Ultra 10 and Creator 3D Configuration Help
Hi.
First post. Like so many others, I wanted to try Sun systems, so I got an Ultra 10 off eBay. I didn't have a 13W3 connector or monitor, so I pulled the Creator 3D card, and installed Solaris 9, using the built-in ATI video. Now that my 13W3 to HD15 adaptor has come in, I'm trying to get the 3D card back into the system, and I'm having trouble configuring it.
It took me a while to find out that FFBCONFIG is not in Solaris 9, (at least it doesn't show up in a "find file" search of local storage) and then a short time to learn about M64CONFIG. I ran the M64CONFIG from a terminal window in the CDE, and it seemed to take, but I still get the "Can't find driver for console framebuffer" error upon reboots after re-installing the 3D card. The system halts while trying to load X. Everything up to that point (with the exception of the above alert) seems correct, so I know it's just the card and the configuration. I know the card works, because on bootup, the Sun logo is different with the card in, as opposed to the ATI Sun logo, and, of course, I DO have video...
I used the M640 file with M64CONFIG and the -defaults option while configuring with the ATI card as my video source, because that's the only file in the directory, then re-installed the 3D. Did I miss a step somewhere?
Oh- I'm still a real Solaris newbie, so if you could answer in plain English, rather than a lot of UNIXSpeak it prevents my lips from moving while I'm reading and thus, not look like an idiot! :-)
If I didn't supply enough information here, just let me know and I'll add whatever's needed. Thanks.
Aside from this issue, so far it's been a blast!
..Joe
just re-install the OS
Where's the fun in that? :)
Actually, that's my last resort. The reason I'm trying to avoid it is because this way, I get to learn how to do it the hardware way.
Perhaps you would be kind enough to anser one question on re-installing the OS: Were I to do that, will it overwrite all the files I have changed, and do a completely clean, new install? I had a devil of a time getting the workstation configured for internet access. I would have the ability to see the web, but only by IP addressing. DNS wasn't working, and a friend who's a Sun engineer changed one NIS file and got it working fine. Would that get overwritten? Also, I have downloaded several programs (Open Office, FireFox, etc.): Would those remain after a new OS install?
Thanks for all the help.
..Joe
Similar Messages
-
Cluster,FileServlet and images - need configuration help
Hi All.
We're using 2 wl5.1sp9 as "proxies" and 2 wlcs3.2 as the application server.
We'd set the default servlet to be the cluster servlet
(weblogic.httpd.defaultServlet=cluster
weblogic.httpd.register.cluster=\
weblogic.servlet.internal.HttpClusterServlet
weblogic.httpd.initArgs.cluster=\
defaultServers=10.5.195.31:80:443|10.5.195.30:80:443,\
DebugConfigInfo=ON)
where these IP's are the application servers internal IPs.
Now, we wanted to serve the static files (images, html, js) from the wl
servers.
For our surprise, just putting the files on the wl servers was NOT doing the
job!
(We believed that the cluster first searches locally and only after that
looks on other hosts)
So we registered the images by file type
(weblogic.httpd.register.*.gif=weblogic.servlet.FileServlet
weblogic.httpd.register.*.jpg=weblogic.servlet.FileServlet)
Now, if we got images that are on the application servers, we can't get
these files!
Could someone please help how to set this configuration correctly?Hi.
Please try posting this on weblogic.developer.interest.servlet or
weblogic.developer.interest.clustering.
Thanks,
Michael
"R@nsh!" wrote:
Hi All.
We're using 2 wl5.1sp9 as "proxies" and 2 wlcs3.2 as the application server.
We'd set the default servlet to be the cluster servlet
(weblogic.httpd.defaultServlet=cluster
weblogic.httpd.register.cluster=\
weblogic.servlet.internal.HttpClusterServlet
weblogic.httpd.initArgs.cluster=\
defaultServers=10.5.195.31:80:443|10.5.195.30:80:443,\
DebugConfigInfo=ON)
where these IP's are the application servers internal IPs.
Now, we wanted to serve the static files (images, html, js) from the wl
servers.
For our surprise, just putting the files on the wl servers was NOT doing the
job!
(We believed that the cluster first searches locally and only after that
looks on other hosts)
So we registered the images by file type
(weblogic.httpd.register.*.gif=weblogic.servlet.FileServlet
weblogic.httpd.register.*.jpg=weblogic.servlet.FileServlet)
Now, if we got images that are on the application servers, we can't get
these files!
Could someone please help how to set this configuration correctly?--
Developer Relations Engineer
BEA Support -
I was updating to OS5 and instead my iPhone went back to factory settings. Now the iPhone doesnt read my sim card and cannot be configured. Please help
Nothing happened, i managed to get my computer to recognise it and now restoring... but it says 3 hours remaining?! Will i lose everything?
-
KT4 Ultra and FastTrak 376 issues.
I recently purchased a KT4 Ultra and installed it on me computer. Everythings fine, it boots and the bios recognises my IDE devices. It won't allow me to enter the bios though and it just sits there with the screen displaying this.
FastTrak 376 (tm) BIOS Version 1.00.0.18
(copyright info)
Scanning IDE drives
any help would be greatly appreciated
thx alot )NEVER HAPPENED TO ME. TRY DISCONNECTING ALL IDE DEVICES, CLEAR THE CMOS AND PRESS DEL BEFORE THE PROMISE BIOS LOADS.
MAYBE YOU'LL GET INSIDE TO DEACTIVATE IT FROM LOADING AT INTEGRATED PERIPHERALS - ONBOARD PCI CONTROLLER - SEARIAL ATA CONTROLLER.
DO YOU HAVE AN SATA HDD? YOU COULD USE ONE FOR TRYING TO SETUP AN ARRAY IN THE PROMISE BIOS (BY PRESSING CTRL+F AND THEN CHOOSE THE AUTO CONFIGURATION). AFTER THAT MAYBE YOU CAN ENTER THE BIOS.
YOU CAN ALSO TRY TO FIND AN MODDED BIOS FOR THE KT4-ULTRA THAT DOES NOT LOAD THE PROMISE SATA BIOS BY DEFAULT. -
Troubleshooting Enterprise Beas, Netbeans 5.0 and Creator 2
Hi Gurus. I am using Netbeans 5.0 to develop Enterprise Beans and Creator 2 to consume the beans, as a database I use Oracle 10g xe and Sun Application Server 8.2 as a App. Server (Not the one embedded in creator). I successfully created an enterprise bean with methods that create and get data in Netbeans 5.0 and also I am able to test them with a servlet without troubles. I consume the enterprise bean in creator, then I use it in a web page, after that I deployed into a remote server (8.2) all the application, but when I try to insert or get the data I get this Exception:
com.sun.rave.web.ui.appbase.ApplicationException: #{Ventas$Clientes.buttonNuevo_action}: javax.faces.el.EvaluationException: java.lang.RuntimeException: RemoteException occurred in server thread; nested exception is:
java.rmi.RemoteException
com.sun.rave.web.ui.appbase.faces.ViewHandlerImpl.destroy(ViewHandlerImpl.java:601)
com.sun.rave.web.ui.appbase.faces.ViewHandlerImpl.renderView(ViewHandlerImpl.java:302)
com.sun.faces.lifecycle.RenderResponsePhase.execute(RenderResponsePhase.java:87)
com.sun.faces.lifecycle.LifecycleImpl.phase(LifecycleImpl.java:221)
com.sun.faces.lifecycle.LifecycleImpl.render(LifecycleImpl.java:117)
javax.faces.webapp.FacesServlet.service(FacesServlet.java:198)
sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
java.lang.reflect.Method.invoke(Method.java:585)
org.apache.catalina.security.SecurityUtil$1.run(SecurityUtil.java:249)
java.security.AccessController.doPrivileged(Native Method)
javax.security.auth.Subject.doAsPrivileged(Subject.java:517)
org.apache.catalina.security.SecurityUtil.execute(SecurityUtil.java:282)
org.apache.catalina.security.SecurityUtil.doAsPrivilege(SecurityUtil.java:165)
java.security.AccessController.doPrivileged(Native Method)
com.sun.rave.web.ui.util.UploadFilter.doFilter(UploadFilter.java:194)
Am I doing something wrong in creator? did I miss a step configuring the bean? I followed the instructions in all the tutorials available to add and use Enterprise Beans. if I am able to use a enterprise bean in Netbeans 5.0 to insert and obtain data, Why I am not able to use it in Creator? I believe that I am so close to get the things working but that last step is killing me. I will appreciate any help. Thanks. (Sorry about grammar!!!!)Thanks for your help man. That was a very good advice. I rebuild everything in the application server bundled in creator, debugged and the the real problem appeared. I didn't take care about the size of data that I was willing to store in the jsp page. I was using toString() method to get the data from the text fields and after debugging I figured out is needed getText().toString() to get data form the fields, everything was out bout bounds. Now the application works fine. You save my life!!! How do I assign you the Duke dollars?
Message was edited by:
Patricio -
X201 vs X201s and external monitor, please help
Hello
I am about to order my first thinkpad and have 2 questions and would greatly appreciate your thoughts
I need a machine that is fast enough to handle huge data files quickly.
1. Not sure whether to go for:
X201 with i7-620M processor 2.66GHz, 8Gb RAM and 128Gb SSD
or the slower but lighter
X201s with i7-640LM processor 2.13GHz again with 8Gb RAM and 128Gb SSD
2. When working at home and work i hope to connect to a ~24" monitor (1920 x 1080)
I have been informed by lenovo sales people today
"the x201 will only support a maximum resolutionof 1280 x 800"
Is this the case, how will it effect my use of a large external monitor?
I do note that the x201s seems to support 1440 x 900 and would be happy to buy an ultra base for work and home if that helps?
Look forward to hearing from you
cheers
DanI had the same concerns when trying to decide between the two models.
In the end I went with the X201 -with the i7-620M proc.
My reasoning is that, sure the performance difference between the two processors may not be that big, but I'm future-proofing the machine just a little bit more at only a marginal additional cost.
As for battery-life - my laptop spends most of the day plugged in, so the benefits of the lower voltage processor and lower power consumption wouldn't be that great.
I bike in to work every day with the laptop on my back, so weight and size were important issues for me. The laptops are the same size. With the 6 cell battery they're both 1.1" thick. Only if you slap on the 4cell does the x201s become thinner. The x201 does weigh about a quarter pound more when configured with the 6 cell. (3.1 lbs as opposed to 2.8 or so) I was willing to make that tradeoff for better performance.
As for the video output - I haven't plugged the x201 into my home monitor: 24" , but its performing beautifully on my 20" office monitor @ 1680x1050. -
Active Directory replication and login errors (Plz HELP !!)
Hi All,
We have one forest domain (XXXX.LOCAL)and lots of child domains (XXX.XXXX.LOCAL).
We are facing issue that child domains are not able to login with forest administrator account and there are also lots of replication errors.
Exchange OWA gives error of not able to find particular XXX.XXX.local child domain.
dcdiag from child domain is :
C:\Windows\system32>
C:\Windows\system32>nltest.exe /dsregdns
Flags: 0
Connection Status = 1311 0x51f ERROR_NO_LOGON_SERVERS
The command completed successfully
C:\Windows\system32>nltest.exe /dsregdns
Flags: 0
Connection Status = 1311 0x51f ERROR_NO_LOGON_SERVERS
The command completed successfully
C:\Windows\system32>
C:\Windows\system32>dcdiag
Directory Server Diagnosis
Performing initial setup:
Trying to find home server...
Home Server = PMA-DC01
* Identified AD Forest.
Done gathering initial info.
Doing initial required tests
Testing server: HEC-CITY\PMA-DC01
Starting test: Connectivity
......................... PMA-DC01 passed test Connectivity
Doing primary tests
Testing server: HEC-CITY\PMA-DC01
Starting test: Advertising
Warning: PMA-DC01 is not advertising as a time server.
......................... PMA-DC01 failed test Advertising
Starting test: FrsEvent
......................... PMA-DC01 passed test FrsEvent
Starting test: DFSREvent
There are warning or error events within the last 24 hours after the
SYSVOL has been shared. Failing SYSVOL replication problems may cause
Group Policy problems.
......................... PMA-DC01 failed test DFSREvent
Starting test: SysVolCheck
......................... PMA-DC01 passed test SysVolCheck
Starting test: KccEvent
......................... PMA-DC01 passed test KccEvent
Starting test: KnowsOfRoleHolders
[PMA-DC02] DsBindWithSpnEx() failed with error -2146893022,
The target principal name is incorrect..
Warning: PMA-DC02 is the PDC Owner, but is not responding to DS RPC
Bind.
[PMA-DC02] LDAP bind failed with error 8341,
A directory service error has occurred..
Warning: PMA-DC02 is the PDC Owner, but is not responding to LDAP
Bind.
Warning: PMA-DC02 is the Rid Owner, but is not responding to DS RPC
Bind.
Warning: PMA-DC02 is the Rid Owner, but is not responding to LDAP
Bind.
Warning: PMA-DC02 is the Infrastructure Update Owner, but is not
responding to DS RPC Bind.
Warning: PMA-DC02 is the Infrastructure Update Owner, but is not
responding to LDAP Bind.
......................... PMA-DC01 failed test KnowsOfRoleHolders
Starting test: MachineAccount
......................... PMA-DC01 passed test MachineAccount
Starting test: NCSecDesc
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
Fatal Error: Cannot retrieve SID
......................... PMA-DC01 failed test NCSecDesc
Starting test: NetLogons
......................... PMA-DC01 passed test NetLogons
Starting test: ObjectsReplicated
......................... PMA-DC01 passed test ObjectsReplicated
Starting test: Replications
[Replications Check,Replications Check] Inbound replication is
disabled.
To correct, run "repadmin /options PMA-DC01 -DISABLE_INBOUND_REPL"
[Replications Check,PMA-DC01] Outbound replication is disabled.
To correct, run "repadmin /options PMA-DC01 -DISABLE_OUTBOUND_REPL"
......................... PMA-DC01 failed test Replications
Starting test: RidManager
......................... PMA-DC01 failed test RidManager
Starting test: Services
w32time Service is stopped on [PMA-DC01]
......................... PMA-DC01 failed test Services
Starting test: SystemLog
A warning event occurred. EventID: 0x00000010
Time Generated: 04/21/2014 19:16:04
Event String:
Unable to Connect: Windows is unable to connect to the automatic upd
ates service and therefore cannot download and install updates according to the
set schedule. Windows will continue to try to establish a connection.
An error event occurred. EventID: 0x0000168E
Time Generated: 04/21/2014 19:44:42
Event String:
The dynamic registration of the DNS record '_kerberos._tcp.dc._msdcs
.PMA.XXXX.LOCAL. 600 IN SRV 0 100 88 PMA-DC01.PMA.XXXX.LOCAL.' failed on the fol
lowing DNS server:
An error event occurred. EventID: 0x0000168E
Time Generated: 04/21/2014 19:44:43
Event String:
The dynamic registration of the DNS record '_kerberos._tcp.PMA.XXXX.
LOCAL. 600 IN SRV 0 100 88 PMA-DC01.PMA.XXXX.LOCAL.' failed on the following DNS
server:
An error event occurred. EventID: 0x0000168E
Time Generated: 04/21/2014 19:44:43
Event String:
The dynamic registration of the DNS record '_kerberos._tcp.HEC-LAHOR
E._sites.PMA.XXXX.LOCAL. 600 IN SRV 0 100 88 PMA-DC01.PMA.XXXX.LOCAL.' failed on
the following DNS server:
An error event occurred. EventID: 0x0000168E
Time Generated: 04/21/2014 19:44:43
Event String:
The dynamic registration of the DNS record '_kerberos._udp.PMA.XXXX.
LOCAL. 600 IN SRV 0 100 88 PMA-DC01.PMA.XXXX.LOCAL.' failed on the following DNS
server:
An error event occurred. EventID: 0x0000168E
Time Generated: 04/21/2014 19:44:43
Event String:
The dynamic registration of the DNS record '_kpasswd._tcp.PMA.XXXX.L
OCAL. 600 IN SRV 0 100 464 PMA-DC01.PMA.XXXX.LOCAL.' failed on the following DNS
server:
An error event occurred. EventID: 0x0000168E
Time Generated: 04/21/2014 19:44:43
Event String:
The dynamic registration of the DNS record '_kpasswd._udp.PMA.XXXX.L
OCAL. 600 IN SRV 0 100 464 PMA-DC01.PMA.XXXX.LOCAL.' failed on the following DNS
server:
An error event occurred. EventID: 0x0000168E
Time Generated: 04/21/2014 19:44:43
Event String:
The dynamic registration of the DNS record '_kerberos._tcp.HEC-LAHOR
E._sites.dc._msdcs.PMA.XXXX.LOCAL. 600 IN SRV 0 100 88 PMA-DC01.PMA.XXXX.LOCAL.'
failed on the following DNS server:
An error event occurred. EventID: 0x00000C8A
Time Generated: 04/21/2014 19:44:51
Event String:
This computer could not authenticate with \\LHR-DC01.XXXX.LOCAL, a W
indows domain controller for domain XXXX, and therefore this computer might deny
logon requests. This inability to authenticate might be caused by another compu
ter on the same network using the same name or the password for this computer ac
count is not recognized. If this message appears again, contact your system admi
nistrator.
An error event occurred. EventID: 0xC00A0038
Time Generated: 04/21/2014 19:46:02
Event String:
The Terminal Server security layer detected an error in the protocol
stream and has disconnected the client. Client IP: 10.87.193.37.
An error event occurred. EventID: 0x40000004
Time Generated: 04/21/2014 19:52:41
Event String:
The Kerberos client received a KRB_AP_ERR_MODIFIED error from the se
rver pma-dc02$. The target name used was PMA\PMA-DC02$. This indicates that the
target server failed to decrypt the ticket provided by the client. This can occu
r when the target server principal name (SPN) is registered on an account other
than the account the target service is using. Please ensure that the target SPN
is registered on, and only registered on, the account used by the server. This e
rror can also happen when the target service is using a different password for t
he target service account than what the Kerberos Key Distribution Center (KDC) h
as for the target service account. Please ensure that the service on the server
and the KDC are both updated to use the current password. If the server name is
not fully qualified, and the target domain (PMA.XXXX.LOCAL) is different from th
e client domain (PMA.XXXX.LOCAL), check if there are identically named server ac
counts in these two domains, or use the fully-qualified name to identify the ser
ver.
A warning event occurred. EventID: 0x8000001C
Time Generated: 04/21/2014 19:53:42
Event String:
When generating a cross realm referal from domain XXXX.LOCAL the KDC
was not able to find the suitable key to verify the ticket. The ticket key vers
ion in the request was 25 and the available key version was 22. This most common
reason for this error is a delay in replicating the keys. In order to remove th
is problem try forcing replication or wait for the replication of keys to occur.
An error event occurred. EventID: 0x40000004
Time Generated: 04/21/2014 20:13:25
Event String:
The Kerberos client received a KRB_AP_ERR_MODIFIED error from the se
rver pma-dc02$. The target name used was LDAP/4a166db9-c39c-4069-99e7-8a233ce2c0
be._msdcs.XXXX.LOCAL. This indicates that the target server failed to decrypt th
e ticket provided by the client. This can occur when the target server principal
name (SPN) is registered on an account other than the account the target servic
e is using. Please ensure that the target SPN is registered on, and only registe
red on, the account used by the server. This error can also happen when the targ
et service is using a different password for the target service account than wha
t the Kerberos Key Distribution Center (KDC) has for the target service account.
Please ensure that the service on the server and the KDC are both updated to us
e the current password. If the server name is not fully qualified, and the targe
t domain (PMA.XXXX.LOCAL) is different from the client domain (PMA.XXXX.LOCAL),
check if there are identically named server accounts in these two domains, or us
e the fully-qualified name to identify the server.
An error event occurred. EventID: 0x40000004
Time Generated: 04/21/2014 20:13:25
Event String:
The Kerberos client received a KRB_AP_ERR_MODIFIED error from the se
rver pma-dc02$. The target name used was ldap/pma-dc02.pma.XXXX.LOCAL. This indi
cates that the target server failed to decrypt the ticket provided by the client
. This can occur when the target server principal name (SPN) is registered on an
account other than the account the target service is using. Please ensure that
the target SPN is registered on, and only registered on, the account used by the
server. This error can also happen when the target service is using a different
password for the target service account than what the Kerberos Key Distribution
Center (KDC) has for the target service account. Please ensure that the service
on the server and the KDC are both updated to use the current password. If the
server name is not fully qualified, and the target domain (PMA.XXXX.LOCAL) is di
fferent from the client domain (PMA.XXXX.LOCAL), check if there are identically
named server accounts in these two domains, or use the fully-qualified name to i
dentify the server.
......................... PMA-DC01 failed test SystemLog
Starting test: VerifyReferences
......................... PMA-DC01 passed test VerifyReferences
Running partition tests on : DomainDnsZones
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... DomainDnsZones passed test
CrossRefValidation
Running partition tests on : PMA
Starting test: CheckSDRefDom
......................... PMA passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... PMA passed test CrossRefValidation
Running partition tests on : ForestDnsZones
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... ForestDnsZones passed test
CrossRefValidation
Running partition tests on : Schema
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Running partition tests on : Configuration
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Running enterprise tests on : XXXX.LOCAL
Starting test: LocatorCheck
......................... XXXX.LOCAL passed test LocatorCheck
Starting test: Intersite
......................... XXXX.LOCAL passed test Intersite
C:\Windows\system32>There are a number of things that can cause this, such as:
DNS is misconfigured to support a parent-child-additional tree forest.
Incorrect DNS zone replication scope for the design, which points back to the point #1.
AD Sites are misconfigured for the physical environment. For example if you have a hub and spoke physical environment, you can't use the default settings that bridge all sites (BASL) and must individually configure them.
Incorrect DNS settings on the DCs.
Multi-homed DCs.
Time service is not configured properly and/or syncing from the VM host, which should be configured otherwise (Microsoft, VMware and Citrix have KBs explaining this).
Default security settings at either the parent, child or both domains, have been altered.
Firewalls between DCs, such as perimeter firewalls, or installed antivirus protection features if not excluded on DCs properly, will cause this, too.
That's the short list. If you can describe some of the points above, it may help us pinpoint where the issue may be.
Some links that may help understand some of the bullet points:
AD Site Design, DNS & the DC Locator Process, and Auto Site Link Bridging, or Bridge All Site Links (BASL)
http://blogs.msmvps.com/acefekay/2013/02/24/ad-site-design-and-auto-site-link-bridging-or-bridge-all-site-links-basl/
DNS Design Options in a Multi-Domain Forest - How to create a Parent-Child DNS Delegation, and How to Configure DNS to create a new Tree in the Forest
Published by Ace Fekay, MCT, MVP DS on Oct 1, 2010 at 12:22 PM
http://msmvps.com/blogs/acefekay/archive/2010/10/01/dns-parent-child-dns-delegation-how-to-create-a-dns-delegation.aspx
Configuring the Windows Time Service for Windows 2000, 2003, 2008 and newer, explanation of the time service hierarchy, and more
Published by Ace Fekay, MCT, MVP DS on Sep 18, 2009 at 8:14 PM 3050 1
http://msmvps.com/blogs/acefekay/archive/2009/09/18/configuring-the-windows-time-service-for-windows-server.aspx
Ace Fekay
MVP, MCT, MCSE 2012, MCITP EA & MCTS Windows 2008/R2, Exchange 2013, 2010 EA & 2007, MCSE & MCSA 2003/2000, MCSA Messaging 2003
Microsoft Certified Trainer
Microsoft MVP - Directory Services
Complete List of Technical Blogs: http://www.delawarecountycomputerconsulting.com/technicalblogs.php
This posting is provided AS-IS with no warranties or guarantees and confers no rights. -
SFTP adapter Configuration help:
Dear All,
I am trying to configure SFTP (seeburger) in sap PI.
I want to know how to connect SFTP adapter of seeburger with an SSH sever. (I have installed free SSH Server in my laptop).
How to connect using SFTP SETTING as
AUTHENTICAION Method: Private Key authorisation
how to generate/use private key.
Please Advice,
Prakash
Edited by: senthilprakash selvaraj on Jan 20, 2010 6:42 AMDear All,
I have installed SSH server and genreated the RSA key in Visual admin and i have configured the SFTP adater properly.
Now i have a different issue.
In Communication channel monitoring once i start the channel(SFTP) i am not getting any message. Its just saying Channel started and thats it. nothin else is coming. not even throwing any error. what should i do. why its happing like that.
I Tried with Authentication mode as Private Key as well as Password. in both configurations are proper.
also i tried refreshing the cache..no use.
Please help,
Senthilprakash -
How to enable workflow notification mailer and how can it help me?
Hello
I am on 12.0.6
I want to know how to enablke workflow notification mailer and how it can help me?
Do i need to seperately license it?
is there any patch that i have to apply in order to use it
Please advice and help me with my queryHi,
I want to know how to enablke workflow notification mailer and how it can help me?See the documents referenced in this thread.
Workflow Configuration and Troubleshoot
Workflow Configuration and Troubleshoot
Do i need to seperately license it?No.
is there any patch that i have to apply in order to use itSee the thread referenced above.
Regards,
Hussein -
What's the implicit joins and how to configure it?
Hello guys
what's the implicit joins and how to configure it? What's the purpose of implicit and explicit joins?
Please help
Thank youThus, on my side, I think that :
Explicit join define the join condition between the key column from the table.
(table1.di = table2.id)
While
Implicit Join define :
* the type of join outer, inner, ...
http://gerardnico.com/wiki/dw/join/start
* And the relationship (one-to-many, cardinality)
http://gerardnico.com/wiki/dw/data_quality/relationships
And all this information are used to generate the statement (query).
And I don't really know why you have two type of key :
* Physical Foreign Keys
* Logical Foreign Keys
Regards
Nico -
Getting problem while installing Snow Leopard (10.6.3) on my Mac Mini. The following issue is showing :
"mac os x snow leopard cannot be installed on this computer"
And My Mac Configuration details: Model Name: Mac Mini Model Identifier: Macmini2,1
Intel Core 2 Duo
1.83Ghz
l2Cache: 2mb
Memory : 2GB
Bus Speed: 667MHz
Please help me......
ThanksActually i have Mac OS X 10.5.4 DVD, I need to upgrade it to Snow Loepard(OS X 10.6)...
Please suggest me what to do???
Thanks -
857 Wireless configuration help
Can someone help me with a wireless setup of an 857. I have done this in the past but can't remember the details. Basically I want very simple setup with WPA-PSK. The SDM interface is very confusing and I could do with the basic CLI for this.
Thanksplease see this link for the 857 initial configuration:
http://www.cisco.com/en/US/products/hw/routers/ps380/products_installation_guide_chapter09186a0080471066.html
this is a step-by-step for SDM and CLI basic configuration. -
Export and Import of Configuration Data
Hi All,
I have created a number of custom properties, structures, groups, renderers, layout sets etc and would like to move them from Dev to Test system.
I have found the following in the help doco:
"Export and Import of Configuration Data"
http://help.sap.com/saphelp_nw04/helpdata/en/e1/029c414c79b25fe10000000a1550b0/content.htm
However I am unable to see its functionality in our portal systems (namely the Actions->Export and Actions->Import functions).
Our version of Portal is: 6.0.9.6.0
KM: 6.0.9.3.0 (NW04 SPS09 Patch3)
Therefore we should be able to see it? no?
Are there any special settings to see these buttons?
Cheers,
VicThanks for your replies.
OK, so in otherwords, it is not available in SP09 and only in SP12+.
So, to "transport" this information I will have to manually reapply thes settings in the Test system!
Message was edited by: Victor Yeoh -
How we create custom infotype and how to configure with its subtypes.
hai abap-hr gurus,
how to create custom infotype and how to configure with its subtypes. when i am creating infotypes i am not getting how to configure subtypes.
plz help me for this with an example code.
thanks..
kiran kumarHi Kiran,
Please fallow the below steps to create the custom infotype. If you have any quires let me know.
For Creation of Infotype first Go to Transaction PM01, Enter the custom Infotype number which you want to create, it should be a 4 digit number and have to start with 9xxx.
then select the `Employee Infotype' radio button
after that select the `PS Structure Infotype'
then click on Create A separate table maintenance window appears
then Create a PS structure with all the fields you want on the infotype
Save and Activate the PS structure
now Go back to the initial screen of PM01
Click on `All' push button. It takes a few moments
Click on `Technical Characteristics. Infotype list screen appears
Click on `Change'(pencil) button
Now select your Infotype and click on `Detail' (magnifying glass) button
Give `T591A' as subtype table & also Give `T591S' as subtype txt tab
Give your subtype field as subtype field & Save and come back to PM01 initial screen
Click on `Infotype Characteristics' Infotype list screen appears
Click on `Change' (pencil) button & on New Entries
and then Enter your Infotype number and short text Here we have to set different Infotype Characteristics as per the requirement. (Better open another session with some standard Infotype's infotype characteristics screen and use as the reference
to fill yours). Now save ur entries
Now the Infotype is created and ready to use.
If you want to change the layout of the Infotype as per your
requirement
In the PM01 initial screen Select `Screen' radio button and give
2000 as the screen name, then click on edit.
In the next screen.. Select `Layout Editor' and click `Change'.
Screen default layout appears here you can design/modify the
screen..change the attributes of the fields..etc.
Save and activate. (Don't forget to `Activate at every level)
Regards,
Ramakrishna kotha. -
Reg : Milestone / Periodic and RRB Billing Configuration.
Hi SAP Gurus
we are integrating SD-PS to get back revenues on the project automatically. We are using WBS element as a real object at the item level of the Sales Order. There are going to be three kinds of Billing types: Periodic, Milestone and RRB (T&M and Travel). So we probably need an Order type and Item categories for different billing types. Travel expenses needs to be part of the Sales Order. For RRB, DIP profile needs to be configured to capture no. of hours worked on the project and travel expenses.
Please let me know what are things needs to be configured for this process. and how to configure the Milestone/ Periodic and RRB billing type.
ThanksHi,
http://help.sap.com/saphelp_46c/helpdata/en/dd/56069b545a11d1a7020000e829fd11/frameset.htm
http://help.sap.com/saphelp_46c/helpdata/en/59/54fc37004d0a1ee10000009b38f8cf/frameset.htm
http://help.sap.com/saphelp_46c/helpdata/en/59/54fc37004d0a1ee10000009b38f8cf/frameset.htm
Kapil
Maybe you are looking for
-
Adobe Flash Player, version 10.1.102.64 is installed, but I cannot access FP dependent applications (such as those on Facebook.) I used the link you previously provided http://www.adobe.com/products/flashplayer/fp_distribution3.html to download th
-
Simultaneous Thumb drive or CD I/O charging projector with new MacBook?
How does one give a presentation with the new MacBook needing to connect to a projector, while reading data from a thumb drive or external disk/CD, while needing to charge the MacBook? Is there a multi - port type adapter to allow for all these conn
-
Visualizers For The iPod. (Not for iTunes)
We all know the many different visualizers for the iTunes, but are there any visualizers for the iPod itself? I've got the 5th Gen 30GB Video by the way. Can you tell me what site I can get them at, if such visualizers exists! Like how u download mp3
-
Oracle 9iR2 db and Hardware movement
Friends We are moving our servers (OS AIX 5.3) and installed softwares from harware IBM p670 to 570. We will move Oracle installations also. We plan to move disk images (no new Oracle server installation) and network controls. Is there any things tha
-
Lumia 925 Update 1 (Dev. Preview)
Tweets from accounts I follow appear in the Action Center not once, but five times each. Difficult to say, if it's the OS, Twitter app or the twitter.com servers to blame.