Uc560 fxo port not answering incoming calls

Hi,
My customer is facing problem for incoming calls in uc560 fxo port.They have 12 PSTN lines which is connected to UC system.System is configured with Auto-Attendant also. almost all days they are facing this major issue of incoming call is not getting answered by UC560 and caller can hear the line is ringing.While the time of this problem I can see some of the FXO port status LED is UP and not disconnecting even if no one is on call also.Once remove the cable from the FXO port and connect it back the problem will solve for time being.What will be the reason for this issue of line getting held.Is there any configuration needs to change in FXO module? Below is the configuration I done on all 12 FXO ports. Please check and
suggest me a solution.

HI Paolo,
Thank you provoding the proper documentation .
On the system side I made the change by keeping companding type from a-law to u-law and enabled battery reverse.This setting works fine for last three days and now again the customer is facing the same problem of FXO port get held and incoming calls are just ringing and system is not answering even.
How to get proper solution for this issue????
Please help me............
Regards,
Rinchuraj

Similar Messages

How to check UC560 FXO Port Not Problem Question

Dear All,
We are newbie on Cisco UC560.
Our customer use Cisco UC560, ESW-520-24P and Cisco SPA 502G and 508G for their branch office replace old traditional PBX. Cisco UC560 have built-in VIC2-4FXO and VIC2-4FXS.
Our customer PSTN line connected to UC560 FXO port (1 line PSTN).
We receive report from our customer that they cannot make a call to PSTN and receive call from PSTN that connected to UC560 FXO port (on physical FXO port LED Green turn on). When the problem happen our customer has restart UC560 or shutdown FXO port from CLI.
We have do some test to our customer UC560.
- Moving PSTN line to another FXO port (example: port from 0/1/0 to 0/1/1). The result is same (cannot make call to PSTN and receive call from PSTN)
Today, We have checked on our customer UC560 via show voice port summary and found that port0/1/2 and 0/1/3 OPER status is up wihout cable connected to this port.
Our question:
- What command on UC560 to make sure FXO port on UC560 doesn't have problem?
We attach:
show tech-support voice
show tech-support
We hope you can give us information about this.
Thanks For Your Attention

Hi There,
If you cannot find the Indonesian "Disconnect Supervision" you may get away with using Singapores "Disconnect Supervision" as your carrier networks are similar to each other
Cheers,
David Trad.

Q10 not answering incoming calls

Incoming calls go right to voicemail.
Subject Title edited to reflect new topic.

OK. Well, that's a pretty ancient OS level...indeed, I don't think that's an OS version at all, but rather the "Software Release". Can you check again please?Article ID: KB23393 How to find the model number and OS version on a BlackBerry smartphoneFurther interesting is that you say you updated the software...strange that something so old would be an update, but I do not know what versions VZW has on their approved list, but that version is definitely quite old...maybe 25 or so updates behind what is truly current from BB. There were many more 10.2.1 releases, then 10.2.2, then 10.3.0, then 10.3.1, and now 10.3.2...each with several versions (at the 4th octet) within. Did you check, in the phone settings, the "Call Forwarding" items to make sure that none of those are set? Failing all of this, the only thing I could recommend is a clean OS reload, and to an OS level that is much more current. If the behavior continues after, then I'd say it's back to VZW to look even deeper into their system. Good luck!

2811(NM-8AM) does not answers incoming call from PC

Dear friends,
We are planning to setup an out of band management connectivity, in our test setup we have a Cisco 2811 ISR (with IOS 12.4(9)T5 ) with NM-8AM (Analog modem module) installed.
Test Setup:
1. One Analog line (PSTN) connected to PC via built-in modem
2. Second Analog line (PSTN) connected to Cisco 2811 (NM-8AM) terminated on the analog modem module
3. Both the analog lines are working fine.
Test Scenario:
1. The router should accept the incoming call from PC. And from the PC we should be able to telnet into the router via dial up connectivity (Out of band)
Test procedure:
1. The Cisco 2811 router is configured as follows:
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Dial-Up-CPE
boot-start-marker
boot-end-marker
logging buffered 16384 debugging
enable password cisco
ip cef
voice-card 0
no dspfarm
username cisco password 0 cisco
interface Loopback0
ip address 10.10.10.1 255.255.255.255
interface FastEthernet0/0
ip address 20.20.20.1 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Group-Async1
ip unnumbered Loopback0
encapsulation ppp
dialer in-band
dialer idle-timeout 600
dialer-group 1
async mode interactive
peer default ip address pool DIALIN
ppp authentication pap chap
group-range 1/0 1/7
ip local pool DIALIN 172.16.16.1 172.16.16.5
ip http server
no ip http secure-server
dialer-list 1 protocol ip permit
control-plane
line con 0
exec-timeout 0 0
line aux 0
exec-timeout 0 0
password cisco
modem InOut
transport input all
stopbits 1
speed 38400
flowcontrol hardware
line 1/0 1/7
modem InOut
transport input all
stopbits 1
flowcontrol hardware
line vty 0 4
password cisco
scheduler allocate 20000 1000
2. With the above configuration, the router is not able to answer the incoming call from the PC.
3. And from the PC we are able to dial to a PSTN number at the router side, PC gives a proper dial tone and once the number is dialed, the call is landed on the other side (router end) and it rings continuously. But, the router does not answer this incoming. The analog line at the router end is terminated on async interface 1/0.
As I am new to dialup connectivity with NM-8AM, Could some please suggest the proper configuration in our router configuration OR Are missing any commands?
Any links/references would be of great help.
Thank you
Pradeep

Hi,
I guess I'm having exactly the same setup. The integrated modem on the other end does pick up the call but soon disconnect after displaying "Waiting for carrier".
Any clue?
Thanks,
Eyad

Z10 not answering incoming calls

I have a weird new issue with my z10 (my only issue so far). When an incoming call happens, the screen goes to the PHONE app and freezes there. I cannot do anything to answer the call. Then when the person leaves me a voicemail, I can't get the dialpad to appear to put in my voicemail password. The screen is still frozen on the PHONE app page. I can close that app but the call remains open and if I click on the call (at the bottom left of the screen), it simply goes back to the PHONE app page where I can't press on anything or do anything except swipe up to close the app.
Solved!
Go to Solution.

Did you reboot the device by removing the battery?
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

HT204387 My Iphone 4S will not allow me to answer incoming calls on any bluetooth headset without selecting it from the audio source menu.

My Iphone 4S will not allow me to answer incoming calls on any bluetooth headset without selecting it from the audio source menu.The connection works because once I do select the device...I can hear and speak. Any ideas?

Thank you templeton peck, I just rang them, turns out my contract doesn't allow it!

UNABLE TO SEE/ANSWER INCOMING CALLS. Instead, there is a "call status" button in lower left hand corner of screen...

UNABLE TO SEE/ANSWER INCOMING CALLS. Instead, when there is an incoming call, there is a "call status" button in lower left hand corner of screen...if i try to select the "call status" button, it does not do anything. Is this a reception issue? Very strange.....please help!!!!
Post relates to: Treo Pro T850 (Sprint)

yeah, that's pretty strange. i suggest to try soft reset first and then if it's still showing the same behavior. do a hard reset. that should help. however if it's still acting strange, you call the palm tech support hotline. 1-877-426-3777. they will help you with your sprint treo pro.

I can't put call on hold to answer incomming call, always hangs up on first call

I can't put call on hold to answer incomming call, always hangs up on first call

The procedure is different, depending on whether your carrier uses CDMA or GSM. Consult the manual. gdgmacguy gives directions on how to find it in the post above.
Best of luck.

Can't switch over to answer incoming calls on my white 4s

I am having difficulty click over to answer calls or even hanging up calls. I have to press the button constantly to get it to work. By then, I have lost the call. My sister has an iPhone 4s black and she is having the same issue. I wasn't having that problem when I had the 4 with the new update but I am having an issue now!
Help!!!!

I have the same problem with my new droid incredible. I've taken the battery out and restarted several times. The scenario is that my phone is in my pocket, someone calls, it prompts me to slide the bar up or down to answer or ignore......then i get a completely unresponsive screen. It will not answer my call.
This is definitely unacceptable. I can't have a phone that doesn't answer calls. This has happened a dozen times in the past 3 weeks.
Please help!!!

Why i can't change the volume in my headphone or answer incoming call or skip song's

hello
i get my new iphone 4- 1 day ago i connect my original headphone but i noticed that i only can listen to the music but
i can't change the volume or answer incoming call or skip song with doubel click.
hope you can help me.
danny

thank you onicray but.
when i put my serial number in the apple support of my iphone 4 that my friend buyt for me in hong-kong - i get the massage that i don't have 90 day of free support.
i buy it - 5/18/11 and now i am in israel.
i don't know what the reason.
can somone have any .....halpful .

FXO port not going back onhook when call goes to CUC Voice mail.

HI All,
Quiet new to the voice world and have just set up a home lab and have run into the following problem.
When a call comes in from the PSTN and gets transferred to voicemail CUC, when the caller has left the message and hung up the FXO port on my Cisco 3825 does not go back on hook
If a call comes in from the PSTN and is answered on a phone registered to the CUCM and the internal user hangs up the FXO port goes back on hook but if the caller hangs up the FXO port does not go back on hook.
I am using H.323 between the 3825 & CUCM
PSTN ------->Voice Gateway 3825-------->CUCM-------->CUC
Anyone got any ideas as to why this is happening?
Thanks

Hi Shaun,
The router DSP port is not able to detect the disconnect tone sent by provider that is why FXO port is remaining off hook. When call is answered by IP phone then IP phone user can listen the disconnect tone when PSTN caller disconnectes the call and they will hang up the call so gateway is aware that call is disconnected and moves the port to ON hook state but CUE cannot understand the tone so it keeps the call active. To resolve the issue we ave to configure custom CPTONE. Kindly collect PCM capture for a test call. Disable capture after call is disconnected by PSTN caller. i have attached the document. Use the method according to your IOS version.
Using PCM capture we can findout the exact frequency and cadence of the disconnect tone sent by provider.

FXO does not work incoming or outgoing

Hi all,
I have an CME with 8.5 release and I inserted an VIC2 - 4FXO.
I configured the FXO Port as below:
voice-port 0/0/0
trunk-group ALL_COT
supervisory disconnect dualtone pre-connect
cptone PT
timeouts initial 5
timeouts interdigit 7
connection plar 201
caller-id enable
dial-peer voice 100 pots
corlist outgoing chamada-emergencia
description ** Outside Calls **
destination-pattern 6..
port 0/0/0
forward-digits all
Every time I tried to make a call I receive busy tone and when I see the status of the port I see:
Foreign Exchange Office 0/0/0 Slot is 0, Sub-unit is 0, Port is 0
Type of VoicePort is FXO
Operation State is DOWN
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 128 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 1000 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is plar
Connection Number is 201
Initial Time Out is set to 5 s
Interdigit Time Out is set to 7 s
Call Disconnect Time Out is set to 60 s
Power Denial Disconnect Time Out is set to 1000 ms
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for PT
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Caller ID Info Follows:
Standard BELLCORE
Caller ID is received after 1 ring(s)
Translation profile (Incoming):
Translation profile (Outgoing):
lpcor (Incoming):
lpcor (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is dualtone pre-connect
Answer Supervision is inactive
Hook Status is Off Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Percent Break of Pulse is 65 percent
GuardOut timer is 2000 ms
Minimum ring duration timer is 125 ms
Hookflash-in Timing is set to 600 ms
Hookflash-out Timing is set to 400 ms
Supervisory Disconnect Timing (loopStart only) is set to 350 ms
OPX Ring Wait Timing is set to 6000 ms
Secondary dialtone is disabled
Operation stus DOWN; also when I do hut and no shut the voice port stays on DORMANT status and the I receive the message:
Apr 20 14:47:10.671: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
Can you help on this, why my FXO is not working?
Even when I call the the line the line rings but on the CME the extension plar does not start ringing.
My country is PORTUGAL.
Best Regards,
Jose Carlos Silva

Hi Jose,
Firstly is this a UC-500 based CME? I am not aware of a 8.5 version for the UC-500 unless this is a pre-production release, as far as I am aware the UC-500 is only supported up to 8.1 at this stage.
It would also be good if you could provide a copy of your running configuration (With sensitive data removed like usernames and or passwords and peoples names and numbers), this will help us in understanding the system configuration.
It also seems that the system has not been configured with CCA as there are no identifying markers in the configuration you posted that would indicated this was a CCA build, which leads me to think that this is a CLI build right??
I am personally not very ofay with the Portugal carrier setup so I best not post up a configuration of what the Voice-Port looks like as it might not be compatible with your local carrier, but I am curious as to why your FXO ports start at 0/0/0 typically on a UC-500 system they would start at 0/1/0 as the first 4 voice ports are normally reserved for FXS (Unless of course this is different for your region), which again makes me wonder if this is a UC-500 system or maybe an ISR (2800 series or above)??
Please post up your configuration it will help out a tremendious amount.
Cheers,
David.

Asterisk not seeing incoming calls

I have Skype Connect set up and an asterisk box set up to use it. I can succesfully call out from asterisk, but I do not see any incoming calls on the number assigned to my Skype Connect Profile. If I call the number it rings a few times then gives a busy signal.
Here is my sip.conf:
[general]
context=from-skype ; Default context for incoming calls
allowoverlap=no ; Disable overlap dialing support. (Default is yes)
udpbindaddr=0.0.0.0 ; IP address to bind UDP listen socket to (0.0.0.0 binds to all)
bindport=5060
bindaddr=0.0.0.0
tcpenable=yes ; Enable server for incoming TCP connections (default is no)
tcpbindaddr=0.0.0.0 ; IP address for TCP server to bind to (0.0.0.0 binds to all interfaces)
srvlookup=yes ; Enable DNS SRV lookups on outbound calls
notifyhold = yes ; Notify subscriptions on HOLD state (default: no)
sendrpid=yes
register => 9905XXXXXXXX:[email protected]/9905XXXXXXXX
[skype]
type=peer
context=from-skype
username=9905XXXXXXXX
secret=Redacted
canreinvite=no
insecure=port,invite
dtmfmode=rfc2833
host=sip.skype.com
realm=sip.skype.com
nat=yes
qualify=yes
fromuser=9905XXXXXXXX
fromdomain=sip.skype.com
disallow=all
allow=g729
allow=ulaw
allow=alaw
trustrpid=no
sendrpid=yes
[1001]
type=friend
callerid=1001
canrevinite=no
dtmfmode=rfc2833
mailbox=1001
disallow=all
allow=ulaw
transport=udp
secret=password
host=dynamic
context=default
And my extensions.conf
[general]
static=yes
writeprotect=no
[globals]
TRUNK=Skype
[default]
[from-skype]
exten=>9905XXXXXXXXXX,Noop(${CALLERID(name)} , ${CALLERID(num)})
exten=>9905XXXXXXXXXX,n,Dial(SIP/1001,30,t,r)
exten=>9905XXXXXXXXXX,n,voicemail(100|u)
exten=>281203XXXX,Noop(${CALLERID(name)} , ${CALLERID(num)})
exten=>281203XXXX,n,Dial(SIP/1001,30,t,r)
exten=>281203XXXX,n,voicemail(100|u)
The last 3 lines were my best guess at how to tell it what the incoming call phone # is and I'm not sure it's entirely necessary. Any thoughts?

Dear MRLindstrom,
I am sorry to hear that you are having issues receiving incoming calls to your Skype Connect Online number.
In looking at your Asterisk configuration, I would suggest changing your 'incoming call field' (the last 3 lines you have included below) to your 9905xxxxxxxxxx, rather than 281203xxxx.
Please make that change and let us know if you are able to receive calls.
Thank you,
MariaA
Skype Enterprise Support

Not getting incoming call while using Internet on ...

Hello Friends,
I have Nokia E63 and data plan from my mobile service provider. When I listen Internet Radio, it’s not allowing any incoming call, no screen intimation of incoming call nothing. May be i am missing some setting or so!
I would really appreciate any help of this
E 63 user

Hi...Please check the Burst Control file with the printer & IP details.
Look for the file below.
<?xml version="1.0" encoding="UTF-8"?>
<xapi:requestset xmlns:xapi="http://xmlns.oracle.com/oxp/xapi">
<xapi:globalData location="stream">
</xapi:globalData >
<xapi:request select="/DATA/LIST_DEPT/DEPT/LIST_EMPLOYEE/EMPLOYEE">
<xapi:delivery>
<xapi:email server="${EMAIL_SERVER}" port="${EMAIL_PORT}"
from="${FROM_EMAIL_ADDRESS}"
reply-to ="${REPL_TO_ADDRESS}">
<xapi:message id="email1" to="${TO_EMAIL_ADDRESS}" cc="${CC_EMAIL_ADDRESS}"
attachment="true" content-type="html/text"
subject="Employee Report for Empno ${EMPNO}">
Dear ${ENAME}, Please review the attached document.</xapi:message>
</xapi:email>
<xapi:filesystem id="file1"
output="C:\burst\sample\${EMPNO}_${ENAME}_${MGR}_PRINT.pdf"/>
<xapi:print id="print1" printer="${PRINT_URL}" copies="2"
orientation-requested="3" />
</xapi:delivery>
<xapi:document key="${EMPNO}"
output-type="pdf" delivery="email1">
<xapi:template type="rtf" location="${TEMPLATE_LOC}"
filter=".//EMPLOYEE[DEL_CHANNEL='EMAIL']" >
</xapi:template>
</xapi:document>
<xapi:document key="${EMPNO}" output-type="pdf" delivery="print1">
<xapi:template type="rtf" location="${TEMPLATE_LOC}"
filter=".//EMPLOYEE[DEL_CHANNEL='PRINT']" >
</xapi:template>
</xapi:document>
<xapi:document key="${EMPNO}" output-type="pdf" delivery="file1">
<xapi:template type="rtf" location="${TEMPLATE_LOC}"
filter=".//EMPLOYEE[DEL_CHANNEL='FILE_SYSTEM']" >
</xapi:template>
</xapi:document>
</xapi:request>
</xapi:requestset>
check the printers setting as required....aslo check what printer you are using for pdf printing...Pasta Printing??
Thanks
Ratnesh

Restrict FXO ports on the Outgoing Calls.

I need to configure a restriction on the Outgoing Calls, i need the extension that start whit 1 (100,101,102,etc..) to only use the FXO ports 0/1/0 0/1/1 0/1/2 and the extensiones that start whit 2 (200,201,202,etc...) to only use the FXO ports 0/2/0 0/2/1 0/2/2, how can i make this happen ?

Hello Mario,
First off, this is not possible with CCA, this can only be done though CLI.
1. Setup seperate PSTN Trunk Groups. A: 0/1/0, 0/1/1, 0/1/2 B: 0/2/0, 0/2/1, 0/2/2
2. Setup Dial-Peers for each Trunk Group.
3. Setup COR list to restrict which users can use either Trunk Group.
That is the simple explaination, the actual setup can get quite complicated and lengthy.
Thank you,
Darren

Uc560 fxo port not answering incoming calls

Similar Messages

Maybe you are looking for