UC560 fxo with 4FXO VIC card.
Just wanted to confirm before purchasing how the UC560 handles PSTN Analog lines. We have 8 analog lines each with a different number.. example 123-456-7899, 123-456-7898, 123-456-7897 etc....
If the office wants to use one of the numbers as the "main" office number how would the UC560 handle the incoming calls? If someone dials the main number, lets say it will be 123-456-7899, what happens when a 2nd person dials it? Will the UC move that incoming call to another FXO port just like when doing outbound calls? If it works the way I mention above, that would allow for 8 people to call in on that 1 line and it will be spread between all 8 fxo ports.. does that sound correct?
Or, does the teleco company have to due the hunting for us?
Any insight would be appreciated.
Thanks,
J
Yes, telco has to do it. System cannot control how telco routes incoming calls. So, one has to ask telco to setup an hunt group, and define which addtional lines it will re-hunt calls. Depedning on situation these line can be incoming only, or bidirectional. In this case, special care must be give to the CO and system hunt scheme to minimize glare.
Also, please note if using a bunch of analog lines like you're planning, that will not get the best results to the users, like fast dialing, immedaite CLID display, automatic hunt as described above, DID service, digital voice quality, etc. For best results, one should only use ISDN PRI, or SIP trunk.
Finally, but very important: unless you have significant amount of expereince with telephony and netwrok, it is strongly recommened that for sure and quick results you get an UC certfied Cisco partner, or person of equivalente knowledge and expereince.
Similar Messages
-
2800 config with 4FXO VIC, voice-ports?
I'm trying to configure the voice-ports on a 2800 router with a 4 port FXO VIC and when I issue the voice-port command it only shows ports 50-50 so I use
voice-port 50/0/1 and it comes back with invalid input at marker and it points to the 50.
boot-start-marker
boot system flash flash:c2800nm-ipvoice-mz.124-4.T.bin
boot system flash flash:c2800nm-spservicesk9-mz.123-8.T8.bin
boot-end-marker
Lights on the FXO card are lit up but I do not have any cables plugged into them, am I missing something?
ThanksI'm guessing this is the info on the pvdm2?
WIC Slot 1:
2nd generation - FXO Voice daughter card (4 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-21589-01
Board Revision : E0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC092447VB
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00 -
How to check UC560 FXO Port Not Problem Question
Dear All,
We are newbie on Cisco UC560.
Our customer use Cisco UC560, ESW-520-24P and Cisco SPA 502G and 508G for their branch office replace old traditional PBX. Cisco UC560 have built-in VIC2-4FXO and VIC2-4FXS.
Our customer PSTN line connected to UC560 FXO port (1 line PSTN).
We receive report from our customer that they cannot make a call to PSTN and receive call from PSTN that connected to UC560 FXO port (on physical FXO port LED Green turn on). When the problem happen our customer has restart UC560 or shutdown FXO port from CLI.
We have do some test to our customer UC560.
- Moving PSTN line to another FXO port (example: port from 0/1/0 to 0/1/1). The result is same (cannot make call to PSTN and receive call from PSTN)
Today, We have checked on our customer UC560 via show voice port summary and found that port0/1/2 and 0/1/3 OPER status is up wihout cable connected to this port.
Our question:
- What command on UC560 to make sure FXO port on UC560 doesn't have problem?
We attach:
show tech-support voice
show tech-support
We hope you can give us information about this.
Thanks For Your AttentionHi There,
If you cannot find the Indonesian "Disconnect Supervision" you may get away with using Singapores "Disconnect Supervision" as your carrier networks are similar to each other
Cheers,
David Trad. -
Uc560 fxo port not answering incoming calls
Hi,
My customer is facing problem for incoming calls in uc560 fxo port.They have 12 PSTN lines which is connected to UC system.System is configured with Auto-Attendant also. almost all days they are facing this major issue of incoming call is not getting answered by UC560 and caller can hear the line is ringing.While the time of this problem I can see some of the FXO port status LED is UP and not disconnecting even if no one is on call also.Once remove the cable from the FXO port and connect it back the problem will solve for time being.What will be the reason for this issue of line getting held.Is there any configuration needs to change in FXO module? Below is the configuration I done on all 12 FXO ports. Please check and
suggest me a solution.HI Paolo,
Thank you provoding the proper documentation .
On the system side I made the change by keeping companding type from a-law to u-law and enabled battery reverse.This setting works fine for last three days and now again the customer is facing the same problem of FXO port get held and incoming calls are just ringing and system is not answering even.
How to get proper solution for this issue????
Please help me............
Regards,
Rinchuraj -
Mac with airport card and PC with wi-fi card
Hi!
I just bought my first mac, and strange, but I have problems connecting my mac via airport extreme card to my wi-fi card (as computer-to-computer or ad-hoc mode) on my PC. I am not using base station or any wi-fi router, just two computers with their internal cards.
PC has WinXP pro with SP2 and mac - imac g5. The problem is that both of the cards are enabled and are working on 100%, but they do not see each other! I tried to create a wireless network on my PC and then search for this network from mac and vice versa - nothing. By the way my notebook finds the PC's newly created network with no problem, but not the mac.
What could be wrong? Is it possible, that it's nessesary to use the base station with them?
iMac G5 Mac OS X (10.4.3) OS Tigeranyone?
-
C460-M2 with 2 VIC-1225, managed by UCSM
C460-M2 with 2 VIC-1225; all documents show only one VIC-1225 (which has to be in PCI slot nr.1) single wire managment with a UCS FI ?
Is this a limitation ? or must the second VIC-1225 be connected to a switch outside the FI ?
Walter.I received the following answer
Good question Walter. The documentation is confusing. If running the C460 as part of a UCS integration, only 1 card is supported.Although the server supports 2 cards , slot 1 & 2 according to the specsheet. The datasheet states that upto 3 VIC can be supoprted int he server.
The Cisco CCW config tool allows you to configure 2 VIC1225 in the C460.
From the 460 spechseet.
http://www.cisco.com/en/US/prod/collateral/ps10265/ps10493/ps11587/spec_sheet_c17-662220.pdf
Page 24
The C460 server accommodates the Cisco 1225 Virtual Interface card, which is supported only in slots 1 and 2. Note, however, that if the server is running UCSM, only slot 1 is supported for the VIC card.
■ The Cisco Card NIC mode is currently supported only with a Cisco 1225 VIC (UCSC-PCIE-CSC-02) that is installed in PCIe slot 1.
■ The C460 server accommodates the Cisco 1225 Virtual Interface card, which is supported only in slots 1 and 2. Note, however, that if the server is running UCSM, only slot 1 is supported for the VIC card.
From the datasheet
http://www.cisco.com/en/US/prod/collateral/modules/ps10277/ps12571/data_sheet_c78-708295.html
System Requirements
The Cisco UCS VIC 1225 is designed for use only on Cisco UCS C-Series Rack Servers. A single Cisco UCS VIC 1225 is supported on Cisco UCS C260 M2, C460 M2, C220 M3, C240 M3, C22 M3, and C24 M3 rack servers. Up to three Cisco UCS VIC 1225 cards are supported on these servers depending on the slot configuration.
Anyone at Cisco want to clarify the above?
Message was edited by: NABIL YAGHI -
SQL Clustering on C Series server with QLE8152-CNA cards
Is there any documentation on best practices when installing Windows on a c series server
with QLE8152-CNA cards for SQL clustering? Since it will be a bare metal install of Windows, this card will only present a maximum of 2 nics (FI A and FI B) to the Windows OS and because SQL clustering requires multiple nics (heartbeat, regular network), I wanted to know whethere there are guidelines on how to do this or whether it is even supported. I intend on using the failover feature in UCS Manager 1.4 when creating a service profile for these c series server which means I'll end up with 1 NIC presented to the Windows server. Thanks.Hi Keny,
I tried to powercycle both servers (c260M2 and C460M2) but still no discovered server and also no logg.
I checked
Rack Server Discovery Policy == immediate
Rack management Connecton Policy == Auto Achnowledged
Chassis/Fex Doscovery Policy == 2 Link and Port-Channel (As I installed 2232PP I moved to Port Channel)
I am running UCSM Version 2.1(1e)
FI 6248 Version 5.0(3)N2(2.11e)
2232PP run on same as FI
I also have a connected 5108 with IOM 2104 running on 2.1(1e) Version.
CIMC Version of C260M2 and C460M2 will be checked tomorrow when my kolleague is in the datacenter.
Server Connection is not really the same like in http://www.cisco.com/en/US/docs/unified_computing/ucs/c-series_integration/ucsm2.1/b_UCSM2-1_C-Integration_chapter_011.html
Because I still have no VIC Card but the connections are the same.
C260 GE LOM1 <-> FEX2 Port 11
C260 GE LOM2 <-> FEX3 Port 11
C260 10 GE LOM1 (PCIE Slot4) <-> FEX2 Port 12
C260 10 GE LOM2 (PCIE Slot4) <-> FEX3 Port 12
GE LOM ist position 13 and 10 GE LOM is position 11 in the techspech of c260
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C260/install/overview.html#wp1243740
C460 GE LOM1 <-> FEX2 Port 10
C460 GE LOM2 <-> FEX3 Port 10
C460 10 GE LOM1 <-> FEX2 Port 9
C460 10 GE LOM2 <-> FEX3 Port 9
GE LOM ist postion 8 and 10 GE LOM ist position 7
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C460/install/overview.html#wp1243740
With C260 I also tried a reboot with disconnected 10 GE Ports, but also no discoverd Server until now.
Regards Alois -
Need help with Cisco Interface Cards???/
Hi, I purchased 4 WIC-1AM cards for my cisco 1760 gateway to use with cisco call manager server. I'm trying to figure out if I can even use these cards for voice cards to make calls inbound and outbound. I'm seing that the cards that CM gives me are all VIC cards listed and i don't see any WIC cards listed in the endpoint list on the CM for the gatway. So can I even use these cards for what I'm trying to do??? Please help???
ThanksIf i got the vontage sip account how would i hook it up to my CM Sever?
I'm using a 1760 gatway, what is a DSP resource?
When i do show diag I get this from my router:
show diag
Slot 0:
C1760 1FE VE 4SLOT DV Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 5.0
PCB Serial Number : FOC08077JDP
Part Number : 73-7167-05
Board Revision : B0
Fab Version : 04
Product (FRU) Number : CISCO1760
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 16 41 05 00 C1 8B 46 4F 43 30 38 30
0x10: 37 37 4A 44 50 82 49 1B FF 05 42 42 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Packet Voice DSP Module Slot 0:
Not populated
Packet Voice DSP Module Slot 1:
Not populated
WIC/VIC Slot 0:
One Port Modem WIC
Hardware revision 1.0 Board revision H0
Serial number 0034764142 Part number 800-08823-01
FRU Part Number WIC-1AM=
Test history 0x00 RMA number 00-00-00
Connector type WAN Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 38 01 00 02 12 75 6E 50 22 77 01 00 00 00 00
0x30: 88 00 00 00 06 02 10 01 FF FF FF FF FF FF FF FF
WIC/VIC Slot 1:
One Port Modem WIC
Hardware revision 1.0 Board revision H0
Serial number 0034764050 Part number 800-08823-01
FRU Part Number WIC-1AM=
Test history 0x00 RMA number 00-00-00
Connector type WAN Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 38 01 00 02 12 75 12 50 22 77 01 00 00 00 00
0x30: 88 00 00 00 06 02 10 01 FF FF FF FF FF FF FF FF
What do you think? -
How do I activate a used iPhone 3 with no SIM card for use as an ipod touch?
How do I activate a used iPhone 3G with no SIM card for use like an iPod Touch? It was apparently on AT&T previously and I have another iPhone 3 that is active on AT&T if that is helpful. Thanks!
Copied from the link provided.
Follow these steps to use your iPhone without a wireless service plan:
Insert the SIM card from your new, activated iPhone or one that was previously used to activate the original iPhone.
Connect the iPhone to iTunes on a computer connected to the Internet.
Once iTunes activates the device, you're free to use the iPhone as if it were an iPod touch. -
Dear sir
I bought my iPhone 4 from Apple store in Charlotte N/C about 2years ago without contract.
Now I tried to upgrade it to iOS 7.0.4.but after that my phone not work with last sim card.
And invalid sim appeared.so I bought it without contract but it seems to be lock in my country
Please tell me whats the matter?
My phone serial no 86034HTCA4T
Modem firmware 04.12.09
ThanksWithout contract is not the same as unlocked. The update to iOS 7 relocked
the iPhone to the wireless carrier to which it was originally locked. You must
contact that wireless carrier to see if they offer unlocking and if you qualify.
If you used jailbreak or other hack to unlock the iPhone initially, the method
used may prevent a legitimate unlock from succeeding and may render your
iPhone unuseable. -
Hello,
I have an iPhone 4S 32Gb White AT&T, product part No. MC921LL/A, Serial No. C39GMLPWDTDC
I bought this iPhone from Apple Retail Store (from Fifth Avenue, NY) for the full amount. Now it does not work with my SIM card only works with AT&T. I restored the phone several times, but I have not received "Congratulations your iPhone has been unlocked". Please activate my iPhone to work with different SIM cards
Thanks,
Best WishesWhen did you buy it?
Apple did not begin selling an unlocked version of the iPhone 4S in the US until 11/11/11. I believe it went on sale only through the online store at that time. I'm not sure if it's available at retail yet.
What you purchased was a phone without a contract commitment. It is still locked to AT&T. AT&T will NOT unlock iPhones for any reason. Return it and get your money back, then use that to purchase an unlocked phone. -
HT4059 How do I make ibook purchase with iTunes gift card rather than credit card on account.
How do I make ibook purchase with iTunes gift card rather than credit card on account.
go to settings- itunes app store- click appleid and view account - may need password - then under billing info select none. however it will auto use the gift card regardless first
-
Help with Airport Extream Card in PowerMac G5
Hello,
I have purchased a used Power Mac G5 with the following hardware:
Model Name: Power Mac G5
Model Identifier: PowerMac7,3
Processor Name: PowerPC G5 (3.0)
Processor Speed: 2.5 GHz
Number Of CPUs: 2
L2 Cache (per CPU): 512 KB
Memory: 2.5 GB
Bus Speed: 1.25 GHz
Boot ROM Version: 5.1.8f7
While it works perfectly, the machine didn't come with an airport card which I installed:
Wireless Card Type: AirPort Extreme (0x14E4, 0x4E)
Wireless Card Locale: USA
Wireless Card Firmware Version: Broadcom BCM43xx 1.0 (4.170.25.8)
The machine appears to recognize the airport card and I can "see" my home network but can not connect to it. When I enter the WEP password, it just fails to connect. I have 2 other macs in the house (and an iPhone) along with an HP windows laptop that connect to this network without issue, so I am confused.
I think there are (at least) 2 variables that I am unsure of:
One: Do I have the right airport card? As best I can tell, I do. But if anyone can tell from the hardware info I copied above, I'd welcome any info. I did see some posts about "late model dual core" G5s (labeled as model 10,x in system profiler) that needed a different card. I took the airport extreme card from one of my other macs (G4 Mirror Door) and the card works perfectly in that machine. I THINK it's the right card for the G5, but can't be sure.
Two: Do I have to install any software to configure the card on the computer.
What else should I be looking for?
Many thanks,
SteveHi-
The Airport Extreme card for the MDD FW800 model is the same as in the G5 up to Early 2005.
http://support.apple.com/kb/HT3024?viewlocale=en_US
Did you connect the antenna to the card correctly?
http://manuals.info.apple.com/enUS/AirPortCard.pdf
Did you connect the external antenna (T shaped, plug in rear of tower)?
http://support.apple.com/kb/TA27092
After proper installation, it should just be a matter of making adjustments to your network settings. -
I can't seem to update my apps or make any purchases on from my account. Nothing has changed with my credit card information and for some reason the iTunes Store tells me my information is incorrect. What do I do?
Yes, it's frustrating.
I don't have my iPod with me but, as I recall, the change is done in Settings/Store. That change will apply to NEW purchases. However, be aware that all purchases are permanently associated with the Apple ID that was originally used. Generally, it's only a problem when you need to update an app. IF you do your updating from iTunes and your logged in to the "wrong" ID, you'll need to log out and back in again. It's easier from the iPod as you do not need to log out/in but you do need to know the password.
Unfortunately, you can not merge IDs nor can you transfer purchases from one ID to another. Go here to find out exactly what you have. I have the same problem so I deliberately made both passwords identical to make things slightly easier for me. -
My iPod Touch battery is not working. I requested a repair through the Apple Support. On the final page, when I clicked the button that puts the info through with your credit card number, the resulting page gave an error (I wish I'd have saved it!). Anyhow, I checked my credit card and it was charged, so I assumed the repair request went through. The next day I received a form email saying my problem was with "Sync with iTunes (Not iCloud) - Data Backup/Migration (not iCloud)" instead of the battery repair. It also says for iPod customers, to send your iPod to Apple - but I had requested the "iPod Coffin" to be mailed to me so I could send it back. Obviously there was an error between the request and what was received, so I'd like to ask Customer Service about it. However, I can't find a way to contact them. When I replied to that form email, I recieved an automated reply saying emails there were not read. Anything online asks me to pay $19 and I don't have the correct issues to request an exception. The closest store is over an hour away or I'd simply go there to ask. What can I do?! Any suggestions you have are much appreciated. Thank you!
PS - The form email also says if I wait 10 days the repair request will be canceled. Does this mean my credit card will be refunded for the $85 battery replacement charge if it is canceled automatically?Thanks, but I've been on the phone with AppleCare US (where I am and live) and AppleCare UK. They continue bouncing me back and forth without helping resolve the problem.
Perhaps someones knows how to further escalate the issue at Apple?
Maybe you are looking for
-
Messages are in hold in the Adapter Engine
Hi all, I am seeing in my adapter engine that all of the messages are in status hold , it is for a specific business system and interface. 2009-02-10 21:41:30 Success Message successfully put into the queue. 2009-02-10 21:41:31 Success The message
-
In APP run Advances r getting picked
hi gurus, when i run APP advances to vendors are not getting picked, i have checked in fbzp, all settings are correct, can u pl,s tell me any setting have to done other than fbzp3 Thanks in Advance points are assured
-
ITunes 11.0.4 is shuffling music even when shuffle is turned off
Grrrr. This is really driving me nuts. I'm using 11.0.4 on my MacBook Pro (OSX 10.8.4). iTunes will shuffle the music I'm playing even when shuffle is turned off. It will finish track 1 of an album (for example) and then go to 9. or 11. or 7. What th
-
Hello, After a botleneck on our production system we noticed that average Roll Wait Time (ms) was very high = 25.218,8. We are still investigating the root cause of this bootleneck to avoid future issues... Do you have any idea about what tasks are i
-
While for both project and WBS the user status profile is assigned in the project profile, the network activity status profile is assigned in the network type. But where to default the network status profile? Or in the network type it should be for