UCS C series server whether accessible from Linux prompt

Hi UCS Team,
I have UCS c series server.
I am able to check the Fan, power,cooling and equipment and hardware status using the CIMC.
In CIMC I configured the SNMP and check it using MG soft Mib browser tool.
The CIMC query the BIOS for getting the information.
Similarly is there any process to get the BIOS information from the Linux.
Correct me If I am wrong anywhere.
My requirement is to query the UCS C server BIOS information using Linux-SNMP without CIMC.(direct access of BIOS from Linux)
Can I install a Linux supported SNMP client and supported MIBS to query the BIOS level information of UCS using SNMP MG soft Mib browser?

Hi Keny,
I tried to powercycle both servers (c260M2 and C460M2) but still no discovered server and also no logg.
I checked
Rack Server Discovery Policy == immediate
Rack management Connecton Policy == Auto Achnowledged
Chassis/Fex Doscovery Policy == 2 Link and Port-Channel (As I installed 2232PP I moved to Port Channel)
I am running UCSM Version 2.1(1e)
FI 6248 Version 5.0(3)N2(2.11e)
2232PP run on same as FI
I also have a connected 5108 with IOM 2104 running on 2.1(1e) Version.
CIMC Version of C260M2 and C460M2 will be checked tomorrow when my kolleague is in the datacenter.
Server Connection is not really the same like in http://www.cisco.com/en/US/docs/unified_computing/ucs/c-series_integration/ucsm2.1/b_UCSM2-1_C-Integration_chapter_011.html
Because I still have no VIC Card but the connections are the same.
C260 GE LOM1 <-> FEX2 Port 11
C260 GE LOM2 <-> FEX3 Port 11
C260 10 GE LOM1 (PCIE Slot4) <-> FEX2 Port 12
C260 10 GE LOM2 (PCIE Slot4) <-> FEX3 Port 12
GE LOM ist position 13 and 10 GE LOM is position 11 in the techspech of c260
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C260/install/overview.html#wp1243740
C460 GE LOM1 <-> FEX2 Port 10
C460 GE LOM2 <-> FEX3 Port 10
C460 10 GE LOM1 <-> FEX2 Port 9
C460 10 GE LOM2 <-> FEX3 Port 9
GE LOM ist postion 8 and 10 GE LOM ist position 7
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C460/install/overview.html#wp1243740
With C260 I also tried a reboot with disconnected 10 GE Ports, but also no discoverd Server until now.
Regards Alois

Similar Messages

UCS C220 Series server

Hi All,
I have to perform a new installation of UC on UCS servers. This is the first time i am handling the c series servers and I would like to get some clarity on how the Raid is configured.
The servers came with
MegaRAID   9266-8i + Battery Backup for C240 and C220
and each server has four 500Gb hard drives. Can you advise on which is the best raid level that I can use. I would like to use raid 10 but I am not sure how this has to be configured?
Thank you.

Hello,
Really cant advise on which RAID level is best cause it depends on what you looking for, best write performance, more reliability, fault tolerance or if you dont mind setting a disk as hot spare (will have no info at all and just wait for a disk to fail so it can takes its place); in other words there is a variaty of options and all may or may not be good depending on your needs.
In this case, to configure RAID 10 with that controller, you will need to reboot the server and access the PCIe controller with "Ctrl+H" when prompted during the boot process. You will be prompted with a screen that will ask you to select the controller you want to access, since there is only one just select it.
Next screen will be something like the below (but will ALL disks unconfigured), select "Configuration Wizard" and configure manually
In the next screen, choose
1-"New Configuration"
2-"Manual Configuration"
3-Select 2 disk and click on "Add To Array", do this steps for the remaining 2 disk so you can form 2 groups
4-Click on "Accept DG"
5-Click on "Next"
6-Next screen will show you both of the arrays you created in step 3, select the first and click "Add to SPAN" (repeat for the other array you created)
7-Click on "Next"
8-You will now see an screen like this one where you will be able to select RAID 10 (if it does not show up, the arrays were either not properly created or not added to SPAN like in step 6 above)
Note: The other options are:
-strip size: portion of a stripe that resides on a single drive in the drive group. The stripe consists of the data segments that the RAID controller writes across multiple drives, not including parity drives.
-Access Policy:
*RW—Allows read/write access. This is the default.
*Read Only—Allows read-only access.
*Blocked—Does not allow access.
Read Policy
*Normal—Disables the read-ahead capability. This is the default.
*Ahead—Enables read-ahead capability, which allows the controller to read sequentially ahead of requested data and to store the additional data in cache memory, anticipating that the data will be needed soon. This speeds up reads for sequential data but there is little improvement when accessing random data.
Write Policy
*WBack—(Writeback) the controller sends a data transfer completion signal to the host when the controller cache has received all of the data in a transaction. This setting is recommended in Standard mode.
*WThru—(Writethrough) the controller sends a data transfer completion signal to the host when the drive subsystem has received all of the data in a transaction. This is the default.
*Bad BBU—Choose this mode if you want the controller to use Writeback mode but the controller has no BBU or the BBU is bad. If you do not choose this option, the controller firmware automatically switches to Writethrough mode if it detects a bad or missing BBU.
With the new version 1.5, this can also be done with CIMC without having to reboot the server.
I hope this helps but let me know if there is any doubt.
-Rate all helpful answers.
Kenny

UCS C-Series Server discovery with UCSM integration failed

Hi, i try to install C460M2 and a C260M2 via fex 2232PP
Because we are waiting for delivery of VIC Cards I have to install the Servers via 2 wire.
This means I connected each Server with the 2 LOM gigabit ports to the nexus 2232PP (one port ono each nexus), and I also connected the 10 ge LOM to each of the nexus 2232PP.
My problem is the nexus 2232 are discovered, but no one of my servers get discovered. All Ports have link up, I can not find any log message on discovery error.
I know the 10 GE Server Ports are not supported, but I think the servers should get discovered.
Does anybody have an idea, wherecan I find all logg information and what filter ist suggested ?
Best Regards Alois
Sent from Cisco Technical Support iPad App

Hi Keny,
I tried to powercycle both servers (c260M2 and C460M2) but still no discovered server and also no logg.
I checked
Rack Server Discovery Policy == immediate
Rack management Connecton Policy == Auto Achnowledged
Chassis/Fex Doscovery Policy == 2 Link and Port-Channel (As I installed 2232PP I moved to Port Channel)
I am running UCSM Version 2.1(1e)
FI 6248 Version 5.0(3)N2(2.11e)
2232PP run on same as FI
I also have a connected 5108 with IOM 2104 running on 2.1(1e) Version.
CIMC Version of C260M2 and C460M2 will be checked tomorrow when my kolleague is in the datacenter.
Server Connection is not really the same like in http://www.cisco.com/en/US/docs/unified_computing/ucs/c-series_integration/ucsm2.1/b_UCSM2-1_C-Integration_chapter_011.html
Because I still have no VIC Card but the connections are the same.
C260 GE LOM1 <-> FEX2 Port 11
C260 GE LOM2 <-> FEX3 Port 11
C260 10 GE LOM1 (PCIE Slot4) <-> FEX2 Port 12
C260 10 GE LOM2 (PCIE Slot4) <-> FEX3 Port 12
GE LOM ist position 13 and 10 GE LOM is position 11 in the techspech of c260
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C260/install/overview.html#wp1243740
C460 GE LOM1 <-> FEX2 Port 10
C460 GE LOM2 <-> FEX3 Port 10
C460 10 GE LOM1 <-> FEX2 Port 9
C460 10 GE LOM2 <-> FEX3 Port 9
GE LOM ist postion 8 and 10 GE LOM ist position 7
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C460/install/overview.html#wp1243740
With C260 I also tried a reboot with disconnected 10 GE Ports, but also no discoverd Server until now.
Regards Alois

FTP on Mac OS X Server - not accessible from outside

I need to set up FTP on my mac mini urgently as I need to share over 0,5 TB of video material for a "last-minute" production.
I have set everything up wth shares and all and have a "XYZ" user under "Local Network User" so i can give others this username/password and have services FTP and File Sharing enabled for this user. Yet I can not connect to my server via FTP and 21 port from outside world, although FTP is enabled both on router and as a service in Mac OSX Server app.
What am I doing wrong? VPN and other services such as email and the rest are working like a charm.
Thanks so much!

Any ideas? Still struggling with this problem...

Data services job failes while insert data into SQL server from Linux

SAP data services (data quality) server is running on LInux server and Windows. Data services jobs which uses the ODBC driver to connect to SQL server is failing after selecting few thousand records with following reason as per data services log on Linux server. We can run the same data services job from Windows server, the only difference here is it is using SQL server drivers provided by microsoft. So the possible errors provided below, out of which #1 and #4 may not be the reason of job failure. DBA checked on other errors and confirmed that transaction log size is unlimited and system has space.
Why the same job runs from Windows server and fails from Linux ? It is because the ODBC drivers from windows and Linux works in different way? OR there is conflict in the data services job with ODBC driver.
===== Error Log ===================
8/25/2009 11:51:51 AM Execution of <Regular Load Operations> for target <DQ_PARSE_INFO> failed. Possible causes: (1) Error in the SQL syntax;
(2)6902 3954215840 RUN-051005 8/25/2009 11:51:51 AM Database connection is broken; (3) Database related errors such as transaction log is full, etc.; (4) The user defined in the
6902 3954215840 RUN-051005 8/25/2009 11:51:51 AM datastore has insufficient privileges to execute the SQL. If the error is for preload or postload operation, or if it is for
===== Error Log ===================

this is another method
http://www.mssqltips.com/sqlservertip/2484/import-data-from-microsoft-access-to-sql-server/
Please Mark This As Answer if it helps to solve the issue Visakh ---------------------------- http://visakhm.blogspot.com/ https://www.facebook.com/VmBlogs

UCS C Series hardware monitoring

Does anybody know how we could monitor the UCS C Series hardware (power supply, Hard disk, Memory ect...) within SolarWinds. We usually monitor servers via SNMP. It looks like there is the CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB that is supported on UCS manager 1.4 and above. When I to poll the box for those MIB's I get the OID is not supported. The UCS C Series server is on 1.3(2j) for the firmware version. Do we need to upgrade to 1.4 to get the equipment monitoring to work or is there another way? I notice a lot of users are monitoring B Series in Solarwinds but I haven't really seen anything on C Series.
Any thoughts would be appreciated.

Hello,
Yes, CIMC 1.4 has additional SNMP functionality.
ftp://ftp.cisco.com/pub/mibs/supportlists/ucs/ucs-C-supportlist.html
-------- snip -------------
Release 1.4(3)
provides SNMP V1/V2c/V3 support for inventory and fault monitoring of fans, power supplies, CPU, Memory and Storage Controllers, Physical Drives, Logical Drives and Battery Backup Units. The SNMP agent supports SNMP V1/V2c/V3 traps and V2c informs. This release also carries further the MIB-II Implementation, from the previous release, for “System”, “Interfaces” and “SNMP”.
UCS top level OID -- 1.3.6.1.4.1.9.9.719.
719.1.1.1.1 -- fault table
719.1.15 -- Inventory table
OID for specific components,
719.1.15.12 -- Fan
719.1.15.56 -- PSU
719.1.30      -- Memory
719.1.41      -- CPU
719.1.45      -- Storage ( controller , LUN , disks and BBU table )
HTH
Padma

UCS B series IOM firmware upgarde.

Dear Experts;
We have one BUG in our UCS B series server as below link.
https://tools.cisco.com/bugsearch/bug/CSCue49366/?reffering_site=dumpcr
The work around is to do the IOM firmware upgarde.
As teher are several Firmware are associated with the UCS system how to knwo the dependency and how to know which firmware is compatible with the uCS server.
Please assist me to get teh proper IOM firmware .I opened one TAC and they are telling TAC doesn't support this we have to contact cisco AS team and we don't have cisco AS team contract.
Regards
Debashis

Dear Walter;
Really appreciated your expert technical advice.
I have one small question as below if you can answer it..
As per the existing setup..
This UCS system is connected with the EMC storage Model:VMAX-1SE Version:5876.
We have no idea if UCS firmware version 2.1(3c) is compatible with the MC storage Model:VMAX-1SE Version:5876..
I have opened the TAC and also went through the Compatibility matrix where it mentioned as attached and to conatct EMC vendor.
We opened case with EMC they are telling contact Cisco and Cisco TAC telling contact EMC.
IS there any way we can know this?
Note as per the attachment:
5. Direct Connect FC/FCoE topologies are supported with this array.
6. Non-default adapter settings are typically required by storage vendors and found on their support list.
7.Multiple array and switch models supported with UCS by the storage vendor are on their support list.
12.iSCSI Boot is supported Both Appliance and Uplink ports are supported unless otherwise noted.
26. Supported for NFS/CIFS access via appliance ports on the Fabric Interconnect

UCS C-Series w/P18E CNA - Boot from SAN via FCoE?

Does anyone have a link to a document on how to configure a C-Series server w/P18E CNA's to boot from SAN via FCoE? I can't seem to find much info.
Thanks!

Hello Rogelio,
The following documents might help you on it.
Cisco P81E configuration information
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/sw/gui/config/guide/1.4.1/Cisco_UCS_C-Series_GUI_Configuration_Guide_141_chapter9.html
Basic Nexus 5K switchport configuration
http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps9670/guide_c07-690080_ns1118_Networking_Solutions_White_Paper.html#wp9000629
HTH
Padma

Site not accessible from the Load balanced web front end server - sharepoint 2010

I have a production environment with 2 WFE's(sp-wfe1 & sp-wfe2), 2 APP's and 2 SQL clustered VM's.
2 WFE's are load balanced using hardware load balancer.
An A-Record(PORTAL) is created in DNS for the virtual IP of the load balancer which points to the 2 WFE's.
A web application is created on the WFE's on port 80.
alternative access mapping is configured and the load balanced record "http://PORTAL" is used under the default zone.
Under IIS I have edited the bindings for the sharepoint site at port 80 and added the HOSTNAME as PORTAL.
Result: The site is accessible from outside the server and works fine.
ISSUE: The site is not accessible within the WFE's(sp-wfe1 & sp-wfe2).
When I browse the site from the WFE's server it ask for the credentials and when I enter the credentials and click OK it ask the credentials again and again and in the end displays a blank page.
Kindly help me in this issue because I am clueless and couldn't find anything helpful on the internet.
Regards,
Mudassar
MADDY-DEV Forum answers from Microsoft Forum

Loop back check.
http://www.harbar.net/archive/2009/07/02/disableloopbackcheck-amp-sharepoint-what-every-admin-and-developer-should-know.aspx

Download OAF pages from linux server

Dear All,
I want to download OAF pages(per) from linux server
I already download below paths
$JAVA_TOP/oracle/apps/per
$APPL_TOP/per/mds
but previous paths don't contain java class
******CO.java
******VOImpl.java
******EOVORowImpl.java
******AMImpl.java
so from where can I get previous java classes.
Thanks in Advance

The pages are stored in the MDS repository. You can use the pl/sql package jdr_util's to extract them. Please see the link below for help using jdr_utils:
oracle.anilpassi.com/jdr-utils-2.html
Kristofer Cruz

Application Catalog website only accessible from server - clients give 401

Hi,
I have a weird problem, something has gone screwy in the IIS config I think.
I've had the SCCM 2010 R2 application catalog set up and running fine for some time. Recently I installed MBAM (Bitlocker Management) on the SCCM server. MBAM creates it's own website in IIS.
Following installation of MBAM the application catalog isn't fully working.
Clients trying to access http://servername/CMApplicationCatalog get asked repeatedly for credentials before getting a 401 error.
Clients accessing http://SERVER.IP4.ADDRESS/CMApplicationCatalog or http://servername/CMApplicationCatalog from the server see the application catalog without an authentication prompt (although they get an error if they try to install anything)
Browsing to http://localhost/CMApplicationCatalog from the server works properly - no authentication prompt and can install software.
The server is in the list of IE trusted sites. I've tried removing and reinstalling the Application Catalog roles.
Any idea what the problem is here?
Thanks,
Tim

Hi,
Thanks both - I don't see anyhthing strange in the IIS logs.
This is an example of it failing trying to access it by name manually entering details in the authentication box.
10.0.0.100 GET /cMApplicationCatalog/ - 80 - 10.0.0.163 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.3;+WOW64;+Trident/7.0;+.NET4.0E;+.NET4.0C;+InfoPath.3;+.NET+CLR+3.5.30729;+.NET+CLR+2.0.50727;+.NET+CLR+3.0.30729)
- 401 2 5 1542 1268
10.0.0.100 GET /cMApplicationCatalog/ - 80 - 10.0.0.163 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.3;+WOW64;+Trident/7.0;+.NET4.0E;+.NET4.0C;+InfoPath.3;+.NET+CLR+3.5.30729;+.NET+CLR+2.0.50727;+.NET+CLR+3.0.30729)
- 401 2 5 1542 3
10.0.0.100 GET /cMApplicationCatalog/ - 80 - 10.0.0.163 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.3;+WOW64;+Trident/7.0;+.NET4.0E;+.NET4.0C;+InfoPath.3;+.NET+CLR+3.5.30729;+.NET+CLR+2.0.50727;+.NET+CLR+3.0.30729)
- 401 2 5 1542 2
10.0.0.100 CCM_POST /bgb/handler.ashx RequestType=LogIn 80 - 10.0.0.163 ccmhttp - 200 0 0 304 0
10.0.0.100 GET /browserconfig.xml - 80 - 10.0.0.163 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.3;+Win64;+x64;+Trident/7.0;+.NET4.0E;+.NET4.0C;+InfoPath.3;+.NET+CLR+3.5.30729;+.NET+CLR+2.0.50727;+.NET+CLR+3.0.30729)
- 404 0 2 1405 2
10.0.0.100 CCM_POST /bgb/handler.ashx RequestType=Continue 80 - 10.0.0.163 ccmhttp - 200 0 0 1258 4405
This is accessing it by IP, with the transparent authentication working.
10.0.0.100 GET /cMApplicationCatalog/ - 80 - 10.0.0.163 Mozilla/5.0+(Windows+NT+6.3;+WOW64;+Trident/7.0;+rv:11.0)+like+Gecko - 401 2 5 1542 1
10.0.0.100 GET /cMApplicationCatalog/ - 80 DOMAIN-LOCAL\USER 10.0.0.163 Mozilla/5.0+(Windows+NT+6.3;+WOW64;+Trident/7.0;+rv:11.0)+like+Gecko - 200 0 0 1851 224
10.0.0.100 GET /cMApplicationCatalog/ClientBin/en-GB/en-GB.xap - 80 DOMAIN-LOCAL\USER 10.0.0.163 Mozilla/5.0+(Windows+NT+6.3;+WOW64;+Trident/7.0;+rv:11.0)+like+Gecko http://10.0.0.100/cMApplicationCatalog/ClientBin/Microsoft.ConfigurationManager.SoftwareCatalog.Portal.xap?ver=5.0.7958.1000
404 0 2 1461 1
10.0.0.100 GET /cMApplicationCatalog/ClientBin/en/en.xap - 80 DOMAIN-LOCAL\USER 10.0.0.163 Mozilla/5.0+(Windows+NT+6.3;+WOW64;+Trident/7.0;+rv:11.0)+like+Gecko http://10.0.0.100/cMApplicationCatalog/ClientBin/Microsoft.ConfigurationManager.SoftwareCatalog.Portal.xap?ver=5.0.7958.1000
404 0 2 1461 2
10.0.0.100 POST /cMApplicationCatalog/ApplicationViewService.asmx - 80 DOMAIN-LOCAL\USER 10.0.0.163 Mozilla/5.0+(Windows+NT+6.3;+WOW64;+Trident/7.0;+rv:11.0)+like+Gecko http://10.0.0.100/cMApplicationCatalog/ClientBin/Microsoft.ConfigurationManager.SoftwareCatalog.Portal.xap?ver=5.0.7958.1000
200 0 0 772 429
10.0.0.100 POST /cMApplicationCatalog/ApplicationViewService.asmx - 80 DOMAIN-LOCAL\USER 10.0.0.163 Mozilla/5.0+(Windows+NT+6.3;+WOW64;+Trident/7.0;+rv:11.0)+like+Gecko http://10.0.0.100/cMApplicationCatalog/ClientBin/Microsoft.ConfigurationManager.SoftwareCatalog.Portal.xap?ver=5.0.7958.1000
200 0 0 2054 404
The difference I can see is that no credentials are showing in the logs in the top example.
I have checked IE settings which appear to be correct. Checking File -> Properties in IE shows the zone as Local intranet | Protected Mode: Off in both cases.
Tim

Ask the Expert: Cisco UCS B-Series Latest Version New Features

Welcome to this Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the Cisco UCS Manager 2.2(1) release, which delivers several important features and major enhancements in the fabric, compute, and operational areas. Some of these features include fabric scaling, VLANs, VIFs, IGMP groups, network endpoints, unidirectional link detection (UDLD) support, support for virtual machine queue (VMQ), direct connect C-Series to FI without FEX, direct KVM access, and several other features.
Teclus Dsouza is a customer support engineer from the Server Virtualization team at the Cisco Technical Assistance Center in Bangalore, India. He has over 15 years of total IT experience. He has worked across different technologies and a wide range of data center products. He is an expert in Cisco Nexus 1000V and Cisco UCS products. He has more than 6 years of experience on VMware virtualization products.
Chetan Parik is a customer support engineer from the Server Virtualization team at the Cisco Technical Assistance Center in Bangalore, India. He has seven years of total experience. He has worked on a wide range of Cisco data center products such as Cisco UCS and Cisco Nexus 1000V. He also has five years of experience on VMware virtualization products.
Remember to use the rating system to let Teclus and Chetan know if you have received an adequate response.
Because of the volume expected during this event, our experts might not be able to answer every question. Remember that you can continue the conversation in the Data Center community, under subcommunity Unified Computing, shortly after the event. This event lasts through May 9, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hi Jackson,
Yes its is possible. Connect the storage array to the fabric interconnects using two 10GB links per storage processor. Connect each SP to both fabric interconnects and configure the ports on the fabric interconnect as “Appliance” ports from UCSM
For more information on how to connect Netapp storage using other protocols like iSCSI or FCOE please check the url below.
http://www.cisco.com/c/en/us/products/collateral/servers-unified-computing/ucs-6100-series-fabric-interconnects/whitepaper_c11-702584.html
Regards
Teclus Dsouza

Does the UCS C-Series Servers supports PCI/e card digium T1/E1

Hello,
Does the UCS C-Series Servers supports/compatible with PCI/e card digium TE407P/TE420 T1/E1.?
The server will be used as Asterisk server.
Thanks
Philip

Hi Philip,
Compatibility will depend on the server model that you have and whether the digium card is a full length, low profile, or half length pcie card. Take a look at http://www.cisco.com/en/US/products/ps10493/prod_models_comparison.html#~tab-a for details. If there are any issues with the card itself once it is installed it will have to go through the 3rd party manufacturer.

UCS C Series SAN Boot

Hi All,
How to configure SAN Boot on the UCS C Series platform ?
On B Series, we can configure the boot order from vHBA, but on the UCS C Series I found nothing.
The C Series SAN boot had being enabled and also the boot target was configured on the vHBA properties, but the C Series can't boot from SAN
Attached are the detailed of the configuration on C Series
Please help, if you have C Series boot from SAN succesfully
Thanks,
Gofi

Hi Padma,
Yes, that will be the flogi into the upstream switch.
Below are the configurations of Nexus 5K, while I used 2 N5k as the upstream FCoE switch
N5K1# sh run int vfc113
!Command: show running-config interface vfc113
!Time: Wed Jun 17 03:21:56 2009
version 5.2(1)N1(5)
interface vfc113
bind interface Ethernet113/1/1
switchport trunk allowed vsan 10
no shutdown
N5K1# sh run int eth113/1/1
!Command: show running-config interface Ethernet113/1/1
!Time: Wed Jun 17 03:22:05 2009
version 5.2(1)N1(5)
interface Ethernet113/1/1
switchport mode trunk
switchport trunk allowed vlan 10,120,125,130,135,200-201
N5K1# sh run | sec fex
feature fex
fex 113
pinning max-links 1
description "FEX0113"
fcoe
fex 123
pinning max-links 1
description "FEX0123"
N5K1# sh feature | i fcoe
fcoe                  1         enabled
fcoe-npv              1         disabled
N5K2# sh run int vfc123
!Command: show running-config interface vfc123
!Time: Wed Jun 17 03:24:12 2009
version 5.2(1)N1(5)
interface vfc123
bind interface Ethernet123/1/1
switchport trunk allowed vsan 20
no shutdown
N5K2# sh run int eth123/1/1
!Command: show running-config interface Ethernet123/1/1
!Time: Wed Jun 17 03:24:29 2009
version 5.2(1)N1(5)
interface Ethernet123/1/1
switchport mode trunk
switchport trunk allowed vlan 20,120,125,130,135,200-201
N5K2# sh run | sec fex
feature fex
fex 113
pinning max-links 1
description "FEX0113"
fex 123
pinning max-links 1
description "FEX0123"
fcoe
N5K2# sh feature | i fcoe
fcoe                  1         enabled
fcoe-npv              1         disabled
The CNA server connected to FEX Nexus 2K, while the Nexus uplinks are controlled by 2 Nexus 5Ks (vPC on the N5K)
Any suggestions ?
Thanks,
Gofi

PXE Errors - new install of CUCM on UCS C series servers

Hi All
I'm in a middle of production install of CUCM , CUWL and IM and Presence on Cisco UCS Servers C220 and C240.
Until last friday I borught the CUCM cluster along with CUWL server online and lastly just completed the install of IM and Presence PUB left home.
Then tried logging on Sunday from home via vSphere client unable to connect to these boxes and the webURL's either of apps didn't work.
I presumed something and then tried to gain access via CIMC port and after launching KVM console I see the attached PXE errors.?
I'm not sure why this happend all of a sudden nothing changed in the boot order nor in the network.
Please send me into right direction....this structure I had up and running from last one week and phones registered too.
Thanks
Mohammed

Never mind I figured it out myself and you'll surpised how fragile the UCS C series servers are as I was running them on single power supply and the inside hardware was acting weird for this purpose and once I connected the second power supply and rebooted the server the vmware loads and everything is back online.
How strange this issue was ...
Thanks
Mohammed

UCS C series server whether accessible from Linux prompt

Similar Messages

Maybe you are looking for