UCCE Multiline Agent support not working

Hi all,
I enabled multi line support for agents on PG.... Restarted PGs...
And its not working, when agent recieves call on non-acd line, it doesn't go to not-ready...
Any hints?
Thank you
V

I found what was the problem
It didn't catch the change in configuration in PGs, Logs showed said single line for multiline settings...
I found a post from Geoff, where it said to exit_opc... and it worked...
And I checked all phones/lines 2-3 times before I was making a change
But thanx
V

Similar Messages

Service support not working of webcam

i am purchase a laptop envy 6 a weak before but its webcam not working.hp phone support not working properly.when i use phone support they did not pickup the call..please solve my problem as soon as possible.

Sometimes electrical components needs to have all power sources removed and reintroduced to work properly. Try performing a hard reset first, if it doesn't work then we'll move to the next step.
To Perform A Hard Reset
Shut down the computer by going to the Start menu and selecting shut down. (If you have no display, hold the power button down for 5 seconds); (if the computer doesn't power on, move to the next step)
Disconnect the AC Adapter from the notebook.
Remove the battery from the bottom of the notebook. There will be a switch/button to eject the battery.
Wait at least 1 minute with all power sources disconnected.
Re-insert the battery and reconnect the AC Adapter and then attempt to power on the notebook.

Chat support not working on multiple browsers

Have been trying to start chat sessions throughout the week with no luck. It's been during chat hours, and have tried multiple browsers.
Such long wait times with phone support that I hang up before an answer.
Any response would be greatly appreciated. It's a shame to have such horrible support / customer service with a paid membership.

It's not working for me either.

Snow Leopard with Exchange support not working

I tried out the new mail with exchange support (I use Microsoft Outlook at work). I tried to set up my account the same way with my iPhone, but it did not work . . . (I can get my work email to my iphone with the same account set up).
I know I'm not giving a lot of information here, but any ideas what the problem might be?
Thanks!
Lindsay

I just posted this elsewhere:
For those of you that have iPhones that have been successfully using exchange for any period of time - don't expect mail.app to work for you!. Although there are improvements in exchange support, SL still does not support RPC over HTTP / (S). This is used quite widely by many companies still using Exchange server 2003, and provides seamless "no-vpn-required" access to the exchange server using an outlook web access server. I was, as most were, waiting for full exchange integration (Mail/iCal/Address etc). Nope. My question is this: if it was so simple to get this into the iPhone (and it works perfect).. why is this not in mail.app??? Full "out of the box" exchange support is not true at all.

A4j:support not working inside rich:datatable

One of my columns in rich:datatable is h:selectboolencheckbox which i want to select we user clicks a row
but a4j:support is not working.
                <rich:dataTable value="#{ch.fdetails}" var="c" style="width:90%" columns="14">
                       <a4j:support event="onRowClick" action="#{ch.toggle}" reRender="select" ajaxSingle="true">
                        <f:setPropertyActionListener target="#{ch.fd}" value="#{c}" />
                 </a4j:support>
               </rich:dataTable> It doesn't even call action on bean which is toggling the chechkbox.

Hi, I assume you are using <rich:column>
so try to change event to onselect or onchange and if your action is method call so change
action="#{ch.toggle}"to
action="#{ch.toggle()}"

MSi website support not working - poor service!

MSi website support is not working. Everytime I try to contact them using the support tickets I get a garbled message on screen and once you click the OK button it clears your ticket with nothing posted.
It's a very poor way for a company supposed to be a BIG company showing support to its customers.
You can't telephone them, cannot now use the ticket support, and can only HOPE someone from their technical department reads THIS.
I sent them an email about it and I'm just waiting to hear from them.
It makes me want to change to ASUS in future!

Ok I'll try to remain calm as I've just received a warning about "bashing" MSi.
I'll include the screenshot again for your attention. At least the moderators here are reviewing the situation it seems, which, on a large forum, I didn't think would be noticed.
After going through advice of how to update my BIOS with their technical help on the website I flashed my MSi Z68A-GD65 (B3) successfully to version 22.8. It was playing up before that on the orginal BIOS, slowing down in Windows, not recognizing various USB devices, and I had a Primary BIOS led flashing which meant it had failed on the mobo so the computer wasn't coming out of 'sleep' very good (I just left it on all the time instead).
22.8 made it seem to be at it's best then I contacted them on which update next; they said P.1. Unlike the previous one which I flashed inside the BIOS using M-flash, this had to be done in DOS which I did.
I saw a brief message which I think said updating should not be done while it is overclocked (I had the OC button on) but other than that it went through and said update was "successful". That was the last message my machine made.
It is now in a constant 'boot loop' which lasts about 10 seconds, not enough time to interrupt or use a boot device, and just cycles switching off to booting then switching off, etc.
I've seen many cases of this and it must be a common problem, as I did everything as instructed and still it went wrong.
After lots of communication MSi UK agreed to inform the service department for a RMA to be sent to me, even though it was out-of-warranty. Then they closed the ticket. I opened a new ticket asking why they closed the ticket and I still had not received any RMA, they told me not to worry the RMA will be coming, then closed that ticket.
After waiting 10 days I tried to use the website form again filling out all the criteria on the form and instead I get this garbled writing with the OK button as I mentioned, which just sends you back to the home page with nothing updated.
So I am really frustrated at this point, unable to phone MSi (they won't talk to you), use the website (in UK) and have had to explain everything through an email correspondence, hence my lack of patience on this forum.
For years I put my faith in MSi products, I have a Nvidia graphics card also, and they are the market leader with the best looking designs and most powerful components. But they should provide better customer support when things go wrong and are failing anyone who resides in the UK with a website service which doesn't work, and closing tickets before the problem has been sorted or the RMA has been sent.
I hope you understand.

Oracle 10g Agent is not working in Windows VISTA

Hi
I have installed Oracle 10g Grid Control in VISTA. But the Agent is not getting started.
the trc in the Agent10 G log directory is
2008-04-19 17:29:45 Thread-532 WARN http: snmehl_connect: connect failed to (HP-PC:3872): No connection could be made because the target machine actively refused it.
(error = 10061)
2008-04-19 17:29:45 Thread-532 ERROR main: nmectla_agentctl: Error connecting to https://HP-PC:3872/emd/main/. Returning status code 1
2008-04-19 18:18:22 Thread-5288 WARN http: snmehl_connect: connect failed to (HP-PC:3872): No connection could be made because the target machine actively refused it.
(error = 10061)
2008-04-19 18:18:22 Thread-5288 ERROR main: nmectla_agentctl: Error connecting to https://HP-PC:3872/emd/main/. Returning status code 1
2008-04-19 18:18:23 Thread-7652 ERROR main: nmectl.c: nmectl_validateTZRegion, agentTZoffset =330,and testTZoffset for GMT:0 do not match
2008-04-19 18:18:24 Thread-7652 ERROR main: nmectl.c: nmectl_validateTZRegion, agentTZoffset =330,and testTZoffset for GMT:0 do not match
2008-04-19 18:18:26 Thread-7272 WARN http: snmehl_connect: connect failed to (HP-PC:3872): No connection could be made because the target machine actively refused it.
(error = 10061)
2008-04-19 18:18:26 Thread-7272 ERROR main: nmectla_agentctl: Error connecting to https://HP-PC:3872/emd/main/. Returning status code 1
2008-04-19 18:20:52 Thread-4872 WARN http: snmehl_connect: connect failed to (HP-PC:3872): No connection could be made because the target machine actively refused it.
(error = 10061)
2008-04-19 18:20:52 Thread-4872 ERROR main: nmectla_agentctl: Error connecting to https://HP-PC:3872/emd/main/. Returning status code 1
2008-04-19 18:20:53 Thread-4344 ERROR main: nmectl.c: nmectl_validateTZRegion, agentTZoffset =330,and testTZoffset for GMT:0 do not match
2008-04-19 18:20:54 Thread-4344 ERROR main: nmectl.c: nmectl_validateTZRegion, agentTZoffset =330,and testTZoffset for GMT:0 do not match
2008-04-19 18:20:55 Thread-5604 WARN http: snmehl_connect: connect failed to (HP-PC:3872): No connection could be made because the target machine actively refused it.
(error = 10061)
2008-04-19 18:20:55 Thread-5604 ERROR main: nmectla_agentctl: Error connecting to https://HP-PC:3872/emd/main/. Returning status code 1

This pretty much says it all:
No connection could be made because the target machine actively refused it.What version of Vista?
What version of the agent? ... 10g is not a version number it is a marketing label
Did you check to see if the agent is compatible with your operating system?
My recommendation would be to get a real operating system: Either Oracle Linux or XP.

PSE7 BACKUP/SYNC AGENT does not work.

Under the Preferences box , the Backup/Sync Agent does not open. I can't alter or change anything. When I sign in , my sign in and password are both accepted ,however where the Welcome is on top, it used to say Welcome, with my first name. It does not do this anymore. When I try to upload my pics to Photoshop.com it states I am not logged in. No one at Adobe has been able to help after 4 months .

Hi,
Can you please contact me on [email protected]
I would like to suggest few things offline...

No outbound email, Can't change Agent, Alternate not working

Our server with our primary MTA has failed and Groupwise is still trying to send outbound Internet emails to it. POA is on another server. Despite there being an Alternate Internet agent defined no outgoing emails are being sent. The Alternate GWIA is alive and apparently working fine.
I cannot select the Internet Agent in the Domain as the option is greyed out (as is the Override check box). I have changed it in the System properties but the Domain shows the old, dead GWIA. I was already using Message Transfer Ports so Tid 3187743 does not apply.
The MTA log shows it trying to connect to the dead MTA.
I have restarted groupwise a lot and rebooted the server.

NickHoare,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

Illustrator CC 17.1.0 64 bit Type - Right to Left language support support not working

Update:
See below
Hello,
I have followed the directions here:
http://helpx.adobe.com/illustrator/using/arabic-hebrew.html
Went to Type tool> paragraph panel> options switched to Middle Eastern ... Single line composer, but the P> <P (RTL LTR) selector did not appear.
Tried to reset the tool a few times, to restart Illustraor, with no luck.
What can be done?
Win 8.1 64 bit, Adobe CC Illustrator 17.1.0 64 bit
Thank You
Gidon
Update:
Just taked on the phone with Adobe support,
They told me to go to preferences Hyphenation, change language from English to Hebrew.
Then UNINSTALL Ilustrator and REINSTALL it.
Sounds strange to me.
Has anyone encountered this kind of problem??
Thanks
Gidon

I think you have to have the Middle East or North African versions. From the link:
"New and improved features for working in Arabic and Hebrew are available in the Middle East and North African edition of this software."

Canon EOS Kiss Digital X Support Not Working

I have just installed the RAW Support update that is meant to provide support for the 400D/XTi/Kiss Digital X. I bought my camera in Japan, so I have the Kiss Digital X.
I STILL cannot use Raw files in Aperture or Preview. Does this work for anyone else?

In case anyone else feels like confirming this issue,
or even better someone from Apple is reading this and
needs a test file to diagnose the issue I have
uploaded a sample RAW file from my Kiss Digital X
here: http://www.robbieduncan.net/rawtest.CR2 Note
that this file is 12.4Mb!
After downloading "Digital Camera RAW Support Update (PPC)"
I downloaded your file rawtest.CR2, stripped off the .TXT extension - used .CR2 and it was:
Not recognized in Preview or iPhoto,
But it worked ok in the finder with a preview thumbnail (very dark) and in Graphic Converter X 5.9, with the following EXIF Data: (after Converting to JPEG) .... see that your Camera model is recognized! .. very strange, maybe a corrupted file??
File Name rawtest.jpg
Document Type JPEG Image
File Size 9247786 bytes
Color Model RGB
Depth 8
DPI Height 72
DPI Width 72
Orientation 1
Pixel Height 2622
Pixel Width 3948
Exif Properties
Aperture Value 4
Color Space 1
Custom Rendered 0
Date Time Digitized 2006:10:29 16:35:30
Date Time Original 2006:10:29 16:35:30
Exif Version 2.2.1
Exposure Bias Value 2
Exposure Mode 0
Exposure Program 4
Exposure Time 0.00625
Flash 16
FlashPix Version 1.0
FNumber 4
Focal Length 118
Focal Plane Resolution Unit 2
Focal Plane X Resolution 4433.295
Focal Plane Y Resolution 4453.608
ISO Speed Ratings 1600
Metering Mode 5
Pixel X Dimension 3948
Pixel Y Dimension 2622
Scene Capture Type 0
Shutter Speed Value 7.32193
White Balance 0
JFIF Properties
Density Unit 1
IsProgressive 1
JFIF Version 1.1
X Density 72
Y Density 72
TIFF Properties
Date Time 2006:10:29 16:35:30
Make Canon
Model Canon EOS Kiss Digital X
Orientation 1
Resolution Unit 2
X Resolution 72
Y Resolution 72

Surface Pro3 Logging Agent does not work

Hey Guys!
I am developing mdm for surface pro3. I want to get the client mdmagent log for my mdm debugging. By following the steps mentioned in the section Agent Logging of Win8.1 Enterprise Device Management Protocol, I add the content which is
"EnableSyncmlLogging"=dword:00000001 to the registry. But the device hasn't generated the
mdmagent.pdb, mdmappprov.pdb and
mdmsettingsprov.pdb. I beg to know why and thanks for your answers.

Those files are not the output, they are the trace providers that you need to select in the
traceview.exe tool.
Eric Fleck, Windows Store and Windows Phone Developer Support. If you would like to provide feedback or suggestions for future improvements to the Windows Phone SDK please go to http://wpdev.uservoice.com/ where you can post your suggestions and/or cast
your votes for existing suggestions.

Platform agent does not working after installing SMS 1.5

Good time of the day to everybody,
I'm using SunMC 3.6 to monitor SFE25K. After upgrading SMS version to 1.5 platform agent on SC crashes after few minutes of running. In the log files I see only "[ID 603404 kern.notice] NOTICE: core_log: esd[23533] core rlimit is zero, core not dumped" in the messages file. At the same time ConfigReader works fine.
I can't find any patches or documents related to this problem at sunsolve. Does anybody knows how to make the agent to work? 'es-setup -F' does not helps.
thanks

In addition, process crashes with following:
Incurred fault #5, FLTACCESS %pc = 0xFF147648
siginfo: SIGBUS BUS_ADRALN addr=0x6E65742F
Received signal #10, SIGBUS [default]
siginfo: SIGBUS BUS_ADRALN addr=0x6E65742F

OpenGL support not working

OpenGL support does not seem to be working on PhotoshopCC. The HUD color picker does not appear and when I try to rotate the canvas, a message pops up that says the rewuest could not be completed because it only works with OpenGL enabled windows.
I have two NVIDIA Quadro K600 cards (with up to date drivers), a Cintiq monitor and a new Dell workstation. I'm using the trial version of Photoshop CC. (I had to replace my computer recently because the old one died, and rather than reinstalling CS4 I decided to try CC and see how I liked it)
My machine is a powerful graphics computer, so it ought to be able to handle OpenGL. Under Preferences/Performance I do have "Use Graphics Processor" checked, but it does not help.

Adobe Photoshop Version: 14.0 (14.0 20130423.r.221 2013/04/23:23:00:00) x64
Operating System: Windows 7 64-bit
Version: 6.1 Service Pack 1
System architecture: Intel CPU Family:6, Model:13, Stepping:7 with MMX, SSE Integer, SSE FP, SSE2, SSE3, SSE4.1, SSE4.2
Physical processor count: 4
Processor speed: 2992 MHz
Built-in memory: 4022 MB
Free memory: 1932 MB
Memory available to Photoshop: 3364 MB
Memory used by Photoshop: 60 %
Image tile size: 1024K
Image cache levels: 4
OpenGL Drawing: Enabled.
OpenGL Drawing Mode: Advanced
OpenGL Allow Normal Mode: True.
OpenGL Allow Advanced Mode: True.
OpenGL Allow Old GPUs: Not Detected.
OpenCL Version: 1.1 CUDA 4.2.1
OpenGL Version: 3.0
Video Rect Texture Size: 16384
OpenGL Memory: 1024 MB
Video Card Vendor: NVIDIA Corporation
Video Card Renderer: Quadro K600/PCIe/SSE2
Display: 2
Display Bounds: top=-30, left=-1920, bottom=1050, right=0
Display: 1
Display Bounds: top=0, left=0, bottom=1050, right=1680
Video Card Number: 2
Video Card: NVIDIA Quadro K600
Driver Version: 9.18.13.1090
Driver Date: 20121229000000.000000-000
Video Card Driver: nvd3dumx.dll,nvwgf2umx.dll,nvwgf2umx.dll,nvd3dum,nvwgf2um,nvwgf2um
Video Mode: 1680 x 1050 x 4294967296 colors
Video Card Caption: NVIDIA Quadro K600
Video Card Memory: 1024 MB
Video Card Number: 1
Video Card: NVIDIA Quadro K600
Driver Version: 9.18.13.1090
Driver Date: 20121229000000.000000-000
Video Card Driver: nvd3dumx.dll,nvwgf2umx.dll,nvwgf2umx.dll,nvd3dum,nvwgf2um,nvwgf2um
Video Mode: 1920 x 1080 x 4294967296 colors
Video Card Caption: NVIDIA Quadro K600
Video Card Memory: 1024 MB
Serial number: Tryout Version
Application folder: C:\Program Files\Adobe\Adobe Photoshop CC (64 Bit)\
Temporary file path: C:\Users\kitfox\AppData\Local\Temp\
Photoshop scratch has async I/O enabled
Scratch volume(s):
C:\, 930.2G, 785.0G free
Required Plug-ins folder: C:\Program Files\Adobe\Adobe Photoshop CC (64 Bit)\Required\
Primary Plug-ins folder: C:\Program Files\Adobe\Adobe Photoshop CC (64 Bit)\Plug-ins\

HP Total Care, HP Help and Support not working.

When I try to use HP Help and Support, I click on almost any type of scan or help it launches the Note Pad which is filled with multiple symbols. I'm using Vista 32 on an HP Notebook.

I'm also having the same problem with my HP Notebook running on Vista x64. When I use HP Help and Support it launches Notepad filled with characters. The same thing happens when I launch Activation Assistant for Microsoft Office 2007. The Notepad opens and display some characters. I reinstalled the HP Help and Support from my Recovery Manager but did not solve the problem. I downloaded the utility from HP support site but my problem became worse. The HP Help and Support Customization disappeared. When I select some of the links on the Vista Help and Support (now without the HP customization), the Notepad still opens with the characters. By the way, when I reinstall the HP Help and Support during the process the Notepad also appears and display characters and the installation does not proceed until I close the Notepad.
I've searched for solution on several forums but found nothing.
Any help to resolve this problem would be appreciated. Thanks.

UCCE Multiline Agent support not working

Similar Messages

Maybe you are looking for