UCS E140S - Broadcom Firmware and GE1/GE2

Hello,
I installed our E140S yesterday in a remote office and used the HUU ISO to upgrade all of the hardware to the latest version. After doing this, every time I login I get a popup suggesting that I upgrade the Broadcom 5719 Firmware. I have located the 5719 zip file on the developer site (linked from the popup message) but it is unclear how I should go about installing it. Any input here?
Also, I have connected the Console and Dedicated ports, but have not configured the GE1 and GE2 ports yet. Any guidance on how I should do this? I was thinking I should use an unnumbered interface since all I want is to link it to ESXi 5.1, but wanted to get an idea of what best practice is. I assume the are "virtual" interfaces within the router and as soon as I configure them (either with or without an IP) the will come alive?
Thanks in advance.
Mark

OK, a reboot of the CIMC took care of the Broadcom 5719 Firmware popup. Still curious on the details of the GE1 and GE2 interfaces though and how they should be utilized.
Thanks,
Mark

Similar Messages

Cisco Prime Infrastructure 2.2 - can we load PI2.2 on UCS-E140S-M2/K9 -

I am busy with an iWAN design and part of the solution is to have Cisco Prime deployed as a management tool.
The customer does not have VM and do not want an appliance.
The design caters for the new ISR4400 series routers.
We can add a UCS-E single wide server to the Core Router - UCS-E140S-M2/K9- can I load PI2.2?
The site will have 45 routers, 10 AP's - so will go with 50 lifecycle and assurance licences

I'm afraid this is supported officially. There are only two options :
> Installing as a virtual appliance - on an ESXi server.
> Using Cisco Physical Appliance
Installing directly on another hardware, be it UCS or other physical boxes is not supported. I am not sure if anyone would have tried to install and if there is a procedure to do so.
I can you want to try to burn the image as iso on DVD and install on your UCS box, it may have support issues from TAC whenever you'll reach out.
-Thanks
Vinod
**Encourage Contributors. RATE Them**

UCS-E140S KVM

Looking for the part number for the Single-Wide E-Series Server (UCS-E140S) KVM.

Hi carmenanderson ,
So, I checked with the Product manager and he said that unfortunately this is not an orderable part. Hence the lack of a PID.
Thanks.
-Bruce

IMac G3 won't boot after updating the firmware and upgrading the OS!

Hi! Everyone,
I have an iMac G3 333MHz (five flavors) which comes with 192MB of RAM and 6GB of hard drive. Originally, it was OS 8.5.1 installed, later upgraded to OS 9.2.2. Of course, the firmware has been updated by the appropriate method provided by the on-screen instructions before the installation of 9.2.2. After successfully updating the firmware and installing Mac OS 9.2.2, the system booted up and worked fine. However, after shutting it down and powering it up a few days later, I have encountered a critical problem:
1. At first, the iMac would chime and displayed a smiley-mac finder face.
2. No question mark appeared and the system halted because it stayed at the same screen for about 5 minutes! Also, the keyboard wouldn't respond. For instance, the LED signal light wouldn't light on when Caps Lock was pressed.
3. I assumed that this is just a typical crash and rebooted the machine via the "reset" button on the right side of the machine.
4. After restarting, well, no luck, the same condition. Therefore, I rebooted it again by using the method mentioned above.
5. The condition of sticking at the smiley-mac finder face occurred again! However, this time the iMac wouldn't chime and just displayed the mac face.
6. Another restart, well, it was getting worse... no chime and no smiley-mac finder face but a white screen.
7. I was frustrated then and shut the machine down forcefully by rebooting it again and pressing on the power bottom quickly before the screen appears. Also, I unplugged the power cord.
---------- After a few hours later ----------
8. Okay, I then plugged the power cord in and booted it up again, this time, it would chime but stuck at the white screen. => No smiley-mac finder face appeared!
9. Rebooted it again, the result was as same as step 8.
10. Another restart, the smiley-mac face finally appeared but still... stuck here and this time, no chime.
11. I then shut the machine forcefully by using the method mentioned above and let the machine rest for about a day with the power cord unplugged.
---------- After resting for a day ----------
12. I booted it up and it would chime, but no screen (the power button was orange, not green). I then forcefully shut down the machine.
13. Waited for about a minute and powered it up. This time, I tried to clear the PRAM, but no chime and gave me a white screen. => No luck! As mentioned, the keyboard's LED signal light wouldn't light on even though the Caps Lock key has been pressed.
*Note: The keyboard has been tested on the other computers and it worked. Also, I tried different USB ports to plug the keyboard in. => The USB ports were all in working condition， as I can know from the last successful start up.
14. Forcefully shut the machine down and tried to enter the Open firmware, no luck. It didn't enter and gave my a white screen.
15. Conclusion:
1) After resting for a while, the iMac would chime.
2) Rebooting too much times would cause the machine not to chime and leaded the screen to become white instead of the smiley-mac finder face.
3) However, rebooted the machine when the screen became white, the smiley-mac finder face would appear again without chime.
By the way, I could hear the hard disk spinning up so that means the hard disk is working.
Can anyone help me solve this problem? Is it related to the firmware update? Any suggestions will be appreciated! Thanks!
Andy

OK, I will try replacing the PRAM battery. Also, the PowerMac G3 and the other iMac 233MHz had the dead batteries. They are still working though... Should I replace them along with the iMac 333MHz? In case of not replacing, will they malfunction in future times? There are some symptoms on this two machines: 1. iMac 233MHz - No chime and no sound when adjusting system volume (the bi sound is not available), but iTunes and other applications can still use the audio device and output the sound via internal speakers; 2. PowerMac G3 450MHz - Will chime but sometimes hard to boot: 1) Chime but no screen; 2) No respond after pressing the power button => the power signal light won't light on. Every time I experienced this, I would open its case, pressing a small button (not quite understand what it does... anyway, just works if system halted.) near the PRAM battery and wait for about a minute, then close the case, and it boots. However, I have to reset "Date & Time"...

HT4623 I trying to update my iPad using iTunes. After connecting to MacBook Pro where is installed all latest software iPad is recognised as iPad, Serial Number: n/a. iTunes run recovery mode, trying to restore iPad firmware, and in the end unknown error

There was some updayts for my iPad 4 automatically downloaded. After installing it, the iPad began to restart itself every few minutes.
I tryed to update my iPad using iTunes. After connecting to MacBook Pro, where is installed all latest software, iPad is recognised as "iPad", Serial Number: n/a. iTunes run recovery mode, trying to restore iPad firmware, and in the end unknown error occured (3). Tried many times, not results. And now iPad stays only in recovery mode, can't switch it off. How can I solve this problem please?

When I restart my iPad the connect to iTunes comes up and stays on until it shuts down again, I have read a report from Apple support suggesting I reinstall iTunes so I might try that again and also your suggestion which i shall also try, but thanks again - rg1547

The bottom part of my iphone4 screen cannot tap.. restored 2 times with latest firmware and yet still the same..is it possible to fix this?how?

The bottom part of my iphone4 screen cannot tap.. I restored it 2 times with the latest firmware and yet still the same..is it possible to fix this?how? please guys help me =(

iPhone and iPod Touch: Troubleshooting touchscreen response: http://support.apple.com/kb/TS1827

I connected my iphone 3g to itunes which was in 4.1 firmware and itunes ask for an update which i downloaded an updated the phone to version 6.1.3 but my phone cannot start it shows no service my sim card is not getting network and i cannot use the phone.

i connected my iphone 3g to itunes which was in 4.1 firmware and itunes ask for an update which i downloaded an updated the phone to version 6.1.3 but my phone cannot start it shows no service my sim card is not getting network and i cannot use the phone. what should i do.?

First, you do not have a 3G if you could upgrade it to 6.1.3, because 4.2.1 is the last version that will work on the 3G. So you either have a 3GS or you somehow hacked the phone to install an incompatible version. You can check the model you have by entering your serial number here: https://selfsolve.apple.com/agreementWarrantyDynamic.do
Assuming you have a 3GS the most likely reason for your problem is you have a gray market phone that was hacked or jailbroken to unlock it. When you upgraded it you removed the hack, so the phone is now locked to its original carrier.

No firmware and no contact with PC with zen visio

I wanted to upgrade firmware and followed an instruction that told me to rebuild firmware first and then install the firmware upgrade. The update program doesnt say it is docked - although it states docked in the Vision M screen.
Appreciate any helpMessage Edited by borge on 04-3-20070:50 PM

Ok, I am assuming that either pc suite is so buggy that no one has had a chance to emulate this or that no one has this issue other than me and everyone is synchronising their outlook contacts with their N70 and are still able to us voice Tags?
If anyone is experiencing this issue can they please let me know I am not the only person having this problem or preferably if anyone knows a fix please let me know so I can either ignore and forget ever using voice tags or allow me to use what would be a really useful feature?
I am beginning to think this may be like a Microsoft built in feature
Cheers, B

Firmware and third party updates

Hi Everyone,
Currently I am running ARD version 3 on tiger server and I have Tiger and Leopard OS X running on my client machines (G5, Intel Mac).
I was wondering if there is a way to send Apple firmware and third party application updates to all of my Mac clients using ARD.
I have used "softwareupdate -i -a" and this command seems to be only working with Apple software but nothing else.
1. Is there a command that I can send (using ARD) to update firmware on all my Mac clients?
2. Is there a command to update third party software such as Adobe, Roxio etc?

1. No
2. Only by repackaging the updates into an Apple standard package installer and pushing them out via ARD. I suggest you use LanREV's InstallEase (Free) to package up the updated files on your master build system and deploy those packages.

I have a WRT54G v8.1. I upgraded the firmware, and now it DOES NOT WORK.

I have a WRT54G v8.1. I upgraded the firmware, and now it DOES NOT WORK. It keeps telling me that this router is not supported. There is no firmware to roll back to. It worked fine until a power outage. HELP!

If your Internet Service Provider is Cable follow this link to configure the router.
If your Internet Service Provider is DSL follow this link to configure the router.

I download the new firmware and now my Internet says its working buy it won't let me do anything?

I download the new firmware and after I download it my Internet will say it is connected but then when I open safari or anything that involves Internet it will say it is not connected?

I download the new firmware and after I download it my Internet will say it is connected but then when I open safari or anything that involves Internet it will say it is not connected?

CURRENT Bluetooth Firmware and Software Version Listings

OK, I'm hoping there is someone out there that can provide me with what should be a relatively simple answer. My current machine is an iMac G5 1.8GHz. (Non-iSight), 2GB RAM, and 1TB hard disk running OS X 10.4.11
I'm curious to know what the current, up--to-date version listings should be for both the bluetooth software as well as the bluetooth firmware as displayed under "Bluetooth" in the System Profiler when selecting "About This Mac".
I've been experiencing some bluetooth "weirdness" lately and before I provide any additional information as to the exact problem, I'd like to know if the firmware and software versions are up-to-date first.
Apple doesn't seem to provide a chart to check against (unless I missed it), and other's on the forum have explained that those specs are "model-specific", making it a bit tricky. to determine. So that's why I listed my machine in hopes that someone can tell me what versions should be appearing.
Thanks in advance!
Ed M.

your phone is clearly hacked (jailbroken). Not only have you voided your warranty with Apple, but you have forfeited your ability to receive any assistance from Apple, including from this forum. Discussion of jailbroken phones is strictly prohibited by the Terms of Use of this forum.
You'll need to search elsewhere for solutions to your problem. Be prepared for the possibility that you have PERMANENTLY disabled your iPhone.

Modern firmware and software version not matching

Hi...I upgraded my software version to 5.0.1 and didn't upgrade the baseband. My current baseband is 2.10.04. Would this cause problems? I didn't update the firmware due to turbo issues.
Recently I'm having some problems of 'NO SIM CARD INSTALLED'. Does unmatching of firmware and software version have to do with this ?

your phone is clearly hacked (jailbroken). Not only have you voided your warranty with Apple, but you have forfeited your ability to receive any assistance from Apple, including from this forum. Discussion of jailbroken phones is strictly prohibited by the Terms of Use of this forum.
You'll need to search elsewhere for solutions to your problem. Be prepared for the possibility that you have PERMANENTLY disabled your iPhone.

TS3694 hi please help me my iphone was stuck at the unknown error 1015 please teach me how to install my current iphone firmware and gave me the link that i need to download thank you

my iphone 3g stuck in the unknonw error 1015 pleasse help me to get back my current firmware and my iphone has stop using since 4 day so please help me \
thanks you all

you have a jailbroken phone, we can't help you here, try the jailbreak websites.

Firmware and Driver of ZEN Micro

I can't find the firmware of ZEN Micro 5gb and the driver to run in Windows Vista Home Premium 32bits, is it possible to give me the link? Thanks!

Finally I got success!
After downloading and?updating the firmware and installing all new drivers available using other PC with XP and a Pen-dri've I resolved the problem of?compatibility with my PC (Vista Home Premium).
Also I updated the Windows Media Player to use it for music transfering into MP3. It works very well!!
Thank you for?your help!

UCS E140S - Broadcom Firmware and GE1/GE2

Similar Messages

Maybe you are looking for