UK-based LabVIEW Contractor

Available for LabVIEW consulting or turn-Key development., both on and offsite.
Certified LabVIEW Developer
National Instruments Alliance Partner
E mail for more information/querries
www.acodaq.com
[email protected]

Is this postion still open...

Similar Messages

Looking for a UK based Labview programmer, short term, contract or full time, depending on what suits. Immediate start, Signal Processing skills ideal.

We are a UK South-West based LabVIEW consultancy company looking for a LabVIEW programmer preferably with advanced signal analysis and processing skills, to become part of the team or work as a short term contractor. We will be looking to advance their skills through a range of different projects that we work on, from aerospace test and measurement, through to shop floor data collection and User Interface marketing.
Must have at least two years experience in LabVIEW and have an electronic engineering based degree or be able to show signal analysis is an area of expertise. We are looking to fill the position as soon as possible.
Please your CV’s to the below address.
[email protected]

If the candidate had all the correct attributes then it could indeed be an option.
Regards
Peter

Chicago Based Labview Electrical Engineer Available for Remote Work

I work while you sleep
I have over 8 years experience in Labview including most recently; GPS route mapping, CDMA and GSM test systems, OFDM and FSK test systems, and standalone applications (details available upon request).
I'm looking for remote projects to work on in the evening to supplement my income and pay for all the expensive Christmas gifts. I am willing to do work at reasonable rates based on project goals. I have my MS in Electrical Engineering and over 8 years of digital hardware design experience as well as automation experience with Labview. I have pretty much automated every piece of test equipment that has crossed my path.
Full source code, documentation, flow diagram, etc. upon project completion! Labview 8.5, Windows XP
Regards,
Labview 4 You
Electrical Engineer, Labview Guru

This is a repost to show this thread is still active.
I have over 8 years experience in Labview including most recently; GPS route mapping, CDMA and GSM test systems, OFDM and FSK test systems, and standalone applications (details available upon request).
I'm looking for remote projects to work on in the evening to supplement my income. I am willing to do work at reasonable rates based on project goals. I have my MS in Electrical Engineering and over 8 years of digital hardware design experience as well as automation experience with Labview. I have automated almost every piece of test equipment that has crossed my path.
Full source code, documentation, flow diagram, etc. upon project completion! Labview 8.5, Windows XP
Regards,
Labview 4 You
Electrical Engineer, Labview Guru

Need Labview Contractor

Maintain/Enhance Labview software that is used to control instruments
(example: Optical Power Meters, Laser Power Meters) in Laser prototype
build line. Must be able to extract requirements from Scientists and
quickly implement a solution. Develop Labview application to write
appropriate data to an existing Access database. Helpful if can also
help develop C++ Access database reporting/data mining applications.
3+ month contract position, on site at InPhase Technologies (Longmont, Inphase-tech.com). Minimum of 20 hours/week, prefer 40 hours/week.
Please send resume/work history to [email protected]

This position is budgeted for 3+ months as a contractor. On the other hand, InPhase is a growing startup company, and the workload is expected to increase over time. Hence, there is a good chance this position could go permanent ... or be extended for a longer period of time.
John

GCC based LabVIEW experienced professional

Worked in the USA with Freescale Semiconductors for 10 years and have intensely used LabVIEW for various purposes.
Recently moved to the Gulf Cooperation Council to look for career opportunities here.
Open to all forms of discussion for opportunities. Please feel free to write on [email protected]

I am located in the Illinois in the Chicago Area. You can view my WEB page at www.completeAutomatedSolutions.com or email me at [email protected] if you have any questions. I have extensive automation experience, LabVIEW Certified, Vision Expert, strong hardware knowledge, RF Testing, and use Test Stand to develop applications.
I am currently looking for contract work or subcontracting portions of a larger system. Send me an email to get started developing a cost effective solution for your industry.
Complete Automated Solutions
Providing Cost Effective Solutions for Industry
Matthew Fitzsimons
Certified LabVIEW Architect
LabVIEW 6.1 ... 2013, LVOOP, GOOP, TestStand, DAQ, and Vison

LabVIEW consultant required in Ballarat, Australia

I have an automotive test machine running a LabVIEW interface, controlled by a NI acquisition card.
It would be polite to describe the machine as "legacy". The entire machine is dinosaur era. The NI / LabVIEW upgrade was done in-house by somebody long since departed. The hardware belongs in a museum and the control PC has been running on borrowed time for at least a decade.
I need an experienced LabVIEW consultant to bring the machine back up to date; replace hardware with current supported models, and update software to suit.
Any local (ie Melbourne) LabVIEW contractors should drop me a line at [email protected], or call me on 03 5327 0318 to discuss.
Thanks,
Tim

Dear Sir,
I am working as application engineer and completed my M.Tech. Project (for GM and ISRO) from IIT Kanpur in Smart Systems Lab, Mechanical Engineering Dept. IIT Kanpur. I have 1.5 year of job Experience as junior R&D engineer. I have profound experience in developing microcontroller and LabView based system and my research work reflects it.
DAQ and software interfaced while doing projects:
LabVIEW- 7.1- 8.0
Interface of various sensor like RTD, PVDF, Bi-morph, Theromcouples, LVDT, Strain gauge and Optical Encoders through DAQ.
Motion Control : Servo and Stepper.
DSP- Speedy 33 and DSp module
Basic of DSC and Image IMAQ.
You can mail me for further details at [email protected] May I can justify your requirements.
Waiting in anticipation.
Thanking you,
Yours Truly,
Om Prakash Patel.
Message Edited by ni_op on 09-18-2006 08:58 AM

Using Fieldpoint from Labview RT on a PXI System

I have a PXI system with Labview RT (PXI 8186 controller with LVRT ver 7.1).
I wanted to connect a FP remote I/O system to this controller. The Fieldpoint system I have has a FP-1000 RS-232 Network module.
I was hoping to be able to connect the FP-1000 to the serial port of the PXI-8186, and use the standard Fieldpoint VIs to write/read data (as you would from a Windows-based Labview app).
It doesn't seem to be that easy, trying to download any code with a Fieldpoint VI down to my RT target gives an error ("failed to load shared library FPLVMgr.dll on RT target device"). Looking through MAX I see that Fieldpoint drivers are not loaded on the RT target, and there is no option to load them there either.
So: Ho
w do I control my Fieldpoint units from my PXI System using Labview RT?
Any help would be much appreciated.
Thanks,
Ravid

Hi, Ravid.
Effectively, under LabVIEW RT, you cannot use the standard FieldPoint VIs to communicate to a FieldPoint module, since they are not supported. If you have a serial module, like the FP-1000 or FP-1001, you need to use Optomux commands to interface and communicate to it. You can find great examples on how to do the communication in the Example Finder of LabVIEW >> Hardware Input and Output >> FieldPoint >> Optomux >> and use any of the examples that use VISA to communicate to the modules. To run the examples, first target LabVIEW to your 8186 and open the example. Before running it, match the baud rate and address specified in your FP-1000 with the controls in the Front Panel. Also, verify that you have either an alias defined for COM1, or use AS
RL::INSTR1 for the VISA resource name. You will need to have VISA RT installed on your RT Target to be able to run this examples.
You can find the Optomux commands in LabVIEW under the Advanced FieldPoint palette. For more information on Optomux commands, you can take a look at the FP-1000/1001 Programmer Reference Manual
Let me know if you have further questions. I hope this helps!
Gustavo Valdes
Applications Engineer

What are resources that one has to use motion control in LabView?

I am a newbie at Labview and I am trying to get a stepper motor to drive a shaft for one rotation (the shaft is attached to a bearing which will rotate a laser around a fixed object in the center). I am very limited in experience and I am wondering if ValueMotion is the way to go. Do you have to purchase the PC controller from NI to use value or flex motion? It would appear that using the intialization and setup VI's that ship with LV 6i would be the easiest and quickest route.
What demos/programs for labview will be best in helping me in my efforts? I have yet to even select the controller or stepper motor for this application.

Hello Graymalkin79...
LabVIEW and an NI motion controller for your PC are an excellent combination for the application that you describe. To answer your specific questions...Yes the ValueMotion and FlexMotion VI's require a PC based controller from NI. For your application, either the 7334 stepper controller (ValueMotion) or the 7344 step/servo controller (FlexMotion) will do the trick. For straighforward stepper control as you describe in your application, ValueMotion is fine and the VI's for init, setup and operation should have you up and running quickly. FlexMotion provides a significant level of motion capability and overall system integration that may enhance your total application, but that's difficult to determine from your brief description.
Most
any Stepper Motor requires a power driver unit like the MID7602, and the selection of this component really depends on the motor that you choose and its associated torque and speed requirements in your system.
Both ValueMotion and FlexMotion VI libraries provide motion demos that you can use interactively as well as VI's that you can integrate into your overall laser based LabVIEW application.

LabVIEW on the Mac at Macworld Expo 2008

National Instruments had a very small booth at Macworld Expo this year. They were there nonetheless and I asked them a few questions about the current state of LabVIEW on the Mac.
I also wanted to find out how, and if, a current Windows user like
myself could use a Mac exclusively and still manage to satisfy Windows
based LabVIEW project clients. According to Mike Neil, LabVIEW product
manager, you can have your cake, er… Mac and eat it too. With the use
of virtual machines (vmware fusion, parallels) or bootcamp
(which boots the whole machine into Windows), you can now run your
windows development environment on a Mac and satisfy any Windows
project requirements. Which leaves me asking myself, why am I still on
a PC?
Watch the video:
http://vishots.com/2008/01/24/labview-on-the-mac-is-alive-and-well-macworld-expo-2008/
Michael Aivaliotis
VI Shots LLC

Hey Michael,
With Parallels, VMWare, and Boot Camp, there are certainly fewer excuses to not own a Mac!
Take a look at this article as well:
Developing Data Acquisition Systems on the Mac with Virtualization Technology
It dicusses some of the testing done here with Parallels and VMWare.
Regards,
Kevin H
National Instruments
WSN/Wireless DAQ Product Support Engineer

Looking for a Houston area contractor.

All,
EM is looking for a local LabVIEW contractor to help us with additional projects. CLD or CLAD preferrered. Oilfeld experience, RT and FPGA is a plus.
Contact:
Kenneth Miller
Erdos Miller
713-562-4315
[email protected]
Local applicants only please.

I am interested in this position. I am CLD
Attachments:
YOUNG Charles122911 Resume.doc ‏60 KB

UK LabView user group?

Is there any active UK-based LabView user group that has regular
meetings anywhere? There are a few around the rest of the world, but I
can't see anything in the UK. I think it would be a good idea to get
one together, if one does not exist here.
Feedback welcome - please reply to newsgroup as email is disabled to
prevent spam.
Thanks,
Matt

HI Matt,
Try posting to info-LabVIEW
This is the weekly admin reminder for readers of the Info-LabVIEW mailing list and mail digest. (19oct01)
o Administrative issues such as SUBSCRIPTION and DELETION REQUESTS
MUST be addressed to the admin address, which is
o To post to the list, mail to . DO NOT
send subscription and deletion requests to .
o This is a user list, run by and for LabVIEW users. If you have a
commercially available item to announce, please make the announcement
brief.
o It is not, ever, acceptable to post "virus warnings" to this list. For
any reason.
A set of Frequently Asked Question
s (FAQs) for LabVIEW are available from our web server at .
Tom Coradeschi, Info-LabVIEW List Maintainer
http://www.info-labview.org/
>
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

UK Based CLA/CLED/CPI freelancer actively seeking new challenge

Hi,
I am a UK based LabVIEW architect (also qualified as CLED and CPI) and am on the lookout for LabVIEW/systems engineering type work. My formal education consists of bachelors and masters in Electronic Engineering.
My professional experience includes significant exposure to virtually the entire LabVIEW stack (PC/RT/FPGA) and I have done work in a diverse range of industries including Formula 1, Telecommunications and Aerospace.
If you are in need of a skilled LabVIEW architect, for any size project, please do not hesitate to contact me via this forum.
My CV is available on request.
nrp
CLA

LabVIEW CLD with 8 years experience in Austin, TX

Hi,
I am a Certified LabVIEW Developer with around 8 years of labVIEW experience which involves working with most of the standard industry protocols. I have worked in both lab and production environments.
I have worked using DAQ, GPIB, PXI, VXI, Fieldpoint, CDAQ, VISION, Motion, Sound and Vibration, Mobile ....Please contact me for additional details.
Regards,
Jagan
[email protected]
256-520-7981

Hi,
We are looking for at least 6-month LabVIEW contractor in San Jose, CA. Please refer to the following link if you are interested:
http://sfbay.craigslist.org/sby/sof/243379434.html
Thanks,
Mark

Labview 3.1 from Mac to PC

Hi,
who is experienced in switching Labview 3.1 applications from MacIntosh to PC
WIN 9.x/NT based LabView 5.0?
Who knows all about the different filetypes (type & creator used by Mac) and
the right translation for PC fileformat (filename in 8.3 convention, means
"filename.ext")
Thanks for any help, Rolf

Hey Ron,
LabVIEW is a platform independent environment, so you should have no problems
porting your MAC VI's to Windows. However, I found a Knowledge Base article that
may help you. I went to NI's homepage (www.ni.com) and typed "transfer between
platforms" and only searched the support pages. The first hit should
help you.
I hope this helps,
Kevin
Rolf Lindenau wrote:
> Hi,
>
> who is experienced in switching Labview 3.1 applications from MacIntosh to PC
> WIN 9.x/NT based LabView 5.0?
>
> Who knows all about the different filetypes (type & creator used by Mac) and
> the right translation for PC fileformat (filename in 8.3 convention, means
> "filename.ext")
>
> Thanks for any help, Rolf

MATLAB from LabVIEW on Sun work station

Is it possible to access MATLAB script from LabVIEW on a Sun work station. If so how - for there is no MATLAB script node in SUN based LabVIEW
-Sheela

Because LabVIEW uses ActiveX technology to implement MATLAB script nodes, they are available only on the Windows platform.
There may be other ways to invoke the Matlab script server in Unix but I am not aware of any.
Chris_Mitchell
Product Development Engineer
Certified LabVIEW Architect

UK-based LabVIEW Contractor

Similar Messages

Maybe you are looking for