UEFI PXE wont boot. very basic setup it should work

Hi all.
I am having problems booting Uefi PXE .
The client is a VM running in ESXi
WDS/SCCM Server is VM running ESXi
DHCP is VM running ESXi.
All VMs are on the same Host and Same Vswitch.
Dhcp option 60 = PXEClient
Option 66 = *ip address of WDS/SCCM*
Option 67 = /SMSBoot/x64/wdsnbp.com
Whit the above option i can boot Legacy clients via PXE fine .but not UEFi.
I read some where i must change the Option 67 = /SMSBoot/x64/wdsmgfw.efi
Which still does not work for me.
This setup should work as the Client server and dhcp are on the same broadcast domain.
Yes i have advertisements for All unknown Systems, and the OU of the computer.
What am i missing ?
when i try to boot a VM with EFI i get error PXE-E21

Yes, those options are not recommended, use of IP helper is advisable:
http://blogs.technet.com/b/configurationmgr/archive/2011/01/05/troubleshooting-the-pxe-service-point-and-wds-in-configuration-manager-2007.aspx

Similar Messages

I have a powerbook G-4 15 inch, It wont boot up and the display only works on the first try. it gets to the apple screen and freezes, when i try to restart theres no display. Help please, whats the issue here?

I left it running over night, it was running perfectly, in the morning the screen was black. i tried to restart it and got no display but i can hear the machine running. so i put away for several months, plug it in, charge the battery, it boots, i have a display, it loads the desktop and freezes. when i try to restart it theres no display. the last time i tried, i started it, i got to the apple screen and nothing. whats the issue here? please help.

Will it boot OK in Safe Mode? See What is Safe Boot, Safe Mode? (Mac OS X)
http://docs.info.apple.com/article.html?artnum=107392 Takes a while to run, but it usually "fixes" problems.
Safe Boot takes longer than normal startup
http://support.apple.com/kb/TS1884?viewlocale=en_US
Resolve startup issues and perform disk maintenance with Disk Utility and fsck
http://docs.info.apple.com/article.html?artnum=106214
 Cheers, Tom

NAC - wanna test the basic setup - does not work !!!!

SCENARIO :
·         I have simple NAC setup with 1 NAC MGR “CAM” and 1 NAC SRVR “CAS”
·         My users are running network 192.168.10.x/24 , and I wanna implement in L2 VG mode. Both NAC MGR and NAC SRVR can ping each other.
·         CAM VLAN 55 = 192.168.55.x/24 , and CAS VLAN 66 = 192.168.66.x/24
·         NAC MGR “CAM” has only 1 cable going to the core switch and NAC SRVR has 2 cables going to the core switch ( one is trusted trunk end and another is untrusted trunk end) . Created two VLANS 999 and 998 and put each of them on each link as blackhole prevention mechanism described in Cisco docs.
·         I have a Windows 2008 DHCP Server who is giving the pool of IPs for users from 192.168.10.x/24 and it is working fine. Routing in the core switch is also ok.
·         I have SSH and web access to both CAM and CAS boxes. They are also updating online smoothly.
·         From the GUI, I have created the AV Rules also and CAM shows CAS as connected as well !!!! My version is 4.1.8 (upgraded from 4.1.3 )
INT VLAN 10 (USER VLAN) SVI is on core switch = 192.168.10.254 /24
INT VLAN 55 ( MGMT ) SVI is on core switch = 192.168.55.254/24
INT VLAN 66 (MGMT) SVI is on core switch = 192.168.66.254/24
PROBLEM :-
1.       I am not able to download or get the NAC Client software MSI or stub file or ActiveX prompt to download ….
2.       I don’t know how to start troubleshooting at this stage. Please note that My client PC is windows XP machine and the port is already configured to VLAN 100.
I have 1 CORE switch only and my NAC boxes and client are connected to the same CORE switch.

VLANS Mapping is done in CAM, i didnt find any field in CAS...
Also, i am copying the switch port configs... ( a simple logical connectivity diagram was attached also to this discussion already )
VLANS DATABASE
==============
vlan 10
name AuthVLAN
vlan 11
name TEST_VLAN_USER
vlan 55
name NAM_mgmt
vlan 998
name DummyVLAN998
vlan 999
name DummyVLAN999
*** Only SVI is VLAN 10 with network = 192.168.11.x/24 , there is no SVI for VLAN 11 ***
Following ports are configured as follows :-
============================================
interface GigabitEthernet2/9
description ** NAS's untrusted interface **
switchport
switchport trunk native vlan 999
switchport trunk allowed vlan 11
switchport mode trunk
no ip address
interface GigabitEthernet2/10
description **** NAS Mgmt interface IP 192.168.66.1 *****
switchport
switchport trunk native vlan 998
switchport trunk allowed vlan 10,66
switchport mode trunk
no ip address
interface GigabitEthernet2/11
description *** Test User Acess Port ***
switchport
switchport access vlan 11
switchport mode access
no ip address
interface GigabitEthernet2/12
description ***** Connected to Eth0 NAM on IP 192.168.55.1 ***
switchport
switchport access vlan 55
switchport mode access
no ip address
spanning-tree portfast
spanning-tree bpduguard enable
*** FROM THIS core switch I can ping 192.168.66.1 and also 192.168.55.1 with comfort ***
** Please note that actual IPs are 192.168.x.y and not 10.10.x.y respectively

Very basic question -- Diagnostic not working.

I am trying to use JMF for the first time. I am using Windows 2000 and I have installed the JMF package (the generic one, not the Windows enhanced version because I need to work with multiple OS). I set my CLASSPATH in the Windows Control Panel. However, whenever I run the diagnostics, I am getting a JMF classes not found error. The CLASSPATH is set, does anyone have any other ideas what might be happening?

I've got Windows XP and I installed the all-platform version of JMF. I unzipped the package and copied
* all the files under \lib into my <JRE>\lib\ext\ directory (where <JRE> is e.g. "C:\Program Files\Java\j2re1.4.2_04") and
* all the files under \bin into <JRE>\bin and
then I got the following from the diagnostic program:
"JMF Version... 2.1.1e
All Java Build
Native Libraries Not Found"
which is just as it should be. For some reason, I do not need to have the jmf.jar set in my CLASSPATH. In fact, I dont have CLASSPATH set at all. Maybe it's a change they made in how the newer versions (1.2+) of appletviewer work?
Below is an excerpt from http://java.sun.com/products/java-media/jmf/reference/faqs/index.html#jmf2-a-error explaining the situation a bit.
=================
Q: What is this error?
java.lang.NoClassDefFoundError: javax/media/ControllerListener
This happens in two situations:
* jmf.jar is not in your CLASSPATH
* jmf.jar is in your CLASSPATH but you are using the JDK 1.2+ appletviewer.
JDK 1.2 and later require standard extensions to be loaded from <JDK>/jre/lib/ext directory. When you install JMF 2.1.1 <on Windows), it will automatically install the jmf.jar in the above mentioned directory. If for some reason it did not, or you installed JDK 1.2 or later after installing JMF, then you need to manually copy the jmf.jar and sound.jar files to the <JDK>/jre/lib/ext directory.
=================

Satellite A300 wont boot up

Hi guys
Im overseas atm, so I really want to try and resolve this problem by myself.
Ok I was watching a movie yesterday and as it ended the laptop locked up, it wouldnt let me ctr,alt,del nothing....
So I waited a few mins and tried again to ctr,alt,del again still frozen. SO I hit the power button for a few seconds and shut it down that way. When it rebooted I chose safe mode but when I was prompted for my password the keyboard wouldnt work so I couldnt type it in.
I had to use my external mouse and shut it down from the power option.
The next time it rebooted i chose normal mode but it has been sitting on the vista screen just before the password box pops up for hours.
Is there anything i can do guys???
Thanx John

Hi Akuma,
I tried what you said but to no avail.
After it restarted it got stuck on the Vista screen again, after about 20 mins I gave up.
I tried safe boot, restoring to previously saved point.
Nothing works it just wont boot up, one minute is was working fine the next its dead.
Toshiba said to do a system restore or something like that which basically takes it back to when it was brand new, so I loose everything.....

UEFI PXE BOOT ERROR

Hi,
I've a problem with the UEFI PXE in SCCM 2012R2.
My DHCP configuration:
Option 66 : myserveripaddress
Option 67 : SMSBoot\x64\wdsmgfw.efi
Option 60 : support
When I try to boot the machine (Hp Pro x2 612) the PXE starts but I receive the error:
Windows Deployment Services encountered an error:
Error Code: 0x102
Any Help is appreciated :)

It depends on what devices you are configuring. See here for configuring IP Helper on Cisco IOS
http://www.gerryhampsoncm.blogspot.ie/2013/02/sccm-2012-sp1-step-by-step-guide-part_9487.html
Here is an example from a Cisco switch:
interface Vlan10
ip address 172.16.112.254 255.255.255.0
ip helper-address 172.16.1.1
End
This allows clients booting in 172.16.112.0/24 subnet to find the ConfigMgr or MDT server (172.16.1.1).
It's very straightforward. Your networking chaps will have no issue.
Gerry Hampson | Blog:
www.gerryhampsoncm.blogspot.ie | LinkedIn:
Gerry Hampson | Twitter:
@gerryhampson

Help with Project Management setup from very basics...

hi all!
i am new to e-business suite and now i have installed vision demo database successfully on a Quad Core with 320 GB hard and 4 GB ram...now i need help to setup Project Management (PM) module for a hypothetical construction company with the required functionalities (just limited functionalities and Not complete functionalities as in EBS).i need help in setting up Project Management module from the very basics...so can you help me out in this...thanks in anticipation

Hi,
Please post only once (do not post same thread across multiple forums).
help with Financials setup from very basics...
Re: help with Financials setup from very basics...
Regards,
Hussein

Satellite A30 wont boot up and is stuck on "exiting PXE ROM"

A30 wont boot up and is stuck on a loop
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM.
I dont have recovery discs and bios does not allow to turn off any relevant settings.

The error message PXE-E61: Media test failure, check cable appears because the notebook tries to boot from the LAN.
There could be a different reason why the notebook doesnt boot from the HDD or from another source.
Firstly the wrong booting order could prevent the notebook from HDD booting.
Secondly the missing HDD or an HDD malfunction could cause this issue.
You should definitely try to access the BIOS pressing the F2 button immediately after notebook starting. There you should check if the HDD was recognized.
If not, then I recommend replacing the HDD and to reinstall the OS.
Best regards

Satellite A135-S2386 wont boot, no display at all, shows very little signs of life.

I received a customers computer today. It worked, but they had a problem with the BIOS password, so they asked us to reset it. The battery was pulled and it was left unplugged for a few hours to be worked on later. Now when the laptop is powered on, it wont boot at all... Here is what happens:
Press the power button, and the LED above it turns yellow (I used to own this same model, and I could have sworn my light was blue and not yellow. Can anyone confirm?)
The fan spins up for a few seconds and then stops.
The power indicator on the front of the laptop is green.
When turned on the HD light flashed once quickly, and then never lights up again.
The CD-ROM light is constantly orange, and the tray will not open. There is no media inside.
There is absolutely no display (not even a flicker) and external monitors don't work either.
No beep codes, even without the RAM and HD.
I have tried:
Removing RAM and harddrive
Resetting CMOS (this was the goal to begin with)
Leaving it unplugged and with no battery while holding the power for one minute, then plugging in.
Booting from USB.
At first I thought it was a problem with the GPU, but I don't even think it is getting a chance to display anything. Is the MOBO fried? I find it strange that all of the sudden it breaks when I get my hands on it (makes me look bad too) but I know these things are notorious for things like this. I also find it strange that the CD-ROM is constantly lit and wont open. I am thinking of trying to boot without it connected to see what happens. Any other suggestions?

Have you solved your problem? How?
I have the same problem.

I have a Imac 8,1 That wont boot.

I have a Imac 8,1 that wont boot.
3.06Ghz, Nvidia 8800
I believe i have 2 problems.
First this is what ive already done:
I ran an extensive hardware test, no problem
In disk utility I erased my harddrive and clean installed Mavericks,
Verified and repaired disk, no problems
Verified and repaired permissions, no problems
Disk boots up fine when running on MacBookPro through Firewire
Zapped PRAM/NVRAM plenty
After upgrade I can no longer boot into safe mode, Stalls after 25%
Can no longer use CMD-R
Can no longer use Apple Hardware Test
Doesnt seem like I can update firmware from disk by holding down the power button. not sure im using the right disk either.
These problems probably stem from running complex graphics on a windows 7 partitions I used to have.
     First off I think my GPU is out. I get Thick Green lines down the screen that are not from screen damage straight from startup.
After Chime the apple logo pops up and loads but after a while the wheel stops and the computer will reboot moments after. Im hoping this is a Firmware problem and I dont have to replace my GPU. My computer has booted up with the lines before and I dont think its the cause for not booting but im no professional. Before I updated to Mavericks This Problem already existed. Can a failing GPU cause boots to fail?
     During hardware test the green lines would go away and I would have a clean screen.
I loaded Mavericks from a USB drive from there onto the newly erased harddrive (32 Write erase). Everything was going great until I got close to the end of the loading bar for the setup and it froze. The colors on my screen displayed everything but with the colors messed up into a rainbow oval on the top half of the screen. I rebooted and suddenly I cant boot from anything. Harddrive, Install Disk, or USB
     So I plugged up my firewire and got on a MacBookPro with Mavericks and erased the disk again. Then I installed Mavericks flawlessly and it will boot from the MacBookPro but not from the Imac.
When I boot in Verbose mode I get an error that says
BootCacheControl: Unable to open /var/db/BootCache.playlist:2 no such file or directory
Then
NVDAStartup: Official (im guessing thats my GPU)
and a bunch of SMC:smcReadKeyAction ERRORS
and Sandbox: authd(##) deny file-write & deny file-read errors
Im thinking I need a new GPU but I want to be absolutely certain before I spend anything on replacing parts.
Could this be a EFI Firmware Problem?
like a Firmware/boot data problem from a bad ESP (I dont know what is what really).
If all this is part of the GPU it would totally make sense to just go ahead and replace it if thats the case. But im no expert, What do you think?

Very simple take it to an Apple Store or AASP and have it professionally diagnosed. Anything else would be guessing. Do NOT spend a penny on it until it is professionaly diagnosed otherwise you stand and excellent chance of throwing good money after bad.

975x wont boot - new parts

Hi all, im new to this forum but it seems great, i read around abit and found some useful posts.
However, i have the following setup :
Msi 975x
c2d 6400
2gb corsair xms 6400 c4 ( 2*1gb )
7900gs PoV
Aspire 550 psu
I just put the parts toghether again, after having the parts returned to vendor, he claims the first cpu didnt work, and returned the motherboard while i waited for a new cpu to arrive. When i got it i tried the system again, but the following error is still there ;
The system wont boot, other than the fans will spin up but no screen at all, just stands there, when i use the usb led thingy, it shows 4 red dots.
I saw some posts about OCZ memory that wont work, but those were reported as memory issues by the led if im correct, and as i can see it arent 4 red dots the code for CPU , or can the code be wrong and its still the memory ?
The new cpu i got was in an unopened box so it was really new, but i refuse to believe i have broken 2 cpus or have recieved 2 dead cpu from vendor.
Any ideas would be very much welcome.
Cheers // Baboon

Baboon,
You're not the only one surprised.
I bought THREE 975X PUEs and every time I have re-visited the MSI website I have found new caveats for something the board won't do, or for something that won't work, or for something not included . . . no fixes, mind you, just oddly worded "escape clauses".
Here are some examples:
MSI Reminds You...
• DDR2 800 needs to work with Intel Conroe CPU with FSB1066.
• The default memory frequency is DDR2 667, you can set to 800 in BIOS settings.
• Due to the BIOS limits, the Intel RAID and the JMicron RAID functions can not be enabled at the same time, which will cause the system unable to boot up.
• The RAID setup floppy disk is optional depending on the districts. You can download the files from the website to make the setup disk.
• To enhance IDE transfer speed, you may install JMicron IDE/SATA Driver. You may download the driver by clicking the "Driver" icon at the left side.
• The floppy disk cable will be optional.
Yep, the first one was a big surprise to a lot of us sticking in our P4s. Hello? Well, OK, maybe the "CPU Support Chart" should have been the "CPU Semi-Support Chart".
OK, I'll even give MSI the first one. But the third bullet! Now that one just flat makes me laugh!
Beta Board! MSI didn't design this Board, it just kinda "happened".

648max wont boot!

my 648max wont boot if i set my bios to auto for my ram timing and cpu fsb.
im using kingmax333mzh ram. but if i overclock a bit on this mobo to 105mzh and the memory timing to 4:5=157, it will boot.
but once i shutdown and turn on again my PC, a message apprear saying that my CPU is running in deferent FSB. but if i let it be, it will still boot and running in perfect. but if i enter again the bios setup then restart, all my bios will reset to default by it self. then i have to redo all my steps from the very first start~~~~
pls help lah~~~~~

Quote
Originally posted by chinsc
my 648max wont boot if i set my bios to auto for my ram timing and cpu fsb.
im using kingmax333mzh ram. but if i overclock a bit on this mobo to 105mzh and the memory timing to 4:5=157, it will boot.
but once i shutdown and turn on again my PC, a message apprear saying that my CPU is running in deferent FSB. but if i let it be, it will still boot and running in perfect. but if i enter again the bios setup then restart, all my bios will reset to default by it self. then i have to redo all my steps from the very first start~~~~
pls help lah~~~~~
i already try the 1.1 bios~~ nothing change!

Satellite L300 wont boot up

Hi, I have a Satellite L300 Laptop which since i dropped it , wont boot up i have tried the built in recovery but it stops with "Windows cannot recover Master file table". It is running Vista , does any one know how i can reboot my laptop as at the moment it starts then i get a blank screen and nothing .
Cheers Doug

You more than likely damaged the hard drive when you dropped it. See if it will boot to a CD or DVD. If it does you need to test the hard drive to see if it is usable or not.
To test the hard drive determine what brand of hard drive you have. You can check the Bios/Setup to find out. Go to that manufacturer's support site and download their Self Booting Diagnostic CD ISO image, create the CD using the Burn From Image option (see http://iso.snoekonline.com/iso.htm for more information on doing this), then boot to it and run the most exhaustive tests available. If you have a Toshiba drive you will need to use the Hitachi Drive Fitness Test as Toshiba doesn't supply their own. http://www.hitachigst.com/hdd/support/download.htm
If you don't post your COMPLETE model number it's very difficult to assist you. Please try to post in complete sentences with punctuation, capitals, and correct spelling. Toshiba does NOT provide any direct support in these forums. All support is User to User in their spare time.

[SOLVED] arch wont boot after triple boot experiment

Hi,
I cannot boot into arch anymore after installing ubuntu to another partition on my hard drive.
I used grub to dual boot arch and windows, but i need to use ROS and there are no working packages for arch so i tried to install ubuntu on another partition and triple boot.
Somhow my arch got broken by the ubuntu setup.
Windows still boots fine.
I already chrooted (to arch) from a live cd and reinstalled grub and did
grub-mkconfig -o /boot/grub/grub.cfg
, after that ubuntu appeared in the grub selection menu but arch still wont boot.
Arch boot hangs after checking /dev/sda6 for errors (arch partition), i cannot type or ctrl+shift+fx to another terminal
Anybody has an idea what got broken by ubuntu and how i can repair arch?
thanks!
samy
Last edited by Samy (2013-09-09 11:27:09)

Hey so i chroot again following this artikle: https://wiki.archlinux.org/index.php/Change_Root
then i did
pacman -Syyu mkinitcpio linux udev
and restarted
I tried starting arch again and it seemed to still not work, this time i gave it some more time and it actually booted.
It took very long though (more then 3 minutes or so)
in journalctl if found those lines:
Sep 09 04:20:00 meanarchy kernel: USB Video Class driver (1.1.1)
Sep 09 04:21:25 meanarchy systemd[1]: Job dev-disk-by\x2duuid-12027d8a\x2dd4b0\x2d4559\x2daa1c\x2de3ea5ca8f5bb.device/start timed out.
Sep 09 04:21:25 meanarchy systemd[1]: Timed out waiting for device dev-disk-by\x2duuid-12027d8a\x2dd4b0\x2d4559\x2daa1c\x2de3ea5ca8f5bb.device.
Sep 09 04:21:25 meanarchy systemd[1]: Dependency failed for /dev/disk/by-uuid/12027d8a-d4b0-4559-aa1c-e3ea5ca8f5bb.
Sep 09 04:21:25 meanarchy systemd[1]: Starting Swap.
so it seems boot is searching for some disk device 1:25 minutes before it fails.
I think i know the reason: I resized the Partition of arch while installing ubuntu this changes the uuid of the partition, now something is waiting for this disk to become ready because it still has the old uuid written somwhere.
UUIDs really suck, they are not human readable and always have problems with them if i touch my partitions.
Last edited by Samy (2013-09-09 11:27:45)

Imac wont boot it did till i changed inernet protocol all i get is apple and gear spinng

I have an 800mgz imac when I got it it booted up just fine i changed the internet from dial up tp broadband save it turn it off to connect broadband now it wont boot all i get is the apple logo and the spinning gear?

Another thing that you could try it is deleting or copying to desktop the preference files for networking. Mac OS will regenerate these files. You would then need to reconfigure your network settings.
While this discussion provides a solution for a different problem. I believe the files would be the same for all network configuration problems.
http://discussions.apple.com/message.jspa?messageID=8185915#8185915
http://discussions.apple.com/message.jspa?messageID=10718694#10718694
You need to get into single use mode for steps one and two that are listed below.
This page will tell you how to get into single user mode.
http://support.apple.com/kb/HT1492
Basically, you hold down the command-s key then powering on your machine. The command key has a little apple symbol on the lower left. It is between the alt/option key and the space bar. On a PC keyboard, it will be the windows key, I think.
( Do you know Unix. You are in a Unix single user console. ) The setup commands you need should be listed on the screen. For Mac OS 10.4.11, the commands are:
# Type the follow two instructions to access the startup disk in read/write:
/sbin/fsck -fy
/sbin/mount -uw /
The mv command is also the rename command. move within a directory.
basically :
mac $ cd /Library/Preferences/SystemConfiguration
/Library/Preferences/SystemConfiguration
mac $ ls
NetworkInterfaces.plist com.apple.nat.plist      preferences.plist
mac $ pwd
/Library/Preferences/SystemConfiguration
mac $ mv NetworkInterfaces.plist NetworkInterfaces.plist2
mac $ mv com.apple.nat.plist com.apple.nat.plist2
mac $ mv preferences.plist preferences.plist2
mac $
Here is an overview of the terminal commands. Lets assume that your account has a short user name of mac.
Macintosh-HD -> Applications -> Utilities -> Terminal
#What is my short user name? Type the whoami command.
mac $ whoami
mac
mac $
#How to list all of your disks.
# The ls command is for list
mac $ ls /Volumes/
Audio CD       Macintosh-HD   Spotless       Tiger-ext
mac $
# Let's say your flash drive is named Spotless
# cd is change directory
mac $ cd /Volumes/Spotless
# pwd is print working directory
mac $ pwd
/Volumes/Spotless
mac $
# The ls command is for list # l is long # F is type of file where / is directory mac $ ls -lF
total 134704
-rw-r--r--     1 mac staff     64560 Mar 3 2009 A-picture-of-Youpi-key.png
drwxr-xr-x    83 mac staff      2822 Nov 7 14:52 Applescript files/
drwxrwxrwx    12 mac staff       408 Dec 13 2008 Christmas Cards/
drwxr-xr-x     9 mac staff       306 Dec 21 17:39 Christmas Cards 2009/
... trimmed ... What does all this mean?
drwxrwxrwx
d = directory
r = read
w = write
x = executeable program
drwxrwxrwx
| | |
| |   all other users not in first two types
| |
| group
|
owner
Every Unix resource: files, folders, etc has an owner, group, other
a file has one owner.
a file has one group. A group contains a list of users.
To gain access to a file. You can be the owner, in the group, or not being the owner or in the group you ended up as other. Each of these categories has read, write, or execute permissions.
# l is long
# a is all to show hidden files & folders
mac $ ls -lFa
total 134736
drwxr-xr-x    41 mac   staff      1496 Dec 22 17:11 .
drwxrwxrwt     8 root admin       272 Dec 24 13:55 ..
-rwxrwxrwx     1 mac   staff     15364 Dec 23 12:52 .DS_Store*
drwx------     4 mac   staff       136 Jan 22 2009 .Spotlight-V100
drwxrwxrwt     5 mac   staff       170 Sep 14 16:36 .TemporaryItems
d-wx-wx-wx     4 mac   staff       136 Dec 31 1969 .Trashes
-rw-r--r--     1 mac staff     64560 Mar 3 2009 A-picture-of-Youpi-key.png
drwxr-xr-x    83 mac   staff      2822 Nov 7 14:52 Applescript files
drwxrwxrwx    12 mac   staff       408 Dec 13 2008 Christmas Cards
drwxr-xr-x     9 mac   staff       306 Dec 21 17:39 Christmas Cards 2009
... trimmed ...
# mv is move or rename
mv -i the-name the-new-name
# You can just rename the file back to what it was with mv command.
mv -i old-name new-name
Here is what these commands mean:
cd is change directory
pwd is a print working directory
ls is list
sudo is Super user do
mv is move or rename
For cryptic comments, you can always uses the manual command which is man. For example:
man mv
# Type the letter q to quit.
In case you have spaces in your filenames or directories, you need to escape them. See examples:
mac $ ls -l ~/"see it"
-rw-r--r-- 1 mac staff 3171 Oct 26 23:38 /Users/mac/see it
mac $
mac $ cd /Users/mac/Desktop/ttt\ html\ copy/
Do you know about tabing? Type in a few letters of a name then press the tab key. The computer will type out the rest of the name if it is unique.
Press the up arrow key to see the previous command(s).
To edit a command, use the left arror key to more left and the right arror key to move right. Use the delete key to delete the key to the left. Type a letter to insert.
history to see many previous commands.
mac $ history
    2 man launchd.conf
    3 history
Lots of links: http://discussions.apple.com/thread.jspa?threadID=2692161&tstart=0
http://discussions.apple.com/thread.jspa?threadID=2692161&tstart=0
Robert

UEFI PXE wont boot. very basic setup it should work

Similar Messages

Maybe you are looking for