UCCX Outbound configuring

Good day!
I try configure outbound campain on UCCX
8.5.1.11003-32
UCCX call customer but does not pass RTP. We use SIP trunk beetwen VG and CUCM.
When we call to RP from internal phone we can hear IVR. Outbound Campign use same application.
What could be the cause?
Other call through this VG and SIP trunk work fine.
I have attached debug ccsip from VG and shr run.

I had the same issue.
It seems that it's related to the CPA support of your SIP Gateway.

Similar Messages

UCCX Outbound Option - What needs to be configured besides UCCX Outbound config

I'm trying to setup Outbound Option for UCCX 10.0. Unfortunately my knowledge in VoiceGateways isn't really deep. What I'm wondering is:
1) On progressive mode: Do I need to add some components (e.g. VGW) to CUCM first or is UCCX talking directly to the VGW?
2) On direct preview mode: Even if I havn't configured CUCM (if needed) and VGW properly, an outbound call should be suggested to the agent anyway before dialing, is this correct (if UCCX Outbound Option is configured well of course)?
Thanks for every response
Elias

btw: we're using finesse, not CAD

UCCX Outbound Question

Hi All,
I am trying to implement and test outbound option in UCCX. Have few queries regarding that.
we make only CUCM initiated calls to UCCX and dont have a PSTN connection.
1. How to configure UCCX outbound in this case.
2. How to use Phone in same CUCM as customer and Agent.
if possible kindly guide me how to implement it.
With Regards,
Raja Raman

Only if you modify the report to add an additional filter via the stored procedure or Crystal. The general concept of custom reports is somewhat explained in the Historical Reporting Administrator and Developer Guide. It doesn't hold your and through it though; I suggest finding yourself a DBA or Crystal Reporting resource before attempting this.

Import Contacts in UCCX Outbound

Hi,
Whether any mechanism to schedule to read the contacts to be imported for UCCX Outbound instead of importing the contacts list each time manually.
Please help

The provisioning API introduced with 9.0 is how you'll do it. I don't recall whether contact managment is in the 9.0 revision of the API or is being added in 10 though.
https://developer.cisco.com/site/tech/communication-collaboration/contact-center/uccxapi/overview/
Please remember to rate helpful responses and identify helpful or correct answers.

UCCX Outbound Campaign(Preview) Reports

Hi All.
I am configuring outbound(preview) campaigns on UCCX 8.5SU3. Once the campain is done, is there any defult report in which I can see the status of each contact of the campaign such as successful, not dialed yet, invalid number etc?
Many thanks in advance!
Dhammike.

Hi
I'm afraid not - it should be feasible to create a custom report for this purpose though.
Aaron

Mark call as callback in Cisco UCCX outbound

Hi,
I am using Cisco UCCX 10.0. I configured outbound system in uccx and calls are offering to agents.
Anybody please help how a call can be marked as callback in uccx.
Also whether i can update the result of the call; for example: I am running a campaign for credit card. Whether i can update any where that what each customer responded.
Please help

Anybody please help how a call can be marked as callback in uccx.
The agent has a Callback button in CAD while the call is connected to setup the callback. The callback window defined on the campaign will decide how much slack on either side of the desired callback time system will offer that preview call to an agent. Also, the missed call behavior defines what happens if the subsystem cannot find an agent within the window.
Also whether i can update the result of the call
The call result is set to Voice (i.e. customer responded) by default unless an agent Reclassifies the call. Again, this is a button in CAD. The Admin Guide defines what will happen for all of the other result states.
Please remember to rate helpful responses and identify helpful or correct answers.

JMS Outbound Configuration Errors

I'm conducting some tests on JMS Outbound queues with a CEP server. After following the Developer's Guide manual for setting up a JMS Outbound Queue on a CEP server, I'm receiving the following errors on startup:
*<Oct 6, 2010 4:20:12 PM EDT> <Error> <Deployment> <BEA-2045010> <The application context "XMPPMessageEPN" could not be started: org.springframework.beans.FatalBeanException: Error in context lifecycle initialization; nested exception is java.lang.Exception: Error initializing JMS connection: javax.naming.CommunicationException [Root exception is java.net.ConnectException: t3://localhost:7001: Destination unreachable; nested exception is: java.net.ConnectException: Connection refused; No available router to destination] javax.naming.CommunicationException [Root exception is java.net.ConnectException: t3://localhost:7001: Destination unreachable; nested exception is: java.net.ConnectException: Connection refused; No available router to destination]*
I assumed this was all I needed to do. Are there some settings missing for configuring a JMS Outbound Queue that are not in the documentation?
Thanks -- Jim L.
Spring File:
<?xml version="1.0" encoding="UTF-8"?>
<beans xmlns="http://www.springframework.org/schema/beans"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:osgi="http://www.springframework.org/schema/osgi"
xmlns:wlevs="http://www.bea.com/ns/wlevs/spring"
xsi:schemaLocation="
http://www.springframework.org/schema/beans
http://www.springframework.org/schema/beans/spring-beans.xsd
http://www.springframework.org/schema/osgi
http://www.springframework.org/schema/osgi/spring-osgi.xsd
http://www.bea.com/ns/wlevs/spring
http://www.bea.com/ns/wlevs/spring/spring-wlevs-v11_1_1_3.xsd">
<wlevs:event-type-repository>
     <wlevs:event-type type-name="XMPPMessageEvent">
     <wlevs:class>com.enernoc.cep.message.event.XMPPMessageEvent</wlevs:class>
</wlevs:event-type>
</wlevs:event-type-repository>

<wlevs:adapter id="XMPPMessageAdapter" class="com.enernoc.cep.message.adapter.XMPPMessageAdapter" >
<wlevs:instance-property name="hostName" value="talk.enernoc.net"/>
<wlevs:instance-property name="userName" value="oracep"/>
<wlevs:instance-property name="userPwd" value="HKVJqLcX9D4="/>
<wlevs:instance-property name="waitTime" value="15"/>
<wlevs:instance-property name="diagnostics" value="false"/>
</wlevs:adapter>
<wlevs:channel id="XMPPMessageChannel"
event-type="XMPPMessageEvent"
max-threads="3"
max-size="2048">
     <wlevs:listener ref="JMSOutboundXMPP"/>
<wlevs:source ref="XMPPMessageAdapter"/>
</wlevs:channel>
<wlevs:adapter id="JMSOutboundXMPP" provider="jms-outbound"/>
</beans>
Config File:
<?xml version="1.0" encoding="UTF-8"?>
<n1:config xmlns:n1="http://www.bea.com/ns/wlevs/config/application">
<jms-adapter>
<name>JMSOutboundXMPP</name>
<event-type>XMPPMessageEvent</event-type>
<jndi-provider-url>t3://localhost:7001</jndi-provider-url>
<destination-jndi-name>XMPPMessageQueue</destination-jndi-name>
<user>xmppuser</user>
<password>password1</password>
<delivery-mode>nonpersistent</delivery-mode>
</jms-adapter>
</n1:config>

Hi Seth,
I'm trying to create a local JMS queue on the CEP server that others can subscribe to. Why would I need WLS to do this?
--Jim L.

Siebel outbound configuration

Hi All,
Does anyone have an idea about how to configure Siebel to receive calls coming from Outbound dialer. In "CTI Driver for Siebel 7 Reference Guide for Cisco ICM/IPCC Enterprise & Hosted" guide one can find information about how to configure the def file to receive outbound calls, however when this is done siebel client is not able to receive any calls. Is there any additional configuration to be done on Siebel? i suppose outbound buttons should be added on the CTI tool bar.
Please help!

Slightly off-track.
Docs only mention silent monitoring (Unified CM method) possible from CTI-OS supervisor desktop on agent using the connector. How about other supervisory actions from CTI-OS such as barge, intercept, chat, etc
Thanks!
-JT-

UCCX Outbound IVR Port License Requirements

Hi, trying to figure out how many Outbound IVR port licenses are needed.
UCCX dials out, call is answered with a live voice, UCCX transfers to Application Trigger. No agent available, call is queued. At this point 1 Outbound IVR license is used.
Agent becomes available and call is transferred to Agent. At this point is the licensed port returned or is the license consumed until the agent hangs up?
Thanks.

Hi Chris
I dont think the outbound license will be held till agent answers the call.
Here's when outbound licenses will be released:
1. Outbound subsystem calls a contact, live voice is detected, dialer does a refer to agents extension via gateway-sip trunk - CUCM. At this point, outbound port is free and agent takes the call
2. Outbound subsystem calls a contact, live voice is detected, dialer does a refer to IVR trigger. Outbound port is released. Here, the outbound contact is now connected to one of the inbound CTI ports which are associated to the IVR trigger
In summary, as soon as outbound port does a successful SIP Refer transfer, the outbound port is free to be used for next contact.
Regards
Shikhar

CUCM & UCCX Outbound pre-recorded message

Hello,
I have a customer that records all the calls that enters and exits some extensions in CUCM.
By legal request, and since he has a UCCX when a call arrives to those extensions I managed to route the call to UCCX, play a message like "your call will be recorded" and then forwarded to the extension.
Now the problem is that the customer also wants to do this automaticaly on outbound calls, i.e, extension 1111 calls outside number 222222222, he wants that 222222222 when answers listens the message "your call will be recorded" and then when the message ends, the call will be estabilished between 1111 and 222222222.
Is it possible to do that with the equipment that the customer have?
CUCM: 8.6.2.200000-2
UCCX: 8.5.1.11003-32
Thanks in advance...

Awesome Anthoney, thank you very much. I was about to reply after having some issues, though I managed to get it working and the Trigger Application step mixed with two seperate scripts\applications (a triggering script with this step and a script with the actual outbound steps) did the trick.
Thanks again

UCCX Agent Configuration

Hi everyone,
I'm having some concerns about the design I should put in place for my lab to reflect the best solution to implement :
Our call center needs are basics : all their phones are anonymous and every agent can connect to any phone using its agent id (that is the goal and also the current solution with basic Alcatel ACD TDM).
So, should I create standard anonymous phone template for all phone and then put a single button login IPPA onto each phone
or
Should I use EM to have my user logged a first time on EM, and then have the single button login for IPPA within EM profile.
I check Cisco UCCX design guide and EM is not mendatory, i'm just wondering wether it's a better choice not to use EM : it reduce the delai and actions on the phone before loggin in IPPA.
Thanks for your feedbacks on that design point.
Best regards,

Hi,
I'm going to test the same scenario, in my test when the user logged off on EM the Agent state is in "not ready" and remain logged in so if I try to login the same EM user and Agent, I receive an alert and the operation is not user friendly.
I have to force the logoff of the previous agent, force the logoff again and login the agent.
There is a solution for terminate a session or force a logoff of the agent after a perid of time ?
I've tried with workflow management but it doesn't work.
Thanks
Franco

Google Postini outbound configuration with Office 365

Hi all,
My company is currently looking into Office 365 migration. Currently we have Exchaneg 2010 on-premise with Google Postini services for mail security and e-discovery. We are routing all inbound and outbound e-mail trough the Postini-service for archiving
and compliancy reasons.
Inbound is quite easy to set up with the mail connectors in office365, but for outbound Postini requires the IP-adresses of the sending mail servers. Obviously this is constanly changing because of the cloud-based nature of Office 365, but there is no other
way of defining the outbound mailservers for my domain. So my question is as how to cirumvent this or how to define the IP-adresses used by the Office 365/EOP service for sending mail.
Any thoughts on this would be appreciated!

Have you looked up the IP addresses for your <domain>.onmicrosoft.com MX record, using a tool like
http://www.mxtoolbox.com? You are correct that they may change, though. Additionally, I don't know how Postini will handle reinjection to Office 365 - I've read that it's not supported.

UCCX Outbound CCDR Report

On the Agent Outbound CCDR Report there are 18 Call Results.
There are a few that the system can not detect:
5—Customer does not want to be called again.
6—Call connected, but wrong number.
7—Call connected, but reached the wrong person.
8—Customer requests callback. This is not applicable for IVR-based outbound campaigns.
I understand #8, there is a callback button for the agent to schedule the callback.
How does the system know when 5,6, or 7 occurs?

Hi
http://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/cust_contact/contact_center/crs/express_10_5/user/guide/cadx105-agent-desktop-user-guide.pdf
page 45 onwards suggests the agent can select:
'Reclassify' allows selecting 'do not call' (presumably 5)
'Skip-next' then 'wrong number' (i.e. reason 6)
'Skip-next' then 'not home' is presumably 'wrong person' (i.e. wrong person, right number - reason 7)
I've not used preview OB for a while, so may be wrong... but I'd test those outcomes.
Aaron

UCCX : languages configuration error

I have problem during UCCX post installation.
it gives me CAD language update error
please see the attachment file

Hi Marlo,
I think you have clicked on update multiple times . You can re-initiate the setup and it will update the language .
Regards
Ravi

Uccx outbound script & .txt file

Hi all,
I have a file (.txt) to import contacs to outbound. This file have: name, lastname, phone, account. I would like to play a prompt depends of account field.
How to get this field into variable in a script to use this way.
Which is you recomendation?
Regards,

following query returns no output
"select concurrent_program_name, multi_org_category
from fnd_concurrent_programs
where concurrent_program_name = <concurrent short name>"
I have tried to run from the UKHRMS responsibility as well but the report is still giving me the same results i.e. 0 .
pls note that the following SELECT commands do not give any out put ... i.e. after running the concurrent request from the application end.
select rpad(rtrim(name),40)||' '||rpad(nvl(account_number,' '),16)||' '||
substr(to_char(amount,'0009999999.99'),-13)||' '||
rpad(rtrim(bank),35)||' '||lpad(nvl(branch_code1,' '),2)||lpad(nvl(branch_code2,' '),2)||lpad(nvl(branch_code3,' '),2)||' '||
lpad(nvl(branch_code1,' '),2)||lpad(nvl(branch_code2,' '),2)||lpad(nvl(branch_code3,' '),2)||' '||
rpad(nvl(branch,' '),35)||' '||
rpad(rtrim(employee_number),6)||' '||payday
from xx_banks_direct_payments
order by bank, branch_code1,branch_code2,branch_code3, name
select bank, lpad(rtrim(count(employee_number)),4)||
' '||substr(to_char(sum(round(amount,2)),'999,999,999,999.99'),-13)
from xx_banks_direct_payments
group by bank
order by bank
select ' Totals: Number of Employees: ' ||' '||count(employee_number)||' '||' Amount:' ||' '||substr(to_char(sum(round(amount,2)),'999,999,999.99'),-13)
from xx_banks_direct_payments
pls help

UCCX Outbound configuring

Similar Messages

Maybe you are looking for