UCCX Agent can`t loggin

My UCCX is 8.5 su3 ,CME is 8.5.When the IP phone agent loggin ,the screen display "The extension you entered is not associated with this agent ID. Verify the extension and try again"
The CME config in the Attach file.
I have creat agent on UCCX server.
I have read the Cisco Unified CallManager Express System Administrator Guide,Cisco Unified Contact Center Express Solution Reference Network Design Guide.But I can't find out how to handle this problem.

Hi,
I hope you are using the compatible CME IOS image,
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_compatibility/matrix/crscomtx.pdf
->Details of CME/IOS version mapping can be found at
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/33matrix.htm
->Only SCCP Phones are supported as Agent Phones with Unified CME. Refer to "Cisco Unified IP Phone Support" section from the respective Cisco Unified CME
Supported Firmware, Platforms, Memory, and Voice Products web page. For example, for Cisco Unified CME 7.1, go to: http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/cme71spc.htm, and scroll down to view the "Cisco Unified IP Phone Support" table.
c. Cisco IP Phones 6911, 6921, 6941, 6945, 6961, 8961, 9951, 9971 are not supported as Agent Phones with Unified CME
If everything is ok and you are still facing the issue, than I would suggest you to appraoch TAC for further help.
Thanks,
Anand

Similar Messages

UCCX 10.5 - newly created agents can't login to CAD

Hello,
After upgrading UCM 8.6 to 10.5 and UCCX 8.5 to 10.5 I can't add new agents. I have installed second UCCX and reused CTI and RMCM users, registered CIPC, created end-user, configured IPCC extension and set CIPC in controlled devices on end user and rmcm user. DN is not a shared line. When I try to login to CAD it asks to associate the phone with RM JTAPI provider user. Agents created before upgrade works fine. I see the following traces:
120643: Aug 08 16:46:18.387 MSK %MIVR-ICD_CTI-7-UNK:ClientConnMgr: Processing msg on socket:Socket[addr=10.1.9.66,port=62888,localport=12028] Msg is {length=71 type=SET_AGENT_STATE_REQ,invokeId=47,agentState=LOGIN,eventReasonCode=1,forcedFlag=False,agentID=m.denisov2,agentDN=1900,agentPwd=***** }
120644: Aug 08 16:46:18.388 MSK %MIVR-ICD_CTI-7-UNK:This connection is using encrypted passwords for agent login message
120645: Aug 08 16:46:18.401 MSK %MIVR-SS_RM-7-UNK:Processing msg: CTISetAgentStateReqMsg (Rsrc:m.denisov2 InvokeID:47 State:LOGIN Forced:False)
120646: Aug 08 16:46:18.401 MSK %MIVR-SS_RM-7-UNK:Agent m.denisov2 is outbound capable.)
120647: Aug 08 16:46:18.401 MSK %MIVR-SS_RM-7-UNK:Rsrc: m.denisov2 Contacts:
120648: Aug 08 16:46:18.401 MSK %MIVR-SS_RM-7-UNK:Rsrc: m.denisov2 PrevState: UNKNOWN PrevStateSet:false
120649: Aug 08 16:46:18.401 MSK %MIVR-SS_RM-7-UNK:Rsrcs in ARL of ESD RU-MSK-DIRECT_SALES:
120650: Aug 08 16:46:18.697 MSK %MIVR-SS_RM-7-UNK:Trying to authenticate agent m.denisov2
120651: Aug 08 16:46:18.880 MSK %MIVR-SS_RM-7-UNK:Processing msg: class com.cisco.wf.subsystems.rmcm.msgs.UserAuthJobResponse Rsrc:m.denisov2
120652: Aug 08 16:46:18.927 MSK %MIVR-SS_RM-7-UNK:Rsrc: m.denisov2 New State:LOGOFF Old State:LOGOFF Reason code:1
120653: Aug 08 16:46:18.927 MSK %MIVR-SS_RM-7-UNK: The mapping SEP902B34750ED4-m.denisov2 has been added
120654: Aug 08 16:46:18.927 MSK %MIVR-SS_RM-7-UNK:Terminal SEP902B34750ED4 IPv6 Address is NULL
120655: Aug 08 16:46:18.927 MSK %MIVR-SS_RM-3-LOGIN_FAILED:Login of resource failed: Module Name=RM component,The description of a message sent from/to the RM=CTISetAgentStateReqMsg (Rsrc:m.denisov2 InvokeID:47 State:LOGIN Forced:False),A specific description for a trace=problems in JTAPI or CM
120656: Aug 08 16:46:18.927 MSK %MIVR-SS_RM-7-UNK:Posting msg CONTROL_FAILURE_CONF Socket:Socket[addr=10.1.9.66,port=62888,localport=12028] invokeID:47 failureCode:CF_GENERIC_UNSPECIFIED errorCode:88001 text:Unable to login agent due to problems in JTAPI or CM in CTI Server's message queue
120657: Aug 08 16:46:18.927 MSK %MIVR-ICD_CTI-7-UNK:OutboundMsgProcessor: got message: { CONTROL_FAILURE_CONF }
120658: Aug 08 16:46:18.928 MSK %MIVR-ICD_CTI-7-UNK:OutboundMessageprocessor : sending msg : { length=-1 type=CONTROL_FAILURE_CONF,invokeId=47,failureCode=CF_GENERIC_UNSPECIFIED,errorCode=88001, text=Unable to login agent due to problems in JTAPI or CM to socket: Socket[addr=10.1.9.66,port=62888,localport=12028] }
120659: Aug 08 16:46:18.928 MSK %MIVR-ICD_CTI-7-UNK:MsgHandler : Sent : { CONTROL_FAILURE_CONF to Socket[addr=10.1.9.66,port=62888,localport=12028] }
I have tried to disassociate and associate the phone with rmcm user and even rebooted UCCX, how can i troubleshoot this problem furher?
I use IPv4 only, what means line 120654, is it normal?
Regards,
Maxim

I have installed second UCCX and reused CTI and RMCM users,
It sounds like the upgrade is irrelevant here, and what we're really troubleshooting is your second UCCX installation which is using the same accounts as your first UCCX installation.
Of course, I've been around long enough to know that communication breakdowns are common, and you may have not meant that.
For example, maybe what you meant was, you added an HA node? But if not, and you really installed a new instance while reusing the existing credentials, I would suggest creating new app users for your new UCCX and not sharing them.
PS It's very hard for me to read your log snippet with the black background. Could you edit your post and remove the formatting please? Thanks.

Can't move UCCX agent to another extension

I have a UCCX 7 system integrated with UCM 7.1.3. I'm trying to move a UCCX agent from one extension to another extension. Both of the phones are associated with the RM application user, and with the agent's end user entry. I originally had the agent configured for extension 3606 and they were able to log into Cisco Agent Desktop. I changed the IPCC extension value in their end user entry to extension 3607, and then had the agent try to log in at that station. CAD gave the error that the extension was not associated with their userid.
Do I need to restart some service to get this change to take effect?
Thanks for any help,
Robert Luechtefeld

try to restart cisco ldap synic service from windows services
good luck
if helpful Rate

UCCX Agent Configuration

Hi everyone,
I'm having some concerns about the design I should put in place for my lab to reflect the best solution to implement :
Our call center needs are basics : all their phones are anonymous and every agent can connect to any phone using its agent id (that is the goal and also the current solution with basic Alcatel ACD TDM).
So, should I create standard anonymous phone template for all phone and then put a single button login IPPA onto each phone
or
Should I use EM to have my user logged a first time on EM, and then have the single button login for IPPA within EM profile.
I check Cisco UCCX design guide and EM is not mendatory, i'm just wondering wether it's a better choice not to use EM : it reduce the delai and actions on the phone before loggin in IPPA.
Thanks for your feedbacks on that design point.
Best regards,

Hi,
I'm going to test the same scenario, in my test when the user logged off on EM the Agent state is in "not ready" and remain logged in so if I try to login the same EM user and Agent, I receive an alert and the operation is not user friendly.
I have to force the logoff of the previous agent, force the logoff again and login the agent.
There is a solution for terminate a session or force a logoff of the agent after a perid of time ?
I've tried with workflow management but it doesn't work.
Thanks
Franco

UCCX Agent with Unified Mobility

Hi all,
We have UCCX 8.5 and CUCM 8.6
Maybe somebody knows.
Can we make next:
Incomnig call to UCCX ---> UCCX Script--->CAD and Agent IP Phone
But we woud like configure Unified Mobility feature and use this feature with UCCX agents phone.
There is moment when agent leavs his workplace, and we want forward incoming calls UCCX to agents mobile phone.
I would be very grateful for the helpful advice.
Perhaps there are other solutions

I have just configured Mobile Connect on a ACD line and tested it and it seems to work fine The Agent phone rings then if not answered the mobile rings, the call is answered. Call is seen on the Agent phone aswell and in CAD and the call gets included in the Agent call stats.
I know it's not supported, but what issues should I expect to see?
Thanks,
Stuart

Interesting Client Concern: UCCX Agent Tricks

I had a client ask us to compile a list of tricks UCCX agents use to get around meeting job requirements. Other than not transferring calls to post-call surveys I couldn't think of any. So does anyone know of things agents can do with UCCX that may be considered tricks/work-arounds to "beat the system"?
Thanks,
Brian

Hi,
well, Tanner has a point, it must be solved processwise.
The company I used to work for had a customer with a large UCCE contact center and they asked for a report that would show this kind of suspicious activity. UCCE has actually a way to mark these calls, unfortunately, as far as I know, there is no such thing in UCCX. The rule was simple: you can be caught only once doing that.
G.

How many Management agents can you have running simultaneously on a host?

Hi all,
I've scoured the Oracle documentation and not been able to find a definitive answer to this question, how many Oracle management agents can you have on a single managed host target? Can you for example run an 11g agent and a 12c agent simultaneously (whilst migrating to 12c without upgrading the present OEM instance) If so can you run two 12c agents, each pointing to a different OMS? I’ve seen examples of an agent for each database instance on a host managed target, so a host with three Oracle database instances has three Oracle Management agents all pointing to the same OMS with each agent is monitoring just one of the database instances. There must be resource considerations here for memory, cpu and network traffic etc? I’ve always understood it to be one Oracle Management Agent per managed host
Thanks

I don't think there's any data on impact or performance since it's not a recommended configuration. If you have host/configuration monitoring enabled on both agents, they will be running the same queries/scripts against the host/inventory, etc. so they will likely have contention at some point. If you monitor the same databases, you will definitely see contention and increased overhead as there will be multiple agents running the same queries. You might also see problems w/ any of the server generated alerts (tablespace, etc) if you change thresholds as the agents send that to the database, and then the database will be out of sync with the other agents.
What exactly is the goal for having multiple agents? Is it short term or long term?

UCCX Agent Desktop v.7 taking over Windows active session when phone rings

I'm trying to figure out how (if possible) for the Cisco UCCX Agent Desktop application from taking over a users Windows session every time the phone rings. This is very annoying and takes the end user out of what ever application they are currently in whenever their phone rings. Does anyone know how to change this?

Hi Eric,
Maybe this is better
Miscellaneous tab options.
Option Description
Window Behavior Specify how you want the Agent Desktop window to
behave:
• Normal. The window appears when calls are
present and minimizes when idle.
• Keep Open. The window is always visible, but may
be hidden by other open applications.
• Always on Top. The window is always visible and on
top of other open applications.
• Stealth. The window appears as an icon in the
system tray.
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/cad_enterprise/cadenterprise7_0/user/guide/cda700ug.pdf
Cheers!
Rob

SQL Server Agent can't start

Hi Expert,
I have a problem when using SQL Server 2005.
I also use Windows Server 2008
My SQL Server Agent can't start.
When I try to start, I have message "The SQL Server Agent (MSSQLSERVER) service on Local Computer started and then stopped (object explorer).
Why does this problem happen?
Thanks
Regards,
Vicky Oktavianus

> 2010-08-16 15:28:21 - ! [241] Startup error: Unable to initialize error reporting system (reason: The EventLog service has not been started)
> 2010-08-16 15:28:21 - ? [098] SQLServerAgent terminated (normally)
You seem to have an issue with your machine, I suggest you check further up in the event log for problems concerning the event log.
Uploading files here is not possible, open an OSS call (component BC-DB-MSS) and ask the support for help, there you can upload the file.
Markus

10gR1 OEM can not verify Solaris 10 host. 10gR2 agent can upload though

Got following error when tried to verify Solaris 10 host.
I have 10gR1 (1.0.3) fresh installation without patch on server 1. Recently I installed 10g R2 agent on a Solaris 10 server 2. The agent can upload data back to the OMS without problem. But after I enter server 2 host credential to verify host connection I got the following error in emoms.log on Sever 1.
"2006-05-31 17:16:49,704 [EMUI_17_05_35_/console/pref/setCredentials$targetType=host] ERROR creds.SetPrefCreds testCreds.1281 - SetPrefCreds.testCreds(): CredsException: Connection to host bcrcxfwwd7p.something.com as user xxxx failed: IOException in sending Request :: Connection timed out"
I can use Secure shell in Solaris to connect to server2 as xxxx directly & do my work.
But somehow I can not verify the host connection from within OEM.
I don't have any problem to use OEM to manage 9 other Solaris 9 hosts and 10g databases. Is Solaris 10 specific problem?
Any suggestions are welcome
Mike

Hang on, are you using a 10.1 oms with a 10.2 agent reporting to it?
If so, thats an unsupported configuration.
Bazza

Dropped/recreated SQL jobs and now SQL Agent can't run b/c old job_id is still being referenced by the Agent.

I've seen a common issue in several of our production environments where after we upgrade our software the SQL Agent can't run some jobs that were recreated as part of the process because they're referencing the old job_id (in msdb.dbo.sysjobs) that no longer
exists. I can fix it easily enough by restarting the agent as this will flush whatever cache is being used by the Agent but I'd like a less invasive way to do this, if possible.
Is there any way to flush the cache used by the SQL Agent to store job_ids without having to restart it? Thanks.

You may try this , and this solves this issue.. I hope if you do this then you no need to restart the agent...
DECLARE @jobId binary(16)
SELECT @jobId = job_id FROM msdb.dbo.sysjobs WHERE (name = N'Name of Your Job')
IF (@jobId IS NOT NULL)
BEGIN
EXEC msdb.dbo.sp_delete_job @jobId
END
DECLARE @ReturnCode int
EXEC @ReturnCode = msdb.dbo.sp_add_job @job_name=N'Name of Your Job'
Raju Rasagounder Sr MSSQL DBA

UCCX Agent ready state softkey

I was under the understanding that UCCX agents could also sign into the ready state through they're assigned phones ? So far in my reading of documents and such I have yet to see any bit of information for setting up agents without CAD. In many of our situations we would like the agents just to be able to sign into the phone adding them to the rotation for incoming calls.
Does anyone know if this is possible and if so is there a reference in some document outlining it ?
Thank you.

Are you looking to log in agents without using the agent desktop? Check out IPPA (IP Phone Agent). This is a IP Phone service that you assign to the agent phone in call manager.
Set up the agent as normal, then add this service to the phone in call manager:
http://x.x.x.x:6293/ipphone/jsp/sciphonexml/IPAgentInitial.jsp
where x.x.x.x is the ip of your UCCX server.
See page 128 of this doc... http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_8_5/installation/guide/cad85ccxig-cm.pdf
Brian
Please rate helpful posts

Install agent fail (Agent host must be registered before an agent can be installed or upgraded.)

I got the following error with trying to install agent
# java -jar agent.jar -d /u01/avagent/
Agent host is not registered.
Agent host must be registered before an agent can be installed or upgraded. Agent deployment failed.
database firewall ip address is 10.0.0.10 (for management) and 192.168.0.10 (for traffic source)
auditvault server ip address is 10.0.0.11 (for management)
I have 2 IP address on my DB 10.0.0.9 and 192.168.0.9
when i register host with ip 192.168.0.9 i will get the error
but if i register host with ip 10.0.0.9 installation is fine with no error
i want to monitor audit traffic on 192.168.0.9 interface which is for client to access so i need to register host with ip 192.168.0.9

hi Stefan,
this is expected behaviour, or at least it's better to say : in a multi homed system the choice of the network path that is used is determined by the underlying tcp network,
it doesn matter which path the sqlnet connection from agent to AV server takes as long as it is able to connect. Your statement about 'monitor audit traffic on 192.168.0.9'
does not make sense, the agent / collection framework is the part that fetches audit records from secured targets and has nothing to do with monitoring network traffic since
that part of the functionality is done by the firewall component. Anyway if you want to change the nework path you need to use 'route' and force it,
greetings,
Harm ten Napel

Can not loggin the iMessage and FaceTime in Mac pro

I can not loggin the iMessage and FaceTime in my Mac pro, but I can use both of them on my Iphone and iPad.Is there anybody who can help me to solve this problem?

Howdy Anfromhochiminhcity,
Thanks for using the Apple Support Communities.
If you're unable to activate both iMessage and FaceTime on your iPhone, then follow the steps in the article linked to below.
If you get an error when trying to activate iMessage or FaceTime - Apple Support
Take care,
Alex H.

Scheduler agent can't submit state ORA-06502:

hi all
scheduler agent can't submit state
getting below error on agent side in $ORACLE_HOME/data/agent.log
2012.08.31 03:32:56 MSD Job terminated successfully. Duration: 14.89 seconds
2012.08.31 03:32:56 MSD Database Error on Submit: Job Run Completion Failed!
2012.08.31 03:32:56 MSD Database Error on Submit: Error: ORA-06502: PL/SQL: numeric or value error: character string buffer too small
wtf ?
Edited by: djeday84 on Aug 31, 2012 10:34 AM
ps: db oel 5.8 psu 11.2.0.3.2
client win 2003 ( scheduler agent 11.2.0.3 )

Hi Sridher,
is there any question attached to your posting?
How long is the answer of your web service? (in bytes)
brgds,
Peter
Blog: http://www.oracle-and-apex.com
ApexLib: http://apexlib.oracleapex.info
BuilderPlugin: http://builderplugin.oracleapex.info
Work: http://www.click-click.at

UCCX Agent can`t loggin

Similar Messages

Maybe you are looking for