UDPWritePacket error 65 No route to host for -64.168.0.104

Hi,
When ARD 3 is active I see a continuous stream of the above message in Console.
The IP belongs to VeriSign. Does anyone know what ARD is doing with VeriSign?
I hope this isn't a snoop.

I am seeing this as well, but it is for numerous addresses. The -64 appears to be an artifact somehow appearing instead of 192 (as in 192.168). So I would guess that the computer you're seeing issues with is 192.168.0.104.
On mine, I'm seeing it with lots of computers, which is why I know the above. They all start with "-64.168.1." which, if the -64 were a 192, would be my subnet scheme.
I just did a count, and in the past 10 minutes, I has 30 entries in my log... from six distinct IPs. I just went to look up what computers were at those IPs, and... they don't appear in my ARD scanner. So, I looked them up in my All Computers list, and it turns out that they are all laptops which are in "All Computers" but which are currently not on my LAN.
So I would hazard a guess that this is an innocuous log entry that is informing you that ARD is attempting to see if various computers in your list have shown up on the LAN since last time it looked for them.
To validate... is 192.168.0.104 on your LAN a laptop or otherwise unconnected machine?
Mac OS X (10.4.6)

Similar Messages

FTP receiver channel error: No route to host

Hello,
I am using a ftp receiver channel and got the following error:
java.lang.Exception: ftp access error: java.net.NoRouteToHostException: No route to host.
The following steps are processed right:
- Connection to FTP-Server "XXXX", Folder "/public_html/external/eh/"
- Write to FTP-Server "XXXX", Folder "/public_html/external/eh/", file "xyz.xml"
- Sending: Modus "TXT", Size XXX, Codepage UTF-8
And then the error occurs.
It seems that the channel could connect to the server and start sending the data, but then the error occurs.
Did anybody know this problem?
Thank you very much
Thomas

Hi Thomas -
Is your FTP server configured for active or passive data connections? If active, you need SP15. Before SP15, only passive data connections are supported.
Regards,
Jin

RMI connection Error: No route to host

hi all,
We are using RMI in our project and We are using different computers on LAN for
server and Client Component,
Both the computers use j2sdk1.4.2_03
But when the client runs it gives the following error:
:java.rmi.ConnectIOException: Exception creating connection to: gridlab26;
nested exception is:
java.net.NoRouteToHostException: No route to host: connect
In this scenario we are just retrieving a String from the server. this
works well on One PC using localhost.
we found that you have encountered such problem earlier and might have
resolved it.
if you have any idea how to correct this problem please help us.
thanks
[email protected]

hi,
yes both the PCs are pinging each other and we are able to share our things as well (with sharing n securiry facility in winXP)
if u hav any other suggestion plz convey me
tnx
Deep

No route to host for specific web site

Hi everyone,
since 3 week i can't access the site www.laurapuppato.it from my macbook pro.
Before this period I could access it, now browsers stand still.
If I make an nslookup it is resolved with the IP.
If I ping both the IP or the URL the result is:
ping laurapuppato.it
PING laurapuppato.it (5.28.58.30): 56 data bytes
Request timeout for icmp_seq 0
Request timeout for icmp_seq 1
Request timeout for icmp_seq 2
Request timeout for icmp_seq 3
ping: sendto: No route to host
Request timeout for icmp_seq 4
ping: sendto: Host is down
Request timeout for icmp_seq 5
ping: sendto: Host is down
Request timeout for icmp_seq 6
ping: sendto: Host is down
Request timeout for icmp_seq 7
ping: sendto: Host is down
Request timeout for icmp_seq 8
ping: sendto: Host is down
Request timeout for icmp_seq 9
If I try form my iphone in the same wireless connection it connects. If I try with another connection in another place the mac still doesn't connect while the iPhone has no problem.
What could it be the problem?
What I have to check also?
Thanks.

Yes i have restarted it some day ago.
The result of traceroute is this:
traceroute to 5.28.58.30 (5.28.58.30), 64 hops max, 52 byte packets
1 * * *
2 * *traceroute: sendto: No route to host
traceroute: wrote 5.28.58.30 52 chars, ret=-1
traceroute: sendto: Host is down
3 traceroute: wrote 5.28.58.30 52 chars, ret=-1
*traceroute: sendto: Host is down
traceroute: wrote 5.28.58.30 52 chars, ret=-1
*traceroute: sendto: Host is down
traceroute: wrote 5.28.58.30 52 chars, ret=-1
^C

NAT error: UDP OK but TCP = no route to host

I recently did a firmware update on my Airport Express and I think something has changed which is affecting file transfer speed. A NAT test shows UDP listen port 6881 is OK but when testing TCP listen port 6881 I get the following message:
NAT error: No route to host (173.19.148.196:6881)
I have Mediacom Cable and their provided modem is Touchstone Telephony Modem and my Airport Express is plugged into it to provide me a wireless connection (it has an IP address of 10.0.1.1).
I have a MacBook 4,1 Intel Core 2 Duo and run OS X v. 10.5.6. In Security settings my Firewall is OFF.
Can someone explain to me what I need to do to open the TCP port? Also, what is a UDP connection?
Thank you

i had the same problem.
and i did the following steps
on vuze program
1) vuze -> preferences -> incoming tcp listen port (example 50123)
2) set the same port on UDP
after that you have to open tcp protocol (NAT -> virtual server) ... on your router and set start port as the same port as you already set in vuze (ex. 50123)... and an end port (ex. 50124)
be careful as local ip address, you have to set the same ip in the tcp protocol settings with the ip that your macbook uses to connect to the internet. you can find the ip on system preferences --> web--> and get the information.
I hope to help you and others with the same problem!

Remote RSS Feed consumption - no route to host

Hi all, I tried to embed an external RSS feed but always get the error that Service SS_GET_PAGE and Function getRssFeedForUrl cannot be performed due to System Error : No route to host. I guess that the server needs a proxy setting in order to connect to the external proxy. I cannot figure out how to configure the content server to retrieve those external URLs. Is there a specific config file to set the proxy value or do I have to set the proper environment variable on Linux (that was my first guess but I did not succeed). Thanks for any hint.

That could mean one of two things: either the default route is not set on the host giving this error message or IP packets destined to the target host can not be routed due to network misconfiguration.

Print driver host for 32 bit applications has stopped working

I just bought a Hp ENVY 7640 printer. I cannot use the wireless printing on my 64 bit computer, with Windows 7. I get an error message "print driver host for 32 bit applications has stopped working". I have looked into all of your online support solutions and nothing I have tried has fixed the problem.

Was there any resolution to this issue? We have a user with the same issue. The details of the error are:
Problem signature:
Problem Event Name:                        APPCRASH
Application Name:                             splwow64.exe
Application Version:                           6.1.7601.17777
Application Timestamp:                     4f35fbfe
Fault Module Name:                          mxdwdrv.dll
Fault Module Version:                        0.3.7601.17514
Fault Module Timestamp:                  4ce7c883
Exception Code:                                  c0000005
Exception Offset:                                000000000004e891
OS Version:                                          6.1.7601.2.1.0.18.10
Locale ID:                                             1033
Additional Information 1:                  0f86
Additional Information 2:                  0f86ddcc0aa605af31ef1b7f5abedf57
Additional Information 3:                  539e
Additional Information 4:                  539e0f43d86d39f144fdb012e341ed8d

No route to host:connect -- error in the struts-config.xml file

hi all,
acutally am doing a struts application in that i have written everything properly
but getting this kinda no route to host:connect error
my struts-config.xml file is like this...
<struts-config>
<form-beans>
<form-bean name="myForm" type="MyForm">
</form-beans>
<action-mappings>
<action path="/action"
               name="myForm"
               type="MyAction"
               scope="request"
               validate="true" >
               <forward name="success" path="/success.jsp" />
               <forward name="failure" path="/failure.jsp" />
     </action>
</action-mappings>
</struts-config>
sikandar

Hi Lee,
I am working on Oracle ADF 10.1.2 and getting the same problem. The lines in my struts-config.xml are as below:
<action path="/unitsView" className="oracle.adf.controller.struts.actions.DataActionMapping" type="view.UnitsViewAction" name="DataForm" parameter="/unitsView.uix" unknown="false">
<set-property property="modelReference" value="unitsViewUIModel"/>
<forward name="unitsEditLink" path="/unitsEdit.do"/>
</action>
<action path="/unitsView" className="oracle.adf.controller.struts.actions.DataActionMapping" type="view.UnitsViewAction" name="DataForm" parameter="/unitsView.uix" unknown="false">
<set-property property="modelReference" value="unitsViewUIModel"/>
<forward name="unitsCreateLink" path="/unitsCreate.do"/>
</action>
I have two lines with [action path="/unitsView"]. The reason why is that I want the user to go to the form create screen for the create button and form edit screen for the edit button. If this does not work, it seems to mean that only a single screen can be used for create/edit functions. However, the ADF editor diagram looks perfectly to point to create.uix and edit.uix respectively.
Please shed some light.
Thanks,
Regards,
Michael

Test connection failed for resource(s): AD: == No route to host\n

Hi, First of all I would like to tell you that the application was running fine few days back, this issue has come suddenly.
I am getting following error while doing connection test for AD with SUN IDM:
Test connection failed for resource(s): AD: ==> No route to host\n
and when I try to open the detail for windows active directory arrow mark from the resource tab, Its giving me below error:
Error iterating over objects ==> com.waveset.util.WavesetException: ==>java.net.NoRouteToHostException: No route to host
I tried to google on this but all are pointing to some network/firewall problem.
Can anybody suggest me the correction ways to resolve this problem. Any idea how I can proceed further.
Thanks,
Jimmy

First of all, I dont know if you even done the proper fault elimination
No route to host is indicative of a network problem that could be based on several different faults.
Simplest way to check, log in to the system running your IdM.
first check if your nameservice is working
nslookup <your fully qualified hostname for the AD gateway>
idmmgr@unix103a:$ nslookup idm-gw.company.com
Server:         139.188.2.1
Address:        139.188.2.1#53
idm-gw.company.com canonical name = win050a.company.com.
Name:   win050a.company.com
Address: 171.39.88.145if you get the right response there
try pinging the returned address
idmmgr@unix103a:$ ping 171.39.88.145
171.39.88.145 is aliveIf you have a routing problem it will probably show above...
if the route to the gateway works, it might be the gateway that cant talk to the AD
Just follow the track manually and if it stops working from one point, go past that point (if you can) and see if it works beyond it.
Either way, whatever resource is pointed out in the connectinfo in the pertinent adaptor or connector should work from the prompt of the system running it, if not, then you can start unraveling it from there.

Error: can't fetch data for this host - too few bytes supplied by RPC

Hi,
In our internal Lab we have:
One Admin, Media,Client Server (we can make backups for himself) - Solaris 10 with DDS4 tape drive (lab)
One Windows Client (we can make backups) - Windows XP
One Linux Client - CentOS 5.1
When we add the linux client with the command:
mkhost -a ob --inservice -r client -k 1024 linux
We receive this message in the linux (host) /usr/tmp/observiced.log
Error: can't fetch data for this host - too few bytes supplied by RPC partner (OB cached object manager)
And in the obtool we receive (forever looping)
Info: waiting for host to update certification status...
Can you help us with this linux client error ? (iptables and selinux disabled!!)
Thanks in Advance
Serpins

[SOLVED]
Selinux not well removed....
Thanks in Advance
Serpins

Linux Error: 113: No route to host

After completeing 3.1 in the installation guide I jump down to chapter 4, but I can't get the web interface to work.
It doesn't matter how I access the URL, I've tried both http://localhost:8080/htmldb and http://realhostname:8080/htmldb/ with same result, no data at all, the connection is closed directly.
I've checked listener.log and found this:
02-NOV-2005 01:01:02 * http * (ADDRESS=(PROTOCOL=tcp)(HOST=10.8.0.22)(PORT=2556)) * handoff * http * 12518
TNS-12518: TNS:listener could not hand off client connection
TNS-12571: TNS:packet writer failure
TNS-12560: TNS:protocol adapter error
TNS-00530: Protocol adapter error
Linux Error: 113: No route to host
02-NOV-2005 01:01:23 * http * (ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=33183)) * handoff * http * 12518
TNS-12518: TNS:listener could not hand off client connection
TNS-12571: TNS:packet writer failure
TNS-12560: TNS:protocol adapter error
TNS-00530: Protocol adapter error
Linux Error: 113: No route to host
02-NOV-2005 01:02:54 * service_update * XE * 0
02-NOV-2005 01:03:01 * http * (ADDRESS=(PROTOCOL=tcp)(HOST=X.Y.Z.W)(PORT=33509)) * handoff * http * 12518
TNS-12518: TNS:listener could not hand off client connection
TNS-12571: TNS:packet writer failure
TNS-12560: TNS:protocol adapter error
TNS-00530: Protocol adapter error
Linux Error: 113: No route to host

Problem located (as usual after the 3 hours it took me to find the forum and post about it).
Using netstat and lsof I found that XE not only binds to 1521 and 8080, but also to port 33172 and since iptables blocks everything it got "No route to host".
The question is if 33172 is static or just a randomly chosen port number.

GoldenGate extract issue - TCP/IP error 113 (No route to host)

Hi All,
I have created a new replicat process on a new server. The old server is to be de-commissioned. after I created the replicat process on the new server (I copied the replicat prm file from the existing server - which is to be de-commissioned to new server and changed old encrypted password with new one and DISCARDFILE location), I modified the extract parameter file on source server. I changed RMTHOST and RMTTRAIL from older server name to new server name and old location to new location. once done , I stopped the extract and ran below command:
ADD RMTTRAIL /u01/app/ggs/dirdat/db, EXTRACT Ext1
and then started the extract process after which I am getting this error:
*2012-03-16 02:24:39 GGS ERROR 150 TCP/IP error 113 (No route to host).*
*2012-03-16 02:24:39 GGS ERROR 190 PROCESS ABENDING.*
I can very well ping both servers from both source and target. Any thoughts?
-Onkar

got the answer. It was firewall issue. When i turned the firewall down "service iptables stop", everything was smooth. I have raised request with the proper team to add the source ip in the target system firewall.
-Onkar

I am getting continuous "no route to host" errors

I am getting hundreds of these messages a day and my connections are very slow.
1/28/15 10:41:33.971 AM nsurlsessiond[179]: tcp_connection_destination_prepare_complete 3 connectx to 17.253.16.221:80@0 failed: No route to host
also at 69.164.12.53 and 8.27.250.126 and others.
Chrome is slow loading Google Mail and pages.
Just updated to 10.10.2, which didn't help.
Model Name: Mac mini
Model Identifier: Macmini6,2
Processor Name: Intel Core i7
Processor Speed: 2.3 GHz
Number of Processors: 1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 6 MB
Memory: 16 GB
Boot ROM Version: MM61.0106.B03
Ethernet:
Type: Ethernet
BSD Device Name: en0
Hardware (MAC) Address: a8:20:66:12:59:5a
IPv4:
Configuration Method: DHCP
IPv6:
Configuration Method: Automatic
DNS:
Server Addresses: 2001:4860:4860::8888, 2001:4860:4860::8844
Proxies:
Exceptions List: *.local, 169.254/16
FTP Passive Mode: Yes

Are there any other devices on your network, and if so, are they having Internet problems? If you haven't already done so, please restart the router (and the broadband adapter, if they're separate.)

External services moved, but SOA suite still gives "no route to host"

We have a SOA Suite integrating towards external services. The external service provider moved the services to a different server, and updated dns entries to reflect this move. But our SOA Suite gave "no route to host" errors when this move was performed, clearly not reloading the changes done in DNS, but still using the old address.
How and where can the SOA Suite be configured to actually time out domain name resolutions, when external services are moved this way. Can we ask it to use hostname instead of ip address.
Bouncing the servers is of course working, but there must be a configuraiton way around this.
bouncing production servers is the final resort.
Details of error message
<MSG_TEXT>BusinessEvent diapatch failed for {ESBDomain.Service.publish} with error An unhandled exception has been thrown in the ESB system. The exception reported is: "oracle.tip.esb.server.common.exceptions.BusinessEventRetriableException: An unhandled exception has been thrown in the ESB system. The exception reported is: "org.collaxa.thirdparty.apache.wsif.WSIFException: exception on JaxRpc invoke: HTTP transport error: javax.xml.soap.SOAPException: java.security.PrivilegedActionException: javax.xml.soap.SOAPException: Message send failed: No route to host: connect

also check for firewalls on the server - a good test would be to an attempt to telnet into webservice hostname and portnumber from the SOA Server.
Regards,
Shanmu.

URGENT : Error: nca_connect_server: cannot communicate host ...on port....

URGENT : Error: nca_connect_server: cannot communicate host ...on port....
Platform :
front end - Forms6i
App Server - Oracle 9iAS
Testing tool - Mercurry Load Runner 8.0
Database - Oracle 9i
Hi Gurus,
I am trying to run a script in Load runner but its always coming out by following error message -
vuser_init.c(63): Warning: ifError expired (5) during NCA handshake,
vuser_init.c(63): Warning: ifError expired (5)
vuser_init.c(63): Error: nca_connect_server: cannot communicate with host 202.46.209.42 on port 7778
Abort was called from an action.
forms url which used in test script is running fine without any error with same port, I am wondering why it is returning error with Load Runner ?
Quick help on pinpointing the issue will be highly appreciated, Following is the Loadrunner script m using -
vuser_init()
     web_set_max_html_param_len("1024");
     web_url("f6isrvl",
          "URL=http://202.46.209.42:7778/f6i/f6isrvl?config=devjp10_en",
          "Resource=0",
          "RecContentType=text/html",
          "Referer=",
          "Snapshot=t1.inf",
          "Mode=HTML",
          EXTRARES,
          "Url=../forms60java/f60web.jar", "Referer=", ENDITEM,
          "Url=../forms60java/FImageBean.jar", "Referer=", ENDITEM,
          "Url=../forms60java/images.jar", "Referer=", ENDITEM,
          LAST);
     web_url("Registry.dat",
          "URL=http://202.46.209.42:7778/forms60java/oracle/forms/registry/Registry.dat",
          "Resource=0",
          "RecContentType=text/plain",
          "Referer=",
          "Snapshot=t2.inf",
          "Mode=HTML",
          LAST);
     web_reg_save_param("NCAJServSessionId",
          "LB=",
          "RB=",
          "Search=Noresource",
          LAST);
     web_url("f6isrvl_2",
          "URL=http://202.46.209.42:7778/f6i/f6isrvl?config=devjp10_en&acceptLanguage=en-us&ifcmd=startsession",
          "Resource=0",
          "RecContentType=text/plain",
          "Referer=",
          "Snapshot=t3.inf",
          "Mode=HTML",
          EXTRARES,
          "Url=f6ilsnr/?JServSessionIdf6i=i7yjfl33c1.f45nez95eiGIpR1vp2TD/knGnluImQXHcALJmQ5Go6XNr3CSa30R&ifcmd=getinfo&ifhost=MILDH0417&ifip=10.81.6.127", "Referer=", ENDITEM,
          "Url=../forms60java/oracle/ewt/dataSource/OneDDataSourceListener.class", "Referer=", ENDITEM,
          "Url=../forms60java/oracle/ewt/dataSource/OneDDataSource.class", "Referer=", ENDITEM,
          "Url=../forms60java/oracle/ewt/dataSource/ArrayOneDDataSource.class", "Referer=", ENDITEM,
          "Url=../forms60java/oracle/ewt/dataSource/AbstractOneDDataSource.class", "Referer=", ENDITEM,
          "Url=../forms60java/oracle/ewt/dataSource/OneDDataSourceAdapter.class", "Referer=", ENDITEM,
          "Url=../forms60java/oracle/ewt/dataSource/OneDDataSourceEvent.class", "Referer=", ENDITEM,
          LAST);
     nca_set_connect_opt(SCALE_INFO, 8, 20);
     nca_set_connect_opt(REQUIRED_LIST, 0);
     nca_connect_server("202.46.209.42", "7778", "module=ulgprc_em_100_01_c.fmx userid=dbk/dbk@dbkls05 ORA_USER=devjp10 USR_LANG=ENG");
     nca_set_window("Login");
     nca_edit_set("27", "SSC");
     nca_obj_type("27", '\t', 0);
     nca_edit_set("30", lr_decrypt("44b61ad9b8d2295c3768adc952f4"));
     nca_button_press("32");
     nca_message_box_press("Forms", 2);
     nca_menu_select_item("SSC", "Lending;Underwriting");
     nca_set_window(" (Underwriting)(Pending Request : 0)");
     nca_button_set("386", 1);
     nca_menu_select_item(" (Underwriting)(Pending Request : 0)", "Edit;Exit");
     nca_set_window("SSC");
     nca_menu_select_item("SSC", "File;Exit");
     return 0;
Execution Log
Virtual User Script started
Starting action vuser_init.
vuser_init.c(12): web_set_max_html_param_len was successful      [MsgId: MMSG-26392]
vuser_init.c(14): Downloading resource "http://202.46.209.42:7778/forms60java/f60web.jar" (specified by argument number 9)      [MsgId: MMSG-26577]
vuser_init.c(14): Downloading resource "http://202.46.209.42:7778/forms60java/FImageBean.jar" (specified by argument number 12)      [MsgId: MMSG-26577]
vuser_init.c(14): Downloading resource "http://202.46.209.42:7778/forms60java/images.jar" (specified by argument number 15)      [MsgId: MMSG-26577]
vuser_init.c(14): web_url("f6isrvl") was successful, 1882891 body bytes, 1386 header bytes, 12 chunking overhead bytes      [MsgId: MMSG-26385]
vuser_init.c(27): web_url("Registry.dat") was successful, 4117 body bytes, 367 header bytes      [MsgId: MMSG-26386]
vuser_init.c(36): Registering web_reg_save_param was successful      [MsgId: MMSG-26390]
vuser_init.c(42): Downloading resource "http://202.46.209.42:7778/f6i/f6ilsnr/?JServSessionIdf6i=i7yjfl33c1.f45nez95eiGIpR1vp2TD/knGnluImQXHcALJmQ5Go6XNr3CSa30R&ifcmd=getinfo&ifhost=MILDH0417&ifip=10.81.6.127" (specified by argument number 9)      [MsgId: MMSG-26577]
vuser_init.c(42): Downloading resource "http://202.46.209.42:7778/forms60java/oracle/ewt/dataSource/OneDDataSourceListener.class" (specified by argument number 12)      [MsgId: MMSG-26577]
vuser_init.c(42): Downloading resource "http://202.46.209.42:7778/forms60java/oracle/ewt/dataSource/OneDDataSource.class" (specified by argument number 15)      [MsgId: MMSG-26577]
vuser_init.c(42): Downloading resource "http://202.46.209.42:7778/forms60java/oracle/ewt/dataSource/ArrayOneDDataSource.class" (specified by argument number 18)      [MsgId: MMSG-26577]
vuser_init.c(42): Downloading resource "http://202.46.209.42:7778/forms60java/oracle/ewt/dataSource/AbstractOneDDataSource.class" (specified by argument number 21)      [MsgId: MMSG-26577]
vuser_init.c(42): Downloading resource "http://202.46.209.42:7778/forms60java/oracle/ewt/dataSource/OneDDataSourceAdapter.class" (specified by argument number 24)      [MsgId: MMSG-26577]
vuser_init.c(42): Downloading resource "http://202.46.209.42:7778/forms60java/oracle/ewt/dataSource/OneDDataSourceEvent.class" (specified by argument number 27)      [MsgId: MMSG-26577]
vuser_init.c(42): Warning -26652: Response body length (96) does not match the Content-Length header specification (95) for "http://202.46.209.42:7778/f6i/f6isrvl?config=devjp10_en&acceptLanguage=en-us&ifcmd=startsession"      [MsgId: MWAR-26652]
vuser_init.c(42): web_url("f6isrvl_2") highest severity level was "warning", 4459 body bytes, 3017 header bytes      [MsgId: MMSG-26388]
vuser_init.c(59): nca_set_connect_opt("SCALE_INFO")
vuser_init.c(61): nca_set_connect_opt("REQUIRED_LIST")
vuser_init.c(63): Warning: ifError expired (5) during NCA handshake,
vuser_init.c(63): Warning: ifError expired (5)
vuser_init.c(63): Error: nca_connect_server: cannot communicate with host 202.46.209.42 on port 7778
Abort was called from an action.
TIA,
Sheilesh

Well, the obvious question is what does 'mail.wbe-pli.com' translate to on the machine?
Does it translate to your public IP address, in which case your traffic has to go out through your router and come back in? In addition to not being ideal, that's also not supported by a number of different routers (they can't handle NAT traffic coming back in from the private network).
In most cases the solution is to setup internal DNS so that your hostname maps to the internal address of your server, not the external one.
In this case, though, you could also configure Mail.app to use 'localhost' for the mail server, rather than 'mail.wbe-pli.com'. That will enable it to talk to the server running on the local system.

UDPWritePacket error 65 No route to host for -64.168.0.104

Similar Messages

Maybe you are looking for