.
I can’t just export to word as I have done in the past in one simple click.
Convert to button is greyed out.
Now I have to save the pdf file on c drive when I am in outlook…then goto export pdf file…then find file then export to word.
I bought new computer with windows 8 (which is awful) and then bought pdf export again…
Any thoughts on how I can get back to one simple click again when I open a pdf file from an email in outlook?
Thank you,
Mike

Microphone and Webcam not working/Webcam not recognized by YouCam

Hello,
I have a dv7-6c95dx and my YouCam program tells me that it does not recognize my integrated webcam. I have read all of the webcam forums on this site and clicked on all of the links people have posted in the forums. I have uninstalled the CyberLink YouCam program and it still comes up with the same messages. The webcam also does not show up in my device manager. The microphone is malfunction as well, it will not work any any programs including skype.
I have heard that the webcam can come unplugged internally, will that also cause the microphone to stop working? I have run out of options and I do not want to pay anyone to fix it. I would appreciate any advice on this subject.

Hi DillOrNoDill,
Thank you for visiting the HP Support Forums and Welcome. I have read your thread on your HP Pavilion dv7-6c95dx Notebook and sound and microphone issues and Webcam not working correctly. I would be happy to assist if needed. Try these steps first.
1. Right click speaker icon (right hand corner)
2. Select Playback devices
3. Right click Speakers
4. Enable it and set as Default
5. Click Apply/Ok
You could also try Microsoft troubleshooter located on your Notebook.
Here is a document on WebCam troubleshooting. The Webcam will be listed in your device manager under Imaging devices. You should be able to click the action button and scan for new hardware.
Hope this helps.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

My airport express has a blinking yellow light and is not working. I have tried resetting it a few times, to no avail. My airport utility on my desktop detects it and will attempt to connect. However, after a few moments it says "An unexp

My airport express has a blinking yellow light and is not working. I have tried resetting it a few times, to no avail.
My airport utility on my desktop detects it and will attempt to connect. However, after a few moments it says "An unexpected error occurred Try again."
I'm running Mavericks on a 24-inch 2007 mac, 2.4 GHz Intel Core 2 Duo, 4 GB 667 MHz DDR2 SDRAM, OS X 10.9.3 (13D65). The Airport Express is model A1264. I connect to it via an Airport Extreme with 7.6.4.
Thanks in advance.

I have the same problem with my airport express – a blinking yellow light and it is not working. I have tried resetting it a few times.
My airport utility detects it and try to connect. However, after a few moments it says "An unexpected error occurred Try again.
Airport Express is model A1143
And I have tried to connect with iPhone - same same.

•I have just bought a Toshiba external hard disk to back up all my work from my macbook and its not working! I have checked the hard disk

•I have just bought a Toshiba external hard disk to back up all my work from my macbook and its not working! I have checked the hard disk

its not working: (sorry for being so ambiguous), the computer recognises it, it comes up on my desktop, when i open it and try and drag a file across, it is unable to go into the drive, there is just a symbol indicating 'no' (i've read the instructions from Tosheba and there is no help). I have not partitioned the drive using the GUID partition scheme - i dont know what this means?!

Everytime i plug my iphone into my computer it says device not recognized i was syncing my phone and it got interupted and has not worked since i have iphone 4 with 4.1 software lol what can i do to not lose everything

Everytime i plug my iphone into my computer it says device not recognized i was syncing my phone and it got interupted and has not worked since i have iphone 4 with 4.1 software lol what can i do to not lose everything

I'd start with the following document with that one:
iPhone, iPad, iPod touch: How to restart the Apple Mobile Device Service (AMDS) on Windows

My phone doesn't ring when someone is calling, but the sound works otherwise, like the alarm etc. I have tried to fix it in settings but still not working. anyone else have this problem?

my phone doesn't ring when someone is calling, but the sound works otherwise, like the alarm etc. I have tried to fix it in settings but still not working. anyone else have this problem?

Thanks so much but none of that helped. It was driving me crazy because it would back up another external drive. I just changed the name of the drive from iPhoto/iTunes Library to Media Libraries and IT WORKED!! I guess for some reason it didn't like the drive being called iPhoto or iTunes ???? I don't understand but I have tried so many solutions and exchanging things out but the name change did it????!!!
Thank you for your help and replying to this. Guess I made my own issue!

Qosmio F60 - USB ports & touch keys are not working

Hi,
After a clean install (win 7 home prem), i found most of the drivers, but still have following problems.
1) when i hook up my external hdd or any device to any usb port, although it powers and tries to read, but does not show in my computer and does not work
2) the touch keys (eco, wireless, media buttons) dont work. After installing value added pack, it opens up a button assignment tool and asks me for input for button assignment
3) The reason for clean install was new 250gig SDD to replace my 750gb toshiba hdd. this is the 3rd time hdd has corrupted in 2 years (not happy), however, the ssd halts the laptop as well, and i have to restart
Your help is much appreciated.
[email protected]

Do you have the latest firmware on the SSD?
Have you installed all the drivers and software listed on the Toshiba website? Make sure you install the Intel Chipset utility first, then TVAP second.
Also make sure you have Win7 Service Pack 1 before installing drivers, and update the BIOS to the latest revision.
If you still can't get it working, you can order the Recovery Discs from Toshiba and install the factory image on the SSD so everything works properly.

E3000 ports 2 and 3 not working

I have 4 computers hooked up(wired) to the E3000, i noticed that the ports 1 and 4 work(have internet and are lit) and ports 2 and 3 do not work at all. Cannot accuses routers page along with that. I did a clean install(factory settings/restarted) and tried the same ports, they still do not work. I looked at the routers settings, the ports are not blocked, is this a defective item?

First press and hold the reset button on the router for 45 - 60 seconds and then reconfigure the router from scratch. Now the ports should work and even after re-configuring the router, If the port number 2 and 3 is not working then it's a hardware fault.

DV9910US Audio and webcam not working.

Hello, I have worked for over a month on trying to restore a HP DV9910us. I even ordered the recovery CD from HP. I can not get the audio working or the webcam working. I have done extensive research online and tried every solution I found. Any help will be appreciated. Thanks

Hello robc1042. I understand you're having some issues getting your audio and webcam to work.
You said that you've tried numerous solutions. Would you mind giving a quick list of the sorts of solutions you have tried? This will be helpful as I wouldn't want to suggest solutions you've already attempted.
You may even want to take a look at this thread. I posted this a little while back but it covers the solutions for a webcam not being detected. You may find it helpful.
To begin I would like to see if either the webcam or sound card is listed in Device Manager. Try the following.
Click Start, type "Device Manager," and press Enter.
Expand the "Imaging Devices," "Sound, video, and game controllers," and "Other Devices" sections.
List what you see.
I will await your reply. I hope you have a great day!
Please click the white star under my name to give me Kudos as a way to say "Thanks!"
Click the "Accept as Solution" button if I resolve your issue.

No audo, usb not working, memory card not working and webcam not working

my audio, usb ports, webcam, and memory card reader stopped working all of a sudden about 3-4 weeks ago i tired restoring it to factory settings nothing helped. need my laptop to work for school i need to use all these device for a class i am taking!
these are specs for the laptop
»HP G62t-350 CTO Notebook PC
Serial Number: {Removed for privacy}
Product Number: wv689av
have a 64 bit

Hi:
The touchpad driver from your notebook's support and driver page is sp69626...
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-145252-1&cc=us&dlc=en&lc=en...
The PCI Device (card reader) needs this driver...
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-141812-1&cc=us&dlc=en&lc=en...
Download and install the amd chipset drivers and reboot for the usb 3...
http://support.amd.com/en-us/download/chipset?os=Windows%207%20-%2064

USB devices and Webcam not working or installing on Pavilion Laptop

Hi there,
I have a HP Pavilion Dm3 1030 sa,
For a while now certain USB devices have just not worked on the laptop, specifically printers and mice, despite me reinstalling the drivers for those devices on the laptop. I tried the devices on other computers and they worked fine.
This was annoying but I put up with it.
Now the webcam and microphone have stopped working and are no longer recognised by the computer. I have reinstalled the webcam software but cannot find the drivers for it. The software (arc soft webcam) says the inbuilt webcam is not connected.
I have been able to get my iphone to connect via usb and usb drives work most of the time. I don't really know what is going on. When I look at devices that don't work in device manager It says that there is a USB I/O error. I have tried reinstalling the drivers using device manager but that didn't work either. Any advice would be appreciated. Not being able to use a mouse is annoying as track pads are slow.
Pn vj409ea#ABU
Is my notebook in the warranty period? No (three months out)
Is the originally installed OS still installed (Yes)
Have I changed the partitions (NO)
Thanks for any help
Kieran Latham

run an extended _*Apple Hardware Test*_.
JGG

Need help one USB Port on MacBook Pro not working

Its been a weak now and im getting tired of my MacBook pro USB not reading anything.. It wont read/connect usb drives, IPods/IPhones/IPads, and Android phones. I have tried the PRAM and SMC resets and nothing has worked i even left my Macbook pro off for a whole day. ITS ONLY ONE PORT NOT WORKING, i took it to bestbuy because its closest to me but geek squad just did what i explained above and told me get a USB hub and NO! i want to fix this issue... Anyone has had this happen can you let me know if its because the USB port is no longer working or a software issue... Also i keep getting this notification telling me USB devices disabled draining to much power but i have nothing connected!!
ps- my MacBook Pro is getting very hot fast and it happens when im not even using it, i get home and it very hot could there be another hardware failure i dont leave applications open when i sleep it.

It sounds like you might have a hardware problem. Your best bet is to go to the Genius Bar. The evaluation is free, and they'll fix it if you're under Applecare. Back up your stuff first though.

USB ports on my iMac not working

I tried to connect a battery from something else through a USB port on my iMac and there was a prompt that "the device was drawing too much power and that the USB port will be shut down". I, being foolish enough,plugged it in the other USB port and the same thing happened and this time the computer automatically shut down. I turned it on and neither of the 2 USB ports (out of the total 4) have been working since then.
I tried shutting the the computer down and restarting after an hour but they're still not working. Does anyone know how to fix this!!!

Sounds like the port overload protection for those ports has tripped.
Reset the SMC > http://support.apple.com/kb/HT3964
1. Shut down the computer.
2. Unplug the computer's power cord.
3. Press and hold the power button for 5 seconds.
4. Release the power button.
5. Attach the computers power cable.
6. Press the power button to turn on the computer.
Then if that does not reset them, disconnect everything and let the iMac sit disconnected for 10 or 15 minutes.
Dennis

Sd card reader & USB port (right side only) not working

I recently purchased a Macbook Pro 15" retina display with OS Moutain Lion. The SD card reader and USB port on the right side of the computer do not work. I've restarted the computer numerous times, tried to reimage the computer with the Control+R during restart (didn't allow for update because Mountain Lion was loaded on the system), and downloaded with the latest updates but they still do not work. I am currently deployed to Afghanistan so Apple Support calling me back isn't going to work. Any help would be appreciated.

Hello :
TNX for your reply.
Unfortunately, I do not own a 2 gig mem card to test with. What perplexes me is that when I watch device manager and open properties boxes for the USB dev, SMSC-2228 dev, and the newly created disks, the Win XP drivers do indeed load, but watching it do so is sloooooooowwwwwww. Slow as in 3 - 5 minutes for the win drivers to load in place. Funny thing is, an xD mem card or Memory stick initialize, set up properly in a matter of at most 5 - 10 seconds or so. The only card type I have a problem with is THE MOST COMMON ONE, the SD card. Maybe a Micro/Mickey soft thing? Some info I found on the SMSC controller claims it supports the larger sd card sizes, so I think this is a Micro / Mickey soft thing. I guess I need to search for some better drivers somewhere.
TNX for now

TX2000 USB Ports, Digitizer and Webcam not working (several people have save problem)

Similar Messages

Maybe you are looking for