UC560 and SPA504 - functionality problems

Cisco SPA 500 IP Phones do not allow a transfer of calls coming from PSTN to another internal destination. Phones are registered to SPA 560 using SPCP protocol. Scenario: Incoming call from PSTN to DN 1000, transfered to 1001. When the transfer button on DN 1000 is pressed for the second time, the call is dropped. Transfer system full consult. MTP and transcoder available, however not used during this session at all. Connectivity to the PSTN is through SIP trunk with g711alow only.
The second problem: Czech localization on these phones is completely useless, since it displayes Czech special characters in wrong charset, resulting in total nonsence. Czech char set should be UTF-8. The customer demands right czech characters, as promissed by Cisco, optherwise, they are not going to accept the project at all.

Issue 1, would need to see SIP traces, etc.
Issue 2, Cisco is know to do bad localization, if they do it at all. You can contact them but I would not expect a real resolution.

Similar Messages

Nested Ago and Todate function problem

Hi,
in my rpd i have following Time hierarchy:
Year
Quarter
Month
and a fact table Fact Shop which contains Monthly measure "Number of Hearing Aids Delivered".
I must calculate PY_QTD, PY_YTD versions of above measure.
I have tried to use built-in Time Functions Ago and ToDate in the following way:
PY_QTD
Todate(Ago("Number of Hearing Aids Delivered",1,"Time.Year"), "Time.Quarter")
PY_YTD
Todate(Ago("Number of Hearing Aids Delivered",1,"Time.Year"), "Time.Year")
but when i check consistency i have error which says approximately "You can nest Ago and ToDate functions".
There's another way, to calculate it? Can you help?
Thanks
Giancarlo

So u r referring PY as previous year ;)
Here u go;
it’s a combination of AGO and TODATE.
You create a value – let’s say Sales MTD by just following normal process…then you create a logical column with the following formula AGO (Sales MTD, Month Dim, 12)
that should give you a MTD measure you’re looking for. I hope this is useful. Just dont use both function in single logical column....use seperate by first creating YTD n then AGO function to create previous year data.
For ur case use to calculate PY_YTD use below:
Create logical column
Aids Delivered YTD with formula as TODATE("Number of Hearing Aids Delivered"), "Time.Year")
and then create another logical column as
Aids Delivered PY_YTD with formula as AGO("Aids Delivered YTD","Time.Year",1)
This will work for sure....

Start up and basic function problems

My computer has been running abnormally slowly recently. For example, it will take about 30 seconds to start apps such as ichat, mail, or safari. Occasionally, my computer will just freeze and i won't be able to switch spaces, applications, windows or open the dock or force quit menu. Usually 30 seconds later it will do all of those functions at once. I also have applications such as ichat announce when buddies come online, but the delay is usually 5-10 seconds. Furthermore, when my clock hits the hour, my menu bar will reset and all items will disappear and all of my apps will freeze for about 15 seconds. Also, when I tried to install the latest apple updates and selected restart, my computer would not install anything. Instead, Finder quit but my computer did not shut down. I was staring at my background with no icons. My dock was hovering at the bottom of my screen and I could restart Finder from it, but when I tried to shut down again, my computer would not. It would simply quit finder then show an error saying that either software update or finder did not quit. I eventually forced a shut down and started back up, but the software update window came up with the same software that I just updated. I repaired permissions and the disk through disk utility, ran the maintenance scripts, and re-updated. This time, my computer would shut down, but would not start back up. I could tell that my disk was running because it got really hot, but the screen never started and the latch light on the front would glow, but i could not wake it. I forced a shut down and restarted, but it stalled at the grey/white screen and the apple logo never appeared. I forced shutdown again, and this time it booted up, but it took 5 minutes to get to the login screen.
Does anyone have any suggestions? Or, is my only option (as i had feared) to backup and reinstall (i didn't bring my install disk with me to school, so I'm going to need temporary fixes for now).
Thank you,
Hobbesocrates

I found someone with an install disk and ran Repair Disk. It said that the disk was ok. I also ran repair permissions and one of the lines was a warning and said: SUID file System/Library/Coreservices/Finder.app/Contents/Resources/OwnerGroupTool" has been modified and will not be repaired. After fixing all that I could with that, I restarted and my computer showed minor improvements, but is not functioning anywhere near the optimal speed it was a while ago.
However, I did download iDefrag and checked the defragmentation of the disk. Over 50% of the disk was fragmented. I'm thinking of burning a bootable cd and running idefrag demo or drive genius 2 demo off of that. would that be a good plan
thank you

Problem with tpcall and tpgetrply functions

Hi,
I have a problem with tpcall() and tpgetrply() functions.
In this example (invoke tpcall()):
FBFR32 *buf;
FLDLEN32 buflen;
buf = a_buffer.getBuffer(); /* getBuffer() returns FBFR32* */
buflen = a_buffer.getLongitud();
/* at this point: buf == a_buffer.getBuffer() */
if (tpcall(a_contenedor.getServname(),
(char*)a_contenedor.getBufferPeticion()->getBuffer(),
a_contenedor.getBufferPeticion()->getLongitud(),
(char**)&buf,
(long*)&buflen,
0) == -1)
if (tperrno != TPESVCFAIL)
LANZAR_EXCEPCION(CADENA_WHAT_SB,
"Error en funcion Execute(), llamada tpcall()",
tpstrerror(tperrno))
/* at this point: buf != a_buffer.getBuffer() */
tpcall() function change the memory address of buf. What is the problem? Is wrong my code? Is a problem with tuxedo version?
My tuxedo version is:
tmadmin -vINFO: BEA Tuxedo, Version 8.0, 32-bit, Patch Level 306
INFO: Serial #: 650522264137-773290431251, Expiration NONE, Maxusers 150
INFO: Licensed to: Telefonica Moviles Espa?a, S.A.
INFO: 56-bit Encryption Package
Thanks,
ANTONIO.

There's nothing wrong with your code or tuxedo. tpcall (and tpgetrply) can change the address of the return buffer if it needs to allocate more memory to hold the data. This is the reason why you pass a pointer to the buffer as the output buffer parameter to tpcall and tpreturn. Everything is working as expected.

Has anyone had a problem with TapMedia File Manage on iPhone 5. I reported a WIFI functionality problem to the developer and asked for support. Instead they have been very unprofessional by name calling me instead of logically evaluate and troubleshoot th

Has anyone had a problem with TapMedia File Manage installed on iPhone 5? I reported a WIFI functionality problem to the developer and asked for support. Instead the company has been very unprofessional by name calling me instead of logically evaluate and troubleshoot the problem

Hi AKE1919,
Welcome to the Support Communities!
The following information should help you with this:
How to report an issue with your iTunes Store, App Store, Mac App Store, or iBookstore purchase
http://support.apple.com/kb/HT1933?viewlocale=en_US
Cheers,
Judy

Im using xcode 4.6 and im having problems reading files using the fopen function in c

Im using xcode 4.6 and im having problems reading files using the fopen function in c

Yes, but that would not cause the "build failed" message.
right I missed that part. Looks like two problems then.
// main.m
// ASCTestFopen
// Created by Frank Caggiano on 3/2/13.
// Copyright (c) 2013 Frank Caggiano. All rights reserved.
#import <Foundation/Foundation.h>
#include <stdio.h>
int main(int argc, const char * argv[])
    @autoreleasepool {
        FILE *fp, *fopen();
        // insert code here...
        if((fp = fopen("~/test.txt","r")) == NULL)
            NSLog(@"open failed");
    return 0;
This will compile ad run in Xcode with a project type of comand line tool

Hey my iphone 4 has a problem regarding carrier. Its always showing searching mode and wifi-address N/A and Bluetooth address 00:00:00:00:00 and call function is disable

hey my iphone 4 has a problem regarding carrier. Its always showing searching mode and wifi-address N/A and Bluetooth address 00:00:00:00:00 and call function is disable. Please help me. I have tried every thing ..like restore from DFU mode with out sucess.

Refer to Note 98458 - SAPMSSY1, CALL_FUNCTION_NOT_FOUND

Preferences problem ... desktop and screensaver function missing

The desktop and screensaver function in my preferences has disappeared, not to be found at all on my computer. I saw this problem posted with the response to download Pacifist. I did that but cannot figure out how that would help, so I still have the problem. Any recommendations?

Have you tried repairing disk permissions for the screensaver issue?
Launch Disk Utility. Select MacintoshHD in the panel on the left, select the FirstAid tab. Click: Repair Disk Permissions. When it's finished from the Menu Bar, Quit Disk Utility and restart your Mac.
If that doesn't help... try the 10.5.7 combo update available here. http://support.apple.com/downloads/MacOS_X_10_5_7_ComboUpdate
Make sure and repair disk permissions after the installation.

Problems with Dock, Exposé and Mouse functions

First: Sorry for my bad english.
The function that the symbols in Dock are getting bigger and smaller by placing the mouse on them doesn´t work.
The functions in the corners (Exposé, dashboard,...) don´t work.
The same with my right mouseclick.
I can´t put something in my trash. I can grab a folders but not put in in the trash.
The same with my "Top Sites". They are show´n but i can´t use them.
There are different other little things wrong, but there must be a solution for all the stuff, cause everything has broken today.
Thanks for your support.

Hi
I have exactly the same problem :
- My dock don't react when i put my mouse on the right (dock stay hidden)
- When i let my dock on the right but I clic, the dock see my mouse and show
- After to clic on aplication, the dock animation stay locked until i clic again somewhere (dock hide)
- Exposé don't work when I move my mouse to each corner, when I use keyboard all is ok, but he just don't detect my mouse (like my dock).
I test some solutions :
- Creat new administrator acount (same problem)
- Try to reapared with the CD of Snow leopart (boot from CD)
- Use OnyX to clean all (same problem)
- Reboot (normal reboot)
- change settings of dock and exposé (same problem)
I don't want to format my computer, could you help me ?
Thanks
Message was edited by: Angeal Niagara

Applications installed in my iTouch does not launch. the music and internet functions but the installed applications does not. tried switching it on and off, still problem persists

Applications installed in my iTouch does not launch. the music and internet functions but the installed applications does not. tried switching it on and off, still problem persists. help...

Your only chance besides getting it serviced would be setting it up as new device:
http://support.apple.com/kb/HT4137

Power button and other functions on my Nokia N86 s...

After I downloaded a few applications for my Nokia N86, the slider preferences (i.e. the sound clips that play when opening/closing the slider; the answer/hang up call function; and the key lock) stopped working. Some apps refuse to open (no response). Also, when I push the power button on top of the phone, it does absolutely nothing, thus I cannot turn my phone off.
I am affraid to take the battery out and let the phone power down then up because the power button might not be able to turn it on.
This occurred after I downloaded a few apps off of cnet.com. Here is a list of my downloaded apps with the most recently downloaded ones listed first:
F-Secure (anti virus added and scanned after problem started - no viruses present)
Handywi (wifi locator)
fring (social networking bundle)
DivX player
Google app (m.google.com/app)
Google maps
Opera Mini (web browser that now refuses to open)
HNN Soft Talking Dictionary (Chinese/English that now refuses to open)
What should I do???
(Yes, I have the most current software update)
(Not sure if it matters, but I live and bought the phone in Taipei, Taiwan)
Message Edited by sk8erfrombham on 07-Jul-2009 02:22 PM
Solved!
Go to Solution.

Sorry, if you are not willing to try it then I cannot help you.
Take it to a nokia care point for assitance.
Care points/service centres and repair info:
UK • Europe • Asia-Pacific • USA •
Canada • Middle East and Africa
Elsewhere: Click here, select your country, go to the support section, then select repair.

Animated gif and page refresh problem

Animated gif and page refresh problem
Hi There,
I'm trying to build a simple "Please wait......" screen using jsp and javascript.
So far all is going well except that my animatate gif keeps refreshing everything the page is refresh.
Is there a way the i can prevent the body of the page from refreshing?
below is my sample code:
<%@taglib uri="http://java.sun.com/jsp/jstl/core" prefix="c"%>
<jsp:useBean id="StatusBean" class="com1.CandidateRelease" scope="session"/>
<html>
<script LANGUAGE="JavaScript">
function refresh()
<% if (StatusBean.isRunning()) { %>
     //setTimeout("refresh()", 1000);
     setTimeout("location='status.jsf'", 1000);
<% }else{%>
     window.location= "busStopAdmin.jsf";
<%} %>
</script>
<head>
     <script LANGUAGE="JavaScript">
          refresh();
     </script>
</head>
<body>
     <img id="myImage" src="../img/ojp_wait.gif" alt="" width="151" height="36">
</body>
</html>

Animated gif and page refresh problem
Hi There,
I'm trying to build a simple "Please wait......" screen using jsp and javascript.
So far all is going well except that my animatate gif keeps refreshing everything the page is refresh.
Is there a way the i can prevent the body of the page from refreshing?
below is my sample code:
<%@taglib uri="http://java.sun.com/jsp/jstl/core" prefix="c"%>
<jsp:useBean id="StatusBean" class="com1.CandidateRelease" scope="session"/>
<html>
<script LANGUAGE="JavaScript">
function refresh()
<% if (StatusBean.isRunning()) { %>
     //setTimeout("refresh()", 1000);
     setTimeout("location='status.jsf'", 1000);
<% }else{%>
     window.location= "busStopAdmin.jsf";
<%} %>
</script>
<head>
     <script LANGUAGE="JavaScript">
          refresh();
     </script>
</head>
<body>
     <img id="myImage" src="../img/ojp_wait.gif" alt="" width="151" height="36">
</body>
</html>

EXCISE AND COMMISION AGENT PROBLEM

HI GURUS,
Presently we implementing SAP R3 in 1 Textile industry, All the customization is been completed. But we are facing a problem related to excise calculation.
1.The system is showing the excise value in general Invoice (output type RD00) but it is not showing in Excise Invoice (Output Type J1IN)
2.Automatic posting is not happening after general Invoice (RD00).
3. We have scenario of commission agent. we have created a account group as Commission and Partner function CM for Commission and CI for commission receipt at header level of sales document. Also a condition type ZCMN as account key & ZCMU as accrual key. also maintained gl account for same. while creating the Sales order we assign CM as a partner function and No. of commission agent at header level . and value for condition ZCMN eg. 1%. We have also maintained seperate account assignment group 04 for Commission agent and 01 for Sundry Debetor (customer account).
After releasing for accounting the acount details appears as follows:
70 (customer No) 50000- Cr
1500233 Revenue account 50000 Dr
160064 Provision accout - 500- cr
124656 Brokarage account - 500 dr
the system is not determining the commission agent's account as it is determining for customer. Which we have already maintained in VKOA account assignment 01 for customer and 04 for commission agent as mentioned above.
Kindly go through these issues and revert back with possible suggestions at your earliest.

Hi,
Please go through the link below, hope this help.
http://www.sap-img.com/sap-sd/steps-to-create-commission-for-agent.htm

When I try to send a link to a page from Safari, I get a message saying that sending the message to the server failed. It places a copy in the outbox. All other email and safari functions work properly. Ipad 2 IOS 7.1

My Ipad2 works fine except when I try to email myself a link to a safari webpage. I get an error message saying that the message failed to connect to the server. It says that a copy of the message has been left in the outbox. I cannot get the message from the outbox. All other email and safari functions work as expected.
I have cleared data and cookies, powered down, and done a reset. Nothing seems to help.

Typing in additional text seems to get the job done. This seems to be a feature of the latest IOS update, I have never had the problem before the last update.
I use the box with the arrow just to the left of the URL block at the top of the page to send myself links to pages of interest. Adding the extra text seems like a pointless step, but it does work.
Thanks.

Iphoto 9.3 and Mountain Lion Problems : Cant access my library : rebuilding doesn't work just hangs for hours

My Macbook Pro running Snow Leopard, had hard drive failure so I had to borrow a friends similar machine to access my iPhoto library ( 523 GB) on a 1TB drive after editing the photos and after exporting one folder of images the program quit and then asked me to repair which I tried hung up at 99% and would not open the event thumbnails . I have tried everything even trying to transfer the particular event from that library to a new library using iphoto manager just so I can export my project and send but still no success as it is telling me that it is getting no info from the library, I changed permissions on the drive ..still no success . I restarted Iphoto and it took hours to show the images but all events thumnails said "0" and it shows all the event cover photos as a gray photo with a palm tree in it or something . I tried rebuilding again this morning and the new library says "0" photos and a library size of 7.3 mb
I got my own Macbook 17in back yesterday and downloaded Mountain Lion to my machine and Iphoto 9.3
I tried to open the library which is 523 GB of images that used to work fine before getting an error message saying it needed to be repaired. I tried opening it with Iphoto 9.3 via I photo manager which told be that there were inconsistencies in the library and it needed to be repaired I chose that option and it is now the following day still "rebuilding thumbnails" since last night . This is a huge problem I have missed project deadlines and my income is severely affected by this situation of not being able to access my work. What can I do to fix this, access my files and export my overdue project at this point ?

Terence I find it surprising that you would say use Iphoto Manager after saying that I used it to rebuild using it took me to 99% of the way and just hung. I even spent my $20 and got the latest version 3.8.3 which was supposed to remedy these issues. See below my email to Fat Cat software the makers of Iphoto Manager:
"Email to Fat Cat Software : Re Iphoto problems:
My Macbook Pro running Snow Leopard, had hard drive failure so I had to borrow a friends similar machine to access my iPhoto library ( 523 GB) on a 1TB drive
after editing the photos and after exporting one folder of images the program quit and the asked me to repair which i tried …it hung up at 99% and would not open the event thumbnails .I have tried everything trying to transfer the particular event from the library to a new library using Iphoto Manager just so I can work on my project but still no success as IPLM is telling me that it is getting no info from the library, I changed permissions on the drive ..still no success .
I opened it using IPLM and it took hours to show the images but all events said "0" and it shows all the event cover photos as a gray photo with a palm tree in it or something . I tried rebuilding again this morning and the new library says "0" photos and a library size of 7.3 mb . There
really seems to be a serious problem with Iphoto 9.3 as it
asks you to rebuild or repair the library then IPLM stops at 99% leaving
the thumbnails
unviewable and just hangs up after that or wont open and there the problems start.
Please advise and give me some viable options on this issue."
Its days later and the support at Fat Cat software emailed me asking a question and are apparently just as floored as I am with this malfunction ..I hope they are working feverishly to address this as my conclusion and solution is as follows :
Using the older version of Iphoto Library Manager when my machine asked me to upgrade and rebuild instead of the first aid function in Iphoto 9.3 did not help but actually corrupted my library and downloading the latest version did not help remedy it either. What I should have done and am now doing is using the Iphoto first Aid function in Mountain Lion and Iphoto 9.3 using option command to rebuild the entire library. So far it is working with no hangups ...it is now rebuilding image version number 6715 and counting with 33000+ images to go ..if this solution really rebuilds then that is the ONLY way to go with this issue which has cost me a lot of time and money in missed deadlines , lost income and lost business . Iphoto and Iphoto Library manager are normally great in what their purposes are and in ease of use and function but whenawry with compatibility in version software issues arise things go terribly awry and the tedious painstaking fixes available that go for days on end just do not cut it.

UC560 and SPA504 - functionality problems

Similar Messages

Maybe you are looking for