UCCE Agent cannot answer call

Hi,
We are facing an issue some times (random) that agent cannot answer the customer call.
Before the agent answers the call, it is queued again and offered to another agent.
The new agent also faces the same issue.
We are using UCCE8, CVP8 in a comprehensive mode.The call is send to CVP(10.70.78.118)
from CUCM(10.70.78.126,10.128.60.31) through SIP trunk. The CVP application is played successfully
using the gateway(10.70.78.114). The agent extension label is correctly received in CVP & associated
SIP static route to CUCM(10.70.78.126) is identified. Upon routing the call to CUCM, the CVP log shows
"HANGUP with Call History" and "Terminated with Q.850;cause=16".
This issue is happening rarely & randomly. Will it be any issue with CUCM, network or CVP configuration.
CVP log is attached for the analysis.
Appreciate any help or suggestion.
Regards,
Nissar.

It seems that my analysis of the log is not correct. Sorry for misguiding, if anybody analysed the log.
"REJECTED WITH 503 - Service Unavailable Reason: Q.850;cause=47" is the correct error message from the call leg to agent. I was refering to the incorrect call leg in the previous post.

Similar Messages

CTI OS desktop agent cannot answer call

Hello All,
I am seeking a suggession on a issue which seems to be lying with network.
Agents are located in different location and all remaining Cisco components like ICM, CVP and CCM are in data center.
Agent succesfully logs in via CTI os Dsktop agent and IP phone, but when call is transferred, its state fluctuates between ready and reserved. CTI OS desktop agent never goes to talking state and call never lands on IP phone.
Network team claims nacessary routing and firewall ports are already open.
Seeking suggesion to further isolate and what logs/traces can be collected to identify the source of issue.
Tried 1 test agent login in data center and observed that in data center call lands to agent succesfully.
Any directions/pointers?
TIA
Regards,
Kailash

Hi Kailash,
Could you please check the below points:
1. Check if you associated the Agent phones to CCMPG user.
2.Symptom: Agent receives calls, but loses them after a few seconds before they can be answered.
Possible Cause The Ring No Answer feature is probably set on your ICM system. Open the ICM Configuration Manager and increase that value or disable it all together. (Refer to the ICM Administration Guide for Cisco ICM Enterprise Edition for more information on how to configure the Ring No Answer feature.)
3. Make sure the CSS and partitions are proper.
Also refer the below troubleshooting guide for more information,
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/ctios/ctios7_2/troubleshooting/guide/ctits.pdf
Hope it helps,
Anand
Please rate helpful posts by clicking on the stars below the right answers !!

Cannot answer calls, cannot slide to answer

I have the i phone 4, it works fine until some calls, the phone rings and when i attempt to answer by sliding to answer, the touch screen doesnt work, i can mute the ring but cannot answer...

Try to reset the phone by holding the sleep and home button until the Apple logo comes back again.
If this does not work, set it up again "as new device" How to back up your data and set up as a new device

Cannot answer calls using touch-screen

I am using G900, it is a touch-screen phone, I am unable to answer calls using the touch-screen option.
1) Is there any update required for the software for the same to work.
2) Can I change the settings in the mobile to answer calls using some key on the keypad.
Thanks
You can email me your replies on [email protected]

One question, does the touchscreen works on everything else?

Help! Cannot answer calls ever since update.

After I did an update, I can no longer answer calls. It's like the answer button is dead when I hit it but ignore button works fine. Seen somewhere that it could have something to do with the keyboard being locked but it's always been locked and I never had a problem before this. I have a BB Curve 8530.

Hi,
My suggestion would be to reload your software again on your device. From what you describe, it sounds like the software may have been corrupted. Make sure you load your device software from a computer and not wirelessly from your device. You can get all the software you need from Verizon right here. Hope this helps.
Doc

Agent cannot recieve call

Hi,
I have an agent configured in UCCX on a remote site. All of the CRS config should be correct and the agent can log on to the agent desktop. When a call is routed to the agent the status goes into reserved, then straight back to Not Ready (or Ready). the phone does not even ring which i suspect is the issue.
I think the problem is either;
a. Partition or CSS issue - this is the first agent on a remote site
b. Codec issue - i doubt it as the phone would ring first if there were a codec issue.
I have attached the MIVR but i think this is the issue;
The Resource to which the transfer failed is 3055
Cheers
Jon

Its ok i solved it myself, as suspected the CSS was the issue . the CTI ports did not have access to the remote partition.

Cannot answer calls on I phone 5.

The phone rings, actually it doesn't ring, it vibrates. Nothing shows up on the phone as per caller, ID or an answer option/page. If I go to the call pad screen on the PHONE icon, again its as tho no one is calling. The only reason I know it is an incoming call is from the vibration (which is enabled along with ringer) and then I get a missed call message! Soft reset will get me one or two calls then the same thing happens again. Tried hard reset, taking everything off and then putting it back on thru I tunes. Same thing. Any ideas peeps? Well frustrating, new phone?

Greetings jeffers59,
I can certainly understand your frustration at being unable to receive phone calls on your iPhone 5. I know it would bother me. Let's see if we can get you back up and running.
If you are having an issue with being unable to receive calls as you describe, and you have already tried resetting the iPhone, the next step would be to back up any data on the iPhone and then erase it and set it up as a new device. See this article for how to do so -
How to erase your iOS device and then set it up as a new device or restore it from backups
Thanks for using Apple Support Communities.
Best,
Brett L

Cannot Answer Calls from Lock Screen

I have all alerts and notifications enabled on the latest Skype for iOS app. I have deleted and reinstalled Skype. I have rebooted and restored my iPhone.
My problem is that even when I have the skype app running and my phone is in a locked state, when I go to unlock the phone to answer an incoming call Skype simply declines the call. I can find no combination or successful means to answer skype on my mobile if my phone is in a locked state.
How do I resolve this?

Same problem with i5 phone. The phone does not have a password but the call automatically drops when I slide to unlock to answer.

TS4185 I cannot answer calls from Face Time

I went to the store because Face Time does not function. They installed it again. Back home it worked. But now, after a few days Face Time again doens not work. I get a stroke throught Face Time screen.
How to solve

Same problem with i5 phone. The phone does not have a password but the call automatically drops when I slide to unlock to answer.

5800 - V40 - Cannot answer call using touch screen

Hi,
Just upgraded to V40 on my 5800. Now when the phone rings I get 2 options on the touch screen:
1. Answer
2. Unlock
Neither work. I know I can use the buttons, but why have the other options on the screen if they don't work. What about the other options like silence or reject, or send message. All gone.
The new version is **bleep**.
Also, when I set an alarm, I can't silence it, or stop it using the touch screen.
This all seems to happen when the phone is locked, but if the phone is unlocked, I get the older options.
I don't know how I'm expected to unlock my phone just before someone rings me to enable me to have all the existing options, or wake up before my alarm in order to unlock the phone, so I can snooze or stop it.
Can something be done, or can I revert back to V31??
Thanks,
DOS.
Solved!
Go to Solution.

they aren't buttons , they are ARROWS. don't tap to answer or silence the alarm , just swipe your finger in the same direction of movements to answer or snooze or .... etc
see this video:
http://www.youtube.com/watch?v=0bca1ebhGB8
-you can show appreciation to my posts if it helped or useful by pressing the green Kudo star beside my post that hepled
-if my answer was the solution , so click accept as solution button
Started From Nokia 3310 , Now with Nokia N97 v.22.0.110 + N900 PR1.2

Phone sometimes hang and cannot answer call using the unlock slider using version 4.3.3

I am using iphone with s/w version 4.3.3. Anyone can help me?

Try resetting the iPhone.
Press and hold the On/Off Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears.

UCCE 7.2.X - Calls Answered and Calls Handled

Has anyone experienced an issue in UCCE 7.2, where the calls answered does not seem to be reporting correctly? In this case we are seeing that the calls answered figure, is less than the call handled. The Handled figure seems to be correct when you take into consideration the calls offered, error calls, abandoned calls etc. Webview historic call type reports are reporting what is in the Call Type Half hour tables so not an issue with webview. We have tried to replicate various scenarios but cannot replicate the instance where the answered call is not counted. We have also reviewed the ICM scripts but have drawn a blank.
I have attached a copy webview report that shows the disparity we seem to be having. Any ideas would be much appreciated.
Regards
Cecil

Hi,
this is not necessarily an error.
- Calls Answered value increments when the call has been answered (the moment the agent picks up the phone).
- Calls Handled value increments when the call has been handled, in Cisco terminology, the wrapup state has ended.
If you take into consideration a simple fact, that a call may be answered within one reporting interval (in UCCE 7.2.x it's 30 minutes), and "handled" in the next interval, you can easily see two different numbers.
For instance, six customers call between 10:00 and 10:30. All calls are answered by an agent the moment they arrived. Five calls end before 10:30. But one of them is a demanding customer, and the call ends at 10:40. What you'll see is 6 for CallsAnswered but only 5 for CallsHandled.
Of course, CallsAnswered may be less than CallsHandled, too, it simply means there were calls that were answered within the previous reporting interval but handled in this interval.
G.

CVP call server logs - Hi All, I am trying to figure out whether caller party(End User) hangup the call first or UCCE Agent

CVP call server logs
Hi All,
I am trying to figure out whether caller party(End User) hangup the call first or UCCE Agent.
Attaching CVP call server Logs& UCCE TCD& Route Call Details for your reference.

From the CVP logs, it can be determined which side disconnected the call first. For each call, CVP keeps track each call leg. From Inbound Gateway to CVP is INBOUND leg, rest are OUTBOUND leg. You can then look at which leg the SIP BYE message is received first.
Since you have very basic log enabled, you will not see the exact SIP message. But it can be determined by the outcome of the message. Here is the snippet of the log during the disconnect:
Line 3766: 3083689: 10.180.245.43: Sep 12 2014 12:21:11.293 -0700: %CVP_8_5_SIP-7-CALL: {Thrd=DIALOG_CALLBACK.6} CALLGUID = CBCCDD8539E811E4A3E2CCEF48565980 LEGID = CC65CE04-39E811E4-87DFD7D1-64B198F2 - [INBOUND] DURATION (msecs) = 25610 - DIALOG TERMINATED. Reason: Q.850;cause=16
Line 3768: 3083690: 10.180.245.43: Sep 12 2014 12:21:11.293 -0700: %CVP_8_5_SIP-7-CALL: {Thrd=DIALOG_CALLBACK.6} Sending BUS MSG:>>HEADERS: (JMSType)=MsgBus:CALL_STATE_EVENT (JMSDestination)=Topic(CVP.SIP.CC.EVENT) (JMSTimestamp)=1410549671293 >>BODY: callguid=CBCCDD8539E811E4A3E2CCEF48565980 RouterCallKey=6472 RouterCallKeySent=true causecode=1 timezone=America/Los_Angeles RouterCallKeySequenceNumber=0 version=CVP_8_5 labeltype=1 RouterCallKeyDay=151099 calldate=Fri Sep 12 12:21:11 PDT 2014 label=190376 localOffset=-420 eventid=6 calllegid=CC65CE04-39E811E4-87DFD7D1-64B198F2 >>STATE: isTabular=false isWriteable=true cursor=-1
The first Termination message came on the INBOUND leg which is the PSTN. That means, PSTN side disconnected the call first.
Hope this helps.
Abu

My ipone4 screen is black cannot answer when calls come in

The screen went black/blank, I cannot answer it but it allows calls to come in - any suggestions?

Hello Pamd21562,
Thanks for using Apple Support Communities.
Since your iPhone is still on and functioning aside from its screen being black, I recommend you follow the troubleshooting below.
If you see a solid color screen (black, white or blue)
Plug in your device to a power source. If you see the low-battery screen when you plug in, let your device charge for at least 10 minutes (20 minutes for iPad) before using it.
Reset your device while it's plugged in.
If resetting doesn’t fix the issue, restore your device.
If you still see the issue after you restore, contact Apple Support.
Get help with the screen on your iPhone, iPad, or iPod touch - Apple Support
Take care,
Alex H.

UCCX Agent Desktop Auto Answering Calls

Has anyone heard of a situation where CAD is auto answering calls? The users are reporting it sporadically only when they get a off a call and a call is waiting in queue, the call will automatically connect right after they hang up the first call.
Sounds bizarre, I know.
Short of restarting services, i'm not sure where to go with this one. I've had a couple clients report this issue to me. They are running UCCX 9.0 (2) SU1
Thanks.

We've had a similar issue. While the agent is talking, the CAD changes state to "work" i.e. it thinks that the call has been hung up. It then goes to "ready" while the agent is still talking. As a result, when the agent hangs up their call, they are in "ready" state and are given the next call immediately.
You may want to check if this is the case with the agent state.
If the state changes are happening like this, check that the handset is snugly sitting on the cradle, reboot the client PC and have them log off/on the phone.
Be sure also to check the CAD agent logs. I'm about to check ours now to see if they show anything up.

UCCE Agent cannot answer call

Similar Messages

Maybe you are looking for