UCS C220 not recognizing LSI 9266 MegaRaid card

I just received a new UCS c220 with a seperate LSI 9266 MegaRaid card. I have installed the card adn connected the SAS cables and BBU. When I start the server it doesn't recogize the card. If go into CIMC the card is not listed. I have changed the SAS cables and resetted them all several times. I have resetted the card several times. I have not changed any of the settings yet so I may be missing something there that will make it recongize the card but I have followed all available instructions as well. Any thoughts on what I could be missing?

Yes I have it installed in PCIe2 per the instructions. It won't fit in PCIe1 anyway . I have also looked up the LSI card specs to make sure I have the cables correctly attached. See attached images for configuration in BIOS as Robert suggests and evidence of cabling and PCI location.
Thanks for the assist.

Similar Messages

Centro not recognizing Kingston SDHC 4GB Card

I purchased the Centro last week and also bought (from a third party) a Kingston 4GB SDHC Card. Initial installation of the card took a couple tries before it was recognized by the Centro. After initial recognition, I used the Centro utility to format it, then used a USB adapter to load an album on it from my laptop. The Centro immediately recognized the card upon reinsertion and the music played as expected.
However, the Centro loses contact with the card regularly. I check about 10 times a day and at least half of the time the Centro registers "No Card Inserted" in the Card Info application. I tried a soft reset to no avail. The hard reset has increased the number of times the card is recognized, but the Centro is still not consistently recognizing the card.
I'd appreciate any help you can give - at the moment I'm down to buying another card just to see if its the card or the Centro. The problem I'm anticipating is having the card people tell me its the device and the device people tell me its the card!
Thanks!
Post relates to: Centro (Verizon)

Also have you uprgaded from a previous palm os device? There could be something that is save in your backup folder that when you resync it recognizes that file again and causes the lost card.
Out or curiosity if you hard reset the device (http://kb.palm.com solution id 887)
Then put the card in it works fine, next try syncing, but to a different username than your normal one, does the card still get recognized or is it lost in the shuffle again?
I have a Centro, Sprint and have synced many times and do not have any problems with my device recognizing the card.
Post relates to: Centro (Sprint)

3GS not recognizing AT&T sim card

Hello all. I tried to search for this issue before posting but came up empty. I just inherited a 3GS from a friend when he upgraded. Whenever I try to activate it through iTunes, it tells me the sim card is not supported. As far as I can tell, I've done everything right so far. Got an iphone data plan through AT&T and have a new sim card (actually on the 3rd one since we kept thinking it was the sim card that was bad). I asked my friend, and he's confused cuz the phone worked for him when I gave it back for him to look at. The only difference between us is he's a PC and I'm a Mac, but that shouldn't change anything, should it? Or does the phone need to be reformatted in order to recognize my sim card?
::exasperated sigh:: Would love a working phone soon. ^_^

No,it's not possible.

Direct X Not recognizing a Mac Video Card in XP Mode

I have XP running in Parallels on my Macbook and am trying to install a piece of XP compat software. Get an error message saying no compatible graphics card can be found by Direct X. Program will exit.
Any idea how to get the card regognized by Direct X?
Thanks
Tartan
Macbook Pro Mac OS X (10.4.9)

Since Parallels is not an Apple product, you'd probably be better off posting your question on the Parallels discussion boards, rather than an Apple forum.
Be sure to search the forum first in case someone has already had a similar question answered. You'll get your answer faster this way. Post your question in the forum if you don't find anything that helps you.
http://forums.parallels.com

UCS Chassis Not Recognized

Hello,
I am having a strange issue with a new UCS environment that we just brought online. One of the four UCS chassis had an issue with its firmware upgrade, specifically the IO module. All of the other componants on all of the other UCS chassis upgraded just fine but these two IO modules hung during the firmware upgrade. I tried to downgrade the firmware on all of the other componants to match the hung IO modules to see if they would come back online and they did not. I also moved the IO modules into a known working chassis and they worked after an auto-upgrade of the firmware! I then swapped them back to their original chassis thinking that they would be ok but they went down again, stating a communication problem and the 6140 reported them as being link-down. I restarted the entire chassis and also swapped the uplink cables and still they show offline. As a last ditch effort I deleted the entire chassis and went back to re-add it and now it will not even detect the chassis.
I know that the IO modules are fine because I can put them in another chassis and they will come up but as soon I put them back in their original chassis, the 6140's report the link as being down and it will not recognize the chassis. Does this sound like a hardware issue with the chassis itself? Any ideas?

Can you try using the cables from your "good" Chassis on the failing one?
I'd suggest you completely power down the bad chassis. Take the cables from a good chassis, move them over, then power the bad Chassis back up.
If this doesn't work let me know. Also ensure your Chassis discovery policy is set to 1 link for now.
Robert

Nokia 6205 not recognizing pics on memory card

My brand new Nokia 6205 won't recognize my pictures from my old phone and load them onto this new phone. They're saved on my SD memory card.
I have pictures of my dog that I lost on mothers day. I've missed him since he passed away and I want to use them as my wallpaper like I did one my old phone and they won't come up anyone know how to get this phone to recognize them
I'm madder than a wet hen over this it's the whole reason I picked this phone because of the removable memory
Thanks for any help

17-Sep-2008 03:19 PM
edna wrote:
My brand new Nokia 6205 won't recognize my pictures from my old phone and load them onto this new phone. They're saved on my SD memory card.
I have pictures of my dog that I lost on mothers day. I've missed him since he passed away and I want to use them as my wallpaper like I did one my old phone and they won't come up anyone know how to get this phone to recognize them
I'm madder than a wet hen over this it's the whole reason I picked this phone because of the removable memory
Thanks for any help
Insert your old memory card to a card reader - and connect it to a PC. Then copy the files to your new microSD card.
Nokia 6205 is an exclusive phone made for Verizon right?

PCI-Servo-4A cards not recognized by computer

After shipping a computer with PCI-Servo-4A cards (which had been working for 2 years), my computer did not recognized several of the cards. These cards are not recognized in other working computers, and both computers recognize other "good" PCI-Servo-4A cards. There is a hardware failure on the cards (I have 10 with this problem). Has anyone repaired PCI-Servo-4A cards with this problem, and is there a "shotgun approach" to replacing a most likely culprit part?
Thanks

Hello,
You can have your cards repaired by National Instruments. Goto ni.com/ask to generate a service request number and then call in with that number to RMA your boards.
Regards,
Yusuf C.
Applications Engineering
National Instruments

Sd card reader on MBP not recognizing SD card

The SD card reader on my MBP is not recognizing a new SD card. I have tried taking it out and putting it back in. I looked in disk utility, but do not see it listed. "I also tried image capture. What else can I try?

If you have photos on the SD card try using Image Capture to download the photos to a folder on the Desktop before you reformat the card with the camera.
OT

Photoshop CS2 avtivation not recognized

Photoshop CS2 activation not recognized after ATI graphics card driver update. Internet connection live but "No internet connection detected" indicated when trying to reactivate. What's going on???

Adobe shut down the CS2 activation servers months ago. You are entitled to download the free CS2 copy. Use the s/n supplied on website.

IPhone 4 not recognized when connected to new USB 2.0 card

I have an iphone 4 OS4.1 on a no-name Windows XP Pro (service pack 3) PC with an AMD processor and lots of RAM.
I had the phone working and syncing beautifully with the onboard USB 1.1 but it was slow. So I bought a new PCI USB 2.0 card and installed it. Card is installed and there are no problems according to the status in System Devices.
But the computer does not recognize the iphone when plugged into one of those ports. If I plug it into one of the USB 1.1 ports that are still in the machine, it syncs and works fine. If I plug it into one of the new USB 2.0 ports, the PC shows the window at bottom right saying the device is not recognized. Tried the wizard but it's useless.
THOUGHTS?????

Nevermind!!!
It turned out to be a faulty cable! I tried it with a different sync cable and it works fine!
So disregard the question above.

GeForce4 TI Video Card Not Recognized Anymore?

For about almost a year, the fan on the GeForce4 TI video card would occasionally make a grinding noise, although it has always been easily fixed by lightly sticking a finger on the fan to stop it for a second and it would go back to normal.
However, about a month ago this little fix stopped working. The grinding noise was unbearable. After searching the Internet for a few minutes, I found out that I wasn't the only one suffering from this problem, and some even offered tips on how to replace the fan.
I followed the steps very carefully and made sure the card was not harmed. After installing the new fan, which was very easy, I stuck it back into the Power Mac and boot it up. However the monitor didn't find a signal.
I was glad that I installed Remote Desktop on the Power Mac so I was able to connect to it and see what's going on. I opened Apple System Profiler and noticed that the computer isn't properly recognizing the graphics card anymore! Instead of the very detailed information I'm used to seeing, this is what I saw below:
pci10de,a:
Type: VGA-Compatible Controller
Bus: AGP
Slot: SLOT-1
Vendor: nVIDIA (0x10de)
Device ID: 0x252
Revision ID: 0x00a3
I have no clue what this means as it seems like the computer still recognizes A video card. Also this also gave me the impression that the Power Mac is missing the drivers, but that's impossible as I haven't touched the software on the hard drive and nVidia drivers are part of OS X.
If the card is broken then fine, I'll take my losses and buy a new one as I would hate to just throw the computer away since it still more than fulfill my needs. But I just hope the AGP slot isn't broken.
Any ideas? Thanks in advance.

Just for clarification:
You have two systems based on the same MS-7008 mainboard, correct? Both use the same BIOS Version?
In one system, the card is functioning, running in AGP 3.0 Mode x8 and in the other, same mainboard model, what are the symptoms of "video card not recognized" besides the AGP 2.0 Mode x4 limitation?
I mean, if you can see the BIOS Setup, the card is putting something out on the screen, right?

I got an itunes giftcard for my birthday and when i tried to add it on my balance on my ipod touch it says the code you entered is not recognized as a valid code. but i just got this card brand new for my birthday.

i got an itunes giftcard for my birthday and when i tried to add it on my balance on my ipod touch it says the code you entered is not recognized as a valid code. but i just got this card brand new for my birthday.

Make sure you're using the correct code. For most iTunes cards, the code is under the scratchoff area on the back of the card. For more information, see this support article:
http://support.apple.com/kb/TS1292
If you can't get to work after perusing that page, contact the iTunes Store Support; instructions are at the bottom of that article.
Regards.

Graphics card is not recognized in windows 7

Hi guys, i just installed windows 7 ultimate on my bootcamp partition. Everything loaded fine. I used my osx disk to install bootcamp, it worked. But my video card (Nvidia geforce gt 330m) is not recognized or something. i checked device manager and under display there is only standard VGA driver. I went to the nvidia website and downloaded the driver but when i go to install it, it says: the nvidia setup could not find any drivers that supports your hardware.
Any ideas??
my video card works perfectly on mac...

^^Gecko, I'm not bustin' on you, but you're wrong. Or, you are, but I doubt it, one of the lucky ones.
I've gotten 3.1 installed by running the setup .exe file from the DVD via Windows Explorer. Everything seems OK except the graphics/resolution. My NVIDIA card isn't recognized and my resolution options only go up to 1280 x 800.
The Window 7 Performance Information and Tools shows this:
"Graphics
Total available graphics memory Not detected
Dedicated graphics memory 0 MB
Dedicated system memory 0 MB
Shared system memory 0 MB
Display adapter driver version 6.1.7600.16385
Primary monitor resolution 1280x800
DirectX version DirectX 8 or earlier"
Apple, please, help us!
Message was edited by: K Dubb
Message was edited by: K Dubb

Why are my PXI cards not recognized by Windows or MAX?

I have a PXI-1045 chassis connected to a PC through MXI-4. When I turn the chassis and PC on with a PXI card in slot 2, the message "Windows could not load the installer for DAQDevice. Contact your hardware vendor for assistance." appears, and the PXI card is not recognized (it is scene by Windows as an unidentifiable PCI Devices, though I have a DAQmx installed).
More details:
Windows XP
LabVIEW 8.0 installed
TestStand 4.0 installed
Latest DAQmx 8.XX installed
NI Scope installed
NI CAN installed
MXI-4 PCI card installed in PC and recognized by Windows (as PCI-PCI bridge, and MXI-4 Device)
I identified PXI chassis 1045 in MAX and on subsequent boot up saw that MAX complained about pxisys or some other ini file (in the chassis status area of the screen) so I configured it as 'other' then put in the PXI-resorce CD and selected the ini file for PXI-1045, MAX no longer complains about pxisys and instead says the chassis is configured properly
If I have nothing but the PXI MXI-4 card installed in the PXI system and boot up the chassis then the PC, I get no errors
If I have a card in slot two (I've tried PXI-6509 Industrial Digital IO, PXI-2569 Relay Module, and PXI-5102 Digital Oscilliscope) and boot the chassis then PC, the message "Windows could not load the installer for DAQDevice. Contact your hardware vendor for assistance." shows up when Windows boots and Windows sees a PCI Device but can't identify any drivers for it.

Hello,
Can you post a screenshot of the problem? Are you switching on the chassis first or the PC? Please make sure that you switch ON chassis and then boot the PC. This typically happens when you have a corrupted installation. I would suggest downloading the latest version of driver from here and re-installing it.
Please uninstall all the driver software from computer before installing the new software.
http://digital.ni.com/softlib.nsf/websearch/d31d46fffb745eca862571490053eab8
Thanks,
Kalyan
Applications Engineer
National Instruments

Airport card is not recognized by G3 iMac

I recently acquired a G3 600 MHz iMac, running OS X 10.4.11, and I want to join the iMac to my wireless network. So I purchased an Airport card ( tested card on a ibook running 10.4.11 and it works fine.) and seated it in the G3 iMac. For some reason the iMac does not recognize it one bit. I checked profiler and System Preferences and no sign of an Airport Card. I then opened the iMac and reseated the card, I even changed out the adapter with another adapter I had. After researching online, some people suggested an archival OS restore. Although I would try that but unfortunately I do not have any of the original install disks. So my question is: does anyone know how I can make the os recognize the card?
Greatly appreciate the help.

There are two versions of the original AirPort card, and their identify can be determined using the information below.
The poster you replied to may be referring to this post quoted below, though even if he had the initially issued card, it would not explain why the card is not recognized. Though incapable of supporting advanced security, it would otherwise be recognized and operate as expected if seated properly, as you have described.
The original AirPort card was equivalent to a WaveLAN Silver card, and supported only 40-bit WEP or 64-bit encryption, and did not support WPA.
The original AirPort Base Station which shipped with these cards on board was limited to 10 clients, had only a 10BbaseT LAN port, and supported only 40-bit WEP. Later cards which looked physically identical, supported 104 bit WEP, or 128-bit encryption, as did the AirPort Base Stations which included them. This second card, also manufactured initially in the Netherlands for Apple by AT&T's Lucent unit—later know as ORiNOCO—was equivalent to the WaveLAN Gold card.
The 661-2219 part number is distinguished by the M7600LL/* marketing designator screened on the label, as well as engineering revision part number 825-4889 and worldwide procurement part number 630-2883. EEE code G3G is embedded right-most in the last four characters of each part's serial number. *This character is typically A, B or C.
The 661-2569, on the other hand, is distinguished by an M7600LL/D or later marketing designator, engineering revision part number 825-5620, the same worldwide procurement part number 630-2883 and typically the phrase '128 bits' along the lower center of the label. EEE codes LH8, M6Y or QAC are embedded right-most in the last four characters of each part's serial number.
While a procurement number generally changes when a service part number change is made, this product did not, as Lucent remained its sole supplier, the 'change' to the card involved different firmware and not a physical change to the product, and Apple personnel largely considered them equivalent, though they were and are not.
Graphite AirPort base station models initially used the M7600LL/A, B or C cards, and was itself designated the M7601LL/A and later, the M7601LL/B. Both base stations were also designated as 661-2265 whole unit service replacement parts. Every card we've ever seen in a Graphite base station was a 661-2219 and was marked as described above.
Apple did not adequately document many of these parts and there applications at the time they were still in use, and all have disappeared from their inventory—except in limited cases—as has much of what existed for documentation. Given their personnel changes over the years, it's quite likely that no one there now can recall the subtle differences or properly identify these products. Once there are designated vintage, then obsolete, they drop quickly off of the radar.
While any properly functioning iMac compatible AirPort card properly mounted in a 076-0804 adapter would show up in the System Profiler without the antenna connected, the performance of such a card would be poor to abysmal.
I believe that you are completely correct when you indicate that either the adapter is not seated properly, that it is not working properly, or that the logic board is defective. The latter two scenarios are quite unlikely, though possible.

UCS C220 not recognizing LSI 9266 MegaRaid card

Similar Messages

Maybe you are looking for