Udev[testing] breaks nvidia driver

When udev-118-2 and initscripts-2008.02-1 were both installed from the testing repro it caused the nvidia driver [nvidia-169.09-2] to continually fail to load when starting Xorg, with kernel26 2.6.24.2-1. There was no problem using the xf86-video-nv-2.1.7-1 driver.
My card is a Nvidia GeForce 7300 GS.
Re-installing both the kernel and the nvidia, nvidia-utils packages did not fix the problem.
Re-installing udev-116-3 and initscripts-2007.11-2 from the core repro allowed for the nvidia video drivers to be loaded as normal.
I am not sure if there is a problem with these packages from testing or if there was something that I needed to do to properly configure the system after having upgraded these two packages. I have not seen any forum posts, bug reports, or wiki articles concerning this problem, beyond the Gentoo wiki suggesting that nvidia and udev do not get along well.
Thank you for your time.
edit: This is on a i686 install
Last edited by ladislaio (2008-02-27 02:28:48)

I have the same issue. Look if the "nvidiafb" module is loaded, if yes the nvidia module can't be load and X fails to start. Normally that shouldn't be loaded at all, but their exists some issues for specific hardware configurations, that's why it is in testing. Look at the arch-dev-public-ml, we are discussing this topic already (the new udev/initscripts and blacklisting).
@darksheen: There is no need to reinstall the whole system. You just to have downgrade udev and initscripts and your problem would be gone.
EDIT: I filed a bug report here: http://bugs.archlinux.org/task/9701
Daniel
Last edited by ise (2008-02-27 06:29:50)

Similar Messages

Laggy performance with Nvidia driver

Greetings,
I am trying to use my nvidia 9800 GTX card with the Nvidia driver in the official repos. I have a dual monitor setup with gnome 3.10 installed. Everything is snappy with the default configurations with the Noveau driver.
A typical extended desktop environment would be preferable. From what I understand from the multihead and multiple monitor sections of the wiki is that twinview or xinerama would accomplish this, but it is mentioned that xinerama does not work for this newer version of the nvidia driver. I used nvidia-settings to set up the monitors in the right location and saved the config file to /etc/X11/xorg.conf.d/10-monitor.conf as suggested in the wiki. I tried making some configuration changes to the tune of the examples in the wiki, but every change I make seems to result in an even buggier or unbootable x server. I scrapped the nvidia driver and installed noveau to test it out, now I'm back to the initial configuration on the nvidia driver.
The display configuration is actually what I want now, but the system feels overly heavy and laggy. Any suggestions?
Here is the output of my (Corrected) most recent xorg log
X.Org X Server 1.14.4
Release Date: 2013-10-31
[ 2.823] X Protocol Version 11, Revision 0
[ 2.823] Build Operating System: Linux 3.11.6-1-ARCH x86_64
[ 2.823] Current Operating System: Linux bigarch 3.12.3-1-ARCH #1 SMP PREEMPT Wed Dec 4 21:45:42 CET 2013 x86_64
[ 2.823] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=8c847ab2-4f0a-4b91-82c8-716aadf0b24c rw quiet
[ 2.823] Build Date: 01 November 2013 05:10:48PM
[ 2.823]
[ 2.823] Current version of pixman: 0.32.4
[ 2.823] Before reporting problems, check [url]http://wiki.x.org[/url]
to make sure that you have the latest version.
[ 2.823] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 2.823] (==) Log file: "/var/log/Xorg.0.log", Time: Sun Dec 8 15:54:59 2013
[ 2.824] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 2.825] (==) No Layout section. Using the first Screen section.
[ 2.825] (==) No screen section available. Using defaults.
[ 2.825] (**) |-->Screen "Default Screen Section" (0)
[ 2.825] (**) | |-->Monitor "<default monitor>"
[ 2.825] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 2.825] (==) Automatically adding devices
[ 2.825] (==) Automatically enabling devices
[ 2.825] (==) Automatically adding GPU devices
[ 2.828] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 2.828] Entry deleted from font path.
[ 2.828] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 2.828] Entry deleted from font path.
[ 2.828] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 2.828] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 2.828] Entry deleted from font path.
[ 2.828] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 2.828] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 2.828] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 2.828] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 2.828] (II) Loader magic: 0x7fdc20
[ 2.828] (II) Module ABI versions:
[ 2.828] X.Org ANSI C Emulation: 0.4
[ 2.829] X.Org Video Driver: 14.1
[ 2.829] X.Org XInput driver : 19.1
[ 2.829] X.Org Server Extension : 7.0
[ 2.830] (--) PCI:*(0:1:0:0) 10de:0612:10de:0577 rev 162, Mem @ 0xfd000000/16777216, 0xd0000000/268435456, 0xfa000000/33554432, I/O @ 0x0000cc00/128, BIOS @ 0x????????/131072
[ 2.830] Initializing built-in extension Generic Event Extension
[ 2.830] Initializing built-in extension SHAPE
[ 2.830] Initializing built-in extension MIT-SHM
[ 2.830] Initializing built-in extension XInputExtension
[ 2.830] Initializing built-in extension XTEST
[ 2.830] Initializing built-in extension BIG-REQUESTS
[ 2.830] Initializing built-in extension SYNC
[ 2.830] Initializing built-in extension XKEYBOARD
[ 2.830] Initializing built-in extension XC-MISC
[ 2.830] Initializing built-in extension SECURITY
[ 2.830] Initializing built-in extension XINERAMA
[ 2.830] Initializing built-in extension XFIXES
[ 2.830] Initializing built-in extension RENDER
[ 2.830] Initializing built-in extension RANDR
[ 2.830] Initializing built-in extension COMPOSITE
[ 2.830] Initializing built-in extension DAMAGE
[ 2.830] Initializing built-in extension MIT-SCREEN-SAVER
[ 2.830] Initializing built-in extension DOUBLE-BUFFER
[ 2.830] Initializing built-in extension RECORD
[ 2.830] Initializing built-in extension DPMS
[ 2.830] Initializing built-in extension X-Resource
[ 2.830] Initializing built-in extension XVideo
[ 2.830] Initializing built-in extension XVideo-MotionCompensation
[ 2.830] Initializing built-in extension XFree86-VidModeExtension
[ 2.830] Initializing built-in extension XFree86-DGA
[ 2.830] Initializing built-in extension XFree86-DRI
[ 2.830] Initializing built-in extension DRI2
[ 2.830] (II) LoadModule: "glx"
[ 2.833] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 2.835] (II) Module glx: vendor="X.Org Foundation"
[ 2.835] compiled for 1.14.4, module version = 1.0.0
[ 2.835] ABI class: X.Org Server Extension, version 7.0
[ 2.835] (==) AIGLX enabled
[ 2.835] Loading extension GLX
[ 2.835] (==) Matched nouveau as autoconfigured driver 0
[ 2.835] (==) Matched nvidia as autoconfigured driver 1
[ 2.835] (==) Matched nv as autoconfigured driver 2
[ 2.835] (==) Matched vesa as autoconfigured driver 3
[ 2.835] (==) Matched modesetting as autoconfigured driver 4
[ 2.835] (==) Matched fbdev as autoconfigured driver 5
[ 2.836] (==) Assigned the driver to the xf86ConfigLayout
[ 2.836] (II) LoadModule: "nouveau"
[ 2.836] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[ 2.838] (II) Module nouveau: vendor="X.Org Foundation"
[ 2.838] compiled for 1.14.4, module version = 1.0.10
[ 2.838] Module class: X.Org Video Driver
[ 2.838] ABI class: X.Org Video Driver, version 14.1
[ 2.838] (II) LoadModule: "nvidia"
[ 2.839] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 2.848] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 2.848] compiled for 4.0.2, module version = 1.0.0
[ 2.848] Module class: X.Org Video Driver
[ 2.849] (II) LoadModule: "nv"
[ 2.851] (WW) Warning, couldn't open module nv
[ 2.851] (II) UnloadModule: "nv"
[ 2.851] (II) Unloading nv
[ 2.851] (EE) Failed to load module "nv" (module does not exist, 0)
[ 2.851] (II) LoadModule: "vesa"
[ 2.851] (WW) Warning, couldn't open module vesa
[ 2.851] (II) UnloadModule: "vesa"
[ 2.852] (II) Unloading vesa
[ 2.852] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 2.852] (II) LoadModule: "modesetting"
[ 2.852] (WW) Warning, couldn't open module modesetting
[ 2.852] (II) UnloadModule: "modesetting"
[ 2.852] (II) Unloading modesetting
[ 2.852] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 2.852] (II) LoadModule: "fbdev"
[ 2.852] (WW) Warning, couldn't open module fbdev
[ 2.852] (II) UnloadModule: "fbdev"
[ 2.852] (II) Unloading fbdev
[ 2.852] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 2.852] (II) NOUVEAU driver
[ 2.852] (II) NOUVEAU driver for NVIDIA chipset families :
[ 2.852] RIVA TNT (NV04)
[ 2.852] RIVA TNT2 (NV05)
[ 2.852] GeForce 256 (NV10)
[ 2.852] GeForce 2 (NV11, NV15)
[ 2.852] GeForce 4MX (NV17, NV18)
[ 2.852] GeForce 3 (NV20)
[ 2.852] GeForce 4Ti (NV25, NV28)
[ 2.852] GeForce FX (NV3x)
[ 2.852] GeForce 6 (NV4x)
[ 2.852] GeForce 7 (G7x)
[ 2.853] GeForce 8 (G8x)
[ 2.853] GeForce GTX 200 (NVA0)
[ 2.853] GeForce GTX 400 (NVC0)
[ 2.853] (II) NVIDIA dlloader X Driver 331.20 Wed Oct 30 17:16:53 PDT 2013
[ 2.853] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 2.853] (++) using VT number 1
[ 2.853] (EE) [drm] KMS not enabled
[ 2.855] (II) Loading sub module "fb"
[ 2.855] (II) LoadModule: "fb"
[ 2.855] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 2.856] (II) Module fb: vendor="X.Org Foundation"
[ 2.856] compiled for 1.14.4, module version = 1.0.0
[ 2.856] ABI class: X.Org ANSI C Emulation, version 0.4
[ 2.856] (WW) Unresolved symbol: fbGetGCPrivateKey
[ 2.856] (II) Loading sub module "wfb"
[ 2.856] (II) LoadModule: "wfb"
[ 2.856] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 2.858] (II) Module wfb: vendor="X.Org Foundation"
[ 2.858] compiled for 1.14.4, module version = 1.0.0
[ 2.858] ABI class: X.Org ANSI C Emulation, version 0.4
[ 2.858] (II) Loading sub module "ramdac"
[ 2.858] (II) LoadModule: "ramdac"
[ 2.858] (II) Module "ramdac" already built-in
[ 3.013] (II) NVIDIA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 3.013] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[ 3.013] (==) NVIDIA(0): RGB weight 888
[ 3.013] (==) NVIDIA(0): Default visual is TrueColor
[ 3.014] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 3.014] (**) NVIDIA(0): Enabling 2D acceleration
[ 3.014] (EE) NVIDIA(0): Failed to initialize the GLX module; please check in your X
[ 3.014] (EE) NVIDIA(0): log file that the GLX module has been loaded in your X
[ 3.014] (EE) NVIDIA(0): server, and that the module is the NVIDIA GLX module. If
[ 3.014] (EE) NVIDIA(0): you continue to encounter problems, Please try
[ 3.014] (EE) NVIDIA(0): reinstalling the NVIDIA driver.
[ 3.876] (II) NVIDIA(0): Display (Acer AL2216W (CRT-1)) does not support NVIDIA 3D
[ 3.876] (II) NVIDIA(0): Vision stereo.
[ 3.918] (II) NVIDIA(0): Display (Ancor Communications Inc ASUS VH242H (DFP-0)) does
[ 3.918] (II) NVIDIA(0): not support NVIDIA 3D Vision stereo.
[ 3.919] (II) NVIDIA(GPU-0): Found DRM driver nvidia-drm (20130102)
[ 3.919] (II) NVIDIA(0): NVIDIA GPU GeForce 9800 GTX/9800 GTX+ (G92) at PCI:1:0:0
[ 3.919] (II) NVIDIA(0): (GPU-0)
[ 3.919] (--) NVIDIA(0): Memory: 524288 kBytes
[ 3.919] (--) NVIDIA(0): VideoBIOS: 62.92.40.00.07
[ 3.919] (II) NVIDIA(0): Detected PCI Express Link width: 16X
[ 3.923] (--) NVIDIA(0): Valid display device(s) on GeForce 9800 GTX/9800 GTX+ at PCI:1:0:0
[ 3.923] (--) NVIDIA(0): CRT-0
[ 3.923] (--) NVIDIA(0): Acer AL2216W (CRT-1) (connected)
[ 3.923] (--) NVIDIA(0): TV-0
[ 3.923] (--) NVIDIA(0): Ancor Communications Inc ASUS VH242H (DFP-0) (boot, connected)
[ 3.923] (--) NVIDIA(0): DFP-1
[ 3.923] (--) NVIDIA(0): CRT-0: 400.0 MHz maximum pixel clock
[ 3.923] (--) NVIDIA(0): Acer AL2216W (CRT-1): 400.0 MHz maximum pixel clock
[ 3.923] (--) NVIDIA(0): TV-0: 400.0 MHz maximum pixel clock
[ 3.923] (--) NVIDIA(0): Ancor Communications Inc ASUS VH242H (DFP-0): Internal Dual Link TMDS
[ 3.923] (--) NVIDIA(0): Ancor Communications Inc ASUS VH242H (DFP-0): 330.0 MHz maximum pixel clock
[ 3.923] (--) NVIDIA(0): DFP-1: Internal Single Link TMDS
[ 3.923] (--) NVIDIA(0): DFP-1: 330.0 MHz maximum pixel clock
[ 3.923] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
[ 3.923] (**) NVIDIA(0): device Acer AL2216W (CRT-1) (Using EDID frequencies has
[ 3.923] (**) NVIDIA(0): been enabled on all display devices.)
[ 3.924] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
[ 3.924] (**) NVIDIA(0): device Ancor Communications Inc ASUS VH242H (DFP-0) (Using
[ 3.924] (**) NVIDIA(0): EDID frequencies has been enabled on all display
[ 3.924] (**) NVIDIA(0): devices.)
[ 3.926] (==) NVIDIA(0):
[ 3.926] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
[ 3.926] (==) NVIDIA(0): will be used as the requested mode.
[ 3.926] (==) NVIDIA(0):
[ 3.926] (II) NVIDIA(0): Validated MetaModes:
[ 3.926] (II) NVIDIA(0): "DFP-0:nvidia-auto-select,CRT-1:nvidia-auto-select"
[ 3.926] (II) NVIDIA(0): Virtual screen size determined to be 3600 x 1080
[ 3.959] (--) NVIDIA(0): DPI set to (93, 94); computed from "UseEdidDpi" X config
[ 3.960] (--) NVIDIA(0): option
[ 3.960] (--) Depth 24 pixmap format is 32 bpp
[ 3.960] (II) NVIDIA: Using 768.00 MB of virtual memory for indirect memory access.
[ 3.962] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[ 3.962] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
[ 3.962] (II) NVIDIA(0): configuration option may not be set correctly. When the
[ 3.962] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
[ 3.962] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
[ 3.962] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
[ 3.962] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
[ 3.962] (II) NVIDIA(0): Config Options in the README.
[ 3.965] (II) NVIDIA(0): Setting mode "DFP-0:nvidia-auto-select,CRT-1:nvidia-auto-select"
[ 4.022] Loading extension NV-GLX
[ 4.056] (==) NVIDIA(0): Disabling shared memory pixmaps
[ 4.056] (==) NVIDIA(0): Backing store disabled
[ 4.056] (==) NVIDIA(0): Silken mouse enabled
[ 4.057] (==) NVIDIA(0): DPMS enabled
[ 4.057] Loading extension NV-CONTROL
[ 4.057] Loading extension XINERAMA
[ 4.057] (II) Loading sub module "dri2"
[ 4.057] (II) LoadModule: "dri2"
[ 4.057] (II) Module "dri2" already built-in
[ 4.057] (II) NVIDIA(0): [DRI2] Setup complete
[ 4.057] (II) NVIDIA(0): [DRI2] VDPAU driver: nvidia
[ 4.057] (--) RandR disabled
[ 4.062] (II) AIGLX: Screen 0 is not DRI2 capable
[ 4.062] (II) AIGLX: Screen 0 is not DRI capable
[ 4.135] (II) AIGLX: Loaded and initialized swrast
[ 4.135] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[ 4.191] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 4.191] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 4.192] (II) LoadModule: "evdev"
[ 4.192] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 4.193] (II) Module evdev: vendor="X.Org Foundation"
[ 4.193] compiled for 1.14.3, module version = 2.8.2
[ 4.193] Module class: X.Org XInput Driver
[ 4.193] ABI class: X.Org XInput driver, version 19.1
[ 4.193] (II) Using input driver 'evdev' for 'Power Button'
[ 4.193] (**) Power Button: always reports core events
[ 4.193] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 4.193] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 4.193] (--) evdev: Power Button: Found keys
[ 4.193] (II) evdev: Power Button: Configuring as keyboard
[ 4.193] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event1"
[ 4.193] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 4.193] (**) Option "xkb_rules" "evdev"
[ 4.193] (**) Option "xkb_model" "pc104"
[ 4.193] (**) Option "xkb_layout" "us"
[ 4.216] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[ 4.216] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 4.216] (II) Using input driver 'evdev' for 'Power Button'
[ 4.216] (**) Power Button: always reports core events
[ 4.216] (**) evdev: Power Button: Device: "/dev/input/event0"
[ 4.216] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 4.216] (--) evdev: Power Button: Found keys
[ 4.216] (II) evdev: Power Button: Configuring as keyboard
[ 4.216] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event0"
[ 4.216] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 4.216] (**) Option "xkb_rules" "evdev"
[ 4.216] (**) Option "xkb_model" "pc104"
[ 4.216] (**) Option "xkb_layout" "us"
[ 4.216] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 4.216] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 4.216] setversion 1.4 failed
[ 4.217] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event3)
[ 4.217] (II) No input driver specified, ignoring this device.
[ 4.217] (II) This device may have been added with another device file.
[ 4.217] (II) config/udev: Adding input device HDA Intel Line Out CLFE (/dev/input/event6)
[ 4.217] (II) No input driver specified, ignoring this device.
[ 4.217] (II) This device may have been added with another device file.
[ 4.217] (II) config/udev: Adding input device HDA Intel Line Out Side (/dev/input/event5)
[ 4.217] (II) No input driver specified, ignoring this device.
[ 4.217] (II) This device may have been added with another device file.
[ 4.217] (II) config/udev: Adding input device HDA Intel Front Headphone (/dev/input/event4)
[ 4.217] (II) No input driver specified, ignoring this device.
[ 4.217] (II) This device may have been added with another device file.
[ 4.217] (II) config/udev: Adding input device HDA Intel Front Mic (/dev/input/event11)
[ 4.217] (II) No input driver specified, ignoring this device.
[ 4.218] (II) This device may have been added with another device file.
[ 4.218] (II) config/udev: Adding input device HDA Intel Rear Mic (/dev/input/event10)
[ 4.218] (II) No input driver specified, ignoring this device.
[ 4.218] (II) This device may have been added with another device file.
[ 4.218] (II) config/udev: Adding input device HDA Intel Line (/dev/input/event9)
[ 4.218] (II) No input driver specified, ignoring this device.
[ 4.218] (II) This device may have been added with another device file.
[ 4.218] (II) config/udev: Adding input device HDA Intel Line Out Front (/dev/input/event8)
[ 4.218] (II) No input driver specified, ignoring this device.
[ 4.218] (II) This device may have been added with another device file.
[ 4.218] (II) config/udev: Adding input device HDA Intel Line Out Surround (/dev/input/event7)
[ 4.218] (II) No input driver specified, ignoring this device.
[ 4.218] (II) This device may have been added with another device file.
[ 4.219] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:101a (/dev/input/event13)
[ 4.219] (**) Logitech Unifying Device. Wireless PID:101a: Applying InputClass "evdev pointer catchall"
[ 4.219] (II) Using input driver 'evdev' for 'Logitech Unifying Device. Wireless PID:101a'
[ 4.219] (**) Logitech Unifying Device. Wireless PID:101a: always reports core events
[ 4.219] (**) evdev: Logitech Unifying Device. Wireless PID:101a: Device: "/dev/input/event13"
[ 4.219] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Vendor 0x46d Product 0xc52b
[ 4.219] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found 20 mouse buttons
[ 4.219] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found scroll wheel(s)
[ 4.219] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found relative axes
[ 4.219] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found x and y relative axes
[ 4.219] (II) evdev: Logitech Unifying Device. Wireless PID:101a: Configuring as mouse
[ 4.219] (II) evdev: Logitech Unifying Device. Wireless PID:101a: Adding scrollwheel support
[ 4.219] (**) evdev: Logitech Unifying Device. Wireless PID:101a: YAxisMapping: buttons 4 and 5
[ 4.219] (**) evdev: Logitech Unifying Device. Wireless PID:101a: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 4.219] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.2/usb9/9-1/9-1:1.2/0003:046D:C52B.0003/input/input14/event13"
[ 4.219] (II) XINPUT: Adding extended input device "Logitech Unifying Device. Wireless PID:101a" (type: MOUSE, id 8)
[ 4.219] (II) evdev: Logitech Unifying Device. Wireless PID:101a: initialized for relative axes.
[ 4.220] (**) Logitech Unifying Device. Wireless PID:101a: (accel) keeping acceleration scheme 1
[ 4.220] (**) Logitech Unifying Device. Wireless PID:101a: (accel) acceleration profile 0
[ 4.220] (**) Logitech Unifying Device. Wireless PID:101a: (accel) acceleration factor: 2.000
[ 4.220] (**) Logitech Unifying Device. Wireless PID:101a: (accel) acceleration threshold: 4
[ 4.220] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:101a (/dev/input/mouse0)
[ 4.220] (II) No input driver specified, ignoring this device.
[ 4.220] (II) This device may have been added with another device file.
[ 4.220] (II) config/udev: Adding input device Microsoft Comfort Curve Keyboard 2000 (/dev/input/event12)
[ 4.220] (**) Microsoft Comfort Curve Keyboard 2000: Applying InputClass "evdev keyboard catchall"
[ 4.220] (II) Using input driver 'evdev' for 'Microsoft Comfort Curve Keyboard 2000'
[ 4.220] (**) Microsoft Comfort Curve Keyboard 2000: always reports core events
[ 4.220] (**) evdev: Microsoft Comfort Curve Keyboard 2000: Device: "/dev/input/event12"
[ 4.220] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Vendor 0x45e Product 0xdd
[ 4.220] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found keys
[ 4.220] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Configuring as keyboard
[ 4.220] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.2/usb9/9-2/9-2:1.0/input/input13/event12"
[ 4.220] (II) XINPUT: Adding extended input device "Microsoft Comfort Curve Keyboard 2000" (type: KEYBOARD, id 9)
[ 4.220] (**) Option "xkb_rules" "evdev"
[ 4.220] (**) Option "xkb_model" "pc104"
[ 4.220] (**) Option "xkb_layout" "us"
[ 4.221] (II) config/udev: Adding input device Microsoft Comfort Curve Keyboard 2000 (/dev/input/event14)
[ 4.221] (**) Microsoft Comfort Curve Keyboard 2000: Applying InputClass "evdev keyboard catchall"
[ 4.221] (II) Using input driver 'evdev' for 'Microsoft Comfort Curve Keyboard 2000'
[ 4.221] (**) Microsoft Comfort Curve Keyboard 2000: always reports core events
[ 4.221] (**) evdev: Microsoft Comfort Curve Keyboard 2000: Device: "/dev/input/event14"
[ 4.221] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Vendor 0x45e Product 0xdd
[ 4.221] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found 1 mouse buttons
[ 4.221] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found scroll wheel(s)
[ 4.221] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found relative axes
[ 4.221] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Forcing relative x/y axes to exist.
[ 4.221] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found absolute axes
[ 4.221] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Forcing absolute x/y axes to exist.
[ 4.221] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found keys
[ 4.221] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Configuring as mouse
[ 4.221] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Configuring as keyboard
[ 4.221] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Adding scrollwheel support
[ 4.221] (**) evdev: Microsoft Comfort Curve Keyboard 2000: YAxisMapping: buttons 4 and 5
[ 4.221] (**) evdev: Microsoft Comfort Curve Keyboard 2000: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 4.221] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.2/usb9/9-2/9-2:1.1/input/input15/event14"
[ 4.221] (II) XINPUT: Adding extended input device "Microsoft Comfort Curve Keyboard 2000" (type: KEYBOARD, id 10)
[ 4.221] (**) Option "xkb_rules" "evdev"
[ 4.221] (**) Option "xkb_model" "pc104"
[ 4.221] (**) Option "xkb_layout" "us"
[ 4.221] (II) evdev: Microsoft Comfort Curve Keyboard 2000: initialized for relative axes.
[ 4.221] (WW) evdev: Microsoft Comfort Curve Keyboard 2000: ignoring absolute axes.
[ 4.221] (**) Microsoft Comfort Curve Keyboard 2000: (accel) keeping acceleration scheme 1
[ 4.221] (**) Microsoft Comfort Curve Keyboard 2000: (accel) acceleration profile 0
[ 4.221] (**) Microsoft Comfort Curve Keyboard 2000: (accel) acceleration factor: 2.000
[ 4.221] (**) Microsoft Comfort Curve Keyboard 2000: (accel) acceleration threshold: 4
[ 4.222] (II) config/udev: Adding input device UVC Camera (046d:081b) (/dev/input/event15)
[ 4.222] (**) UVC Camera (046d:081b): Applying InputClass "evdev keyboard catchall"
[ 4.222] (II) Using input driver 'evdev' for 'UVC Camera (046d:081b)'
[ 4.222] (**) UVC Camera (046d:081b): always reports core events
[ 4.222] (**) evdev: UVC Camera (046d:081b): Device: "/dev/input/event15"
[ 4.222] (--) evdev: UVC Camera (046d:081b): Vendor 0x46d Product 0x81b
[ 4.222] (--) evdev: UVC Camera (046d:081b): Found keys
[ 4.222] (II) evdev: UVC Camera (046d:081b): Configuring as keyboard
[ 4.222] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.7/usb10/10-3/10-3:1.0/input/input16/event15"
[ 4.222] (II) XINPUT: Adding extended input device "UVC Camera (046d:081b)" (type: KEYBOARD, id 11)
[ 4.222] (**) Option "xkb_rules" "evdev"
[ 4.222] (**) Option "xkb_model" "pc104"
[ 4.222] (**) Option "xkb_layout" "us"
[ 4.222] (II) config/udev: Adding input device PC Speaker (/dev/input/event2)
[ 4.222] (II) No input driver specified, ignoring this device.
[ 4.222] (II) This device may have been added with another device file.
[ 4.225] (II) config/udev: removing device Microsoft Comfort Curve Keyboard 2000
[ 4.250] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Close
[ 4.250] (II) UnloadModule: "evdev"
[ 4.250] (II) config/udev: Adding input device Microsoft Comfort Curve Keyboard 2000 (/dev/input/event12)
[ 4.250] (**) Microsoft Comfort Curve Keyboard 2000: Applying InputClass "evdev keyboard catchall"
[ 4.250] (II) Using input driver 'evdev' for 'Microsoft Comfort Curve Keyboard 2000'
[ 4.250] (**) Microsoft Comfort Curve Keyboard 2000: always reports core events
[ 4.250] (**) evdev: Microsoft Comfort Curve Keyboard 2000: Device: "/dev/input/event12"
[ 4.250] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Vendor 0x45e Product 0xdd
[ 4.250] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found keys
[ 4.250] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Configuring as keyboard
[ 4.250] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.2/usb9/9-2/9-2:1.0/input/input13/event12"
[ 4.250] (II) XINPUT: Adding extended input device "Microsoft Comfort Curve Keyboard 2000" (type: KEYBOARD, id 9)
[ 4.250] (**) Option "xkb_rules" "evdev"
[ 4.250] (**) Option "xkb_model" "pc104"
[ 4.250] (**) Option "xkb_layout" "us"
[ 4.250] (II) config/udev: removing device Logitech Unifying Device. Wireless PID:101a
[ 4.276] (II) evdev: Logitech Unifying Device. Wireless PID:101a: Close
[ 4.276] (II) UnloadModule: "evdev"
[ 4.276] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:101a (/dev/input/event13)
[ 4.276] (**) Logitech Unifying Device. Wireless PID:101a: Applying InputClass "evdev pointer catchall"
[ 4.276] (II) Using input driver 'evdev' for 'Logitech Unifying Device. Wireless PID:101a'
[ 4.276] (**) Logitech Unifying Device. Wireless PID:101a: always reports core events
[ 4.276] (**) evdev: Logitech Unifying Device. Wireless PID:101a: Device: "/dev/input/event13"
[ 4.276] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Vendor 0x46d Product 0xc52b
[ 4.277] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found 20 mouse buttons
[ 4.277] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found scroll wheel(s)
[ 4.277] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found relative axes
[ 4.277] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found x and y relative axes
[ 4.277] (II) evdev: Logitech Unifying Device. Wireless PID:101a: Configuring as mouse
[ 4.277] (II) evdev: Logitech Unifying Device. Wireless PID:101a: Adding scrollwheel support
[ 4.277] (**) evdev: Logitech Unifying Device. Wireless PID:101a: YAxisMapping: buttons 4 and 5
[ 4.277] (**) evdev: Logitech Unifying Device. Wireless PID:101a: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 4.277] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.2/usb9/9-1/9-1:1.2/0003:046D:C52B.0003/input/input14/event13"
[ 4.277] (II) XINPUT: Adding extended input device "Logitech Unifying Device. Wireless PID:101a" (type: MOUSE, id 8)
[ 4.277] (II) evdev: Logitech Unifying Device. Wireless PID:101a: initialized for relative axes.
[ 4.277] (**) Logitech Unifying Device. Wireless PID:101a: (accel) keeping acceleration scheme 1
[ 4.277] (**) Logitech Unifying Device. Wireless PID:101a: (accel) acceleration profile 0
[ 4.277] (**) Logitech Unifying Device. Wireless PID:101a: (accel) acceleration factor: 2.000
[ 4.277] (**) Logitech Unifying Device. Wireless PID:101a: (accel) acceleration threshold: 4
[ 4.277] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:101a (/dev/input/mouse0)
[ 4.277] (II) No input driver specified, ignoring this device.
[ 4.277] (II) This device may have been added with another device file.
[ 4.277] (II) config/udev: removing device Microsoft Comfort Curve Keyboard 2000
[ 4.303] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Close
[ 4.303] (II) UnloadModule: "evdev"
[ 4.303] (II) config/udev: Adding input device Microsoft Comfort Curve Keyboard 2000 (/dev/input/event14)
[ 4.303] (**) Microsoft Comfort Curve Keyboard 2000: Applying InputClass "evdev keyboard catchall"
[ 4.303] (II) Using input driver 'evdev' for 'Microsoft Comfort Curve Keyboard 2000'
[ 4.303] (**) Microsoft Comfort Curve Keyboard 2000: always reports core events
[ 4.303] (**) evdev: Microsoft Comfort Curve Keyboard 2000: Device: "/dev/input/event14"
[ 4.303] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Vendor 0x45e Product 0xdd
[ 4.303] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found 1 mouse buttons
[ 4.303] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found scroll wheel(s)
[ 4.303] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found relative axes
[ 4.303] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Forcing relative x/y axes to exist.
[ 4.303] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found absolute axes
[ 4.303] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Forcing absolute x/y axes to exist.
[ 4.303] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found keys
[ 4.303] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Configuring as mouse
[ 4.303] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Configuring as keyboard
[ 4.303] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Adding scrollwheel support
[ 4.303] (**) evdev: Microsoft Comfort Curve Keyboard 2000: YAxisMapping: buttons 4 and 5
[ 4.303] (**) evdev: Microsoft Comfort Curve Keyboard 2000: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 4.303] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.2/usb9/9-2/9-2:1.1/input/input15/event14"
[ 4.303] (II) XINPUT: Adding extended input device "Microsoft Comfort Curve Keyboard 2000" (type: KEYBOARD, id 10)
[ 4.303] (**) Option "xkb_rules" "evdev"
[ 4.303] (**) Option "xkb_model" "pc104"
[ 4.303] (**) Option "xkb_layout" "us"
[ 4.304] (II) evdev: Microsoft Comfort Curve Keyboard 2000: initialized for relative axes.
[ 4.304] (WW) evdev: Microsoft Comfort Curve Keyboard 2000: ignoring absolute axes.
[ 4.304] (**) Microsoft Comfort Curve Keyboard 2000: (accel) keeping acceleration scheme 1
[ 4.304] (**) Microsoft Comfort Curve Keyboard 2000: (accel) acceleration profile 0
[ 4.304] (**) Microsoft Comfort Curve Keyboard 2000: (accel) acceleration factor: 2.000
[ 4.304] (**) Microsoft Comfort Curve Keyboard 2000: (accel) acceleration threshold: 4
[ 4.304] removing GPU device /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0 /dev/dri/card0
[ 4.304] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 4.304] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 4.304] setversion 1.4 failed
[ 4.304] (II) config/udev: removing device UVC Camera (046d:081b)
[ 4.330] (II) evdev: UVC Camera (046d:081b): Close
[ 4.330] (II) UnloadModule: "evdev"
[ 4.330] (II) config/udev: Adding input device UVC Camera (046d:081b) (/dev/input/event15)
[ 4.330] (**) UVC Camera (046d:081b): Applying InputClass "evdev keyboard catchall"
[ 4.330] (II) Using input driver 'evdev' for 'UVC Camera (046d:081b)'
[ 4.330] (**) UVC Camera (046d:081b): always reports core events
[ 4.330] (**) evdev: UVC Camera (046d:081b): Device: "/dev/input/event15"
[ 4.330] (--) evdev: UVC Camera (046d:081b): Vendor 0x46d Product 0x81b
[ 4.330] (--) evdev: UVC Camera (046d:081b): Found keys
[ 4.330] (II) evdev: UVC Camera (046d:081b): Configuring as keyboard
[ 4.330] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.7/usb10/10-3/10-3:1.0/input/input16/event15"
[ 4.330] (II) XINPUT: Adding extended input device "UVC Camera (046d:081b)" (type: KEYBOARD, id 11)
[ 4.330] (**) Option "xkb_rules" "evdev"
[ 4.330] (**) Option "xkb_model" "pc104"
[ 4.330] (**) Option "xkb_layout" "us"
[ 5.323] (II) NVIDIA(GPU-0): Display (Acer AL2216W (CRT-1)) does not support NVIDIA 3D
[ 5.323] (II) NVIDIA(GPU-0): Vision stereo.
[ 5.364] (II) NVIDIA(GPU-0): Display (Ancor Communications Inc ASUS VH242H (DFP-0)) does
[ 5.364] (II) NVIDIA(GPU-0): not support NVIDIA 3D Vision stereo.
[ 5.690] (II) NVIDIA(0): Setting mode "DVI-I-1: nvidia-auto-select @1680x1050 +1920+0 {ViewPortIn=1680x1050, ViewPortOut=1680x1050+0+0}"
[ 5.805] (II) NVIDIA(0): Setting mode "DVI-I-2: nvidia-auto-select @1920x1080 +0+0 {ViewPortIn=1920x1080, ViewPortOut=1920x1080+0+0}, DVI-I-1: nvidia-auto-select @1680x1050 +1920+0 {ViewPortIn=1680x1050, ViewPortOut=1680x1050+0+0}"
[ 6.374] (II) NVIDIA(GPU-0): Display (Acer AL2216W (CRT-1)) does not support NVIDIA 3D
[ 6.374] (II) NVIDIA(GPU-0): Vision stereo.
[ 6.415] (II) NVIDIA(GPU-0): Display (Ancor Communications Inc ASUS VH242H (DFP-0)) does
[ 6.415] (II) NVIDIA(GPU-0): not support NVIDIA 3D Vision stereo.
[ 16.066] (II) NVIDIA(GPU-0): Display (Acer AL2216W (CRT-1)) does not support NVIDIA 3D
[ 16.066] (II) NVIDIA(GPU-0): Vision stereo.
[ 16.107] (II) NVIDIA(GPU-0): Display (Ancor Communications Inc ASUS VH242H (DFP-0)) does
[ 16.107] (II) NVIDIA(GPU-0): not support NVIDIA 3D Vision stereo.
[ 16.218] (II) NVIDIA(0): Setting mode "DVI-I-1: nvidia-auto-select @1680x1050 +1920+0 {ViewPortIn=1680x1050, ViewPortOut=1680x1050+0+0}"
[ 16.323] (II) NVIDIA(0): Setting mode "DVI-I-2: nvidia-auto-select @1920x1080 +0+0 {ViewPortIn=1920x1080, ViewPortOut=1920x1080+0+0}, DVI-I-1: nvidia-auto-select @1680x1050 +1920+0 {ViewPortIn=1680x1050, ViewPortOut=1680x1050+0+0}"
[ 16.743] (II) NVIDIA(GPU-0): Display (Acer AL2216W (CRT-1)) does not support NVIDIA 3D
[ 16.743] (II) NVIDIA(GPU-0): Vision stereo.
[ 16.784] (II) NVIDIA(GPU-0): Display (Ancor Communications Inc ASUS VH242H (DFP-0)) does
[ 16.784] (II) NVIDIA(GPU-0): not support NVIDIA 3D Vision stereo.
[ 382.257] (II) NVIDIA(GPU-0): Display (Acer AL2216W (CRT-1)) does not support NVIDIA 3D
[ 382.257] (II) NVIDIA(GPU-0): Vision stereo.
[ 382.298] (II) NVIDIA(GPU-0): Display (Ancor Communications Inc ASUS VH242H (DFP-0)) does
[ 382.298] (II) NVIDIA(GPU-0): not support NVIDIA 3D Vision stereo.
[ 406.359] (II) NVIDIA(GPU-0): Display (Acer AL2216W (CRT-1)) does not support NVIDIA 3D
[ 406.359] (II) NVIDIA(GPU-0): Vision stereo.
[ 406.401] (II) NVIDIA(GPU-0): Display (Ancor Communications Inc ASUS VH242H (DFP-0)) does
[ 406.401] (II) NVIDIA(GPU-0): not support NVIDIA 3D Vision stereo.
[ 1133.343] (II) NVIDIA(0): Setting mode "DVI-I-2:nvidia-auto-select{ViewPortIn=1366x768,ViewPortOut=1920x1079+0+0}"
[ 1133.682] (II) NVIDIA(GPU-0): Display (Acer AL2216W (CRT-1)) does not support NVIDIA 3D
[ 1133.682] (II) NVIDIA(GPU-0): Vision stereo.
[ 1133.724] (II) NVIDIA(GPU-0): Display (Ancor Communications Inc ASUS VH242H (DFP-0)) does
[ 1133.724] (II) NVIDIA(GPU-0): not support NVIDIA 3D Vision stereo.
[ 1142.928] (II) NVIDIA(0): Setting mode "DVI-I-2: nvidia-auto-select @1920x1080 +0+0 {ViewPortIn=1920x1080, ViewPortOut=1920x1080+0+0}, DVI-I-1: nvidia-auto-select @1680x1050 +1920+0 {ViewPortIn=1680x1050, ViewPortOut=1680x1050+0+0}"
[ 1143.167] (II) NVIDIA(GPU-0): Display (Acer AL2216W (CRT-1)) does not support NVIDIA 3D
[ 1143.167] (II) NVIDIA(GPU-0): Vision stereo.
[ 1143.209] (II) NVIDIA(GPU-0): Display (Ancor Communications Inc ASUS VH242H (DFP-0)) does
[ 1143.209] (II) NVIDIA(GPU-0): not support NVIDIA 3D Vision stereo.
Last edited by verlyn13 (2013-12-08 23:36:23)

Is it safe to conclude that I did not properly install the nvidia driver since the output in the xorg file shows that nouveau module is being loaded? I am not sure where I went wrong since the wiki says to simply
pacman -S nvidia nvidia-utils
and the nouveau driver will be automatically blacklisted and the nvidia driver installed.
I found this https://wiki.archlinux.org/index.php/NV … au_drivers which provides a script for switching between nvidia and nouveau drivers. It states the scripts may be
out of date and the sed lines not necessary. From what I see there was no "nouveau" module being loaded in /etc/mkinitcpio.conf.
As of now I removed the nvidia and nvidia-utils packages and reinstalled the nouveau driver as described in the wiki. It is quick and stable now, but does not look nearly as nice as it would be with the proprietary drivers. My system was incredibly buggy and unstable with the nvidia drivers installed, which I just don't understand. My keyboard would not work at the login screen, and would complain about mounting some partitions I have in fstab.
Here is the current information from my system:
cat /var/log/Xorg.0.log
X.Org X Server 1.14.4
Release Date: 2013-10-31
[ 3.078] X Protocol Version 11, Revision 0
[ 3.078] Build Operating System: Linux 3.11.6-1-ARCH x86_64
[ 3.078] Current Operating System: Linux bigarch 3.12.3-1-ARCH #1 SMP PREEMPT Wed Dec 4 21:45:42 CET 2013 x86_64
[ 3.078] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=8c847ab2-4f0a-4b91-82c8-716aadf0b24c rw quiet
[ 3.078] Build Date: 01 November 2013 05:10:48PM
[ 3.078]
[ 3.078] Current version of pixman: 0.32.4
[ 3.078] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 3.078] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 3.078] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Dec 9 21:38:25 2013
[ 3.079] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 3.080] (==) No Layout section. Using the first Screen section.
[ 3.080] (==) No screen section available. Using defaults.
[ 3.080] (**) |-->Screen "Default Screen Section" (0)
[ 3.080] (**) | |-->Monitor "<default monitor>"
[ 3.080] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 3.080] (==) Automatically adding devices
[ 3.080] (==) Automatically enabling devices
[ 3.080] (==) Automatically adding GPU devices
[ 3.083] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 3.083] Entry deleted from font path.
[ 3.084] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 3.084] Entry deleted from font path.
[ 3.084] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 3.084] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 3.084] Entry deleted from font path.
[ 3.084] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 3.084] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 3.084] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 3.084] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 3.084] (II) Loader magic: 0x7fdc20
[ 3.084] (II) Module ABI versions:
[ 3.084] X.Org ANSI C Emulation: 0.4
[ 3.084] X.Org Video Driver: 14.1
[ 3.084] X.Org XInput driver : 19.1
[ 3.084] X.Org Server Extension : 7.0
[ 3.084] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 3.086] (--) PCI:*(0:1:0:0) 10de:0612:10de:0577 rev 162, Mem @ 0xfd000000/16777216, 0xd0000000/268435456, 0xfa000000/33554432, I/O @ 0x0000cc00/128, BIOS @ 0x????????/131072
[ 3.086] Initializing built-in extension Generic Event Extension
[ 3.086] Initializing built-in extension SHAPE
[ 3.086] Initializing built-in extension MIT-SHM
[ 3.086] Initializing built-in extension XInputExtension
[ 3.086] Initializing built-in extension XTEST
[ 3.086] Initializing built-in extension BIG-REQUESTS
[ 3.086] Initializing built-in extension SYNC
[ 3.086] Initializing built-in extension XKEYBOARD
[ 3.086] Initializing built-in extension XC-MISC
[ 3.086] Initializing built-in extension SECURITY
[ 3.086] Initializing built-in extension XINERAMA
[ 3.086] Initializing built-in extension XFIXES
[ 3.086] Initializing built-in extension RENDER
[ 3.086] Initializing built-in extension RANDR
[ 3.086] Initializing built-in extension COMPOSITE
[ 3.086] Initializing built-in extension DAMAGE
[ 3.086] Initializing built-in extension MIT-SCREEN-SAVER
[ 3.086] Initializing built-in extension DOUBLE-BUFFER
[ 3.086] Initializing built-in extension RECORD
[ 3.086] Initializing built-in extension DPMS
[ 3.086] Initializing built-in extension X-Resource
[ 3.086] Initializing built-in extension XVideo
[ 3.086] Initializing built-in extension XVideo-MotionCompensation
[ 3.086] Initializing built-in extension XFree86-VidModeExtension
[ 3.086] Initializing built-in extension XFree86-DGA
[ 3.086] Initializing built-in extension XFree86-DRI
[ 3.086] Initializing built-in extension DRI2
[ 3.086] (II) LoadModule: "glx"
[ 3.089] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 3.091] (II) Module glx: vendor="X.Org Foundation"
[ 3.091] compiled for 1.14.4, module version = 1.0.0
[ 3.092] ABI class: X.Org Server Extension, version 7.0
[ 3.092] (==) AIGLX enabled
[ 3.092] Loading extension GLX
[ 3.092] (==) Matched nouveau as autoconfigured driver 0
[ 3.092] (==) Matched nvidia as autoconfigured driver 1
[ 3.092] (==) Matched nv as autoconfigured driver 2
[ 3.092] (==) Matched nouveau as autoconfigured driver 3
[ 3.092] (==) Matched nvidia as autoconfigured driver 4
[ 3.092] (==) Matched nv as autoconfigured driver 5
[ 3.092] (==) Matched vesa as autoconfigured driver 6
[ 3.092] (==) Matched modesetting as autoconfigured driver 7
[ 3.092] (==) Matched fbdev as autoconfigured driver 8
[ 3.092] (==) Assigned the driver to the xf86ConfigLayout
[ 3.092] (II) LoadModule: "nouveau"
[ 3.093] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[ 3.095] (II) Module nouveau: vendor="X.Org Foundation"
[ 3.095] compiled for 1.14.4, module version = 1.0.10
[ 3.095] Module class: X.Org Video Driver
[ 3.095] ABI class: X.Org Video Driver, version 14.1
[ 3.096] (II) LoadModule: "nvidia"
[ 3.097] (WW) Warning, couldn't open module nvidia
[ 3.097] (II) UnloadModule: "nvidia"
[ 3.097] (II) Unloading nvidia
[ 3.097] (EE) Failed to load module "nvidia" (module does not exist, 0)
[ 3.097] (II) LoadModule: "nv"
[ 3.098] (WW) Warning, couldn't open module nv
[ 3.098] (II) UnloadModule: "nv"
[ 3.098] (II) Unloading nv
[ 3.098] (EE) Failed to load module "nv" (module does not exist, 0)
[ 3.098] (II) LoadModule: "vesa"
[ 3.098] (WW) Warning, couldn't open module vesa
[ 3.098] (II) UnloadModule: "vesa"
[ 3.098] (II) Unloading vesa
[ 3.098] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 3.098] (II) LoadModule: "modesetting"
[ 3.098] (WW) Warning, couldn't open module modesetting
[ 3.098] (II) UnloadModule: "modesetting"
[ 3.098] (II) Unloading modesetting
[ 3.098] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 3.098] (II) LoadModule: "fbdev"
[ 3.098] (WW) Warning, couldn't open module fbdev
[ 3.098] (II) UnloadModule: "fbdev"
[ 3.098] (II) Unloading fbdev
[ 3.098] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 3.098] (II) NOUVEAU driver
[ 3.098] (II) NOUVEAU driver for NVIDIA chipset families :
[ 3.098] RIVA TNT (NV04)
[ 3.098] RIVA TNT2 (NV05)
[ 3.098] GeForce 256 (NV10)
[ 3.098] GeForce 2 (NV11, NV15)
[ 3.098] GeForce 4MX (NV17, NV18)
[ 3.098] GeForce 3 (NV20)
[ 3.098] GeForce 4Ti (NV25, NV28)
[ 3.098] GeForce FX (NV3x)
[ 3.098] GeForce 6 (NV4x)
[ 3.098] GeForce 7 (G7x)
[ 3.099] GeForce 8 (G8x)
[ 3.099] GeForce GTX 200 (NVA0)
[ 3.099] GeForce GTX 400 (NVC0)
[ 3.099] (++) using VT number 1
[ 3.099] (II) [drm] nouveau interface version: 1.1.1
[ 3.099] (II) Loading sub module "dri2"
[ 3.099] (II) LoadModule: "dri2"
[ 3.099] (II) Module "dri2" already built-in
[ 3.099] (--) NOUVEAU(0): Chipset: "NVIDIA NV92"
[ 3.099] (II) NOUVEAU(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 3.099] (==) NOUVEAU(0): Depth 24, (--) framebuffer bpp 32
[ 3.099] (==) NOUVEAU(0): RGB weight 888
[ 3.099] (==) NOUVEAU(0): Default visual is TrueColor
[ 3.099] (==) NOUVEAU(0): Using HW cursor
[ 3.099] (==) NOUVEAU(0): GLX sync to VBlank disabled.
[ 3.099] (==) NOUVEAU(0): Page flipping enabled
[ 3.099] (==) NOUVEAU(0): Swap limit set to 2 [Max allowed 2]
[ 3.136] (II) NOUVEAU(0): Output DVI-I-1 has no monitor section
[ 3.164] (II) NOUVEAU(0): Output DVI-I-2 has no monitor section
[ 3.194] (II) NOUVEAU(0): EDID for output DVI-I-1
[ 3.194] (II) NOUVEAU(0): Manufacturer: ACI Model: 24f3 Serial#: 48640
[ 3.194] (II) NOUVEAU(0): Year: 2010 Week: 49
[ 3.194] (II) NOUVEAU(0): EDID Version: 1.3
[ 3.194] (II) NOUVEAU(0): Digital Display Input
[ 3.194] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 52 vert.: 29
[ 3.194] (II) NOUVEAU(0): Gamma: 2.20
[ 3.194] (II) NOUVEAU(0): DPMS capabilities: Off
[ 3.194] (II) NOUVEAU(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 3.194] (II) NOUVEAU(0): First detailed timing is preferred mode
[ 3.194] (II) NOUVEAU(0): redX: 0.644 redY: 0.332 greenX: 0.286 greenY: 0.601
[ 3.194] (II) NOUVEAU(0): blueX: 0.152 blueY: 0.076 whiteX: 0.312 whiteY: 0.328
[ 3.194] (II) NOUVEAU(0): Supported established timings:
[ 3.194] (II) NOUVEAU(0): 720x400@70Hz
[ 3.194] (II) NOUVEAU(0): 640x480@60Hz
[ 3.194] (II) NOUVEAU(0): 640x480@67Hz
[ 3.194] (II) NOUVEAU(0): 640x480@72Hz
[ 3.194] (II) NOUVEAU(0): 640x480@75Hz
[ 3.194] (II) NOUVEAU(0): 800x600@56Hz
[ 3.194] (II) NOUVEAU(0): 800x600@60Hz
[ 3.194] (II) NOUVEAU(0): 800x600@72Hz
[ 3.194] (II) NOUVEAU(0): 800x600@75Hz
[ 3.194] (II) NOUVEAU(0): 832x624@75Hz
[ 3.194] (II) NOUVEAU(0): 1024x768@60Hz
[ 3.194] (II) NOUVEAU(0): 1024x768@70Hz
[ 3.194] (II) NOUVEAU(0): 1024x768@75Hz
[ 3.194] (II) NOUVEAU(0): 1280x1024@75Hz
[ 3.194] (II) NOUVEAU(0): Manufacturer's mask: 0
[ 3.194] (II) NOUVEAU(0): Supported standard timings:
[ 3.194] (II) NOUVEAU(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 3.194] (II) NOUVEAU(0): #1: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 3.194] (II) NOUVEAU(0): #2: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 3.194] (II) NOUVEAU(0): #3: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 3.194] (II) NOUVEAU(0): #4: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 3.194] (II) NOUVEAU(0): #5: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 3.194] (II) NOUVEAU(0): Supported detailed timing:
[ 3.194] (II) NOUVEAU(0): clock: 148.5 MHz Image Size: 521 x 293 mm
[ 3.194] (II) NOUVEAU(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 3.194] (II) NOUVEAU(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 3.194] (II) NOUVEAU(0): Serial No: ACLMTF048640
[ 3.194] (II) NOUVEAU(0): Ranges: V min: 55 V max: 75 Hz, H min: 30 H max: 85 kHz, PixClock max 165 MHz
[ 3.194] (II) NOUVEAU(0): Monitor name: ASUS VH242H
[ 3.194] (II) NOUVEAU(0): EDID (in hex):
[ 3.194] (II) NOUVEAU(0): 00ffffffffffff000469f32400be0000
[ 3.194] (II) NOUVEAU(0): 3114010380341d782ac720a455499927
[ 3.194] (II) NOUVEAU(0): 135054bfef00714f814081809500b300
[ 3.194] (II) NOUVEAU(0): d1c001010101023a801871382d40582c
[ 3.194] (II) NOUVEAU(0): 450009252100001e000000ff0041434c
[ 3.194] (II) NOUVEAU(0): 4d54463034383634300a000000fd0037
[ 3.194] (II) NOUVEAU(0): 4b1e5510000a202020202020000000fc
[ 3.194] (II) NOUVEAU(0): 0041535553205648323432480a200079
[ 3.194] (II) NOUVEAU(0): Printing probed modes for output DVI-I-1
[ 3.194] (II) NOUVEAU(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 3.194] (II) NOUVEAU(0): Modeline "1680x1050"x59.9 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "1440x900"x59.9 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 3.194] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 3.223] (II) NOUVEAU(0): EDID for output DVI-I-2
[ 3.223] (II) NOUVEAU(0): Manufacturer: ACR Model: ada1 Serial#: 2168464612
[ 3.223] (II) NOUVEAU(0): Year: 2008 Week: 14
[ 3.223] (II) NOUVEAU(0): EDID Version: 1.3
[ 3.223] (II) NOUVEAU(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V
[ 3.223] (II) NOUVEAU(0): Sync: Separate
[ 3.223] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 47 vert.: 30
[ 3.223] (II) NOUVEAU(0): Gamma: 2.20
[ 3.223] (II) NOUVEAU(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
[ 3.223] (II) NOUVEAU(0): First detailed timing is preferred mode
[ 3.223] (II) NOUVEAU(0): redX: 0.640 redY: 0.329 greenX: 0.300 greenY: 0.600
[ 3.223] (II) NOUVEAU(0): blueX: 0.150 blueY: 0.060 whiteX: 0.313 whiteY: 0.329
[ 3.223] (II) NOUVEAU(0): Supported established timings:
[ 3.223] (II) NOUVEAU(0): 720x400@70Hz
[ 3.223] (II) NOUVEAU(0): 640x480@60Hz
[ 3.223] (II) NOUVEAU(0): 640x480@67Hz
[ 3.223] (II) NOUVEAU(0): 640x480@72Hz
[ 3.223] (II) NOUVEAU(0): 640x480@75Hz
[ 3.223] (II) NOUVEAU(0): 800x600@56Hz
[ 3.223] (II) NOUVEAU(0): 800x600@60Hz
[ 3.223] (II) NOUVEAU(0): 800x600@72Hz
[ 3.223] (II) NOUVEAU(0): 800x600@75Hz
[ 3.223] (II) NOUVEAU(0): 832x624@75Hz
[ 3.223] (II) NOUVEAU(0): 1024x768@60Hz
[ 3.223] (II) NOUVEAU(0): 1024x768@70Hz
[ 3.223] (II) NOUVEAU(0): 1024x768@75Hz
[ 3.223] (II) NOUVEAU(0): 1280x1024@75Hz
[ 3.223] (II) NOUVEAU(0): 1152x864@75Hz
[ 3.223] (II) NOUVEAU(0): Manufacturer's mask: 10
[ 3.223] (II) NOUVEAU(0): Supported standard timings:
[ 3.223] (II) NOUVEAU(0): #0: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 3.223] (II) NOUVEAU(0): #1: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 3.223] (II) NOUVEAU(0): #2: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 3.223] (II) NOUVEAU(0): #3: hsize: 1360 vsize 765 refresh: 60 vid: 49291
[ 3.223] (II) NOUVEAU(0): #4: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 3.223] (II) NOUVEAU(0): #5: hsize: 1440 vsize 900 refresh: 75 vid: 3989
[ 3.223] (II) NOUVEAU(0): #6: hsize: 1400 vsize 1050 refresh: 60 vid: 16528
[ 3.223] (II) NOUVEAU(0): Supported detailed timing:
[ 3.223] (II) NOUVEAU(0): clock: 146.2 MHz Image Size: 474 x 296 mm
[ 3.223] (II) NOUVEAU(0): h_active: 1680 h_sync: 1784 h_sync_end 1960 h_blank_end 2240 h_border: 0
[ 3.223] (II) NOUVEAU(0): v_active: 1050 v_sync: 1053 v_sync_end 1059 v_blanking: 1089 v_border: 0
[ 3.223] (II) NOUVEAU(0): Ranges: V min: 56 V max: 77 Hz, H min: 31 H max: 84 kHz, PixClock max 175 MHz
[ 3.223] (II) NOUVEAU(0): Serial No: LA10C0414031
[ 3.223] (II) NOUVEAU(0): Monitor name: AL2216W
[ 3.223] (II) NOUVEAU(0): EDID (in hex):
[ 3.223] (II) NOUVEAU(0): 00ffffffffffff000472a1ade4244081
[ 3.223] (II) NOUVEAU(0): 0e120103082f1e78eade95a3544c9926
[ 3.223] (II) NOUVEAU(0): 0f5054bfef90a940714f81408bc09500
[ 3.223] (II) NOUVEAU(0): 950f9040010121399030621a274068b0
[ 3.223] (II) NOUVEAU(0): 3600da2811000019000000fd00384d1f
[ 3.223] (II) NOUVEAU(0): 5411000a202020202020000000ff004c
[ 3.224] (II) NOUVEAU(0): 41313043303431343033310a000000fc
[ 3.224] (II) NOUVEAU(0): 00414c32323136570a20202020200045
[ 3.224] (II) NOUVEAU(0): Printing probed modes for output DVI-I-2
[ 3.224] (II) NOUVEAU(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync -vsync (65.3 kHz eP)
[ 3.224] (II) NOUVEAU(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "1400x1050"x60.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "1440x900"x75.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "1360x768"x59.8 84.75 1366 1431 1567 1776 768 771 781 798 -hsync +vsync (47.7 kHz)
[ 3.224] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 3.224] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 3.224] (II) NOUVEAU(0): Output DVI-I-1 connected
[ 3.224] (II) NOUVEAU(0): Output DVI-I-2 connected
[ 3.224] (II) NOUVEAU(0): Using exact sizes for initial modes
[ 3.224] (II) NOUVEAU(0): Output DVI-I-1 using initial mode 1680x1050
[ 3.224] (II) NOUVEAU(0): Output DVI-I-2 using initial mode 1680x1050
[ 3.224] (II) NOUVEAU(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 3.224] (--) NOUVEAU(0): Virtual size is 1680x1050 (pitch 0)
[ 3.224] (**) NOUVEAU(0): Driver mode "1680x1050": 146.2 MHz (scaled from 0.0 MHz), 65.3 kHz, 60.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync -vsync (65.3 kHz eP)
[ 3.224] (**) NOUVEAU(0): Driver mode "1600x1200": 162.0 MHz (scaled from 0.0 MHz), 75.0 kHz, 60.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "1400x1050": 121.8 MHz (scaled from 0.0 MHz), 65.3 kHz, 60.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1400x1050"x60.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "1280x1024": 135.0 MHz (scaled from 0.0 MHz), 80.0 kHz, 75.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "1440x900": 136.8 MHz (scaled from 0.0 MHz), 70.6 kHz, 75.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1440x900"x75.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "1440x900": 106.5 MHz (scaled from 0.0 MHz), 55.9 kHz, 59.9 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "1280x960": 108.0 MHz (scaled from 0.0 MHz), 60.0 kHz, 60.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 3.224] (**) NOUVEAU(0): Mode "1360x768": 84.8 MHz (scaled from 0.0 MHz), 47.7 kHz, 59.8 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1360x768"x59.8 84.75 1366 1431 1567 1776 768 771 781 798 -hsync +vsync (47.7 kHz)
[ 3.224] (**) NOUVEAU(0): Driver mode "1152x864": 108.0 MHz (scaled from 0.0 MHz), 67.5 kHz, 75.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "1024x768": 78.8 MHz (scaled from 0.0 MHz), 60.1 kHz, 75.1 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "1024x768": 75.0 MHz (scaled from 0.0 MHz), 56.5 kHz, 70.1 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "1024x768": 65.0 MHz (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "832x624": 57.3 MHz (scaled from 0.0 MHz), 49.7 kHz, 74.6 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "800x600": 50.0 MHz (scaled from 0.0 MHz), 48.1 kHz, 72.2 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "800x600": 49.5 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.3 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "800x600": 36.0 MHz (scaled from 0.0 MHz), 35.2 kHz, 56.2 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.5 kHz, 75.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.9 kHz, 72.8 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "640x480": 30.2 MHz (scaled from 0.0 MHz), 35.0 kHz, 66.7 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 3.224] (**) NOUVEAU(0): Driver mode "720x400": 28.3 MHz (scaled from 0.0 MHz), 31.5 kHz, 70.1 Hz
[ 3.224] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 3.224] (==) NOUVEAU(0): DPI set to (96, 96)
[ 3.224] (II) Loading sub module "fb"
[ 3.224] (II) LoadModule: "fb"
[ 3.225] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 3.226] (II) Module fb: vendor="X.Org Foundation"
[ 3.226] compiled for 1.14.4, module version = 1.0.0
[ 3.226] ABI class: X.Org ANSI C Emulation, version 0.4
[ 3.226] (II) Loading sub module "exa"
[ 3.226] (II) LoadModule: "exa"
[ 3.226] (II) Loading /usr/lib/xorg/modules/libexa.so
[ 3.227] (II) Module exa: vendor="X.Org Foundation"
[ 3.227] compiled for 1.14.4, module version = 2.6.0
[ 3.227] ABI class: X.Org Video Driver, version 14.1
[ 3.227] (II) Loading sub module "shadowfb"
[ 3.227] (II) LoadModule: "shadowfb"
[ 3.227] (II) Loading /usr/lib/xorg/modules/libshadowfb.so
[ 3.228] (II) Module shadowfb: vendor="X.Org Foundation"
[ 3.228] compiled for 1.14.4, module version = 1.0.0
[ 3.228] ABI class: X.Org ANSI C Emulation, version 0.4
[ 3.228] (--) Depth 24 pixmap format is 32 bpp
[ 3.228] (II) NOUVEAU(0): Opened GPU channel 0
[ 3.232] (II) NOUVEAU(0): [DRI2] Setup complete
[ 3.232] (II) NOUVEAU(0): [DRI2] DRI driver: nouveau
[ 3.232] (II) NOUVEAU(0): [DRI2] VDPAU driver: nouveau
[ 3.234] (II) EXA(0): Driver allocated offscreen pixmaps
[ 3.234] (II) EXA(0): Driver registered support for the following operations:
[ 3.234] (II) Solid
[ 3.234] (II) Copy
[ 3.234] (II) Composite (RENDER acceleration)
[ 3.234] (II) UploadToScreen
[ 3.234] (II) DownloadFromScreen
[ 3.234] (==) NOUVEAU(0): Backing store disabled
[ 3.234] (==) NOUVEAU(0): Silken mouse enabled
[ 3.234] (II) NOUVEAU(0): [XvMC] Associated with Nouveau GeForce 8/9 Textured Video.
[ 3.234] (II) NOUVEAU(0): [XvMC] Extension initialized.
[ 3.234] (==) NOUVEAU(0): DPMS enabled
[ 3.234] (II) NOUVEAU(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 3.235] (--) RandR disabled
[ 3.313] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 3.313] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 3.313] (II) AIGLX: enabled GLX_ARB_create_context
[ 3.313] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 3.313] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 3.313] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 3.313] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 3.313] (II) AIGLX: Loaded and initialized nouveau
[ 3.313] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 3.317] (II) NOUVEAU(0): NVEnterVT is called.
[ 3.395] (II) NOUVEAU(0): Setting screen physical size to 444 x 277
[ 3.395] resize called 1680 1050
[ 3.451] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 3.451] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 3.451] (II) LoadModule: "evdev"
[ 3.451] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 3.453] (II) Module evdev: vendor="X.Org Foundation"
[ 3.453] compiled for 1.14.3, module version = 2.8.2
[ 3.453] Module class: X.Org XInput Driver
[ 3.453] ABI class: X.Org XInput driver, version 19.1
[ 3.453] (II) Using input driver 'evdev' for 'Power Button'
[ 3.453] (**) Power Button: always reports core events
[ 3.453] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 3.453] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 3.453] (--) evdev: Power Button: Found keys
[ 3.453] (II) evdev: Power Button: Configuring as keyboard
[ 3.453] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event1"
[ 3.453] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 3.453] (**) Option "xkb_rules" "evdev"
[ 3.453] (**) Option "xkb_model" "pc104"
[ 3.453] (**) Option "xkb_layout" "us"
[ 3.478] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[ 3.478] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 3.478] (II) Using input driver 'evdev' for 'Power Button'
[ 3.478] (**) Power Button: always reports core events
[ 3.478] (**) evdev: Power Button: Device: "/dev/input/event0"
[ 3.478] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 3.478] (--) evdev: Power Button: Found keys
[ 3.478] (II) evdev: Power Button: Configuring as keyboard
[ 3.478] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event0"
[ 3.478] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 3.478] (**) Option "xkb_rules" "evdev"
[ 3.478] (**) Option "xkb_model" "pc104"
[ 3.478] (**) Option "xkb_layout" "us"
[ 3.478] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 3.479] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event3)
[ 3.479] (II) No input driver specified, ignoring this device.
[ 3.479] (II) This device may have been added with another device file.
[ 3.479] (II) config/udev: Adding input device HDA Intel Line Out CLFE (/dev/input/event6)
[ 3.479] (II) No input driver specified, ignoring this device.
[ 3.479] (II) This device may have been added with another device file.
[ 3.479] (II) config/udev: Adding input device HDA Intel Line Out Side (/dev/input/event5)
[ 3.479] (II) No input driver specified, ignoring this device.
[ 3.479] (II) This device may have been added with another device file.
[ 3.479] (II) config/udev: Adding input device HDA Intel Front Headphone (/dev/input/event4)
[ 3.479] (II) No input driver specified, ignoring this device.
[ 3.479] (II) This device may have been added with another device file.
[ 3.479] (II) config/udev: Adding input device HDA Intel Front Mic (/dev/input/event11)
[ 3.479] (II) No input driver specified, ignoring this device.
[ 3.479] (II) This device may have been added with another device file.
[ 3.479] (II) config/udev: Adding input device HDA Intel Rear Mic (/dev/input/event10)
[ 3.480] (II) No input driver specified, ignoring this device.
[ 3.480] (II) This device may have been added with another device file.
[ 3.480] (II) config/udev: Adding input device HDA Intel Line (/dev/input/event9)
[ 3.480] (II) No input driver specified, ignoring this device.
[ 3.480] (II) This device may have been added with another device file.
[ 3.480] (II) config/udev: Adding input device HDA Intel Line Out Front (/dev/input/event8)
[ 3.480] (II) No input driver specified, ignoring this device.
[ 3.480] (II) This device may have been added with another device file.
[ 3.480] (II) config/udev: Adding input device HDA Intel Line Out Surround (/dev/input/event7)
[ 3.480] (II) No input driver specified, ignoring this device.
[ 3.480] (II) This device may have been added with another device file.
[ 3.480] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:101a (/dev/input/event14)
[ 3.480] (**) Logitech Unifying Device. Wireless PID:101a: Applying InputClass "evdev pointer catchall"
[ 3.480] (II) Using input driver 'evdev' for 'Logitech Unifying Device. Wireless PID:101a'
[ 3.480] (**) Logitech Unifying Device. Wireless PID:101a: always reports core events
[ 3.480] (**) evdev: Logitech Unifying Device. Wireless PID:101a: Device: "/dev/input/event14"
[ 3.480] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Vendor 0x46d Product 0xc52b
[ 3.480] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found 20 mouse buttons
[ 3.480] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found scroll wheel(s)
[ 3.480] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found relative axes
[ 3.480] (--) evdev: Logitech Unifying Device. Wireless PID:101a: Found x and y relative axes
[ 3.480] (II) evdev: Logitech Unifying Device. Wireless PID:101a: Configuring as mouse
[ 3.480] (II) evdev: Logitech Unifying Device. Wireless PID:101a: Adding scrollwheel support
[ 3.480] (**) evdev: Logitech Unifying Device. Wireless PID:101a: YAxisMapping: buttons 4 and 5
[ 3.480] (**) evdev: Logitech Unifying Device. Wireless PID:101a: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 3.480] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.2/usb8/8-1/8-1:1.2/0003:046D:C52B.0003/input/input15/event14"
[ 3.481] (II) XINPUT: Adding extended input device "Logitech Unifying Device. Wireless PID:101a" (type: MOUSE, id 8)
[ 3.481] (II) evdev: Logitech Unifying Device. Wireless PID:101a: initialized for relative axes.
[ 3.481] (**) Logitech Unifying Device. Wireless PID:101a: (accel) keeping acceleration scheme 1
[ 3.481] (**) Logitech Unifying Device. Wireless PID:101a: (accel) acceleration profile 0
[ 3.481] (**) Logitech Unifying Device. Wireless PID:101a: (accel) acceleration factor: 2.000
[ 3.481] (**) Logitech Unifying Device. Wireless PID:101a: (accel) acceleration threshold: 4
[ 3.481] (II) config/udev: Adding input device Logitech Unifying Device. Wireless PID:101a (/dev/input/mouse0)
[ 3.481] (II) No input driver specified, ignoring this device.
[ 3.481] (II) This device may have been added with another device file.
[ 3.481] (II) config/udev: Adding input device Microsoft Comfort Curve Keyboard 2000 (/dev/input/event12)
[ 3.481] (**) Microsoft Comfort Curve Keyboard 2000: Applying InputClass "evdev keyboard catchall"
[ 3.481] (II) Using input driver 'evdev' for 'Microsoft Comfort Curve Keyboard 2000'
[ 3.481] (**) Microsoft Comfort Curve Keyboard 2000: always reports core events
[ 3.481] (**) evdev: Microsoft Comfort Curve Keyboard 2000: Device: "/dev/input/event12"
[ 3.481] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Vendor 0x45e Product 0xdd
[ 3.481] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found keys
[ 3.481] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Configuring as keyboard
[ 3.481] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.2/usb8/8-2/8-2:1.0/input/input13/event12"
[ 3.481] (II) XINPUT: Adding extended input device "Microsoft Comfort Curve Keyboard 2000" (type: KEYBOARD, id 9)
[ 3.481] (**) Option "xkb_rules" "evdev"
[ 3.481] (**) Option "xkb_model" "pc104"
[ 3.481] (**) Option "xkb_layout" "us"
[ 3.482] (II) config/udev: Adding input device Microsoft Comfort Curve Keyboard 2000 (/dev/input/event13)
[ 3.482] (**) Microsoft Comfort Curve Keyboard 2000: Applying InputClass "evdev keyboard catchall"
[ 3.482] (II) Using input driver 'evdev' for 'Microsoft Comfort Curve Keyboard 2000'
[ 3.482] (**) Microsoft Comfort Curve Keyboard 2000: always reports core events
[ 3.482] (**) evdev: Microsoft Comfort Curve Keyboard 2000: Device: "/dev/input/event13"
[ 3.482] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Vendor 0x45e Product 0xdd
[ 3.482] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found 1 mouse buttons
[ 3.482] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found scroll wheel(s)
[ 3.482] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found relative axes
[ 3.482] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Forcing relative x/y axes to exist.
[ 3.482] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found absolute axes
[ 3.482] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Forcing absolute x/y axes to exist.
[ 3.482] (--) evdev: Microsoft Comfort Curve Keyboard 2000: Found keys
[ 3.482] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Configuring as mouse
[ 3.482] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Configuring as keyboard
[ 3.482] (II) evdev: Microsoft Comfort Curve Keyboard 2000: Adding scrollwheel support
[ 3.482] (**) evdev: Microsoft Comfort Curve Keyboard 2000: YAxisMapping: buttons 4 and 5
[ 3.482] (**) evdev: Microsoft Comfort Curve Keyboard 2000: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 3.482] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.2/usb8/8-2/8-2:1.1/input/input14/event13"
[ 3.482] (II) XINPUT: Adding extended input device "Microsoft Comfort Curve Keyboard 2000" (type: KEYBOARD, id 10)
[ 3.482] (**) Option "xkb_rules" "evdev"
[ 3.482] (**) Option "xkb_model" "pc104"
[ 3.482] (**) Option "xkb_layout" "us"
[ 3.482] (II) evdev: Microsoft Comfort Curve Keyboard 2000: initialized for relative axes.
[ 3.482] (WW) evdev: Microsoft Comfort Curve Keyboard 2000: ignoring absolute axes.
[ 3.482] (**) Microsoft Comfort Curve Keyboard 2000: (accel) keeping acceleration scheme 1
[ 3.482] (**) Microsoft Comfort Curve Keyboard 2000: (accel) acceleration profile 0
[ 3.482] (**) Microsoft Comfort Curve Keyboard 2000: (accel) acceleration factor: 2.000
[ 3.482] (**) Microsoft Comfort Curve Keyboard 2000: (accel) acceleration threshold: 4
[ 3.482] (II) config/udev: Adding input device UVC Camera (046d:081b) (/dev/input/event15)
[ 3.482] (**) UVC Camera (046d:081b): Applying InputClass "evdev keyboard catchall"
[ 3.483] (II) Using input driver 'evdev' for 'UVC Camera (046d:081b)'
[ 3.483] (**) UVC Camera (046d:081b): always reports core events
[ 3.483] (**) evdev: UVC Camera (046d:081b): Device: "/dev/input/event15"
[ 3.483] (--) evdev: UVC Camera (046d:081b): Vendor 0x46d Product 0x81b
[ 3.483] (--) evdev: UVC Camera (046d:081b): Found keys
[ 3.483] (II) evdev: UVC Camera (046d:081b): Configuring as keyboard
[ 3.483] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.7/usb10/10-3/10-3:1.0/input/input16/event15"
[ 3.483] (II) XINPUT: Adding extended input device "UVC Camera (046d:081b)" (type: KEYBOARD, id 11)
[ 3.483] (**) Option "xkb_rules" "evdev"
[ 3.483] (**) Option "xkb_model" "pc104"
[ 3.483] (**) Option "xkb_layout" "us"
[ 3.483] (II) config/udev: Adding input device PC Speaker (/dev/input/event2)
[ 3.483] (II) No input driver specified, ignoring this device.
[ 3.483] (II) This device may have been added with another device file.
[ 3.486] (II) config/udev: removing device UVC Camera (046d:081b)
[ 3.523] (II) evdev: UVC Camera (046d:081b): Close
[ 3.523] (II) UnloadModule: "evdev"
[ 3.523] (II) config/udev: Adding input device UVC Camera (046d:081b) (/dev/input/event15)
[ 3.523] (**) UVC Camera (046d:081b): Applying InputClass "evdev keyboard catchall"
[ 3.523] (II) Using input driver 'evdev' for 'UVC Camera (046d:081b)'
[ 3.523] (**) UVC Camera (046d:081b): always reports core events
[ 3.523] (**) evdev: UVC Camera (046d:081b): Device: "/dev/input/event15"
[ 3.523] (--) evdev: UVC Camera (046d:081b): Vendor 0x46d Product 0x81b
[ 3.523] (--) evdev: UVC Camera (046d:081b): Found keys
[ 3.523] (II) evdev: UVC Camera (046d:081b): Configuring as keyboard
[ 3.523] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.7/usb10/10-3/10-3:1.0/input/input16/event15"
[ 3.523] (II) XINPUT: Adding extended input device "UVC Camera (046d:081b)" (type: KEYBOARD, id 11)
[ 3.523] (**) Option "xkb_rules" "evdev"
[ 3.523] (**) Option "xkb_model" "pc104"
[ 3.523] (**) Option "xkb_layout" "us"
[ 4.601] (II) NOUVEAU(0): EDID vendor "ACR", prod id 44449
[ 4.601] (II) NOUVEAU(0): Using EDID range info for horizontal sync
[ 4.601] (II) NOUVEAU(0): Using EDID range info for vertical refresh
[ 4.601] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 4.601] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync -vsync (65.3 kHz eP)
[ 4.601] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1366x768"x59.8 84.75 1366 1431 1567 1776 768 771 781 798 -hsync +vsync (47.7 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1440x900"x0.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1440x900"x0.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 4.601] (II) NOUVEAU(0): Modeline "1400x1050"x0.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 4.846] resize called 3600 1080
[ 5.760] (II) NOUVEAU(0): EDID vendor "ACR", prod id 44449
[ 5.760] (II) NOUVEAU(0): Using hsync ranges from config file
[ 5.760] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 5.760] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 5.760] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync -vsync (65.3 kHz eP)
[ 5.760] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 5.760] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 5.760] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 5.760] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1366x768"x59.8 84.75 1366 1431 1567 1776 768 771 781 798 -hsync +vsync (47.7 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1440x900"x0.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1440x900"x0.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 5.761] (II) NOUVEAU(0): Modeline "1400x1050"x0.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 13.425] (II) NOUVEAU(0): EDID vendor "ACR", prod id 44449
[ 13.425] (II) NOUVEAU(0): Using hsync ranges from config file
[ 13.425] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 13.425] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 13.425] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync -vsync (65.3 kHz eP)
[ 13.425] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 13.425] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 13.425] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 13.425] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 13.425] (II) NOUVEAU(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1366x768"x59.8 84.75 1366 1431 1567 1776 768 771 781 798 -hsync +vsync (47.7 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1440x900"x0.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1440x900"x0.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 13.426] (II) NOUVEAU(0): Modeline "1400x1050"x0.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 13.670] resize called 3360 1050
[ 14.298] (II) NOUVEAU(0): EDID vendor "ACR", prod id 44449
[ 14.298] (II) NOUVEAU(0): Using hsync ranges from config file
[ 14.298] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 14.298] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 14.298] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync -vsync (65.3 kHz eP)
[ 14.298] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1366x768"x59.8 84.75 1366 1431 1567 1776 768 771 781 798 -hsync +vsync (47.7 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1440x900"x0.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1440x900"x0.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 14.299] (II) NOUVEAU(0): Modeline "1400x1050"x0.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 190.714] (II) NOUVEAU(0): EDID vendor "ACR", prod id 44449
[ 190.714] (II) NOUVEAU(0): Using hsync ranges from config file
[ 190.714] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 190.714] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 190.714] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync -vsync (65.3 kHz eP)
[ 190.714] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1366x768"x59.8 84.75 1366 1431 1567 1776 768 771 781 798 -hsync +vsync (47.7 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1440x900"x0.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1440x900"x0.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 190.714] (II) NOUVEAU(0): Modeline "1400x1050"x0.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 202.800] (II) NOUVEAU(0): EDID vendor "ACR", prod id 44449
[ 202.800] (II) NOUVEAU(0): Using hsync ranges from config file
[ 202.800] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 202.800] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 202.800] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync -vsync (65.3 kHz eP)
[ 202.800] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1366x768"x59.8 84.75 1366 1431 1567 1776 768 771 781 798 -hsync +vsync (47.7 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1440x900"x0.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1440x900"x0.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 202.800] (II) NOUVEAU(0): Modeline "1400x1050"x0.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 202.890] (II) NOUVEAU(0): EDID vendor "ACR", prod id 44449
[ 202.890] (II) NOUVEAU(0): Using hsync ranges from config file
[ 202.890] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 202.890] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 202.890] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync -vsync (65.3 kHz eP)
[ 202.890] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 202.890] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 202.890] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 202.890] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e)
[ 202.890] (II) NOUVEAU(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 202.890] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 202.890] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 202.890] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 202.890] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e)
[ 202.890] (II) NOUVEAU(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "1366x768"x59.8 84.75 1366 1431 1567 1776 768 771 781 798 -hsync +vsync (47.7 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "1440x900"x0.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "1440x900"x0.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 202.891] (II) NOUVEAU(0): Modeline "1400x1050"x0.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
cat /etc/mkinitcpio.conf
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES=""
# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image. This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way. This is useful for config files.
FILES=""
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
## This setup specifies all modules in the MODULES setting above.
##

Problem with nvidia driver, causing system to be unusable

Hello, I've got a problem I assume with nvidia driver. My graphics card is gtx 460, here's my usual glxgears output:
http://dl.dropbox.com/u/16474487/noerror.png
After random amount of time (usually from 30 mins to ~2hours) something 'breaks' and here's what happens:
http://dl.dropbox.com/u/16474487/error.png
I've tried different desktop environments, under xfce4 it also breaks, i've been testing also nvidia-beta and nvidia-all drivers, but it won't help. After 'breaking' i must restart nvidia module, then all again is working fine.
-- mod edit: read the Forum Etiquette and only post thumbnails http://wiki.archlinux.org/index.php/For … s_and_Code [jwr] --

Vazz wrote:Hello, I've got a problem I assume with nvidia driver. My graphics card is gtx 460, here's my usual glxgears output:
http://dl.dropbox.com/u/16474487/noerror.png
After random amount of time (usually from 30 mins to ~2hours) something 'breaks' and here's what happens:
http://dl.dropbox.com/u/16474487/error.png
I've tried different desktop environments, under xfce4 it also breaks, i've been testing also nvidia-beta and nvidia-all drivers, but it won't help. After 'breaking' i must restart nvidia module, then all again is working fine.
Hey Vazz, there is a problem with the nvidia linux drivers/gtx460 hardware, but sadly it only affects a small population.
There is a thread on the nvidia support forums with many others having more or less the same problems.
Still no response from nvidia yet... In the meantime use nouveau.
Last edited by Loafers (2011-01-20 05:13:58)

[SOLVED] XOrg fails to load Nvidia driver on startup

Hi,
I'm having a fairly strange issue where XOrg is failing to load my driver when I start up my laptop. I'm using kdm, but this is causing it to fail. However, doing a simple
$sudo systemctl restart kdm
works, and everything starts up fine. When kdm is in the failed state, I see this:
$sudo systemctl status kdm
● kdm.service - K Display Manager
Loaded: loaded (/usr/lib/systemd/system/kdm.service; enabled; vendor preset: disabled)
Active: active (running) since Fri 2014-12-19 18:47:26 EST; 41s ago
Main PID: 247 (kdm)
CGroup: /system.slice/kdm.service
└─247 /usr/bin/kdm -nodaemon
Dec 19 18:47:26 laptop systemd[1]: Started K Display Manager.
Dec 19 18:47:27 laptop kdm[247]: X server died during startup
Dec 19 18:47:27 laptop kdm[247]: X server for display :0 cannot be started, session disabled
And in my XOrg log, I see:
[ 3.639]
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
[ 3.639]
X.Org X Server 1.16.2.901 (1.16.3 RC 1)
Release Date: 2014-12-09
[ 3.639] X Protocol Version 11, Revision 0
[ 3.639] Build Operating System: Linux 3.17.2-1-ARCH x86_64
[ 3.639] Current Operating System: Linux laptop 3.17.6-1-ARCH #1 SMP PREEMPT Sun Dec 7 23:43:32 UTC 2014 x86_64
[ 3.639] Kernel command line: BOOT_IMAGE=../vmlinuz-linux root=/dev/sda1 rw initrd=../initramfs-linux.img
[ 3.639] Build Date: 10 December 2014 02:34:24PM
[ 3.639]
[ 3.639] Current version of pixman: 0.32.6
[ 3.639] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 3.639] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 3.639] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Dec 19 18:47:26 2014
[ 3.645] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 3.649] (==) No Layout section. Using the first Screen section.
[ 3.649] (==) No screen section available. Using defaults.
[ 3.649] (**) |-->Screen "Default Screen Section" (0)
[ 3.649] (**) | |-->Monitor "<default monitor>"
[ 3.650] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 3.650] (==) Automatically adding devices
[ 3.650] (==) Automatically enabling devices
[ 3.650] (==) Automatically adding GPU devices
[ 3.658] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 3.658] Entry deleted from font path.
[ 3.659] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 3.659] Entry deleted from font path.
[ 3.659] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 3.660] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 3.660] Entry deleted from font path.
[ 3.660] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 3.660] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 3.660] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 3.660] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 3.660] (II) Loader magic: 0x818d80
[ 3.660] (II) Module ABI versions:
[ 3.660] X.Org ANSI C Emulation: 0.4
[ 3.660] X.Org Video Driver: 18.0
[ 3.660] X.Org XInput driver : 21.0
[ 3.660] X.Org Server Extension : 8.0
[ 3.662] (EE) systemd-logind: failed to get session: PID 267 does not belong to any known session
[ 3.663] (--) PCI:*(0:1:0:0) 10de:11a1:1558:0371 rev 161, Mem @ 0xf6000000/16777216, 0xe0000000/268435456, 0xf0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288
[ 3.663] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 3.664] (II) LoadModule: "glx"
[ 3.675] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 3.767] (II) Module glx: vendor="NVIDIA Corporation"
[ 3.767] compiled for 4.0.2, module version = 1.0.0
[ 3.767] Module class: X.Org Server Extension
[ 3.768] (II) NVIDIA GLX Module 343.36 Mon Dec 1 15:50:02 PST 2014
[ 3.769] (==) Matched nouveau as autoconfigured driver 0
[ 3.769] (==) Matched nv as autoconfigured driver 1
[ 3.769] (==) Matched modesetting as autoconfigured driver 2
[ 3.769] (==) Matched fbdev as autoconfigured driver 3
[ 3.769] (==) Matched vesa as autoconfigured driver 4
[ 3.769] (==) Assigned the driver to the xf86ConfigLayout
[ 3.769] (II) LoadModule: "nouveau"
[ 3.769] (WW) Warning, couldn't open module nouveau
[ 3.769] (II) UnloadModule: "nouveau"
[ 3.769] (II) Unloading nouveau
[ 3.769] (EE) Failed to load module "nouveau" (module does not exist, 0)
[ 3.769] (II) LoadModule: "nv"
[ 3.769] (WW) Warning, couldn't open module nv
[ 3.769] (II) UnloadModule: "nv"
[ 3.769] (II) Unloading nv
[ 3.769] (EE) Failed to load module "nv" (module does not exist, 0)
[ 3.769] (II) LoadModule: "modesetting"
[ 3.769] (WW) Warning, couldn't open module modesetting
[ 3.769] (II) UnloadModule: "modesetting"
[ 3.769] (II) Unloading modesetting
[ 3.769] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 3.769] (II) LoadModule: "fbdev"
[ 3.769] (WW) Warning, couldn't open module fbdev
[ 3.769] (II) UnloadModule: "fbdev"
[ 3.769] (II) Unloading fbdev
[ 3.769] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 3.769] (II) LoadModule: "vesa"
[ 3.770] (WW) Warning, couldn't open module vesa
[ 3.770] (II) UnloadModule: "vesa"
[ 3.770] (II) Unloading vesa
[ 3.770] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 3.770] (EE) No drivers available.
[ 3.770] (EE)
Fatal server error:
[ 3.770] (EE) no screens found(EE)
[ 3.770] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 3.770] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 3.770] (EE)
Which looks like it loads my nvidia driver, but then just decides not to use it for some reason... After I restart kdm, it seems to use the driver fine:
[ 78.897]
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
[ 78.897]
X.Org X Server 1.16.2.901 (1.16.3 RC 1)
Release Date: 2014-12-09
[ 78.897] X Protocol Version 11, Revision 0
[ 78.897] Build Operating System: Linux 3.17.2-1-ARCH x86_64
[ 78.897] Current Operating System: Linux laptop 3.17.6-1-ARCH #1 SMP PREEMPT Sun Dec 7 23:43:32 UTC 2014 x86_64
[ 78.897] Kernel command line: BOOT_IMAGE=../vmlinuz-linux root=/dev/sda1 rw initrd=../initramfs-linux.img
[ 78.897] Build Date: 10 December 2014 02:34:24PM
[ 78.897]
[ 78.897] Current version of pixman: 0.32.6
[ 78.897] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 78.897] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 78.897] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Dec 19 18:48:38 2014
[ 78.897] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 78.897] (==) No Layout section. Using the first Screen section.
[ 78.897] (==) No screen section available. Using defaults.
[ 78.897] (**) |-->Screen "Default Screen Section" (0)
[ 78.897] (**) | |-->Monitor "<default monitor>"
[ 78.898] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 78.898] (==) Automatically adding devices
[ 78.898] (==) Automatically enabling devices
[ 78.898] (==) Automatically adding GPU devices
[ 78.898] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 78.898] Entry deleted from font path.
[ 78.898] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 78.898] Entry deleted from font path.
[ 78.898] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 78.898] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 78.898] Entry deleted from font path.
[ 78.898] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 78.898] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 78.898] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 78.898] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 78.898] (II) Loader magic: 0x818d80
[ 78.898] (II) Module ABI versions:
[ 78.898] X.Org ANSI C Emulation: 0.4
[ 78.898] X.Org Video Driver: 18.0
[ 78.898] X.Org XInput driver : 21.0
[ 78.898] X.Org Server Extension : 8.0
[ 78.900] (EE) systemd-logind: failed to get session: PID 542 does not belong to any known session
[ 78.900] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 78.901] (--) PCI:*(0:1:0:0) 10de:11a1:1558:0371 rev 161, Mem @ 0xf6000000/16777216, 0xe0000000/268435456, 0xf0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288
[ 78.901] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 78.901] (II) LoadModule: "glx"
[ 78.902] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 78.913] (II) Module glx: vendor="NVIDIA Corporation"
[ 78.913] compiled for 4.0.2, module version = 1.0.0
[ 78.913] Module class: X.Org Server Extension
[ 78.913] (II) NVIDIA GLX Module 343.36 Mon Dec 1 15:50:02 PST 2014
[ 78.914] (II) Applying OutputClass "nvidia" to /dev/dri/card0
[ 78.914] loading driver: nvidia
[ 78.914] (==) Matched nvidia as autoconfigured driver 0
[ 78.914] (==) Matched nouveau as autoconfigured driver 1
[ 78.914] (==) Matched nv as autoconfigured driver 2
[ 78.914] (==) Matched nouveau as autoconfigured driver 3
[ 78.914] (==) Matched nv as autoconfigured driver 4
[ 78.914] (==) Matched modesetting as autoconfigured driver 5
[ 78.914] (==) Matched fbdev as autoconfigured driver 6
[ 78.914] (==) Matched vesa as autoconfigured driver 7
[ 78.914] (==) Assigned the driver to the xf86ConfigLayout
[ 78.914] (II) LoadModule: "nvidia"
[ 78.914] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 78.920] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 78.920] compiled for 4.0.2, module version = 1.0.0
[ 78.920] Module class: X.Org Video Driver
[ 78.920] (II) LoadModule: "nouveau"
[ 78.921] (WW) Warning, couldn't open module nouveau
[ 78.921] (II) UnloadModule: "nouveau"
[ 78.921] (II) Unloading nouveau
[ 78.921] (EE) Failed to load module "nouveau" (module does not exist, 0)
[ 78.921] (II) LoadModule: "nv"
[ 78.921] (WW) Warning, couldn't open module nv
[ 78.921] (II) UnloadModule: "nv"
[ 78.921] (II) Unloading nv
[ 78.921] (EE) Failed to load module "nv" (module does not exist, 0)
[ 78.921] (II) LoadModule: "modesetting"
[ 78.921] (WW) Warning, couldn't open module modesetting
[ 78.921] (II) UnloadModule: "modesetting"
[ 78.921] (II) Unloading modesetting
[ 78.921] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 78.921] (II) LoadModule: "fbdev"
[ 78.922] (WW) Warning, couldn't open module fbdev
[ 78.922] (II) UnloadModule: "fbdev"
[ 78.922] (II) Unloading fbdev
[ 78.922] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 78.922] (II) LoadModule: "vesa"
[ 78.922] (WW) Warning, couldn't open module vesa
[ 78.922] (II) UnloadModule: "vesa"
[ 78.922] (II) Unloading vesa
[ 78.922] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 78.922] (II) NVIDIA dlloader X Driver 343.36 Mon Dec 1 15:28:39 PST 2014
[ 78.922] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 78.922] (++) using VT number 7
[ 78.935] (II) Loading sub module "fb"
[ 78.935] (II) LoadModule: "fb"
[ 78.935] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 78.936] (II) Module fb: vendor="X.Org Foundation"
[ 78.936] compiled for 1.16.2.901, module version = 1.0.0
[ 78.936] ABI class: X.Org ANSI C Emulation, version 0.4
[ 78.936] (II) Loading sub module "wfb"
[ 78.936] (II) LoadModule: "wfb"
[ 78.936] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 78.937] (II) Module wfb: vendor="X.Org Foundation"
[ 78.937] compiled for 1.16.2.901, module version = 1.0.0
[ 78.937] ABI class: X.Org ANSI C Emulation, version 0.4
[ 78.937] (II) Loading sub module "ramdac"
[ 78.937] (II) LoadModule: "ramdac"
[ 78.937] (II) Module "ramdac" already built-in
[ 78.939] (II) NVIDIA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 78.939] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[ 78.939] (==) NVIDIA(0): RGB weight 888
[ 78.939] (==) NVIDIA(0): Default visual is TrueColor
[ 78.939] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 78.940] (**) NVIDIA(0): Enabling 2D acceleration
[ 79.610] (II) NVIDIA(0): Display (Samsung SyncMaster (DFP-1)) does not support NVIDIA
[ 79.610] (II) NVIDIA(0): 3D Vision stereo.
[ 79.610] (II) NVIDIA(GPU-0): Found DRM driver nvidia-drm (20130102)
[ 79.612] (II) NVIDIA(0): NVIDIA GPU GeForce GTX 670MX (GK104) at PCI:1:0:0 (GPU-0)
[ 79.612] (--) NVIDIA(0): Memory: 3145728 kBytes
[ 79.612] (--) NVIDIA(0): VideoBIOS: 80.04.67.00.06
[ 79.612] (II) NVIDIA(0): Detected PCI Express Link width: 16X
[ 79.616] (--) NVIDIA(0): Valid display device(s) on GeForce GTX 670MX at PCI:1:0:0
[ 79.616] (--) NVIDIA(0): Chi Mei Optoelectronics corp. (DFP-0) (boot, connected)
[ 79.616] (--) NVIDIA(0): Samsung SyncMaster (DFP-1) (connected)
[ 79.616] (--) NVIDIA(0): DFP-2
[ 79.616] (--) NVIDIA(0): DFP-3
[ 79.616] (--) NVIDIA(0): DFP-4
[ 79.616] (--) NVIDIA(0): Chi Mei Optoelectronics corp. (DFP-0): Internal LVDS
[ 79.616] (--) NVIDIA(GPU-0): Chi Mei Optoelectronics corp. (DFP-0): 330.0 MHz maximum pixel clock
[ 79.616] (--) NVIDIA(0): Samsung SyncMaster (DFP-1): Internal TMDS
[ 79.616] (--) NVIDIA(GPU-0): Samsung SyncMaster (DFP-1): 165.0 MHz maximum pixel clock
[ 79.616] (--) NVIDIA(0): DFP-2: Internal TMDS
[ 79.616] (--) NVIDIA(GPU-0): DFP-2: 165.0 MHz maximum pixel clock
[ 79.616] (--) NVIDIA(0): DFP-3: Internal DisplayPort
[ 79.616] (--) NVIDIA(GPU-0): DFP-3: 960.0 MHz maximum pixel clock
[ 79.616] (--) NVIDIA(0): DFP-4: Internal DisplayPort
[ 79.616] (--) NVIDIA(GPU-0): DFP-4: 960.0 MHz maximum pixel clock
[ 79.616] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
[ 79.616] (**) NVIDIA(0): device Chi Mei Optoelectronics corp. (DFP-0) (Using EDID
[ 79.616] (**) NVIDIA(0): frequencies has been enabled on all display devices.)
[ 79.616] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
[ 79.616] (**) NVIDIA(0): device Samsung SyncMaster (DFP-1) (Using EDID frequencies
[ 79.616] (**) NVIDIA(0): has been enabled on all display devices.)
[ 79.618] (==) NVIDIA(0):
[ 79.618] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
[ 79.618] (==) NVIDIA(0): will be used as the requested mode.
[ 79.618] (==) NVIDIA(0):
[ 79.619] (II) NVIDIA(0): Validated MetaModes:
[ 79.619] (II) NVIDIA(0): "DFP-0:nvidia-auto-select,DFP-1:nvidia-auto-select"
[ 79.619] (II) NVIDIA(0): Virtual screen size determined to be 3600 x 1080
[ 80.144] (--) NVIDIA(0): DPI set to (128, 130); computed from "UseEdidDpi" X config
[ 80.144] (--) NVIDIA(0): option
[ 80.144] (--) Depth 24 pixmap format is 32 bpp
[ 80.144] (II) NVIDIA: Using 3072.00 MB of virtual memory for indirect memory
[ 80.144] (II) NVIDIA: access.
[ 80.150] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[ 80.150] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
[ 80.150] (II) NVIDIA(0): configuration option may not be set correctly. When the
[ 80.150] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
[ 80.150] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
[ 80.150] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
[ 80.150] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
[ 80.150] (II) NVIDIA(0): Config Options in the README.
[ 80.155] (II) NVIDIA(0): Setting mode "DFP-0:nvidia-auto-select,DFP-1:nvidia-auto-select"
[ 80.532] (==) NVIDIA(0): Disabling shared memory pixmaps
[ 80.532] (==) NVIDIA(0): Backing store enabled
[ 80.532] (==) NVIDIA(0): Silken mouse enabled
[ 80.533] (==) NVIDIA(0): DPMS enabled
[ 80.533] (II) Loading sub module "dri2"
[ 80.533] (II) LoadModule: "dri2"
[ 80.533] (II) Module "dri2" already built-in
[ 80.533] (II) NVIDIA(0): [DRI2] Setup complete
[ 80.533] (II) NVIDIA(0): [DRI2] VDPAU driver: nvidia
[ 80.533] (--) RandR disabled
[ 80.539] (II) Initializing extension GLX
[ 80.605] (II) config/udev: Adding input device Power Button (/dev/input/event14)
[ 80.605] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 80.605] (II) LoadModule: "evdev"
[ 80.606] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 80.607] (II) Module evdev: vendor="X.Org Foundation"
[ 80.607] compiled for 1.16.2, module version = 2.9.1
[ 80.607] Module class: X.Org XInput Driver
[ 80.607] ABI class: X.Org XInput driver, version 21.0
[ 80.607] (II) Using input driver 'evdev' for 'Power Button'
[ 80.607] (**) Power Button: always reports core events
[ 80.607] (**) evdev: Power Button: Device: "/dev/input/event14"
[ 80.608] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 80.608] (--) evdev: Power Button: Found keys
[ 80.608] (II) evdev: Power Button: Configuring as keyboard
[ 80.608] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input18/event14"
[ 80.608] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 80.608] (**) Option "xkb_rules" "evdev"
[ 80.608] (**) Option "xkb_model" "pc104"
[ 80.608] (**) Option "xkb_layout" "us"
[ 80.635] (II) config/udev: Adding input device Video Bus (/dev/input/event15)
[ 80.635] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 80.635] (II) Using input driver 'evdev' for 'Video Bus'
[ 80.635] (**) Video Bus: always reports core events
[ 80.635] (**) evdev: Video Bus: Device: "/dev/input/event15"
[ 80.635] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 80.635] (--) evdev: Video Bus: Found keys
[ 80.635] (II) evdev: Video Bus: Configuring as keyboard
[ 80.635] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:13/LNXVIDEO:00/input/input19/event15"
[ 80.635] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 80.635] (**) Option "xkb_rules" "evdev"
[ 80.635] (**) Option "xkb_model" "pc104"
[ 80.635] (**) Option "xkb_layout" "us"
[ 80.636] (II) config/udev: Adding input device Power Button (/dev/input/event13)
[ 80.636] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 80.636] (II) Using input driver 'evdev' for 'Power Button'
[ 80.636] (**) Power Button: always reports core events
[ 80.636] (**) evdev: Power Button: Device: "/dev/input/event13"
[ 80.636] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 80.636] (--) evdev: Power Button: Found keys
[ 80.636] (II) evdev: Power Button: Configuring as keyboard
[ 80.636] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input17/event13"
[ 80.636] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 80.636] (**) Option "xkb_rules" "evdev"
[ 80.636] (**) Option "xkb_model" "pc104"
[ 80.636] (**) Option "xkb_layout" "us"
[ 80.637] (II) config/udev: Adding input device Lid Switch (/dev/input/event11)
[ 80.637] (II) No input driver specified, ignoring this device.
[ 80.637] (II) This device may have been added with another device file.
[ 80.637] (II) config/udev: Adding input device Sleep Button (/dev/input/event12)
[ 80.637] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 80.637] (II) Using input driver 'evdev' for 'Sleep Button'
[ 80.637] (**) Sleep Button: always reports core events
[ 80.637] (**) evdev: Sleep Button: Device: "/dev/input/event12"
[ 80.637] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[ 80.637] (--) evdev: Sleep Button: Found keys
[ 80.637] (II) evdev: Sleep Button: Configuring as keyboard
[ 80.637] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input16/event12"
[ 80.637] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[ 80.637] (**) Option "xkb_rules" "evdev"
[ 80.637] (**) Option "xkb_model" "pc104"
[ 80.637] (**) Option "xkb_layout" "us"
[ 80.638] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event18)
[ 80.638] (II) No input driver specified, ignoring this device.
[ 80.638] (II) This device may have been added with another device file.
[ 80.638] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event19)
[ 80.638] (II) No input driver specified, ignoring this device.
[ 80.638] (II) This device may have been added with another device file.
[ 80.639] (II) config/udev: Adding input device LOGITECH G110 G-keys (/dev/input/event3)
[ 80.639] (**) LOGITECH G110 G-keys: Applying InputClass "evdev keyboard catchall"
[ 80.639] (II) Using input driver 'evdev' for 'LOGITECH G110 G-keys'
[ 80.639] (**) LOGITECH G110 G-keys: always reports core events
[ 80.639] (**) evdev: LOGITECH G110 G-keys: Device: "/dev/input/event3"
[ 80.639] (--) evdev: LOGITECH G110 G-keys: Vendor 0x46d Product 0xc22b
[ 80.639] (--) evdev: LOGITECH G110 G-keys: Found keys
[ 80.639] (II) evdev: LOGITECH G110 G-keys: Configuring as keyboard
[ 80.639] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4.1/3-4.1.1/3-4.1.1:1.0/0003:046D:C22B.0003/input/input7/event3"
[ 80.639] (II) XINPUT: Adding extended input device "LOGITECH G110 G-keys" (type: KEYBOARD, id 10)
[ 80.639] (**) Option "xkb_rules" "evdev"
[ 80.639] (**) Option "xkb_model" "pc104"
[ 80.639] (**) Option "xkb_layout" "us"
[ 80.639] (II) config/udev: Adding input device Gaming Keyboard G110 (/dev/input/event4)
[ 80.639] (**) Gaming Keyboard G110: Applying InputClass "evdev keyboard catchall"
[ 80.639] (II) Using input driver 'evdev' for 'Gaming Keyboard G110'
[ 80.639] (**) Gaming Keyboard G110: always reports core events
[ 80.639] (**) evdev: Gaming Keyboard G110: Device: "/dev/input/event4"
[ 80.640] (--) evdev: Gaming Keyboard G110: Vendor 0x46d Product 0xc22a
[ 80.640] (--) evdev: Gaming Keyboard G110: Found keys
[ 80.640] (II) evdev: Gaming Keyboard G110: Configuring as keyboard
[ 80.640] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4.1/3-4.1.3/3-4.1.3:1.0/0003:046D:C22A.0004/input/input8/event4"
[ 80.640] (II) XINPUT: Adding extended input device "Gaming Keyboard G110" (type: KEYBOARD, id 11)
[ 80.640] (**) Option "xkb_rules" "evdev"
[ 80.640] (**) Option "xkb_model" "pc104"
[ 80.640] (**) Option "xkb_layout" "us"
[ 80.640] (II) config/udev: Adding input device Gaming Keyboard G110 (/dev/input/event5)
[ 80.640] (**) Gaming Keyboard G110: Applying InputClass "evdev keyboard catchall"
[ 80.640] (II) Using input driver 'evdev' for 'Gaming Keyboard G110'
[ 80.640] (**) Gaming Keyboard G110: always reports core events
[ 80.640] (**) evdev: Gaming Keyboard G110: Device: "/dev/input/event5"
[ 80.640] (--) evdev: Gaming Keyboard G110: Vendor 0x46d Product 0xc22a
[ 80.640] (--) evdev: Gaming Keyboard G110: Found keys
[ 80.640] (II) evdev: Gaming Keyboard G110: Configuring as keyboard
[ 80.640] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4.1/3-4.1.3/3-4.1.3:1.1/0003:046D:C22A.0005/input/input9/event5"
[ 80.640] (II) XINPUT: Adding extended input device "Gaming Keyboard G110" (type: KEYBOARD, id 12)
[ 80.640] (**) Option "xkb_rules" "evdev"
[ 80.640] (**) Option "xkb_model" "pc104"
[ 80.641] (**) Option "xkb_layout" "us"
[ 80.641] (II) config/udev: Adding input device Razer Razer Lachesis (/dev/input/event1)
[ 80.641] (**) Razer Razer Lachesis: Applying InputClass "evdev pointer catchall"
[ 80.641] (II) Using input driver 'evdev' for 'Razer Razer Lachesis'
[ 80.641] (**) Razer Razer Lachesis: always reports core events
[ 80.641] (**) evdev: Razer Razer Lachesis: Device: "/dev/input/event1"
[ 80.641] (--) evdev: Razer Razer Lachesis: Vendor 0x1532 Product 0xc
[ 80.641] (--) evdev: Razer Razer Lachesis: Found 12 mouse buttons
[ 80.641] (--) evdev: Razer Razer Lachesis: Found scroll wheel(s)
[ 80.641] (--) evdev: Razer Razer Lachesis: Found relative axes
[ 80.641] (--) evdev: Razer Razer Lachesis: Found x and y relative axes
[ 80.641] (II) evdev: Razer Razer Lachesis: Configuring as mouse
[ 80.641] (II) evdev: Razer Razer Lachesis: Adding scrollwheel support
[ 80.641] (**) evdev: Razer Razer Lachesis: YAxisMapping: buttons 4 and 5
[ 80.641] (**) evdev: Razer Razer Lachesis: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 80.641] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4.2/3-4.2:1.0/0003:1532:000C.0001/input/input5/event1"
[ 80.641] (II) XINPUT: Adding extended input device "Razer Razer Lachesis" (type: MOUSE, id 13)
[ 80.642] (II) evdev: Razer Razer Lachesis: initialized for relative axes.
[ 80.642] (**) Razer Razer Lachesis: (accel) keeping acceleration scheme 1
[ 80.642] (**) Razer Razer Lachesis: (accel) acceleration profile 0
[ 80.642] (**) Razer Razer Lachesis: (accel) acceleration factor: 2.000
[ 80.642] (**) Razer Razer Lachesis: (accel) acceleration threshold: 4
[ 80.642] (II) config/udev: Adding input device Razer Razer Lachesis (/dev/input/mouse0)
[ 80.642] (II) No input driver specified, ignoring this device.
[ 80.642] (II) This device may have been added with another device file.
[ 80.643] (II) config/udev: Adding input device Razer Razer Lachesis (/dev/input/event2)
[ 80.643] (**) Razer Razer Lachesis: Applying InputClass "evdev keyboard catchall"
[ 80.643] (II) Using input driver 'evdev' for 'Razer Razer Lachesis'
[ 80.643] (**) Razer Razer Lachesis: always reports core events
[ 80.643] (**) evdev: Razer Razer Lachesis: Device: "/dev/input/event2"
[ 80.643] (--) evdev: Razer Razer Lachesis: Vendor 0x1532 Product 0xc
[ 80.643] (--) evdev: Razer Razer Lachesis: Found keys
[ 80.643] (II) evdev: Razer Razer Lachesis: Configuring as keyboard
[ 80.643] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4.2/3-4.2:1.1/0003:1532:000C.0002/input/input6/event2"
[ 80.643] (II) XINPUT: Adding extended input device "Razer Razer Lachesis" (type: KEYBOARD, id 14)
[ 80.643] (**) Option "xkb_rules" "evdev"
[ 80.643] (**) Option "xkb_model" "pc104"
[ 80.643] (**) Option "xkb_layout" "us"
[ 80.643] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event6)
[ 80.643] (II) No input driver specified, ignoring this device.
[ 80.643] (II) This device may have been added with another device file.
[ 80.644] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event7)
[ 80.644] (II) No input driver specified, ignoring this device.
[ 80.644] (II) This device may have been added with another device file.
[ 80.644] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event8)
[ 80.644] (II) No input driver specified, ignoring this device.
[ 80.644] (II) This device may have been added with another device file.
[ 80.644] (II) config/udev: Adding input device HDA Intel PCH Line Out (/dev/input/event9)
[ 80.644] (II) No input driver specified, ignoring this device.
[ 80.644] (II) This device may have been added with another device file.
[ 80.645] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event10)
[ 80.645] (II) No input driver specified, ignoring this device.
[ 80.645] (II) This device may have been added with another device file.
[ 80.645] (II) config/udev: Adding input device BisonCam, NB Pro (/dev/input/event17)
[ 80.645] (**) BisonCam, NB Pro: Applying InputClass "evdev keyboard catchall"
[ 80.645] (II) Using input driver 'evdev' for 'BisonCam, NB Pro'
[ 80.645] (**) BisonCam, NB Pro: always reports core events
[ 80.645] (**) evdev: BisonCam, NB Pro: Device: "/dev/input/event17"
[ 80.645] (--) evdev: BisonCam, NB Pro: Vendor 0x5986 Product 0x512
[ 80.645] (--) evdev: BisonCam, NB Pro: Found keys
[ 80.645] (II) evdev: BisonCam, NB Pro: Configuring as keyboard
[ 80.645] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.6/2-1.6:1.0/input/input23/event17"
[ 80.645] (II) XINPUT: Adding extended input device "BisonCam, NB Pro" (type: KEYBOARD, id 15)
[ 80.645] (**) Option "xkb_rules" "evdev"
[ 80.645] (**) Option "xkb_model" "pc104"
[ 80.645] (**) Option "xkb_layout" "us"
[ 80.646] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 80.646] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 80.646] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 80.646] (**) AT Translated Set 2 keyboard: always reports core events
[ 80.646] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 80.646] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 80.646] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 80.646] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 80.646] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 80.646] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 16)
[ 80.646] (**) Option "xkb_rules" "evdev"
[ 80.646] (**) Option "xkb_model" "pc104"
[ 80.646] (**) Option "xkb_layout" "us"
[ 80.646] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event20)
[ 80.646] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[ 80.647] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 80.647] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "Default clickpad buttons"
[ 80.647] (II) LoadModule: "synaptics"
[ 80.647] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 80.647] (II) Module synaptics: vendor="X.Org Foundation"
[ 80.647] compiled for 1.16.0, module version = 1.8.1
[ 80.647] Module class: X.Org XInput Driver
[ 80.647] ABI class: X.Org XInput driver, version 21.0
[ 80.647] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[ 80.647] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 80.647] (**) Option "Device" "/dev/input/event20"
[ 80.756] (II) synaptics: SynPS/2 Synaptics TouchPad: found clickpad property
[ 80.757] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5662 (res 42)
[ 80.757] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4660 (res 47)
[ 80.757] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 80.757] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[ 80.757] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left double triple
[ 80.757] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[ 80.757] (**) Option "TapButton1" "1"
[ 80.757] (**) Option "TapButton2" "2"
[ 80.757] (**) Option "TapButton3" "3"
[ 80.757] (**) Option "SoftButtonAreas" "50% 0 82% 0 0 0 0 0"
[ 80.757] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 80.757] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 80.810] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio2/input/input22/event20"
[ 80.810] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 17)
[ 80.810] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[ 80.810] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MaxSpeed is now 1.75
[ 80.810] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) AccelFactor is now 0.038
[ 80.810] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 80.810] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[ 80.810] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 80.810] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 80.810] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 80.811] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[ 80.811] (**) SynPS/2 Synaptics TouchPad: Ignoring device from InputClass "touchpad ignore duplicates"
[ 80.811] (II) config/udev: Adding input device PC Speaker (/dev/input/event16)
[ 80.811] (II) No input driver specified, ignoring this device.
[ 80.811] (II) This device may have been added with another device file.
[ 88.265] (II) NVIDIA(GPU-0): Display (Samsung SyncMaster (DFP-1)) does not support NVIDIA
[ 88.265] (II) NVIDIA(GPU-0): 3D Vision stereo.
[ 88.282] (II) NVIDIA(GPU-0): Display (Samsung SyncMaster (DFP-1)) does not support NVIDIA
[ 88.282] (II) NVIDIA(GPU-0): 3D Vision stereo.
[ 88.291] (II) NVIDIA(0): Setting mode "LVDS-0: nvidia-auto-select @1920x1080 +0+0 {ViewPortIn=1920x1080, ViewPortOut=1920x1080+0+0}, HDMI-0: 1680x1050_60_0 @1680x1050 +1920+0 {ViewPortIn=1680x1050, ViewPortOut=1680x1050+0+0}"
[ 89.221] (II) NVIDIA(GPU-0): Display (Samsung SyncMaster (DFP-1)) does not support NVIDIA
[ 89.221] (II) NVIDIA(GPU-0): 3D Vision stereo.
[ 90.639] (II) NVIDIA(GPU-0): Display (Samsung SyncMaster (DFP-1)) does not support NVIDIA
[ 90.639] (II) NVIDIA(GPU-0): 3D Vision stereo.
[ 93.745] (II) NVIDIA(GPU-0): Display (Samsung SyncMaster (DFP-1)) does not support NVIDIA
[ 93.745] (II) NVIDIA(GPU-0): 3D Vision stereo.
Notably, the following lines appear in the working case, but not the broken case:
[ 78.914] (II) Applying OutputClass "nvidia" to /dev/dri/card0
[ 78.914] loading driver: nvidia
Does anyone know what might be going on here?
Last edited by straemer (2014-12-20 13:03:58)

Hmmmm, that doesn't seem to be the issue. I have a nvidia geforce gtx 670mx. The nvidia website does link me to the 340xx driver for that card, but downgrading to that version still has the same issue. I suspect the issue is in Xorg, since it seems to load the module, but then decides it doesn't have a driver to run for some reason.

Cannot load nvidia driver module [SOLVED]

OK so for some reason I can no longer load the nvidia (proprietary) driver.
I have a laptop with optimus, on board intel and discrete nvidia GTX680M. I use this laptop for cuda development so I don't care about games etc, I just need the driver loaded to debug and run my cuda apps. bbswitch still works fine as does bumblebee which I don't use normally but I do have it setup and running in case. Also I didn't really work much on coding last week so not sure exactly when this started.
So here is what happens when I try to insert the nvidia module or use optirun:
$ sudo modprobe nvidia
modprobe: ERROR: could not insert 'nvidia': No such device
$ sudo insmod nvidia
insmod: ERROR: could not load module nvidia: No such file or directory
$ optirun -vv glxspheres
[ 27.485342] [DEBUG]Reading file: /etc/bumblebee/bumblebee.conf
[ 27.485506] [INFO]Configured driver: nvidia
[ 27.485635] [DEBUG]optirun version 3.2.1 starting...
[ 27.485642] [DEBUG]Active configuration:
[ 27.485645] [DEBUG] bumblebeed config file: /etc/bumblebee/bumblebee.conf
[ 27.485662] [DEBUG] X display: :8
[ 27.485674] [DEBUG] LD_LIBRARY_PATH: /usr/lib/nvidia:/usr/lib32/nvidia
[ 27.485676] [DEBUG] Socket path: /var/run/bumblebee.socket
[ 27.485679] [DEBUG] Accel/display bridge: primus
[ 27.485681] [DEBUG] VGL Compression: xv
[ 27.485684] [DEBUG] VGLrun extra options:
[ 27.485686] [DEBUG] Primus LD Path: /usr/lib:/usr/lib32
[ 27.560627] [INFO]Response: No - error: Could not load GPU driver
[ 27.560647] [ERROR]Cannot access secondary GPU - error: Could not load GPU driver
[ 27.560651] [DEBUG]Socket closed.
[ 27.560666] [ERROR]Aborting because fallback start is disabled.
[ 27.560671] [DEBUG]Killing all remaining processes.
I don't have an xorg file for the intel gpu.
device nodes are created:
$ ls /dev/ | grep nv
crw-rw-rw- 1 root root 195, 0 Sep 24 14:58 nvidia0
crw-rw-rw- 1 root root 195, 255 Sep 24 14:58 nvidiactl
log info:
$cat /var/log/Xorg.0.log | grep EE
[ 3.385] Current Operating System: Linux gpumonster 3.11.1-1-ARCH #1 SMP PREEMPT Sat Sep 14 19:30:21 CEST 2013 x86_64
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 4.299] Initializing built-in extension MIT-SCREEN-SAVER
[ 4.308] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 4.308] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 4.309] (EE) Failed to load module "fbdev" (module does not exist, 0)
$ cat /var/log/Xorg.8.log
[ 11367.762]
X.Org X Server 1.14.3
Release Date: 2013-09-12
[ 11367.762] X Protocol Version 11, Revision 0
[ 11367.762] Build Operating System: Linux 3.11.0-1-ARCH x86_64
[ 11367.762] Current Operating System: Linux gpumonster 3.11.1-1-ARCH #1 SMP PREEMPT Sat Sep 14 19:30:21 CEST 2013 x86_64
[ 11367.762] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=1c3a736e-6aab-45e1-a9ad-5d2f6195cd7d ro quiet
[ 11367.762] Build Date: 13 September 2013 01:28:59PM
[ 11367.762]
[ 11367.762] Current version of pixman: 0.30.2
[ 11367.762] Before reporting problems, check [url]http://wiki.x.org[/url]
to make sure that you have the latest version.
[ 11367.762] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 11367.762] (==) Log file: "/var/log/Xorg.8.log", Time: Thu Sep 19 23:04:24 2013
[ 11367.762] (++) Using config file: "/etc/bumblebee/xorg.conf.nvidia"
[ 11367.762] (++) Using config directory: "/etc/bumblebee/xorg.conf.d"
[ 11367.762] (==) ServerLayout "Layout0"
[ 11367.762] (==) No screen section available. Using defaults.
[ 11367.762] (**) |-->Screen "Default Screen Section" (0)
[ 11367.762] (**) | |-->Monitor "<default monitor>"
[ 11367.762] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 11367.762] (**) | |-->Device "DiscreteNvidia"
[ 11367.762] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 11367.762] (**) Option "AutoAddDevices" "false"
[ 11367.762] (**) Option "AutoAddGPU" "false"
[ 11367.762] (**) Not automatically adding devices
[ 11367.762] (==) Automatically enabling devices
[ 11367.762] (**) Not automatically adding GPU devices
[ 11367.762] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 11367.762] Entry deleted from font path.
[ 11367.762] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 11367.762] Entry deleted from font path.
[ 11367.762] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 11367.762] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 11367.762] Entry deleted from font path.
[ 11367.762] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 11367.762] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 11367.762] (++) ModulePath set to "/usr/lib/nvidia/xorg/,/usr/lib/xorg/modules"
[ 11367.762] (==) |-->Input Device "<default pointer>"
[ 11367.763] (==) |-->Input Device "<default keyboard>"
[ 11367.763] (==) The core pointer device wasn't specified explicitly in the layout.
Using the default mouse configuration.
[ 11367.763] (==) The core keyboard device wasn't specified explicitly in the layout.
Using the default keyboard configuration.
[ 11367.763] (II) Loader magic: 0x7fdc20
[ 11367.763] (II) Module ABI versions:
[ 11367.763] X.Org ANSI C Emulation: 0.4
[ 11367.763] X.Org Video Driver: 14.1
[ 11367.763] X.Org XInput driver : 19.1
[ 11367.763] X.Org Server Extension : 7.0
[ 11367.763] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 11367.763] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 11367.763] setversion 1.4 failed
[ 11367.764] (--) PCI:*(0:1:0:0) 10de:11a0:1558:5105 rev 161, Mem @ 0xf6000000/16777216, 0xe0000000/268435456, 0xf0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288
[ 11367.764] Initializing built-in extension Generic Event Extension
[ 11367.764] Initializing built-in extension SHAPE
[ 11367.764] Initializing built-in extension MIT-SHM
[ 11367.764] Initializing built-in extension XInputExtension
[ 11367.764] Initializing built-in extension XTEST
[ 11367.764] Initializing built-in extension BIG-REQUESTS
[ 11367.764] Initializing built-in extension SYNC
[ 11367.764] Initializing built-in extension XKEYBOARD
[ 11367.764] Initializing built-in extension XC-MISC
[ 11367.764] Initializing built-in extension SECURITY
[ 11367.764] Initializing built-in extension XINERAMA
[ 11367.764] Initializing built-in extension XFIXES
[ 11367.764] Initializing built-in extension RENDER
[ 11367.764] Initializing built-in extension RANDR
[ 11367.764] Initializing built-in extension COMPOSITE
[ 11367.764] Initializing built-in extension DAMAGE
[ 11367.764] Initializing built-in extension MIT-SCREEN-SAVER
[ 11367.764] Initializing built-in extension DOUBLE-BUFFER
[ 11367.764] Initializing built-in extension RECORD
[ 11367.764] Initializing built-in extension DPMS
[ 11367.764] Initializing built-in extension X-Resource
[ 11367.764] Initializing built-in extension XVideo
[ 11367.764] Initializing built-in extension XVideo-MotionCompensation
[ 11367.764] Initializing built-in extension XFree86-VidModeExtension
[ 11367.764] Initializing built-in extension XFree86-DGA
[ 11367.764] Initializing built-in extension XFree86-DRI
[ 11367.764] Initializing built-in extension DRI2
[ 11367.764] (II) LoadModule: "glx"
[ 11367.764] (II) Loading /usr/lib/nvidia/xorg/modules/extensions/libglx.so
[ 11367.773] (II) Module glx: vendor="NVIDIA Corporation"
[ 11367.773] compiled for 4.0.2, module version = 1.0.0
[ 11367.773] Module class: X.Org Server Extension
[ 11367.773] (II) NVIDIA GLX Module 325.15 Wed Jul 31 18:12:00 PDT 2013
[ 11367.773] Loading extension GLX
[ 11367.773] (II) LoadModule: "nvidia"
[ 11367.773] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 11367.773] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 11367.773] compiled for 4.0.2, module version = 1.0.0
[ 11367.773] Module class: X.Org Video Driver
[ 11367.773] (II) LoadModule: "mouse"
[ 11367.773] (II) Loading /usr/lib/xorg/modules/input/mouse_drv.so
[ 11367.773] (II) Module mouse: vendor="X.Org Foundation"
[ 11367.773] compiled for 1.14.0, module version = 1.9.0
[ 11367.773] Module class: X.Org XInput Driver
[ 11367.773] ABI class: X.Org XInput driver, version 19.1
[ 11367.773] (II) LoadModule: "kbd"
[ 11367.774] (WW) Warning, couldn't open module kbd
[ 11367.774] (II) UnloadModule: "kbd"
[ 11367.774] (II) Unloading kbd
[ 11367.774] (EE) Failed to load module "kbd" (module does not exist, 0)
[ 11367.774] (II) NVIDIA dlloader X Driver 325.15 Wed Jul 31 17:50:57 PDT 2013
[ 11367.774] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 11367.774] (--) using VT number 7
[ 11367.774] (II) Loading sub module "fb"
[ 11367.774] (II) LoadModule: "fb"
[ 11367.774] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 11367.774] (II) Module fb: vendor="X.Org Foundation"
[ 11367.774] compiled for 1.14.3, module version = 1.0.0
[ 11367.774] ABI class: X.Org ANSI C Emulation, version 0.4
[ 11367.774] (WW) Unresolved symbol: fbGetGCPrivateKey
[ 11367.774] (II) Loading sub module "wfb"
[ 11367.774] (II) LoadModule: "wfb"
[ 11367.774] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 11367.774] (II) Module wfb: vendor="X.Org Foundation"
[ 11367.774] compiled for 1.14.3, module version = 1.0.0
[ 11367.774] ABI class: X.Org ANSI C Emulation, version 0.4
[ 11367.774] (II) Loading sub module "shadow"
[ 11367.774] (II) LoadModule: "shadow"
[ 11367.774] (II) Loading /usr/lib/xorg/modules/libshadow.so
[ 11367.774] (II) Module shadow: vendor="X.Org Foundation"
[ 11367.774] compiled for 1.14.3, module version = 1.1.0
[ 11367.774] ABI class: X.Org ANSI C Emulation, version 0.4
[ 11367.774] (II) Loading sub module "ramdac"
[ 11367.774] (II) LoadModule: "ramdac"
[ 11367.774] (II) Module "ramdac" already built-in
[ 11367.774] (II) NVIDIA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 11367.774] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[ 11367.775] (==) NVIDIA(0): RGB weight 888
[ 11367.775] (==) NVIDIA(0): Default visual is TrueColor
[ 11367.775] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 11367.775] (**) NVIDIA(0): Option "NoLogo" "true"
[ 11367.775] (**) NVIDIA(0): Option "ProbeAllGpus" "false"
[ 11367.775] (**) NVIDIA(0): Option "UseEDID" "false"
[ 11367.775] (**) NVIDIA(0): Option "UseDisplayDevice" "none"
[ 11367.775] (**) NVIDIA(0): Enabling 2D acceleration
[ 11367.775] (**) NVIDIA(0): Ignoring EDIDs
[ 11367.775] (**) NVIDIA(0): Option "UseDisplayDevice" set to "none"; enabling NoScanout
[ 11367.775] (**) NVIDIA(0): mode
[ 11368.299] (II) NVIDIA(GPU-0): Found DRM driver nvidia-drm (20130102)
[ 11368.300] (II) NVIDIA(0): NVIDIA GPU GeForce GTX 680M (GK104) at PCI:1:0:0 (GPU-0)
[ 11368.300] (--) NVIDIA(0): Memory: 4194304 kBytes
[ 11368.300] (--) NVIDIA(0): VideoBIOS: 80.04.29.00.01
[ 11368.300] (II) NVIDIA(0): Detected PCI Express Link width: 16X
[ 11368.300] (--) NVIDIA(0): Valid display device(s) on GeForce GTX 680M at PCI:1:0:0
[ 11368.300] (--) NVIDIA(0): none
[ 11368.300] (II) NVIDIA(0): Validated MetaModes:
[ 11368.300] (II) NVIDIA(0): "nvidia-auto-select"
[ 11368.300] (II) NVIDIA(0): Virtual screen size determined to be 640 x 480
[ 11368.300] (WW) NVIDIA(0): Unable to get display device for DPI computation.
[ 11368.300] (==) NVIDIA(0): DPI set to (75, 75); computed from built-in default
[ 11368.300] (--) Depth 24 pixmap format is 32 bpp
[ 11368.300] (II) NVIDIA: Using 3072.00 MB of virtual memory for indirect memory
[ 11368.300] (II) NVIDIA: access.
[ 11368.304] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[ 11368.304] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
[ 11368.304] (II) NVIDIA(0): configuration option may not be set correctly. When the
[ 11368.304] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
[ 11368.304] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
[ 11368.304] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
[ 11368.304] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
[ 11368.304] (II) NVIDIA(0): Config Options in the README.
[ 11368.304] (II) NVIDIA(0): Setting mode "nvidia-auto-select"
[ 11368.308] Loading extension NV-GLX
[ 11368.312] (==) NVIDIA(0): Disabling shared memory pixmaps
[ 11368.312] (==) NVIDIA(0): Backing store disabled
[ 11368.312] (==) NVIDIA(0): Silken mouse enabled
[ 11368.312] (==) NVIDIA(0): DPMS enabled
[ 11368.312] Loading extension NV-CONTROL
[ 11368.312] (II) Loading sub module "dri2"
[ 11368.312] (II) LoadModule: "dri2"
[ 11368.312] (II) Module "dri2" already built-in
[ 11368.312] (II) NVIDIA(0): [DRI2] Setup complete
[ 11368.312] (II) NVIDIA(0): [DRI2] VDPAU driver: nvidia
[ 11368.312] (--) RandR disabled
[ 11368.316] (II) Initializing extension GLX
[ 11368.342] (II) Using input driver 'mouse' for '<default pointer>'
[ 11368.342] (**) Option "CorePointer" "on"
[ 11368.342] (**) <default pointer>: always reports core events
[ 11368.342] (WW) <default pointer>: No Device specified, looking for one...
[ 11368.422] (II) <default pointer>: Setting Device option to "/dev/input/mice"
[ 11368.422] (--) <default pointer>: Device: "/dev/input/mice"
[ 11368.422] (==) <default pointer>: Protocol: "Auto"
[ 11368.422] (**) <default pointer>: always reports core events
[ 11368.422] (**) Option "Device" "/dev/input/mice"
[ 11368.475] (==) <default pointer>: Emulate3Buttons, Emulate3Timeout: 50
[ 11368.475] (**) <default pointer>: ZAxisMapping: buttons 4 and 5
[ 11368.475] (**) <default pointer>: Buttons: 9
[ 11368.475] (II) XINPUT: Adding extended input device "<default pointer>" (type: MOUSE, id 6)
[ 11368.475] (**) <default pointer>: (accel) keeping acceleration scheme 1
[ 11368.475] (**) <default pointer>: (accel) acceleration profile 0
[ 11368.475] (**) <default pointer>: (accel) acceleration factor: 2.000
[ 11368.475] (**) <default pointer>: (accel) acceleration threshold: 4
[ 11368.475] (II) <default pointer>: Setting mouse protocol to "ExplorerPS/2"
[ 11368.769] (II) <default pointer>: ps2EnableDataReporting: succeeded
[ 11368.769] (II) LoadModule: "kbd"
[ 11368.769] (WW) Warning, couldn't open module kbd
[ 11368.769] (II) UnloadModule: "kbd"
[ 11368.769] (II) Unloading kbd
[ 11368.769] (EE) Failed to load module "kbd" (module does not exist, 0)
[ 11368.769] (EE) No input driver matching `kbd'
[ 11368.771] (II) config/udev: Adding input device Power Button (/dev/input/event6)
[ 11368.771] (II) AutoAddDevices is off - not adding device.
[ 11368.771] (II) config/udev: Adding input device Video Bus (/dev/input/event11)
[ 11368.771] (II) AutoAddDevices is off - not adding device.
[ 11368.771] (II) config/udev: Adding input device Video Bus (/dev/input/event9)
[ 11368.771] (II) AutoAddDevices is off - not adding device.
[ 11368.771] (II) config/udev: Adding input device Power Button (/dev/input/event5)
[ 11368.771] (II) AutoAddDevices is off - not adding device.
[ 11368.771] (II) config/udev: Adding input device Lid Switch (/dev/input/event3)
[ 11368.771] (II) AutoAddDevices is off - not adding device.
[ 11368.772] (II) config/udev: Adding input device Sleep Button (/dev/input/event4)
[ 11368.772] (II) AutoAddDevices is off - not adding device.
[ 11368.772] (II) config/udev: Adding drm device (/dev/dri/card1)
[ 11368.772] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 11368.772] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 11368.772] setversion 1.4 failed
[ 11368.772] (II) config/udev: Adding input device HP HP Link-5 micro dongle (/dev/input/event1)
[ 11368.772] (II) AutoAddDevices is off - not adding device.
[ 11368.773] (II) config/udev: Adding input device HP HP Link-5 micro dongle (/dev/input/event2)
[ 11368.773] (II) AutoAddDevices is off - not adding device.
[ 11368.773] (II) config/udev: Adding input device HP HP Link-5 micro dongle (/dev/input/mouse0)
[ 11368.773] (II) AutoAddDevices is off - not adding device.
[ 11368.773] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event12)
[ 11368.773] (II) AutoAddDevices is off - not adding device.
[ 11368.773] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event13)
[ 11368.773] (II) AutoAddDevices is off - not adding device.
[ 11368.773] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event14)
[ 11368.773] (II) AutoAddDevices is off - not adding device.
[ 11368.773] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event15)
[ 11368.773] (II) AutoAddDevices is off - not adding device.
[ 11368.774] (II) config/udev: Adding input device HDA Intel PCH Line Out (/dev/input/event16)
[ 11368.774] (II) AutoAddDevices is off - not adding device.
[ 11368.774] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event17)
[ 11368.774] (II) AutoAddDevices is off - not adding device.
[ 11368.774] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event18)
[ 11368.774] (II) AutoAddDevices is off - not adding device.
[ 11368.774] (II) config/udev: Adding input device BisonCam, NB Pro (/dev/input/event8)
[ 11368.774] (II) AutoAddDevices is off - not adding device.
[ 11368.774] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 11368.774] (II) AutoAddDevices is off - not adding device.
[ 11368.774] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event10)
[ 11368.774] (II) AutoAddDevices is off - not adding device.
[ 11368.775] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[ 11368.775] (II) AutoAddDevices is off - not adding device.
[ 11368.775] (II) config/udev: Adding input device PC Speaker (/dev/input/event7)
[ 11368.775] (II) AutoAddDevices is off - not adding device.
[ 11374.183] (II) UnloadModule: "mouse"
[ 11374.199] (II) NVIDIA(GPU-0): Deleting GPU-0
[ 11374.200] (EE) Server terminated successfully (0). Closing log file.
I'm not willing to give up and install/build the drivers from the cuda SDK just yet so any help would be greatly appreciated.
Last edited by tim (2013-10-02 08:20:49)

So in simple terms, the fix invovled ensuring the nvidia module is loaded before the bbswitch module. I'm not sure about the necessity of the things that follow but the fix may possibly also require removing bumblebee and possibly requires removing nvidia from repos and building the driver downloaded from nvidia.
This fix could be completely unrelated to the problems I was having with arch but I cannot verify the fix on arch specifically cos I installed every distro under the sun trying to get it all working and I got it to work on a non arch distro.
So... I'm not sure if I should really mark this a solved because I haven't/can't verify it on arch and technically the solution involved changing to another distro but in fact, I know it has absolutely nothing to do with arch since I saw the same behaviour on 3 other distros. If I have time, I will reinstall arch and verify but for the moment, I have a lot of work to catch up on now that I have a working nvidia driver I can actually use for dev
Anyway, what I think is going on is there is some bizarre issue with bbswitch that stops the nvidia driver from being found because on the current distro I have installed, if I have no bbswitch, no bumblebee and no nvidia modules loaded or services running etc. I can modprobe the nvidia driver and all works fine. I can then modprobe the bbswitch driver and that works too. IF I modprobe the bbswitch driver first and then modprobe the nvidia driver, I get this error that says the nvidia module cant be found. The location it prints is in some updates directory whcih is odd too because I installed from nvidia source and never installed updates at all and made sure that there were absolutely no repo nvidia drivers or updates etc.
Last edited by tim (2013-10-02 08:35:39)

NVIDIA driver 6md647ww does not install on W701 with Windows 7 64 Bit

Hello,
I have downloaded the nvidia driver 6md647ww (311.00), 64 bit version, and can't install on a Windows 7 64-bit system. It says "no compatible device found". The strange thing is, although the decompression routine and the window asking to start installation both say that they are the 64 bit version, the text besides the check mark "install the driver now" says it will install the 32 bit version (after decompressing the window says 64 bit in the upper part, but 32 bit in the lower part).
So I guess there is an error in the installation routine which erronously wants to install the 32 bit version although it is DEFINITELY the 64 bit version I have downloaded. Also, I downloaded for testing the 32 bit version of the driver (5md647ww), and if I try to install that, I get exactly the same error as with the 64 bit version.
Could someone please look into the 6md647ww, there is something wrong with it. Also, I can install 6md640ww and 6md643ww without any problems and switch between these two versions without any error - the 6md647ww issue is definitely NOT a problem of my OS configuration.
I have a sporadic heavy crash issue with 6md643ww and need to upgrade badly.
Please help. Best regards, Michael
System: Lenovo W701, 16 GB Ram, Windows 7 64 Bit, NVIDIA Quadro FX 3800M

In the meanwhile Rev 04 of the driver was published. This version is binary different to Rev 03 and - surprise - it now says correctly after unpacking it will install the 64-bit version. But after that same problem as before, "no compatible device found".
I did some searching into the files of 6md647ww. I guess the file Display.Driver\NVLT.inf contains a list of compatible devices - in this file the sections labelled NVIDIA_SetA_Devices.NTamd64.* list a lot of device-ids, for example PCI\VEN_10DE&DEV_0A3C&SUBSYS_214517AA and many more. The device id of the graphics card for a system can be found in the hardware/device manager of windows, I obtained that for my card and this id doesn't show anywhere in NVLT.inf. So if my guess is correct, it is no wonder the installer says "no compatible device" since the device id of my card is not listed in NVLT.inf.
Please note again that all previous versions of lenovo drivers for my NVIDIA Quadro FX 3800M did and do install without absolutely any problem!
This is strange, readme of the current driver version definitely says NVIDIA Quadro FX 3800M is supported by this driver, but the driver doesn't seem to contain the device id for it. Looks almost like the wrong driver was used / bundled into 6md647ww.
And again the question to the board / administrators if lenovo technical support is reading here and is there another contact at lenovo where I could direct my problem to? I am still having the sporadic heavy crash issue which is very dangerous since it can happen any time if displaying whatever graphics in whatever software and which therefore has a high risk of data loss. Also, installing the plain NVIDIA driver directly in the current version still has the problem of flickering and color errors, so this isn't a solution either.
Best regards, Michael

How to stop Nvidia driver errors on Bootcamp

Hi, I'm using a MacBook Pro mid 2010 with a Nvidia Drive fully updated on a Windows 8.1 x64 and it is constantly going black specially when using web browsers. If someone had the same problem and found a practical solution please help.

If it is a 15" model, than it should have two GPUs. Use the internal display and download gfxCardStatus. Ensure your are using the Intel GPU and test your browsers. If the screen issues are resolved, then nVidia (or driver) is suspect, otherwise I suspect the logic board.
You can also check the Mac Using Apple Hardware Test - Apple Support . It may not find all issues.

Both nouveau and nVidia driver problems with Stellarium

Stellarium v0.12.4 with either xf86-video-nouveau 1.0.9-1 or nvidia (latest driver) and an nVidia MCP78S (GeForce 8200) chip usually results in either distorted graphics and sometimes complete system lock-up.
The nVidia driver is worse, nouveau sometimes works but its a crap shoot. This has been going on for about 2 months now, and I have tested both drivers.
With nouveau it dumps these boot errors, but works on other software just fine:
Oct 21 17:17:48 eagle kernel: nouveau E[ PBUS][0000:02:00.0] MMIO read of 0x00000008 FAULT at 0x10022c
Oct 21 17:17:48 eagle kernel: nouveau E[ PBUS][0000:02:00.0] MMIO read of 0x00000008 FAULT at 0x100230
Oct 21 17:17:48 eagle kernel: nouveau E[ PBUS][0000:02:00.0] MMIO read of 0x00000008 FAULT at 0x1002e4
I cannot use the nvidia driver in general because it sometimes causes graphics faults when using Chromium.
I don't get any other graphics issues other than with Stellarium (and obviously I cannot run google-earth with nouveau either).
Any ideas on where to start with this problem would be appreciated.

Thanks for answering!
Following your advice, I downloaded and installed the latest driver from Nvidia (http://www.nvidia.fr/object/notebook-win7-winvista-64bit-260.99-whql-driver-fr.html). I'm not sure this is the one I updated on the first place since I don't remember when I did it (it was a few months ago, and as I had internet without using wi-fi, I didn't see that much the BSOD, but now that I'm back to wi-fi, the problem occurs often). Until now, no BSOD, but the first problem "Display Driver Stopped Responding and Has Recovered" is still here, and a little bit more annoying since it can occurs while watching some video files (it didn't happen before).
For the BIOS problem, it was the one described on the link you gave, but no the problem is over. I was just thinking it could be relevant to understand the others problems.
I'll let you know if the BSOD is (or seems) definitively gone. In the meantime, if someone knows how to fix the problem of the display driver that stopped responding and was recovered, it would be greatly appreciated!

Need to compile nvidia driver for a custom kernel [SOLVED]

I compiled a custom kernel following this wiki page: http://wiki.archlinux.org/index.php/Ker … rom_Source
I can boot into it just fine. I now want to compile an nvidia driver for use with it and followed the steps on this wiki page: http://wiki.archlinux.org/index.php/NVI … tom_kernel
I run into a problem when makepkg trys to compile it. Here is the output:
$ cd ~/devel/abs/nvidia/
$ makepkg -c
==> Making package: nvidia-my 190.42-1 x86_64 (Thu Nov 5 17:42:29 EST 2009)
==> Checking Runtime Dependencies...
==> Checking Buildtime Dependencies...
==> Retrieving Sources...
-> Found NVIDIA-Linux-x86_64-190.42-pkg0.run in build dir
==> Validating source files with md5sums...
NVIDIA-Linux-x86_64-190.42-pkg0.run ... Passed
==> Extracting Sources...
==> Entering fakeroot environment...
==> Starting build()...
Creating directory NVIDIA-Linux-x86_64-190.42-pkg0
Verifying archive integrity... OK
Uncompressing NVIDIA Accelerated Graphics Driver for Linux-x86_64 190.42..................................................................................................................................................
If you are using a Linux 2.4 kernel, please make sure
you either have configured kernel sources matching your
kernel or the correct set of kernel headers installed
on your system.
If you are using a Linux 2.6 kernel, please make sure
you have configured kernel sources matching your kernel
installed on your system. If you specified a separate
output directory using either the "KBUILD_OUTPUT" or
the "O" KBUILD parameter, make sure to specify this
directory with the SYSOUT environment variable or with
the equivalent nvidia-installer command line option.
Depending on where and how the kernel sources (or the
kernel headers) were installed, you may need to specify
their location with the SYSSRC environment variable or
the equivalent nvidia-installer command line option.
*** Unable to determine the target kernel version. ***
make: *** [select_makefile] Error 1
==> ERROR: Build Failed.
Aborting...
The step it's choking on is (from the PKGBUILD), "make SYSSRC=/lib/modules/${_kernver}/build module || return 1"
What am I doing wrong?
My PKGBUILD:
pkgname=nvidia-my
pkgver=190.42
_kernver='2.6.32-rc6-MINE'
pkgrel=1
pkgdesc="NVIDIA drivers for kernel26."
arch=('i686' 'x86_64')
[ "$CARCH" = "i686" ] && ARCH=x86
[ "$CARCH" = "x86_64" ] && ARCH=x86_64
url="http://www.nvidia.com/"
depends=('kernel26>=2.6.31' 'kernel26<2.6.32' "nvidia-utils=${pkgver}")
conflicts=('nvidia-96xx' 'nvidia-173xx')
license=('custom')
install=nvidia.install
source=("http://download.nvidia.com/XFree86/Linux-$ARCH/${pkgver}/NVIDIA-Linux-$ARCH-${pkgver}-pkg0.run")
md5sums=('f94806feee87de756d14fe3e9bcaf05a')
[ "$CARCH" = "x86_64" ] && md5sums=('ae431ff849ec01446e6724f9fcfe3bb4')
build() {
cd $srcdir
sh NVIDIA-Linux-$ARCH-${pkgver}-pkg0.run --extract-only
cd NVIDIA-Linux-$ARCH-${pkgver}-pkg0
cd usr/src/nv/
ln -s Makefile.kbuild Makefile
make SYSSRC=/lib/modules/${_kernver}/build module || return 1
mkdir -p $pkgdir/lib/modules/${_kernver}/kernel/drivers/video/
install -m644 nvidia.ko $pkgdir/lib/modules/${_kernver}/kernel/drivers/video/
sed -i -e "s/KERNEL_VERSION='.*'/KERNEL_VERSION='${_kernver}'/" $startdir/nvidia.install
My nvidia.install
post_install() {
KERNEL_VERSION='2.6.32-rc6-MINE'
depmod $KERNEL_VERSION
post_upgrade() {
post_install
rmmod nvidia || echo 'In order to use the new nvidia module, exit Xserver and unload it manually.'
post_remove() {
KERNEL_VERSION='2.6.32-rc6-MINE'
depmod $KERNEL_VERSION
Last edited by graysky (2009-11-07 10:54:33)

Hello,
I'm kind of a noob and am trying to get follow the directions from the Nvidia wiki on installing on a custom kernel. I'm trying to use the abs method to install on kernel26rt version 2.6.33rt. I followed directions exactly and am getting an error that I didn't find on any other posts. Can you please take a look? Here is my terminal:
[jsadural@jlinux nvidia]$ makepkg -ci
==> Making package: nvidia-2633rt 270.30-3 (Wed Mar 30 08:53:08 PDT 2011)
==> Checking runtime dependencies...
==> Checking buildtime dependencies...
==> Retrieving Sources...
-> Downloading NVIDIA-Linux-x86_64-270.30-no-compat32.run...
--2011-03-30 08:53:08-- ftp://download.nvidia.com/XFree86/Linux … mpat32.run
=> “NVIDIA-Linux-x86_64-270.30-no-compat32.run.part”
Resolving download.nvidia.com... 69.31.121.43
Connecting to download.nvidia.com|69.31.121.43|:21... connected.
Logging in as anonymous ... Logged in!
==> SYST ... done. ==> PWD ... done.
==> TYPE I ... done. ==> CWD (1) /XFree86/Linux-x86_64/270.30 ... done.
==> SIZE NVIDIA-Linux-x86_64-270.30-no-compat32.run ... 30037601
==> PASV ... done. ==> RETR NVIDIA-Linux-x86_64-270.30-no-compat32.run ... done.
Length: 30037601 (29M) (unauthoritative)
100%[======================================>] 30,037,601 696K/s in 42s
2011-03-30 08:53:50 (696 KB/s) - “NVIDIA-Linux-x86_64-270.30-no-compat32.run.part” saved [30037601]
==> Validating source files with md5sums...
NVIDIA-Linux-x86_64-270.30-no-compat32.run ... Passed
==> Extracting Sources...
==> Starting build()...
Creating directory NVIDIA-Linux-x86_64-270.30-no-compat32
Verifying archive integrity... OK
Uncompressing NVIDIA Accelerated Graphics Driver for Linux-x86_64 270.30........................................................................................................................
NVIDIA: calling KBUILD...
test -e include/generated/autoconf.h -a -e include/config/auto.conf || ( \
echo; \
echo " ERROR: Kernel configuration is invalid."; \
echo " include/generated/autoconf.h or include/config/auto.conf are missing.";\
echo " Run 'make oldconfig && make prepare' on kernel src to fix it."; \
echo; \
/bin/false)
mkdir -p /home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/.tmp_versions ; rm -f /home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/.tmp_versions/*
make -f scripts/Makefile.build obj=/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel
cc -Wp,-MD,/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/.nv.o.d -nostdinc -isystem /usr/lib/gcc/x86_64-unknown-linux-gnu/4.5.2/include -I/usr/src/linux-2.6.33-rt/arch/x86/include -Iinclude -include include/generated/autoconf.h -D__KERNEL__ -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Werror-implicit-function-declaration -Wno-format-security -fno-delete-null-pointer-checks -O2 -m64 -mtune=generic -mno-red-zone -mcmodel=kernel -funit-at-a-time -maccumulate-outgoing-args -fstack-protector -DCONFIG_AS_CFI=1 -DCONFIG_AS_CFI_SIGNAL_FRAME=1 -pipe -Wno-sign-compare -fno-asynchronous-unwind-tables -mno-sse -mno-mmx -mno-sse2 -mno-3dnow -Wframe-larger-than=2048 -fomit-frame-pointer -Wdeclaration-after-statement -Wno-pointer-sign -fno-strict-overflow -fno-dwarf2-cfi-asm -fconserve-stack -I/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel -Wall -MD -Wsign-compare -Wno-cast-qual -Wno-error -D__KERNEL__ -DMODULE -DNVRM -DNV_VERSION_STRING=\"270.30\" -Wno-unused-function -mcmodel=kernel -mno-red-zone -UDEBUG -U_DEBUG -DNDEBUG -DMODULE -D"KBUILD_STR(s)=#s" -D"KBUILD_BASENAME=KBUILD_STR(nv)" -D"KBUILD_MODNAME=KBUILD_STR(nvidia)" -c -o /home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.o /home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c
In file included from /usr/src/linux-2.6.33-rt/arch/x86/include/asm/uaccess.h:573:0,
from include/linux/poll.h:13,
from /home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv-linux.h:84,
from /home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:13:
/usr/src/linux-2.6.33-rt/arch/x86/include/asm/uaccess_64.h: In function ‘copy_from_user’:
/usr/src/linux-2.6.33-rt/arch/x86/include/asm/uaccess_64.h:35:6: warning: comparison between signed and unsigned integer expressions
In file included from /home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:13:0:
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv-linux.h: At top level:
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv-linux.h:251:35: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘nv_spinlock_t’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv-linux.h:1436:5: error: expected specifier-qualifier-list before ‘nv_spinlock_t’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c: In function ‘nv_alloc_file_private’:
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:1993:5: error: implicit declaration of function ‘semaphore_init’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:1994:5: error: ‘nv_file_private_t’ has no member named ‘waitqueue’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:1995:5: error: implicit declaration of function ‘atomic_spin_lock_init’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:1995:5: error: ‘nv_file_private_t’ has no member named ‘fp_lock’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c: In function ‘nv_kern_poll’:
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:2790:30: error: ‘nv_file_private_t’ has no member named ‘waitqueue’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:2793:5: error: implicit declaration of function ‘atomic_spin_lock_irqsave’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:2793:5: error: ‘nv_file_private_t’ has no member named ‘fp_lock’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:2804:5: error: implicit declaration of function ‘atomic_spin_unlock_irqrestore’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:2804:5: error: ‘nv_file_private_t’ has no member named ‘fp_lock’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c: In function ‘nv_kern_close_registry’:
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:3595:18: error: ‘nv_file_private_t’ has no member named ‘off’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:3611:22: error: ‘nv_file_private_t’ has no member named ‘off’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c: In function ‘nv_kern_write_registry’:
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:3703:51: error: ‘nv_file_private_t’ has no member named ‘off’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:3710:45: error: ‘nv_file_private_t’ has no member named ‘off’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:3720:9: error: ‘nv_file_private_t’ has no member named ‘off’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c: In function ‘nv_post_event’:
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:4330:5: error: ‘nv_file_private_t’ has no member named ‘fp_lock’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:4347:5: error: ‘nv_file_private_t’ has no member named ‘waitqueue’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:4348:5: error: ‘nv_file_private_t’ has no member named ‘fp_lock’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c: In function ‘nv_get_event’:
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:4362:5: error: ‘nv_file_private_t’ has no member named ‘fp_lock’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:4365:9: error: ‘nv_file_private_t’ has no member named ‘fp_lock’
/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.c:4390:5: error: ‘nv_file_private_t’ has no member named ‘fp_lock’
make[3]: *** [/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel/nv.o] Error 1
make[2]: *** [_module_/home/jsadural/devel/abs/nvidia/src/NVIDIA-Linux-x86_64-270.30-no-compat32/kernel] Error 2
NVIDIA: left KBUILD.
nvidia.ko failed to build!
make[1]: *** [module] Error 1
make: *** [module] Error 2
==> ERROR: A failure occurred in build().
Aborting...
thanks,
jason

Trouble with latest NVIDIA driver

Hi!
I just bought an NVIDIA card (9600GT) to replace my AMD Radeon HD 3650.
I installed the latest NVIDIA driver (180.22-1), and X now fails to start:
X.Org X Server 1.5.3
Release Date: 5 November 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.27-ARCH x86_64
Current Operating System: Linux zeus 2.6.28-ARCH #1 SMP PREEMPT Sun Jan 18 19:41:52 UTC 2009 x86_64
Build Date: 17 December 2008 10:46:49PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Fri Jan 23 19:41:58 2009
(==) Using config file: "/etc/X11/xorg.conf"
(EE) Failed to load module "type1" (module does not exist, 0)
/usr/bin/X: symbol lookup error: /usr/lib/xorg/modules/extensions//libglx.so: undefined symbol: _nv000002gl
giving up.
xinit: Connection refused (errno 111): unable to connect to X server
xinit: No such process (errno 3): Server error.
I've tried reinstalling xorg-server, libdrm nvidia, nvidia-utils and so on, but nothing helps.
Has anyone else experienced this issue?

I had the same problem My solution was ... After reinstalling every thing 3 times with no good results I decided to try one more time on a 64 bit version of it and it worked perfectly so I decided to try different distributions with 386 486 and 686 all the same problem.. it seems only the 64 bit distributions work well with the newest Nvidia cards.... Can't find a reason and Nvidia has not answer me yet....
Sorry but if you want your card working on Linux you will need to upgrade to 64 bit it seems.
also there is no Wine HQ for 64 bit under Arch other distros have but if you want it under Arch you will have to build it your self.
OK if some else knows better Please Please Let me Know the secret ... I tried 10 distros and 60 installations later I had these results, maybe I'm doing it all wrong.
PS:
I do a lot of beta testings Just for fun. Testing Jaunty and Windows 7 at this time and 7 is pretty but it stills Sucks Majorly Just as much as Vista does.
Jaunty Has no drivers for Nvidia and is no way to Install it manually with the idiot user proof thing that they got I'll be going back to Arch today and give it a rest to my frustrations For a While....

Nvidia driver doesn't recognize GTX 275

I've followed the steps on the wiki for the nvidia driver, but when I start X it does not recognize my GTX 275 card. I think the driver may simply not support this card yet (it doesn't according to nvidia). Can anyone confirm this? Does anyone know when a new driver will be released? Also, would the nouveau driver work temporarily until nvidia releases something?

We were having a similar issue. For some reason, the line that specifies which driver to use was not added to the xorg.conf file after installation. The steps shown above by deej are basically the same, but they add a lot of fluff to the xorg.conf file that may not be needed.
We were able to add it and get it to work by simply adding the following line to the xorg.conf file:
Section "Device"
Identifier "Doesn't matter what this says"
Driver "nvidia" <-- This is the line we added
EndSection
Don't know if this applies to this distro as well (we are running ubuntu), but we had to change the file /etc/default/linux-restricted-modules-common from this:
DISABLED_MODULES=""
To this:
DISABLED_MODULES="nv" <-- We had to restart after this step
We have not done thorough testing on our machines, but have three of them up and running properly now. We have several more machines to work on and I'll try and get the exact process we are using posted on here (ex. Modify filex, install drivers, modify filey, etc.).
Last edited by tineras (2009-07-17 13:59:59)

New nvidia driver 1.0-6106

I upgraded my nvidia driver to the newest version with nvidia-installer --upgrade. So far it compiles and works without any errors (GeForce 4, kernel 2.6.7, full pacman -Syu, etc.). There are some new things:
ftp://download.nvidia.com/XFree86/Linux … -guide.txt
ftp://download.nvidia.com/XFree86/Linux … README.txt
Latest info and support http://www.nvnews.net/vbulletin/forumdi … forumid=14
Maybe it's just too late but I think the module is twice as big as it was before (?):
nvidia 4815476 20
EDIT: 1024x768 mode for TV-Out doesn't work anymore. 800x600 is the highiest now. Still no explanation why... but for me at least it's not a problem since I'm not using twinview :-) (just decreased default tv screen resolution and font size for tv wm :-)). Some people also report problems with games. I've tested bzflag only and it worked as usually (no faster and no slower).

Settings prog is bugged? How? It's to early to check everything but I could sucessfully run nvidia-settings and for example add a shadow to mouse cursor :-) I don't use it to restore the settings and I don't think it's very useful at all except maybe for gamers so it's not a big deal.
As I said I'm not using twinview too - I'm running tv-out but as a second screen (standard xfree way to do this). The lower resolution is not a problem then. But people who are using twinview for their own reasons (like external monitors connected to notebooks, cloning crt on the tv, etc. etc.) should consider staying with the older drivers for some time. Maybe it's a bug and nvidia will release a new driver with 1024x768 on the tv enabled again? - That's just a warning and I suggest to backup your older nvidia arch package if someone is using it.

Regressions in new Nvidia driver?

After a system upgrade somewhat recently, I found my graphics not working as well as usual.
For one thing, mplayer was suffering horrendous tearing under all rendering modes. Previously, I'd been able to get the gl renderer to work well with vsync so that it had almost no tearing issues. After the upgrade, neither that, nor xv, nor anything else seemed to be capable of rendering smoothly.
For another thing, I was seeing some glitches with the models of some units in Starcraft 2 under WINE. SCVs developed huge spiky poles coming out of their elbows, and Spine Crawler's poles reached up unto infinity while their beaks floated unattached nearby. I also had a noticeably reduced framerate (more than usual) during big battles in the game.
Downgrading from version 2.70.30-1 to 2.60.19.36 of the Nvidia driver (all 3 components) fixed the problems, so that's what I'm using now. I don't like the idea of being trapped on an older version of their driver while I wonder whether the new one fixes my issues or not, but I figured I'd at least post in case other people were experiencing the problems.

I just reverted to the previous nvidia driver 260.xx because with the new 270 in [extra] my desktop hanged just at loading time. It even cannot load the icons nor the task bar.
I'm not using gnome3, just gnome2 and xorg 1.9. I've never put the [testing] repository.
Sergi
To revert to 260.xx, I just followed this wiki entry:
https://wiki.archlinux.org/index.php/Do … g_Packages
and everything is ok now.
thanks.
techmagyor wrote:
Also i want to confifm what Gusar says. I have gnom3 from testing (obviously also xorg 1.10) and nvidia 270.30 for a nvidia 445m and no problems. No xorg.conf but in /etc/X11/xorg.conf.d/20-nvidia.conf:
Section "Device"
Identifier "Default nvidia Device"
Driver "nvidia"
Option "NoLogo" "True"
Option "RenderAccel" "1"
Option "ConnectedMonitor" "DFP"
Option "TripleBuffer" "1"
Option "DamageEvents" "1"
# AC settings:
Option "RegistryDwords" "PowerMizerLevelAC=0x2"
# Battery settings:
Option "RegistryDwords" "PowerMizerLevel=0x3"
Option "OnDemandVBlankInterrupts" "1"
EndSection
sergi34, could you explain better what you did? thanks in advance

Lightroom diashow nvidia driver windows 7

Hallo,
Ich hatte dassselbe Problem mit XP und Vista; die Diashow in Lightroom ergiebt nur weisse Bildschirme. Dies wurde durch einen neuen Nvidia Driver behoben. Für Windows 7 und Sony Vaio ist kein neuer Driver erhältlich ???!!!.
Ist irgendeine Lösung vorhanden?
Vaio PCG-GRT996ZP, Nvidia FX5600
Danke für jede Hilfe, JPB

Quote from: Ruudt on 30-July-12, 15:45:49
I tried a GX600 and modified a driver for it (with laptopvideo2go.com website).
You can download it here:
faenl.msi.eu/index.php?dir=Notebook/GX600/&file=Nvidia_195.81_win7x64_graphics_driver_modified_for_GX600%28unofficial%29.zip
Please note that this is not officially supported and/or tested.
I cannot give any support on modified drivers.
I tested it on GX600 with a Geforce 8600M GT (DEV_0407, SUBSYS_3FAD1462) and it installed fine but haven't run any games or benchmarks.
I just wanted to say thank you for the great driver. I have tested it on a MSI gx600 with a fresh installation of Windows 7 and the Nvidia 8600M GT works great with it. I tried the drivers directly from Nvidia and it did not work, so your solution is the way to go.
Thank you.

Black Screen On Boot After Nvidia Driver

I just installed arch and went to install my nvidia driver right afterwards. I now boot up and after grub i get a black screen. I am 99 percent sure i know what this problem is and i have had somthing similar with gentoo. I have a sandybridge so i have my nvidia card and the intel hd graphics. i remember in gentoo i had to go in the kernel config and disable intel hd graphics . i dont know how i would go about doing this here as i am new . i really dont want a custom kernel.
Last edited by paulb787 (2012-06-18 09:25:03)

SEMI-SOlVED
if you have a sandybridge motherboard and have intel hd graphics on in your bios (Lucid). after the nvidia driver is installed udev seems to pick up the intel card at boot. Blacklist i915 and intel_agp to fix this problem.
what loads those modules udev? mkinitcpio? is there any way to have them both? like choice your primary video card? im sure if i had two monitors i would be able to boot up with the one pluged in to intel graphics and when X loads xinerma would work with both. i dont have dual monitors but it still would be nice to have an option. is there any sandybridge features in linux?
Thank You
Paul
Last edited by paulb787 (2012-06-18 09:28:46)

Udev[testing] breaks nvidia driver

Similar Messages

Maybe you are looking for