Unable to access HP printer to router

I have a Macintosh running 10.8. HP officejet 4500 G510g-m non wireless printer. Belkin N600 wireless router with USB port and 4 ethernet ports
When I plug the printer in via the USB port, Belkin software sees the printer but is unable to connect. I have firewall turned off. I can connect a USB external HD to the router and it sees it.
I've contacted Belkin and was told the issue is with the printer.
I have mulitple PCs, iPhone, iPad and would like to make the printer available to all via the router.
I am not sure what to try next or should I just buy a wireless printer?
Thank you.

Why don't you plug the printer into the router with an Ethernet cable?
You still may have problems as Belkin does not support (or support properly) Bonjour - the discovery protocol that allows your Mac to find your printer.
You may be better off buying a better router like Linksys, Netgear or Apple Airport.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Similar Messages

Unable to Access Router Admin Page

So I have a weird situation where my router is working fine to allow me access to the internet, yet I am unable to access the router administration page, 192.168.1.1 This occurred after the router froze up tuesday. I reset the router to factory defaults and have since been able to get online, but not access admin page. Router is a Linksys WRT-54GS V 7
Modem is motorolla SB1505
ISP is earthlink, but in NYC so its actually off the Road Runner network. Cable connection obviously. - I attempted to access 192.168.1.1 with both Mozilla Firefox and IE 8. FIrefox gives an "Unable to connect" error message. IE 8 redirects me to search engine results (yahoo in this case).
-Ipconfig confirms default gateway and DHCP server is 192.168.1.1, subnet mask 255.255.255.0
- I am able to ping the router with <1ms times.
- I have tried resetting router to defaults again, but same issue occurs.
- I am able to get online and access web pages, etc.
- Tried resetting up the router using the Linksys setup program, but it error every time saying "please connect router for broadband"
- Router worked fine with me able to access admin page until it froze up yesterday.
- Wireless works fine. Though the network is unsecure atm, since I can't access router admin.
- I've also tried disconnecting all other devices from the router except my computer and modem. Still wont let me access router. System is running windows 7 PRO, fully updated. However, I can't access the router either on 2 other computers at home which run windows XP PRO SP3. System Specs CPU: Intel i5 running at stock speeds
Mobo: Gigabyte P55-UD4P
Ram: Gskill Ripjaw, 4 gb DDR3-1600 7-7-7-21
HD: Intel X-25 M 80 gb G2.
PSU: Corsair CMPSU 750 TX
GPU: Diamond ATI 5850 Anyone have any ideas on whats wrong here? Did i miss something obvious? Would greatly appreciate any help as having an unsecure wireless network in the middle of NY isn't the best idea. Thanks!
Message Edited by Banthracis on 11-06-2009 04:25 PM

I am once again unable to access the on-line Router admin page. When I use the EasyLink Advisor and click ADVANCED settings it pulls up the browser but goes nowhere. If I type in the address directly it does the same thing. The address I'm typing is correct. I know because if I unplug the router for a minute, I can get on using the EasyLink or entering the address directly into the browser. Then I sign in and can access the pages.
Why do I have to keep resetting the router to access the router admin pages? It doesnt matter about virus protection, firewall, what version of Windows I'm using, what browser I'm using...the only thing that matters is resetting the router.
And now I have a new problem. When I attempt to go online with my new netbook, it causes my wired-to-the-router desktop to loose the connection, even though I reset the router and "added it as a new device".
I was using Homegroup to access the netbook the first day I got it. Now I cannot access the netbook or the network from the netbook, without resetting the stupid router every single time. I am not using mac address filtering and have the router set to allow 9.
Getting fed up with this router and I never get an answer from Linksys as to why I can never access the router admin pages without resetting the stupid router.
I can get the netbook on other people's wireless networks (using their password) but cannot get onto my OWN using my password.
Does anyone have any ideas? I'll try anything before yanking this thing out and buying a different brand of router. Yeah I'm mad, sorry.
Wired desktop Windows 7 Home Premium 64/IE8/using Windows firewall and MS Security Essentials. Netbook is W7 Starter, Norton Internet Security 2010. But none of this matters. Because I had the same problem with this router using Vista64, IE7, no firewall, no a/v, IE32 & 64 bit...all those variables yet the only thing that works is resetting the router.
SO WHAT DOES MATTER? Help me before I trash this thing please.
mlure

WRT54GL unable to access wired shares or printer on PC from wireless iMac

The subject line applies to a new router on which I can access the internet ok both from the wired PC and the wireless iMac.
The problem is this router is unable to access the PC shares or printer from the iMac. Pls note, "this router"!
I have an identical WRT54GL v1.1, same firmware, setup is identical on both, one works with no problem, but the new one has the above problem..
I have spent a day on it and its in line for return on Monday, but I still hope for a miracle tip which may sort it out :-)
On the good one 'Port scan' of the PC from iMac gives me:
Port Scan has started ...
Port Scanning host: 192.168.1.100
Open TCP Port: 139
Open TCP Port: 445
while the faulty one gives me:
Port Scan has started ...
Port Scanning host: 192.168.1.100
..and thats it! No contact.
Yes, the router is set up for 'Lan & Wireless' (no way to change that setting to 'WAN only' it seems, it bounces back to 'Lan & Wireless')
I have btw done a Factory Reset on it (twice) with no joy.
Any ideas anyone?
Mvh

My first guess for this kind of problem would be a software firewall on the computer. The firewall will detect where it is connected and configures the settings depending on the location. Two routers are two different "locations". Try turning off the firewall or even better deinstall it as often some parts of those software firewalls are still active when turned off.
The only option that does affect access of wireless clients to the LAN is the "AP Isolation" option on the "Advanced Wireless Settings". That should be off.
Another thing you could try if you like: do a configuration backup on the working router and restore it to the faulty one. Maybe there are some settings that don't match and that you cannot configure through the web interface. Have you ever used a 3rd party firmware on either of the routers?

Unable to access Home Hub 3.0 router

For some reason I am unable to access the router.
I normally type 192.168.1.254 into the address bar but have started getting the 'Internet Explorer cannot access the web page message'. Doesn't work on Chrome or Safari either.
This was working fine up until a couple of weeks ago - any ideas?

Hi apollo9 and welcome
Try clearing your browser cache (on all 3) or power the hub down for a minute or two, switch it back on, allow all the lights to go blue and try again.
also fwiw, bthomehub.home should work too
-+-No longer a forum member-+-

Is it possible to be connected with a 3G modem for internet access and a WiFi router for printer sharing at the same time?

For our only internet access we have a 3G wireless modem. I have since purchased a WiFi printer and router to connect all the comptuters to in the house. The PCs have no problem with using both the 3G connection and the WiFi signal at the same time to print, however, the MacBook Pro will not connect to the 3G network and the router, it will drop the internet access from the modem and attempt to connect via WiFi (which has no internet access). Is there a solution that is available to remedy this? I attempted to create an adhoc printer network, however, the macbooks again will not print off of this, only the PCs. And I'm getting a bit frustrated overall with this.

The 3G wireless modem is on one of the PC's correct?
Why don't you pass the Internet through the Ethernet port to the router via Cat5 cable, then have that transmit a Wifi signal that everything else can use, then connect the printer to the router for print sharing?
You would have to turn off the wifi on the comptuer with the 3G modem as it's physically connected to the router and can't connect to the other machines as they are all connected to the router for sharing.
The Mac has the ability to pass, Internet Sharing in the System Preferences.
Do you have software for the Mac to run the 3G modem?

HP Photosmart Premium unable to access printer cartridged - no paper jam

HP Photosmart Premium
Hey guys,
I have a printer that I cannot print from - it keeps saying there is a paper jam but when I investigate there is nothing there and I can no longer access the printer cartidge tray (when I open the tray, the cartridge tray no longer moves into the middle).
I have turned off and on etc and there is definately no paper jam - any other thoughts?
Luke

Hi there lukeedwards,
Could you provide the community with a little more information to help narrow troubleshooting? Things like your printer model and your operating system help out a lot.
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

In Mac OS X 10.5.2 I am unable to access all of the HP print options.

I have a HP Photosmart C6150 (a.k.a. C6180) printer, and after the upgrade to 10.5.2, 1/2 of the menu options from the drop down menu where you can adjust settings for the printer don't work. I can select them, but nothing happens. On my iMac G4, the drivers work fine in 10.5.2, but not on my intel iMac. I have deleted the printer and re-added it it. I can't figure what's wrong with it, but it is really frustrating.

This may be an issue with the pde plugins. PDE stands for print dialog extension and are included with vendor drivers to provide access to printer features not supported by the core printing system. If you are using a Power PC driver (or sharing it from the G4 to the MacTel) then that may be a possible cause. See if HP offers a Universal Binary driver for your model.

TS3276 I am unable to access mail on icloud or send mail through the icloud account. How can I get mail routed through the icloud account.

I am unable to access mail on icloud or send mail through the icloud

Here is how to set up your iCloud email account:
http://www.apple.com/support/macosx/mailassistant/

HP Photosmart 7525 - Unable to Communicate with Printer

I set up my printer through the driver provided in the packaging. Everything seemed to be going fine until I try printing anything wirelessly from my computer. The printer claims that it is connected to my internet connection and everything has been configured, but when I try to print anything it says Unable to Communicate with Printer. I have searched through countless troubleshooting forums and cannot find a solution that works, please help!

Hi Star-A-Star,
Thanks for providing that information.
Since the printer is working on the one computer the printer is on the network.
For the other computer follow these steps:
Restart the computer and router.
Make sure the computer is connected to the proper network.
Left click the wireless icon on the taskbar, it shows the network name that you are connected to.
Find out what the IP address is for the computer and the printer.
The first 3 sets of numbers have to match for the printer to get connected to the same network.
Go to start, run, (might have to type run in search window) type cmd, type in ipconfig.
Check the IP address.
Now check the IP address for the printer.
Do the first 3 sets of numbers match?
Try to access the printer's IP address again through Internet Explorer.
Then run the add printer wizard on the computer.
Go to start, devices and printers.
Open the add printer wizard.
Select local printer and uncheck automatic detect.
Next.
Select use the following port, select create new port, choose HP standard TCP/IP,
add TCP wizard comes up, next type in the IP address for the printer and continue the wizard.
Make sure the printer is online.
Try printing a document.
Let me know the results.
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

HP LaserJet 4000tn: "Unable to connect to printer" (IP printing)

The two Leopard machines on my LAN (one wired, one wireless) have trouble printing to my trusty LaserJet 4000tn. Panther, Tiger, and Windows XP machines work fine.
The printer is on the LAN and I'm trying to access it with IP printing. It gets stuck at "Unable to connect to printer; will retry in 30 seconds…"
If I power-cycle the printer, it will print the job.

I've just read through the thread and I might know what the problem is. Your printer is probably getting an IP address dynamically (using DHCP). I've found this to be a problem in some environments because the printer will sometimes suddenly get a new IP address and the computers, having received a specific IP address when they were configured, can't find the address. As a matter of course, when I install a new network printer I allocate a specific address to it. The downside is that your router's DHCP configuration will have to be redone to save a couple of IP addresses for the manual allocation.

Unable To Communicate With Printer HP Officejet Pro 8600 (Network)

I recently purchased an HP Officejet Pro 8600. One morning a couple weeks ago I tried to print something and I received a prompt saying "Unable to Communicate with Printer (Network)". I turned off the printer and turned it back on which did not help, I then turned off my wireless network, turned it back on and still nothing. I finally figured out that I first have to turn off the printer, then turn off my wireless router wait thirty seconds, turn the router back on and the turn the printer back on. After these steps my printer was working. The next morning the same thing happened "Unable to Communicate with Printer (Network)" and I've been replaying Groundhog's Day ever since.
Please help!

Hello msheehy-
I would like to help you with this issue. It sounds like the router is changing the ip address of the printer. This could be caused by a couple reasons. (ip lease time, power loss to the router) I would recommend looking at the following link. http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03781399&cc=us&dlc=en&lc=en&product=4323648&tmp...
I think if you would set a static ip address in the printer EWS you would better off. I hope this helps.
Also, remember a click on the Kudos star to the left is a quick "Thanks" for a helpful post.
Please select the "Accept as Solution" button on the post that best answers your question.
I appreciate your input !
Thank You,
Donald

Unable to access public ip from branch vpn (Cisco ASA 5510 Firewall)

                   Hi,
As per the above diagram
in Head office - able to access public ips
In Branch office - unable to access public ips only accessing head office servers and internet is shared from head office.
please see the below configuration in Branch office router:
access-list 1 permit any
access-list 100 remark ****** Link to Firewall-HO1 ******
access-list 100 permit ip 10.21.211.0 0.0.0.255 172.16.35.0 0.0.0.255
access-list 100 permit ip 10.21.211.0 0.0.0.255 10.10.0.0 0.0.255.255
access-list 100 permit ip 10.21.211.0 0.0.0.255 10.11.0.0 0.0.255.255
access-list 100 permit ip 10.21.211.0 0.0.0.255 10.12.0.0 0.0.255.255
access-list 100 permit ip 10.21.111.0 0.0.0.255 172.16.35.0 0.0.0.255
access-list 100 permit ip 10.21.111.0 0.0.0.255 10.10.0.0 0.0.255.255
access-list 100 permit ip 10.21.111.0 0.0.0.255 10.11.0.0 0.0.255.255
access-list 100 permit ip 10.21.111.0 0.0.0.255 10.12.0.0 0.0.255.255
access-list 100 permit ip 10.21.10.0 0.0.0.255 172.16.35.0 0.0.0.255
access-list 100 permit ip 10.21.10.0 0.0.0.255 10.10.0.0 0.0.255.255
access-list 100 permit ip 10.21.10.0 0.0.0.255 10.11.0.0 0.0.255.255
access-list 100 permit ip 10.21.10.0 0.0.0.255 10.12.0.0 0.0.255.255
access-list 100 permit ip 10.21.211.0 0.0.0.255 host 78.93.190.226
access-list 100 permit ip 10.21.111.0 0.0.0.255 host 78.93.190.226
access-list 100 permit ip any any
access-list 101 deny   ip 10.21.211.0 0.0.0.255 10.10.0.0 0.0.255.255
access-list 101 deny   ip 10.21.211.0 0.0.0.255 10.11.0.0 0.0.255.255
access-list 101 deny   ip 10.21.211.0 0.0.0.255 10.12.0.0 0.0.255.255
access-list 101 deny   ip 10.21.211.0 0.0.0.255 172.0.0.0 0.255.255.255
access-list 101 deny   ip 10.21.111.0 0.0.0.255 10.10.0.0 0.0.255.255
access-list 101 deny   ip 10.21.111.0 0.0.0.255 10.11.0.0 0.0.255.255
access-list 101 deny   ip 10.21.111.0 0.0.0.255 10.12.0.0 0.0.255.255
access-list 101 deny   ip 10.21.111.0 0.0.0.255 172.0.0.0 0.255.255.255
access-list 101 deny   ip 10.21.10.0 0.0.0.255 10.10.0.0 0.0.255.255
access-list 101 deny   ip 10.21.10.0 0.0.0.255 10.11.0.0 0.0.255.255
access-list 101 deny   ip 10.21.10.0 0.0.0.255 10.12.0.0 0.0.255.255
access-list 101 deny   ip 10.21.10.0 0.0.0.255 172.0.0.0 0.255.255.255
access-list 101 permit ip host 10.21.211.51 any
access-list 101 permit tcp 10.21.211.0 0.0.0.255 host 66.147.240.160 eq pop3
access-list 101 permit tcp 10.21.211.0 0.0.0.255 host 66.147.240.160 eq smtp
access-list 101 permit tcp 10.21.211.0 0.0.0.255 host 78.93.56.10 eq pop3
access-list 101 permit tcp 10.21.211.0 0.0.0.255 host 78.93.56.10 eq smtp
access-list 102 permit ip 10.21.211.0 0.0.0.255 any
route-map nonat permit 10
match ip address 101
Thanks for your valuable time and cosiderations

any1 can help me ?

Unable to access/lan2lan ping from VPN Fortigate to Cisco ASA 5505

Problem : Unable to access user A to user B
User A --- router A (122, fortigate 80c) --- (Site to Site VPN between fortigate & cisco asa) --- router B (93, cisco Asa 5505{in front asa got cisco800[81] before to internet} ) --- User B
After using wizard to configure the cisco ASA site to site VPN, the site-to-site tunnel is up.
Ping is unsuccessful from user A to user B
Ping is successful from user B to user A, data is accessable
After done the packet tracer from user A to user B,
Result :
Flow-lookup
Action : allow
Info: Found no matching flow, creating a new flow
Route-lookup
Action : allow
Info : 192.168.5.203 255.255.255.255 identity
Access-list
Action : drop
Config Implicit Rule
Result - The packet is dropped
Input Interface : inside
Output Interface : NP Identify Ifc
Info: (acl-drop)flow is denied by configured rule
Below is Cisco ASA 5505's show running-config
ASA Version 8.2(1)
hostname Asite
domain-name ssms1.com
enable password ZZZZ encrypted
passwd WWWW encrypted
names
name 82 B-firewall description Singapore office firewall
name 192.168.1.0 B-inside-subnet description Singapore office internal LAN IP
name 192.168.200.0 A-inside-VLAN12 description A-inside-VLAN12 (fortinet)
name 192.168.2.0 fw-inside-subnet description A office internal LAN IP
name 122 A-forti
interface Vlan1
nameif inside
security-level 100
ip address 192.168.5.203 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 93 255.255.255.240
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name ssms1.com
object-group network obj_any
network-object 0.0.0.0 0.0.0.0
access-list inside_nat0_outbound extended permit ip any 80 255.255.255.240
access-list inside_nat0_outbound extended permit ip fw-inside-subnet 255.255.255.0 B-inside-subnet 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.5.0 255.255.255.0 A-inside-VLAN12 255.255.255.0
access-list outside_cryptomap extended permit ip fw-inside-subnet 255.255.255.0 B-inside-subnet 255.255.255.0
access-list Outside_nat-inbound extended permit ip A-inside-VLAN12 255.255.255.0 192.168.5.0 255.255.255.0
access-list Outside_nat-inbound extended permit ip host A-forti 192.168.5.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 192.168.5.0 255.255.255.0 A-inside-VLAN12 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-631.bin
no asdm history enable
arp timeout 14400
global (outside) 101 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 101 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 81 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http B-inside-subnet 255.255.255.0 inside
http fw-inside-subnet 255.255.255.0 inside
http 0.0.0.0 255.255.255.255 outside
http 0.0.0.0 0.0.0.0 outside
http 192.168.5.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer A-forti
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 2 match address outside_cryptomap
crypto map outside_map 2 set peer B-firewall
crypto map outside_map 2 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 20
authentication pre-share
encryption aes-192
hash md5
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption aes-256
hash md5
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 192.168.5.10-192.168.5.20 inside
dhcpd dns 165 165 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
username admin password XXX encrypted privilege 15
tunnel-group 122 type ipsec-l2l
tunnel-group 122 ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
class-map outside-class
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
message-length maximum client auto
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
policy-map outside-policy
description ok
class outside-class
inspect dns
inspect esmtp
inspect ftp
inspect h323 h225
inspect h323 ras
inspect icmp
inspect icmp error
inspect netbios
inspect rsh
inspect rtsp
inspect sip
inspect skinny
inspect sqlnet
inspect sunrpc
inspect tftp
inspect xdmcp
service-policy global_policy global
service-policy outside-policy interface outside
prompt hostname context
Cryptochecksum: XXX
: end
Kindly need your expertise&help to solve the problem

any1 can help me ?

Unable to Access Web Site (with same name) outside of Local Network

Hi everyone,
I have my web site (and some other services) hosted outside of my network by my hosting provider, but handle all other items using OS X Server on my network (i.e. Wiki and so forth).
The problem is now that I am unable to access my website at www.mydomain.com from within the network. I have external DNS set up for www.mydomain.com to point to my website, while mydomain.com points to my OS X Server (static IP address). Internally in OS X Server's DNS settings this used to work when I had www.mydomain.com resolving to the IP address of my web host, in addition to the default domain settings that OS X had set up. For some reason this is no longer working, and I am unable to figure out why.
Using latest version of OS X Server 3.0.2.
Any help is greatly appreciated. Thanks!
Update: this ended up being a redirect issue on the web host. I added another subdomain that was hosted externally, and it worked fine. For some reason my web host is redirecting www.mydomain.com to domain.com.

I am in Texas and cannot get to that site either. Do you know for sure the site is up and working? It could just be down (for days, a site I support was down for almost 4 full days a few weeks ago due to a virus problem).
This may (again, may) be your problem: I see you have a173.48.x.x (you really should x-out the last two octets of your IP address for privacy reasons), I am on a 173.74.x.x address; I know some people have had problems with getting to some sites now that they have a 173.x.x.x address. I think Verizon obtained addresses in that range and some of the addresses apparently previously belonged to spammers or some malicious folks.Some sites (web sites, intermeidate routers, etc.) blocked those addresses, and may not have updated their filters to remove the block on those addresses because they don't know that Verizon now owns them. If this is the problem, eventually those filters will get updated and you will be able to access the site, but this could be a fairly long time.
If you know how to contact that site I suggest you email them about the problem. You can also try turning off your router overnight and when you turn it back on the next day you may find that you have a different address (one that doesn't start with 173) that will allow you to get to the site.
I don't think there is much Verizon can do to help, it is not their site that is blocking your address (at least I don't think it is).
Hope this helps.
Justin
Verizon FiOS TV, Internet, and phone
IMG 1.6.2, Build 08.58
Keller, TX 76248

Unable to load HP printer driver-Error message!

Hi,
Just wondering if anyone can be of any assistance.
I recently purchased a HP Photosmart 2575 all-in-one printer and installed the necessary software, which said it was successfully installed. However, whenever I boot up the G3 I keep getting the following message 'Unable to load the printer drive, open the applications Get Info dialog and increase the preferred memory size. If this does not help try quitting all other applications or reinstalling the printer software.'
After clicking ok on this message about four times the message goes and I am able to print fine. Just wondering why this is happening. I have increased the memory allocation and also turnt on the virtual memory to see if this makes any difference, but all to no avail. I have also uninstalled and then reinstalled the software to see if this makes a difference, but that didn't help either.
Any help would be greatly appreciated.
Thanks in advance
PS: The printer is connected via ethernet on my router to enable me to print from another machine

Use Techtool Lite or Trash*Desktop (TD may delete Finder comments )to rebuild your desktop w/extensions off. Does a better job than manually & you avoid all the finger gymnatics. You just have to hold down the shift key to shut off extensions.
Restart to turn the extensions back on again.
If you want to rebuild manually, see KB article http://docs.info.apple.com/article.html?artnum=10182 Rebuilding Desktop File and Icon Recovery.

Unable to access HP printer to router

Similar Messages

Maybe you are looking for