UC560 - CUE can not reach internet

Hello all, new here, but not new to using Cisco equipment.  I am however new to the phone side of Cisco.
I'm currently working on an issue with my CUE traffic not routing out to the internet, however I'm feeling rather stumped at the moment and was hoping to get some insight from the community.
As a bit of background - on my UC560 the CUE IP is not the default, I had to change it due to an IP conflict (that was a painful process).  If I have a terminal open to the UC560, I can ping the CUE, and ping out to the internet.  If I open the session to the CUE, I am able to ping the UC560, however unable to ping an internet IP (i.e. 8.8.8.8).
Here are the results of a sh ip route:
S*    0.0.0.0/0 [1/0] via 10.1.0.1
      10.0.0.0/8 is variably subnetted, 7 subnets, 3 masks
C        10.1.0.0/24 is directly connected, Vlan1
L        10.1.0.228/32 is directly connected, Vlan1
C        10.1.1.0/24 is directly connected, Vlan100
L        10.1.1.1/32 is directly connected, Vlan100
C        10.10.10.0/30 is directly connected, Vlan90
S        10.10.10.1/32 is directly connected, Vlan90
L        10.10.10.2/32 is directly connected, Vlan90
I will be happy to share more configuration items as requested.  Any help would be greatly appreciated.
As an additional note, I would need the Vlan90 (CUE) traffic routed (Or maybe NAT'd) through the UC560, as I can not make any changes to the current router.
Thank you in advance!

The existing LAN is on the 10.1.0.0 Network.  When I session into the CUE, I can ping 10.1.0.228 (The LAN IP of the UC560), but I can not ping 10.1.0.1 (LAN Router - which I can not adjust routes) or any other LAN hosts.
Is there a way I can setup a route for the 10.10.10.0 through the LAN interface (10.1.0.228) of the UC560?  Or a way to NAT the 10.10.10.0 traffic behind that interface?

Similar Messages

  • Can not reach internet from vlan on 3560 switch but can from switch

    ISP provided me IP (207.70.170.42) and gateway address(207.70.170.41) connecting to  their router( meto E).
    I can ping outside the network when logged into the switch  through telnet but not when connected through a pc on the vlan.
    I can ping the IP address on port GI0/1  207.70.170.42 from the PC on vlan 99 (192.168.20.3).
    What do I need to configure to get the VLAN to send traffic to the internet.
    Tried ip route 0.0.0.0 0.0.0.0 207.70.170.41 
    Tried ip route 192.168.20.0 255.255.255.0 207.70.170.41
    Tried ip route 192.168.10.0 255.255.255.0 207.70.170.41

    Hi @rbrewer02,
    Are you doing NAT or PAT for private IP addresses? Remember that the ISP just see the public IP address that it gives to you (207.70.170.42 in your case).
    You should configure NAT so that your private IP ranges get translated into your public IP address.
    If you need help in configuring NAT just tell me.
    Rgrds,
    Martin, IT Specialist

  • Users of Windows 7 Computers connected to Domain but can not get Internet Randomly

    After crash of DC, I have replaced the domain controller server 2008 with another machine but with same name. I got trust relationship issue, which I resolved by disjoining and rejoining. After this I am facing below mentioned issue on computers randomly.
    High Privileges users have no issue with internet access. Low privileges users can not access internet on workstations randomly. Users login properly, all group policy settings applied to them. but internet does not work with them using Internet Explorer
    and Google Chrome. All pings work fine. I viewed the proxy settings by command line as proxy settings are disabled for low privileges users. It was correct but still internet was not working. While over Firefox by adding manually proxy(not set
    through group policy), internet works.
    When I tried to login through a new user which has not logged in over affected machine. Internet works. After logging off by new user and logging on old users (already created profiles), internet starts working for them too. I am afraid may this trick does
    not work on other machines.
    Now I want to know, if above mentioned trick does not work what should I do to activate the internet. What is the root cause of this issue.

    Hi,
    Did you mean you set the same proxy, high privileges user could keep connection and low privileges user drop connection randomly? At the same time, Firefox also could keep connection, right?
    Please try to reset Winsock and DNS for a test on problematic computer. Open command prompt with Administrator Previleges, then type the following commands.
    netsh int reset  
    ipconfig /flushdns   
    Besides that, update the network driver for test.
    Karen Hu
    TechNet Community Support

  • Can someone please help me figure out why I keep getting the "can not reach server" when I try to download the ebook? This is happening with Adobe Digital Editions.

    When I try to download the ebook I bough, the Adobe Digital Reader shows the following message: "can not reach server".  Can someone please help me with this?
    TO be precise, it says "licensee server communication problem"
    Thank you

    The thread running through your explanation has to do with connectivity to your server. (iCloud out of the blue asking for password, unable to message your boyfriend, unable to access e-mail). You said that you boyfriend restart his device and then the two of you were able to then imessage. My best advice for you would be to go to settings to reset to reset network settings. Once this has been done you then will need to enter the name and password of your wifi. ONce this is done you then can attempt to check to see that all passwords are enter correctly.
    Good luck.

  • IPhone 5s can connect to wireless WIFI router but can not access internet.

    iPhone 5s can connect to wireless WIFI router but can not access internet at work. The admin says the router lets my iPhone connect to LAN, but the iPhone does not have server IP to access the internet. I entered the server IP and port number in the HTTP PROXY fields but I still can not access the web. Any ideas?
    TIA
    Rich

    You IT person should be able to sort this out.  But, they seems to be too busy or disinterested to do this.  Suggest you provide the it person with an iPhone to get interested.
    Any could be lots of things.
    The best you can do is to get access to the admin setup for networking on a pc?  The internet settings are all the same.  Only what names the manufactures change from OS to OS. Check and compare parameters.
    Phone works to internet at home, I assume?

  • I can not reach to my accounts on computer since it says that 'connection server to .... is timed out'.

    I can not reach to my accounts on computer since it says that 'connection server to .... is timed out'. However, I can get my emails through my iphone. How can I make my accounts work on computer? This problem occurs occasionally but create a big problem for my works...

    If the iPads are Counterfeit then Apple will have nothing to do with them except maybe try to find the Counterfeiters and charge them.
    It's the usual story...  If something is too good or cheap to be true it probably is.

  • After downloading Yosemite, my Ps CS4 doesn't work. It says install legacy Java SE 6, but when i go ok, or, more info can not reach any point to have it!!!

    After downloading Yosemite, my Ps CS4 doesn't work. It says install legacy Java SE 6, but when i go ok, or, more info can not reach any point to have it!!! What will I do?

    I have similar issues and was referred to a knowledge base article support.apple.com/kb/DL1572  This seems to corrected the issue.

  • I can not reach the screen to enter passcode, the main sreen is where im stuck, i cant play music, the home button works but icant get pass the whole unlock thing, i can receive calls but can answer because when i touch the screen it wont do.

    i can not reach the screen to enter passcorde, the main screen is where im stuk, i cant play music,i can recive calls

    Try to Reset your device. 
    Press and hold both the Sleep/Wake button and the Home button for at least ten seconds, until the Apple logo appears (ignore the Slide to Power Off that shows up first).

  • HT3986 After installed win7 on my mac pro(mid 2012/mountain lion), I can not connect internet and where can i find drivers in mountain lion system

    After installed win7 on my mac pro(mid 2012/mountain lion), I can not connect internet and where can i find drivers in mountain lion system.
    I donot think I have a install disk when I bought my mac, there is only a disc partition for recovery system.

    Welcome to the Apple Support Communities
    You have to install Boot Camp drivers. On Mountain Lion, you have to download them.
    First, press X key while your Mac is starting to start into OS X. Then, open Boot Camp Assistant and select the option to download the drivers. You will have to burn them into a DVD or USB drive, so after downloading them, restart and install them into Windows

  • I can not reach my gmail account

    i can not reach my gmail account nor my hotmail account
    moreover ican not use my keyboard short cuts now though it worked well initially
    regards
    nawabdera

    Contact Google.

  • Can not access internet via wired connection, wireless working OK

    Background information,Came home from vacation turned on PC to access email.Emails started downloading then stoped,started getting messages that firefox stopped working and Thunderbird quit working and others.My desktop is attached to a verizon router.all my other devices are wireless and are working fine through the same router.I connected my laptop to the lan connection, turned off wifi and accessed the internet via lan connection.Using device manager, checked drivers, says up to date, also says that it is working properly.I have gone to the command line and can ping google.com.I can ping the loop around. ping127.0.0.1I have done the ipconfig/release,ipconfig/renew, and ipconfig/flushdnsipconfig/all indcates that it is there and enabledMy Lan connection is part of the mother board.can not access internet via wiredconnection.Not sure what to do next.Help Please   

    Reply: I spent about an hour last night doing all the things that you suggested including moving the lan cable from my desktop to my laptop which worked fine. When I hoover over the connection it says;  Network3                                                                                        Internet Access   no error messages.When I unplug the cable at the router a red x covers that connection icon.Plug it back in red x goes away.It is seeing the router, just does not appear to be providing selected web page info.Computer thinks it is working fine.

  • VLAN 2 can not reach the internet.

    I have two VLANs 2 and 3, VLAN 3 is my user network and VLAN 2 is my server network. The two VLANs can talk, but VLAN 2 can not get out to the internet. What am I doing wrong?
    Building configuration...
    Current configuration : 2735 bytes
    ! Last configuration change at 02:42:02 UTC Thu Mar 4 1993
    version 15.0
    service config
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname oacSwitch1
    boot-start-marker
    boot-end-marker
    enable secret 4  *************
    enable password *************
    no aaa new-model
    system mtu routing 1500
    ip routing
    spanning-tree mode pvst
    spanning-tree extend system-id
    vlan internal allocation policy ascending
    interface FastEthernet0
    no ip address
    no ip route-cache
    interface GigabitEthernet0/1
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/2
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/3
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/4
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/5
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/6
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/7
    switchport access vlan 2
    switchport mode access
    spanning-tree portfast
    interface GigabitEthernet0/8
    switchport access vlan 2
    switchport mode access
    spanning-tree portfast
    interface GigabitEthernet0/9
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/10
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/11
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/12
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/13
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/14
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/15
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/16
    switchport access vlan 3
    spanning-tree portfast
    interface GigabitEthernet0/17
    switchport access vlan 3
    interface GigabitEthernet0/18
    switchport access vlan 3
    interface GigabitEthernet0/19
    switchport access vlan 3
    interface GigabitEthernet0/20
    switchport access vlan 3
    interface GigabitEthernet0/21
    switchport access vlan 2
    interface GigabitEthernet0/22
    switchport access vlan 3
    interface GigabitEthernet0/23
    switchport access vlan 3
    interface GigabitEthernet0/24
    switchport access vlan 3
    interface Vlan1
    no ip address
    shutdown
    interface Vlan2
    ip address 10.0.0.1 255.255.0.0
    interface Vlan3
    ip address 192.168.0.2 255.255.255.0
    ip http server
    ip route 0.0.0.0 0.0.0.0 192.168.0.1
    line con 0
    line vty 0 4
    password *************
    login
    line vty 5 15
    password *************
    login
    end

    What Alain is saying is that you have two subnets listed in your switch. The comcast modem may support static routes, but it may only support natting it's primary IP address that's configured on its lan. For example, from your config I assume that vlan 3 is the vlan that the comcast modem is configured as. If you were to change the lan side ip address on the modem to vlan 2, your vlan 2 would be able to get out, but vlan 3 would not. The only way that I can see getting around this is to get a router, or ASA, and put it between your comcast modem and switch. Have the public address passed to the router/ASA and then you can do your natting on that device.
    HTH,
    John
    *** Please rate all useful posts ***

  • Uc560 - CUE Webinterface not reachable

    Hello,
    i have a problem with my UC560. Especially with the CUE Webinterface. After config my UC560 everthings working fine.
    But the webinterface of the CUE is not reachable. I can ping the integtr. Service. Engine with IP 10.1.10.1. from my network.
    A service-module integr.S.E. status reports -> everything OK. A seesion on CLI also connects and works.
    Is there any idea ? help !!!
    here some configs :
    interface Integrated-Service-Engine0/0
    description Interface used to manage integrated application modulecue is initialized with default IMAP group
    ip unnumbered Vlan90
    ip nat inside
    ip virtual-reassembly in
    service-module ip address 10.1.10.1 255.255.255.252
    service-module ip default-gateway 10.1.10.2
    interface GigabitEthernet0/1/3
    description Interface used to communicate with integrated service module
    switchport access vlan 90
    no ip address
    service-module ip address 10.1.10.1 255.255.255.252
    service-module ip default-gateway 10.1.10.2
    interface Vlan90
    description $FW_INSIDE$
    ip address 10.1.10.2 255.255.255.252
    ip access-group 103 in
    ip nat inside
    ip virtual-reassembly in
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http path flash:/gui
    ip dns server
    ip nat inside source list 1 interface GigabitEthernet0/0 overload
    ip route 10.1.10.1 255.255.255.255 Vlan90

    Hello,
    I have a similar issue. I know that there are many threads like this but this is the newest I found
    I've wiped the preloaded configuration and now using the uc560 like a standard ISR. I've made a lot of tests and changes, using G0/0 and an IP for connecting to the LAN, or g0/1/0 as trunk/access port connecting to the LAN. I've ended up with the configuration I'm attaching. There is no way to have connectivity with the CUE. I've tried with and without VLANs (the file attached is with VLANs). NAT is irrelevant in my case since there is not anything to translate it's all a private routed network. I still cannot ping the ISE inf from inside the uc560 localy or the gateway address from inside the CUE.
    This G0/1/3 seems to need some special configuration to be done in order to work. Do you know what is it?
    It's also not possible to make the CUE to factory default. No initial setup wizard starts... nothing. No wizard needed for the initial setup like all the other CUE products?
    Here is the config:
    !         interface GigabitEthernet0/0 no ip address duplex auto speed auto h323-gateway voip interface!interface Integrated-Service-Engine0/0 description Loopback interface used to manage integrated application module ip unnumbered Vlan2 service-module ip address 192.168.2.254 255.255.255.0 service-module ip default-gateway 192.168.2.2!interface GigabitEthernet0/1/0 switchport access vlan 2 no ip address!interface GigabitEthernet0/1/1 no ip address!interface GigabitEthernet0/1/2 no ip address!interface GigabitEthernet0/1/3 description Interface used to communicate with integrated service modue switchport access vlan 2 no ip address service-module ip address 192.168.2.254 255.255.255.0 service-module ip default-gateway 192.168.2.2!interface BRI0/1/0 no ip address isdn switch-type basic-net3 isdn point-to-point-setup trunk-group isdn 5!interface BRI0/1/1 no ip address isdn switch-type basic-net3 isdn point-to-point-setup trunk-group isdn 6!interface BRI0/2/0 no ip address isdn switch-type basic-net3 isdn point-to-point-setup!         interface BRI0/2/1 no ip address isdn switch-type basic-net3 isdn point-to-point-setup!interface Vlan1 no ip address!interface Vlan2 ip address 192.168.2.2 255.255.255.0!ip forward-protocol ndip http serverno ip http secure-serverip http path flash:/gui!ip route 0.0.0.0 0.0.0.0 192.168.2.1ip route 192.168.2.254 255.255.255.255 Integrated-Service-Engine0/0!!!telephony-service no auto-reg-ephone max-ephones 15 max-dn 15 ip source-address 192.168.2.2 port 2000 secondary 192.168.2.3 rehome 15 time-zone 28 time-format 24 max-conferences 4 gain -6 moh flash:/media/music-on-hold.au multicast moh 239.0.0.1 port 16384 route 192.168.2.2 web admin system name admin password cisco time-webedit transfer-system full-consult create cnf-files version-stamp 7960 Mar 06 2013 15:02:09!
    Thanks in advance!

  • Some dhcp clients not reaching internet

    This afternoon, I noticed that my iPhone was no longer reaching the internet. Later, we noticed my husband's (new!) iPad and my son's MacBook were not reaching the internet either. At least my MacBook was still reaching the internet. In all cases, the connectivity with the airport was fine; 4-5 bars, most of the time. All were connected yesterday, I believe. We made no real changes. I had my iPhone right next to my MacBook and both had good connections to the wifi, but only the MacBook was reaching the Internet.
    I went into Airport Utility and looked at the Time Capsule and found a long list under DHCP clients (maybe 9), but only 4 on the wireless clients list. I researched the issue, finding very little except generic suggestions (update software and reset the Time Capsule). The software was up to date; resetting it did fix the problem, at least for now. I am concerned it will happen again.
    Our airport devices:
    - Time Capsule running 7.5.2
    - 2 Airport Expresses, also running 7.5.2.
    Most, if not all, our wifi devices are up to date, including my MacBook running 10.6.5 and my iPhone running 4.2.1.

    I'm not sure this is quite the same since simply restarting our Time Capsule fixed things for us. It is annoying since I don't want to have to restart the Time Capsule every week or so when it fails this way, but restarted did fix this, at least temporarily.
    Another possibility I came across is that an ISP might limit the number of devices you can connect to the Time Capsule, but that wasn't the case for us. I'm thinking the Apple person you talked to probably checked on this, though.
    Hope you can figure it out!
    - Liz, aka liz4cps

  • Ethernet is connected but I can not get internet

    I just moved into a new apartment and my internet connect is through an Ethernet cord. I can not reboot or restart the connection becuase it is through my entire building. When I plug the Ethernet into my MacBook Pro is says it is connected however when I open Safari or Chrome it has no connection. My IP address starts with 169 and my Mask is 255. I have restarted the computer many times and have gone through the "Assist Me.." or "Diagnostics" within Networks however each one requires that I reboot the router. Seeing that I dont even know where the router is, I can not do this action. Can someone please help with this? I have also reset PRAM and looked at other threads that say delete "com.apple.afl", however in my preferences there is no "com.apple.afl". The ethernet is currently working on an HP desktop and I have made sure the broadban connection has been set to "share with other devices". I feel Im running out of options. PLEASE HELP!

    From the menu bar, select
     ▹ System Preferences ▹ Network ▹ Advanced ▹ TCP/IP
    From the menu labeled Configure IPv4, select
    Using DHCP
    Click Apply. See whether the IP address changes.

Maybe you are looking for