UDP broadcast traffic on port 4554 from Wireless Access Points

Hello,
I am seeing a lot of broadcast traffic coming from my AP541N-A-K9 access points at port 4554/UDP . I have 5 of these in a cluster. I cant seem to find anything in the manual in regards to this port traffic. Any help is apprecieted

Hi
I found this reference for this. As per this it is used for "internal use"
https://www.cisco.com/assets/sol/sb/WAP561_Emulators/WAP561_Emulator_v1.0.4.4/device_info.html
HTH
Rasika
**** Pls rate all useful responses ****

Similar Messages

UDP Broadcast Traffic from Cisco ASA

Hi,
I want to know that, like Cisco IOS Router, Does Cisco ASA pass the UDP Broadcast traffic e.g., TFTP etc...?
Any thoughts ???
BR,
Mubasher Sultan

Hi Mubasher,
Unlike the router the ASA does not forward any kind of broadcast packet (with the exemption of the DHCP broadcasts when DHCP Relay is enabled).
I understand that your DHCP server is providing here the IP address for your TFTP servers. I guess you are using DHCP option 150.
So if the DHCP server is on one interface and the client is on another you can configure DHCP Relay on your ASA.
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008075fcfb.shtml
In regards of the TFTP requests these will be normal unicast packets as Cadet said so just make sure that you have the proper ACLs and NAT rules for that.

Can I disable my Verizon Fios Router Wireless radio, connect it to a switch and use my airport express as my wireless access point connected to an in wall ethernet port?

Here's the deal. I have a Verizon Fios MI424WR router. My house has CAT5 throughout the house. The media panel is located in the garage. I want to take the Verizon Fios Router and cannot it in the media panel so I can connect a switch to it, that way, all my CAT5 can fire throughout the house. Verizon being Verizon decided to connect the router directly in the office.
Can I go this route (Router in media panel, switch cross connect to it) and use Airport Express, connected to one of the in-wall CAT5 ports in my house and then set it up as my wireless access point to provide wifi to my portable devices (iPad, iPhone, Macbook)? Is this possible? Will Airport Express comminicate with my verizon router via ethernet in-wall? Do I have to turn off the wireless radio in the Verizon router? Any help would be greatly appreciated!

That is right, by hard wired I was just making clear wired vs wireless attachment. AirPort family of devices will only act in a repeater mode with their own family members, not FiOS routers. they have to be wired to work.
There are some useful docs you can download from Apple, Support, Manuals, Peripherals, AirPort (just follow thos links from the Support button on the top bar):
Apple AirPort Networks
Designing AirPort Networks
AirPort Express Setup Guide
The last has a diagram of what you are trying to do, though without the house wiring, etc., but the basic principle.

How to setup a wrt54g router as a wireless access point to extend wifi signal from e3200

how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
any tips to avoid interfearance once setup?

You have to connect both with a cable.

Apple TV 2G (Airplay and Homesharing) can only stream from devices on the same wireless access point range??

connection:
40 Mbps Fiber Broadband connection using:
Devices:
1. Main Modem/router (AP1): Huawei HG8245 (provided by ISP) - Wireless enabled.
2. Remote Access point (AP2): Linksys/Cisco E3200 Wireless gigabyte router flashed with DD-WRT v24-sp2 (06/14/11) mini (Cascaded -wired- LAN to LAN from main modem).
3. Wireless Repeater to cover a dead spot (AP3): Linksys/Cisco E1000 wireless repeater.
4. Apple Tv (AT2G) with home sharing/airplay enabled.
5.( Ipad) with home sharing on itunes enabled.
6. Win7 (PC) using iTunes with Home sharing enabled.
all devices are updated to their latest firmware.
In order to cover a large 3 story house with Wifi. I had (AP1) is located on the first floor, while (AP2) is located in the basement floor directly wired by LAN to LAN with (AP1). (AP3) is located on the Ground floor away from the living room to repeat wireless network into the back yard. While (AT2G) is located in the living room on the ground floor right in the middle of both (AP1) + (AP2) while connected via Wifi.
Network SSID, security, passphrase and wireless settings of (AP2) are identical to (AP1) to create a single big LAN/WLAN roaming network where all devices connected to both wireless access points can find/share the others. As understood, it's refered to as bridging.
I have noticed that my iphone/ipad does not show the airplay button anywhere within the wireless network. it seems that the apple TV randomly choses to connect to the AP with stronger signal, or switch to the other in case of a reboot to one of them.
to elaborate further, if i was sitting in the living room (groundfloor), trying to airplay some you tube contents via Wifi to my Apple TV, i may not find the airplay button available all the time, i found out the reason is while i'm wirelessly connected to AP1, the Apple TV was connected to AP2 and both deviced cannot detect each others to enable my purpose. that goes the same for Home Sharing. only if my Ipad/PC and Apple Tv are on the same wireless AP. they would detect each others immediately.
although, the second AP (AP2) is suppose to extend my wireless network of the same subnet in which any device connected can be found.
After all sorts of trial and error tweaking my router/access point, I thought the problem would be due to the Linksys 3200 capability of bridging WLAN and lacks few protocols that enables my purpose. i have flashed the firmware to a DD-WRT, but again, problem was not solved.
I have not tried having my Apple Tv wired to either router/AP, but i assume it may work well if i do so. i still need to solve this wireless connection issue though.
Am i the only one with this problem, would there be something wrong with my setup?
Your feedback is highly appreciated.

You may or may not already have your network set up correctly, it's just that I can't tell from what you have said.
I have a main router provided by my ISP, I have several other Airport Extremes and Airport expresses connected by Ethernet, all set up to bridge the network created by the main router.
Each maker has their own settings, but bridging should be reasonably obvious. In simple terms my main router distributes IP addresses to all devices, the Airports bridge that network by passing these addresses to the devices from the main router. A base station that isn't in bridging mode will distribute its own addresses to the devices connected to it.
I don't really follow your next point.
instruction for configuration vary from manufacturer to manufacturer, the best course of action here is to refer to the manual. If everything is set up properly the addresses of everything on your network will have identical sets of numbers for the first 3 of 4 groups of numbers that make up an address, the last set must always be different. I think the part you are referring to with your DD-WRT is the option to have Ethernet and wifi bridged or not.
Some routers may be easier to configure than others, but generally speaking they should all work with the Apple TV. 5Ghz is less likely to suffer interference but it is much more likely to be blocked by solid objects, it may or may not be an advantage.

How can I get alerts if a Wireless Access Point has been disconneted from the network?

How can I get alerts if a Wireless Access Point has been disconneted from the network?
Is it possible to get alerts via email from the WLC or WCS if Access-Point has been removed from the network?
Thanks in advance.

Hi,
The below link will answer ur question!!
http://www.cisco.com/en/US/docs/wireless/wcs/7.0/configuration/guide/7_0event.html#wp1229996
Please dont forget to rate the usefull posts!!
Regards
Surendra

IOS 6.0.1 - Problems with certificate based authentication on wireless access point

Hi all
We are using iPad 2 as order terminals in our shops for about 5 months. Some of the iPads (the first who entered the field) started to cause problems now. These iPads are no longer able to keep long-term connection to the wireless access point in our stores. After selecting the SSID a successful authentication using the stored EAP-TLS certificate is performed (this can be seen in the log files of our wireless controller and by the IP adress that is given by DHCP). But within seconds the affected iPads opening up a captive portal page (empty, without contents) and separates the connection to the SSID after a short time again.
Affected are currently only iPads 2 with iOS 6.0.1, which were staged about 5 months ago. The newer devices with iOS 6.1+ connect without problems and open no captive portal page. The first cases occurred on the last Wednesday. Before that everything worked without difficulty. No modifications took place on the security structure. The numbers of affected devices increased until all iOS 6.0.1 were affected.
Access to other SSIDs (without use of certificates, by entering a key) for the devices is still possible (the devices does not open an captive portal page). The DHCP scope is not used up, so there are enough IP addresses available.
"Newer iPads" with an iOS of 6.1+ are are showing no problems on the same wireless access point, where the older devices are rejected. New and old devices use the same certificates and authentication mechanisms.
In the analysis of the issue, it turned out that the problem can be solved by an update to iOS 6.1.3. Subsequently, the iPads will be able to rebuild a connection with the access point, without a captive portal page.
Since the bandwidth is very narrow dimensioned in our stores, the communication of the iPads was severely restricted. Thus, the iPads are for exampleare accessible for the APNS but can not find iOS updates or check for their availability.
A comprehensive update to iOS 6.1.3 is currently excluded.
Does anyone knows this issue? What else can be done (except from updating)?

I will answer my own question in case it helps anyone else.
It would "seem" the ios 6 devices try the proxy and if that is not working they resort to the def gateway.
To Fix I did the following:
Brocade WIFI network has IPS and Advanced Firewall rules that seemed to be tthwarting some traffic, the iphones would then try the default gateway and be blocked at the FW.
I disabled the IPS and the Advanced Firewall Settings on the wifi as they are redundant to our main IPS and firewall that all traffic flows through anyway. I will tune it later, but when the CEO is demanding a fix "**** the security, full speed ahead"
Created some rues on the firewall to allow...
- IMAP-SSL (port993) outbound
- SMTPS (port 465) to yahoo servers outbound
- tcp port 587 to yahoo servers outbound
- https to akamai servers
Most http and https goes through the proxy as it should, BUT...
It seems that the akamai traffic allways ignores the wifi proxy settings and just heads straight for the default gateway. I suspect there is a bug in the icloud app?
Hope this helps someone else.
-Bo

1242AG Wireless Access Point - Cannot Get DHCP IP for BVI1 interface - Multiple SSIDs...

Hello,
I am attempting to set up three Cisco 1242AG Wireless Access Points with multiple SSID's. I used the web interface and directions online to set up the two networks I want and at least one of the networks work wirelessly.
However, I have two problems:
The first, which is the most important, is that the "management" interface, BVI1, doesn't get an ip address from our DHCP server. I set the VLAN 60 (which you'll see in the documenation below) to be the native VLAN on the device as well as on the switch that the device is connected to as well as other settings in the configeration file below. Because of this, I can only manage the device via the console port which would be a huge pain once all of the devices are mounted.
The second problem is that I am not sure how to get both wireless networks broadcasting their SSID's. I have to manually type in the SSID for the second wireless network I have which I would prefer I don't have to. Anyway I can enable broadcasting on all of the SSID's?
Thank you for your time.
Regards,
Christopher Koeber
Using 7916 out of 32768 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP-18.wesleysem.edu
enable secret {Number Here} {Encrypted Password Here}
enable password {Number Here} {Encrypted Password Here}
aaa new-model
aaa session-id common
dot11 syslog
dot11 vlan-name Kresge vlan 20
dot11 vlan-name Library vlan 30
dot11 vlan-name Public vlan 60
dot11 vlan-name Secure_Public vlan 70
dot11 vlan-name Secure_Seminary vlan 80
dot11 vlan-name Server_Room vlan 1
dot11 vlan-name Straughn vlan 40
dot11 vlan-name Trott vlan 10
dot11 vlan-name Web_Room vlan 50
dot11 ssid (Secure) Wesley Campus
vlan 80
authentication open
authentication key-management wpa version 2
wpa-psk ascii {Number Here} {WPA Key Here}
dot11 ssid Public
vlan 60
authentication open
mobility network-id 60
username Cisco password {Number Here} {Encrypted Password Here}
username admin privilege 15 secret {Number Here} {Encrypted Password Here}!
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 80 mode ciphers aes-ccm
ssid (Secure) Campus
ssid Public
mbssid
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio0.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
bridge-group 40 spanning-disabled
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio0.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface Dot11Radio0.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
bridge-group 80 subscriber-loop-control
bridge-group 80 block-unknown-source
no bridge-group 80 source-learning
no bridge-group 80 unicast-flooding
bridge-group 80 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption vlan 80 mode ciphers aes-ccm
dfs band 3 block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio1.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio1.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
bridge-group 40 spanning-disabled
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio1.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface Dot11Radio1.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
bridge-group 80 subscriber-loop-control
bridge-group 80 block-unknown-source
no bridge-group 80 source-learning
no bridge-group 80 unicast-flooding
bridge-group 80 spanning-disabled
interface FastEthernet0
ip dhcp client update dns
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
no bridge-group 254 source-learning
bridge-group 254 spanning-disabled
interface FastEthernet0.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
no bridge-group 10 source-learning
bridge-group 10 spanning-disabled
interface FastEthernet0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
no bridge-group 20 source-learning
bridge-group 20 spanning-disabled
interface FastEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
no bridge-group 30 source-learning
bridge-group 30 spanning-disabled
interface FastEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
no bridge-group 40 source-learning
bridge-group 40 spanning-disabled
interface FastEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
no bridge-group 50 source-learning
bridge-group 50 spanning-disabled
interface FastEthernet0.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
no bridge-group 70 source-learning
bridge-group 70 spanning-disabled
interface FastEthernet0.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
no bridge-group 80 source-learning
bridge-group 80 spanning-disabled
interface BVI1
ip address dhcp client-id FastEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
end

I am using a third party DHCP server which is our Windows Domain Controller. I have the ip helper-address set for the native vlan of the Access Point through a layer 3 distribution switch (a Catalyst 4506) that the current switch connects to.
I didn't see any event on the logs for the AP.
Let me know if I need to do something else.
Thanks.

AirPort Extreme used as a wired/wireless access point at same time?

Can the gigabit ethernet ports (wired connection) on the AirPort Extreme be used at the same time as the wireless-N connection when it is installed to a switch on an existing network as an access point? Will it still broadcast simultaneous Wireless-N dual band signals?
If both are yes, then do you have any other information regarding the cofiguration? Or helpful links that may help me? Thank You.

I have not yet purchased an airport extreme or even tried this. I have an existing network with a simultaneous wireless-N dual band router feeding a main switch. From the main switch I have cat5e wired gigabit connections to 4 PC's then two cat5e cables, each going to a small switch at seperate media centers.
I have one area that I have a single cat5e wire that can not get the wireless signal from the existing router. In addition to the wireless signal problem, I could use a couple extra gigabit ethernet connections to this same area, but can't pull any new cat5's to it.
I was told I needed to install a multi-gigabit-port wireless-N access point or install another switch with a single port wireless-N access point connected to it. As I looked into this, the dedicated wireless-N access points are wireless-N dual band but do not broadcast them simultaneously (it's either/or).
So I was wondering if I would benefit in any way by using the AirPort Extreme instead of the dedicated wireless access point recommended, and if it will give me what I need plus a simultaneous dual band wireless-N connection to the area? I don't know why the IT didn't recommend installing another router like I'm thinking? Don't know if it will even work? If it is a good idea or not? Don't want any conflict or networking problems to have to deal with just because I didn't listen and/or got the wrong item? What do you think?

An Error Occurred while trying to join "my wireless access point"

Hi,
I've been using wireless access for a year and never had a problem connecting.
But starting yesterday I get a +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
I have 2 Mac's and have no problem connecting with the other one. It’s just the IMac.
I tried everything including resetting router, changing password, adding a $ to the password, accessing without password, deleting the whole air port and create a new one, but still getting the same message.
I might need to add, while I was working with the IMac I didn’t use wireless for a few hours, but when I got back to my browser I noticed that I was connected to a different wireless service. (FONFREEINTERNET if it matters) I have no idea why, since I didn’t change it.
Anyways, I tried to switch back to my access point, but it wouldn’t let me. It’ll just give me the +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
Funny is when I use the FONFREEINTERNET access point the internet seems to work fine.
I could look up Google without a problem, but when I tried to connect to Facebook for example it won’t let me. Instead a FONFREEINTERNET page will pop up with some options on how to pay! (by minute/or day/or week…)
I get the strange feeling that they planted some kind of bug/virus!!!
I don’t know what else to do.
Anyone knows that problem? What can I do?
Any help is greatly appreciated!
I researched on FONFREEINTERNET, there’s a spot close to my house/guess that’s the one I used…
http://maps.fon.com/ ZIP CODE 904-0113 and you’ll see a coffee pod, which is about 2 minutes walk from my house.

Hello Tesserax,
I get the same error message again...
I tried the 3 suggested steps again, but unfortunately it did not work.
After a Restart, Sleep or just the awaking from Screensaver mode I’m disconnected from my wireless Network anymore.
Even if the Computer was asleep for just a second!
I am able to fix the problem temporarily with Network Preferences → Assist me → Diagnostics
Choose Airport → Choose network → Enter Password (Even if I check safe password it’ll ask me every time) → and than usually all lights on the left menu switch from red to green and I get the popup message “A Network Change has been detected. Your Internet seems to work fine.” (similar - I’m at work and don’t remember exactly)
And it works fine…until the screensaver comes on or it sleeps again
I have the Problem with my IMac and Mini but the IMac at least remembers my password…
Any Ideas
I’m connected through a Buffalo WZR2-G300N wireless router

WRT310N as a "Wireless Access Point"

Hello,
I am in the market for a wireless device to add to an existing subnet. I see many tutorials regarding routers as wireless access points, but I am not sure if this device will work.
My plan is to connect one of the switch ports to an existing switch and not use/configure the WAN port.
I would rather purchase a router then a true WAP do to the fact that it can also act as a router (should I need it later), whereas a WAP cannot.
Any thoughts on this is appreciated.

Well try upgrading the firmware of the router & keep on holding tightly
the reset button in such a way that power light is blinking on the
router & then do a complete network power cycle i.e., unplug the power
cables from the modem & from the router & then plug in the power cable
to the modem first once all the lights are solid green you could plug
in the power cable to the router & check out it will definately work!!
Open the setup page of router using 192.168.1.1 then put in the
password as admin...all you need to do is do the wireless settings such
as Radio Band Frequency to Standard 20 MHZ frequency,channel to 11.
Also,the advanced wireless settings to Beacon Interval=50,Frag
thres=2306 & Rts thres=2307 & then uncheck a Block Anonymous Internet
Requests & it will definately work!!!

Can WRT54G be setup as a Wireless Access Point?

Does anyone know how to setup a router (WRT54G) to connect to other routers using a wireless connection and function as either a wireless access point or another router using the main router for it's internet and network connection?

you cannot get the WRT to connect wireless to any device as it is an access point.
However this same thing will work wired. All you need to do is change the LAN ip of the WRT to 192.168.1.50 from 192.168.1.1 and disable the DHCP on the WRT.
Connect both devices LAN to LAN , do not use the internet port of the WRT.

Using WRT54GR as a Wireless Access Point only

I have a WRT610N as my main router. I want to use an existing WRT54GR purely as a wireless access point and ethernet switch. Any suggestions on how best to do that so I can still access the WRT54GR to make configuration changes? Right now I have the network functionality working by simply not using the Internet port on the WRT54G but by going to 192.168.1.1 I can only get to the WRT610N.

(Restarting this thread).
I made the change you suggested and statically assigned 192.168.1.200 to the WRT54GR. I can reliably access it through this IP address. I connected it to the rest of my network by using one of the 4 switch ports (not the Internet port). I disabled DHCP on it and configured the Wireless settings to be the same (same SSID and Security Settings) as my other wireless router.
What I'm finding is that devices in my house won't assoicate with it. I tried changing the SSID to a different value; devices were able to see the new SSID but when I entered the pasword they told me that no DHCP server could be detected. A wired device that I plugged into another of the 4 switch ports on the WRT54GR was able to pick up an IP address from the main router just fine so I know that basic connectivity is OK.
To achieve what I want (i.e. the WRT54GR just acts as a wireless base station to extend wireless coverage in the house), do I need to connect the WRT54GR to the rest of the network using the Internet port rather than a switch port? If so, what configuration settings do I need to set up so that all the devices can get their IP address from the main router?

Determining which wireless access point a computer is connected to?

Apologies if this is posted in the wrong forum...
I am working in a large open space where there are multiple overlapping wireless access points -- not Airports but from another vendor. Unfortunately, several computers are experiencing wireless performance and dropout issues. I think the problems may be because the laptops (both PCs and Macs) are connecting to a more distant access point across the open space which is more "line of sight" than the closer access point. We can't confirm this theory, however, because I can't pinpoint which access point we're connecting to. This is possible with a PC, but I can't find such a piece of software for my PowerBook. Is anyone aware of such a utility?
Thanks so much.
Brita

Air Traffic Control widget. Search the download section for this useful widget. This widget lists all wi-fi access points, shows what channel each one is on, what the signal strength is and some vendor information.
Whichever access point you are connected to is listed in italic on the list. I like the fact that it is a widget as it makes it very easy to access.

Converting a BEFW11S4 V.2 router to a wireless access point. Can it be done?

I recently upgraded my home wireless router to an N device. Now, I'd like to use my old B wireless router as an access point to improve coverage on my property. I'd like to place it in a location in my house too distant from the N router to connect it with a cable. Any way to configure the old B router as a wireless access point?
Thanks for any help you can give me.
Dave

yes..u can certainly configure the router as an AP ... follow the steps below :
1)connect the B-router's port 1 to once of the LAN ports of the N-router
2)access the B-router's web ui , using its ip address
3)configure the wireless settings....in case , you want to make a roaming wireless network , the wireless settings on both the router should be same
4)if the ip add of the N-router is 192.168.1.1 , then change the ip add of the B-router to 192.168.1.2 and disable its DHCP server ..

UDP broadcast traffic on port 4554 from Wireless Access Points

Similar Messages

Maybe you are looking for