Unable to access the Time Statements in ESS Portal

The user is getting a critical error(com.sap.pcuigp.xssfpm.java.FPMRuntimeException) when trying to access his time statements from ESS portal. The user recently moved to a different country and trying to access statement there. Are there any country specific paramaters that are needed to be changed or set when a employee is reallocated?
Please help me.

Hi Rafi,
We are also facing similar kind of issue.
When i select type of leave as annual it is giving an error message as
" Parameter missing in call of method BUILD_ACTOR_SELECT_CLAUSE in class CA_PT_REQ_ACTOR "
But when i select some other leave type and click review it is working fine, again if i click on previous step and change the leave type to annual it is working fine without giving any error message.
Please let us know how you have solved your issue?
Thanks.
-Suresh

Similar Messages

I have an external hard drive from my time capsule that stopped working on me. I am attempting to access the data with a hard drive reader on my MAC. I am able to see the drive in disk utility and under system info USB. But I am unable to access the data.

I have an external hard drive from my time capsule that stopped working on me. I am attempting to access the data with a hard drive reader on my MAC. I am able to see the drive in disk utility and under system info USB. But I am unable to access the data and it does not show on the desktop when connected.

Ok if disk utility was able to verify the drive I doubt there is any problem.. are you trying to open a TM backup??
You need to mount the sparsebundle then check the actual info inside the bundle.
Don't use disk warrior.. if the disk has verified then unless you deliberately deleted files there is nothing that is going to do.
Pondini has a lot of stuff about getting access to the sparsebundle.
http://pondini.org/TM/17.html
But if you have copied info to the TC that is now gone.. and the disk is ok.. I am not sure.. the TC will not have deleted the files itself.

After updating Firefox yesterday I have been unable to access the internet. I have tried the Norton 360 fix several times, but it still doesn't work. How can I get Firefox working again?

After updating Firefox yesterday I have been unable to access the internet. I have tried the Norton 360 fix several times, but it still doesn't work.

After updating Firefox yesterday I have been unable to access the internet. I have tried the Norton 360 fix several times, but it still doesn't work.

Under Snow Leopard I used a WD My World NAS to back up my Mac Pro (Mid 2010). When I upgraded to Lion I am unable to access the backup because the NAS does not yet support AFP. I have now bought a Time Capsule and want to transfer the old backup onto it.

Under Snow Leopard I used a WD My World NAS to back up my Mac Pro (Mid 2010). When I upgraded to Lion I am unable to access the backup because the NAS does not yet support AFP. I have now bought a Time Capsule and want to transfer the old backup onto it.
How can I recover the NAS back up to put on my new Time Machine.
Talking to Apple Support Adviser was a waste of time on case number 239647273
Any thoughts or pointers?

Keep the old OS around and just kick the tires and test new OS. Apple has a history and habit of breaking support in things like this.
You can use TimeMachine as one level of backup, and even there there were changes with Lion, I would always recommend foremost backup clones of every volume. And clone (SuperDuper etc) can be stored on something like HP NAS Media Server which also was supporting TimeMachine, iTunes - until Apple made that harder and more their own proprietary format.
Apple AirPort Time Capsule Support
Lion Communities
Cloning as a Backup Strategy
Rather than "upgrade" I would clone the system, and do a clean install, then allow Setup Assistant to import your files.
Others who are asking the same question:
http://www.bing.com/search?q=mac+os+x+lion+WD+My+World+NAS

Wrt54g ver5, unable to access the config pages

wrt54g ver5
firmware ver 1.02.5
i am unable to access the internal web pages on wrt54g ver 5
can access the internet fine. it seems to be a memory corruption problem
i has been doing more and more times

Since the router works, it is doubtful (but still possible) that the firmware is corrupted. More likely there is another explanation for your problem. Here are my tips for viewing your router's web pages:
You do not need an Internet connection. The router's "web pages" are built into the router.
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
Point your browser to 192.168.1.1 , then login to your router. Your user name should be left blank. Your password is "admin" (with no quotes), unless you changed it.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
Some Zone Alarm users have reported that adding 192.168.1.1 to their list of "trusted" addresses fixed the problem. This trick might also work with other firewalls.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Report back with this problem, and also state the make and exact model number of your modem (not the router).
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
If you still have trouble, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.

I have just sought to update my lightroom and am now unable to access the develop function and get a note stating that I have reduced functionality what it this about and how do I get my product back

I have just sought to update my lightroom and am now unable to access the develop function and get a note stating that I have reduced functionality what it this about and how do I get my product back

Hi there
I have version 5.7 and every time I opened it I was told that updates are available and to click on the icon to access these. Instead it just took me to the
adobe page with nowhere visible to update. I then sought to download lightroom cc and this is when I could not access the 'develop' section due to reduced
functionality It was apparent that my photos had been put in cc but no way to access them unless I wanted to subscribe.
I have since remedied the problem as my original lightroom 5.7 icon is still available on the desktop and have gone back to that. I do feel that this is a bit
of a rip off and an unnecessary waste of my time though.
Thank you for your prompt reply by the way.
Carlo
Message Received: May 04 2015, 04:52 PM
From: "dj_paige" <[email protected]>
To: "Carlo Bragagnolo" <[email protected]>
Cc:
Subject: I have just sought to update my lightroom and am now unable to access the develop function and get a note stating that I have
reduced functionality what it this about and how do I get my product back
dj_paige created the discussion
"I have just sought to update my lightroom and am now unable to access the develop function and get a note stating that I have reduced functionality what it
this about and how do I get my product back"
To view the discussion, visit: https://forums.adobe.com/message/7510559#7510559
>

Unable to access the data from Data Management Gateway: Query timeout expired

Hi,
Since 2-3 days the data refresh is failing on our PowerBI site. I checked below:
1. The gateway is in running status.
2. Data source is also in ready status and test connection worked fine too.
3. Below is the error in System Health -
Failed to refresh the data source. An internal service error has occurred. Retry the operation at a later time. If the problem persists, contact Microsoft support for further assistance.
Error code: 4025
4. Below is the error in Event Viewer.
Unable to access the data from Data Management Gateway: Query timeout expired. Please check 1) whether the data source is available 2) whether the gateway on-premises service is running using Windows Event Logs.
5. This is the correlational id for latest refresh failure
is
f9030dd8-af4c-4225-8674-50ce85a770d0
6.
Refresh History error is –
Errors in the high-level relational engine. The following exception occurred while the managed IDataReader interface was being used: The operation has timed out. Errors in the high-level relational engine. The following exception occurred while the
managed IDataReader interface was being used: Query timeout expired.
Any idea what could have went wrong suddenly, everything was working fine from last 1 month.
Thanks,
Richa

Never mind, figured out there was a lock on SQL table which caused all the problems. Once I released the lock it PowerPivot refresh started working fine.
Thanks.

UNABLE TO ACCESS THE INTERNET FROM LOCAL PROVIDER ON A SITE-TO-SITE VPN CONNECTION

Dear All,
I have a site-to-site connection from point A to point B. From point B i am unable to access the internet from local internet provider.
I am trying to ping from 192.168.20.1 the dns 8.8.8.8 but i receive the message "destination net unreachable".
When i run "show ip nat translation" i receive nothing.
The vpn connection is working properly, i can ping the other side 192.168.10/24
Below is the configuration of the cisco router on point B.
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.21.254
ip dhcp pool voice
network 192.168.21.0 255.255.255.0
default-router 192.168.21.254
option 150 ip 192.168.5.10
ip cef
ip domain name neocleous.ru
ip inspect name IOS_FIREWALL tcp
ip inspect name IOS_FIREWALL udp
ip inspect name IOS_FIREWALL icmp
ip inspect name IOS_FIREWALL h323
ip inspect name IOS_FIREWALL http
ip inspect name IOS_FIREWALL https
ip inspect name IOS_FIREWALL skinny
ip inspect name IOS_FIREWALL sip
no ipv6 cef
multilink bundle-name authenticated
vty-async
isdn switch-type primary-net5
redundancy
crypto isakmp policy 5
hash md5
authentication pre-share
group 2
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
lifetime 28800
crypto isakmp policy 50
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key Pb85heuvMde9Wdac5Qohha7lziIf142u address [ip address]
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 10
crypto ipsec transform-set TRANSET esp-aes esp-sha-hmac
crypto ipsec transform-set TRANSET2 esp-des esp-md5-hmac
crypto ipsec df-bit clear
crypto map CryptoMAP1 ipsec-isakmp
set peer [ip address]
set transform-set TRANSET
match address CryptoACL
interface FastEthernet0/0
description Primary Provider
ip address [PUBLIC IP MAIN PROVIDER] 255.255.255.252
ip access-group outside_acl in
ip mtu 1390
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
crypto map CryptoCY
crypto ipsec df-bit clear
interface FastEthernet0/1
description TO LAN
no ip address
load-interval 30
speed 100
full-duplex
interface FastEthernet0/1.1
description DATA VLAN
encapsulation dot1Q 20
ip address 192.168.20.254 255.255.255.0
ip access-group inside_acl in
ip nat inside
ip inspect IOS_FIREWALL in
ip virtual-reassembly in
ip tcp adjust-mss 1379
interface FastEthernet0/1.2
description VOICE VLAN
encapsulation dot1Q 21
ip address 192.168.21.254 255.255.255.0
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface FastEthernet0/3/0
no ip address
ip access-group outside_acl in
ip nat outside
ip virtual-reassembly in
shutdown
duplex auto
speed auto
crypto map CryptoCY
ip local pool VPNPool 192.168.23.2 192.168.23.10
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source list nat_list interface FastEthernet0/3/0 overload
ip route 0.0.0.0 0.0.0.0 [default gateway ip]
ip access-list standard VTY
permit 192.168.20.0 0.0.0.255
ip access-list extended CryptoACL
permit ip 192.168.20.0 0.0.0.255 192.168.3.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.5.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.6.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.12.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.2.0 0.0.0.255
permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255
permit ip host 192.168.22.1 192.168.5.0 0.0.0.255
permit ip host 192.168.20.1 192.168.5.0 0.0.0.255
permit ip host 192.168.22.1 192.168.6.0 0.0.0.255
ip access-list extended DFBIT_acl
permit tcp any any
ip access-list extended inside_acl
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.35
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.39
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.23
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.18
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.55
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.144
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.146
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.141
permit ip host 192.168.20.253 host 192.168.3.21
permit ip host 192.168.20.254 host 192.168.3.21
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.10
permit ip 192.168.20.0 0.0.0.255 host 192.168.20.254
ip access-list extended nat_list
deny ip host 192.168.20.254 192.168.10.0 0.0.0.255
deny ip host 192.168.20.254 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.10.0 0.0.0.255
deny ip host 192.168.20.2 192.168.3.0 0.0.0.255
deny ip host 192.168.20.2 192.168.10.0 0.0.0.255
permit ip host 192.168.20.1 any
permit ip host 192.168.20.2 any
permit ip host 192.168.20.254 any
ip access-list extended outside_acl
permit gre any host [ip address]
permit esp any host [ip address]
deny ip any any
ip sla 2
icmp-echo 192.168.10.254 source-interface FastEthernet0/1.1
frequency 180
timeout 500
ip sla schedule 2 life forever start-time now
logging 192.168.3.21
route-map DFBIT_routemap permit 10
match ip address DFBIT_acl
set ip df 0
route-map ISP2 permit 10
match ip address nat_list
match interface FastEthernet0/3/0
route-map nonat permit 10
match ip address nonat_acl
route-map ISP1 permit 10
match ip address nat_list
match interface FastEthernet0/0

You cannot access internet, because all traffic is tunneled for VPN !!!!
Please see cisco tech documentation and bypass traffic for internet.
eg. if lan traffic is going from site a to site b then through vpn
else
lan traffic to internet (any) should be out thorugh the vpn .

HTTP adapter - Unable to access the following endpoint(s): REPLACE_WITH_ACTUAL_URL

Hi All,
Hope you all doing good.
I had a simple but a bit unresolved issue.
I am using soa suite 11.1.1.5 for calling a service which only accepts HTTPS POST requests.
I used HTTP adapter to call that with required security applied.
when I tested the process, the calling is not getting successful but the process goes in running state for 2 mins, and then fails with the error: Unable to access the following endpoint(s): REPLACE_WITH_ACTUAL_URL
End point URL not reachable, and the URL after this.
But there is 500 error message in the called service server log with the same user.
I tried changing lot of things without success.
Can anyone of you guide me, what could be going wrong here.
Hope I get some solution .,
Thanks in advance,
Best Regards

Hi,
The process will receive the request as SOAP message. Then the process will call the service which accpets HTTPS POST message.
I dont know, how to verify whether my service call out to service goes through POST method of HTTP adapter?
But verb used is POST, http.payload is xml.
Thanks & Regards
Chandru

Regarding time statement in ESS

hi gurus,
i have developed time statement in PE51 name ZF03,BUT IN ess the time statement is coming from
tc-hrforms,which is totally different from ZF03,what i want that my form-ZF03 will display in ESS for this what sud i do how will i configure zf03 instead of form from "HRFORMS".
PLZ help me as i already searched alot in th forum but didnt get my answer.

You can't show a PE51 form. SAP has provided standard HR forms which you need to copy to your requirement.
You can do this without much abap knowlege as HRFORMS transaction is a logical nested loop of condition. Go to the layout of the copied form and customize as you want.

Ref: Unable to access the endpoint(s): In BPEL

Hi,
Here My requirement is, I wants Invoke WSDL into my Composite.
My is Domain like http://s008apl011001:7001.
But that WSDL is in diff Domain like http://v110aplffc002: 8001.
This time I am getting below Error:
Non Recoverable System Fault :
Unable to access the following endpoint(s): http://v110aplffc002:8001/soa-infra/services/default/ContentManagement/ContentManagement_ep
I am using SOA suite version 11.1.1.6.
In my composite I have added below security policies like below
<reference name="ContentManagement"
ui:wsdlLocation="http://v110aplffc002:8001/soa-infra/services/default/ContentManagement/ContentManagement.wsdl">
<interface.wsdl interface="http://www.absa.co.za/afs/ContentManagement#wsdl.interface(contentMgt_ptt)"/>
<binding.ws port="http://www.absa.co.za/afs/ContentManagement#wsdl.endpoint(ContentManagement_ep/execute_pt)"
location="ContentManagement_ep.wsdl" soapVersion="1.1">
*<wsp:PolicyReference URI="oracle/wss_username_token_client_policy"*
orawsp:category="security" orawsp:status="enabled"/>
*<property name="oracle.webservices.auth.password">p$ssword01</property>*
*<property name="oracle.webservices.auth.username">weblogic</property>*
*<property name="weblogic.wsee.wsat.transaction.flowOption"*
type="xs:string" many="false">WSDLDriven</property>
*<property name="oracle.webservices.proxyHost" type="xs:anyURI"*
many="false" override="may"> http://v110aplffc002</property>
*<property name="oracle.webservices.proxyPort" type="xs:integer"*
many="false" override="may">8001</property>
*<property name="oracle.webservices.local.optimization" type="xs:boolean"*
many="false" override="may">true</property>
</binding.ws>
</reference>
Then deployed SOA server,It's deployed successfully. At testing time it's throwing below Error :
Non Recoverable System Fault :
<bpelFault><faultType>0</faultType><remoteFault xmlns="http://schemas.oracle.com/bpel/extension"><part name="summary"><summary>oracle.fabric.common.FabricInvocationException: Unable to access the following endpoint(s): http://v110aplffc002:8001/soa-infra/services/default/ContentManagement/ContentManagement_ep</summary></part><part name="detail"><detail>Unable to access the following endpoint(s): http://v110aplffc002:8001/soa-infra/services/default/ContentManagement/ContentManagement_ep</detail></part><part name="code"><code>null</code></part></remoteFault></bpelFault>
Please any one provide solutions for above error.
What I do for above error.
Thanks in Advance
Regards
Anil

Looks like http://v110aplffc002: 8001 is not accessible from http://s008apl011001:7001. if s008apl011001 is windows server check from the browser if you are able to access http://v110aplffc002:8001/soa-infra/services/default/ContentManagement/ContentManagement_ep?WSDL and see the wsdl file. if linux then try curl and see if you can access the wsdl . Most likely the url on v110aplffc002:8001 is not accessible from s008apl011001 .

Unable to access the Internet over 3G Network, Wi-Fi fine.

Hi there,
I'm unable to access the internet on the iPhone 3G over the 3G network. Wi-Fi is fine, no problems there, but every time I try to bring up a website in Safari over 3G I get the message "Safari can't open the page because it is not connected to the Internet".
I have Enable 3G 'ON' under Settings > General > Network, and I have full strength on the signal meter in the top left of the Home screen. I'm in a city (Melbourne, Australia) on the Optus network, so the network itself shouldn't be the issue.
I've tried resetting the Network Settings under Settings > Reset > Reset Network Settings, but it didn't change anything. Any other ideas?
Cheers.

Well, there you go, fixed! Called Optus Customer Service and they were actually helpful! Apparently there were "some components in their back-end that needed to be installed manually." The man wasn't sure why they weren't there, "glitches, blah, blah..." but at least they're there now and I have 3G access.

UNABLE to access the Filter Gallery

Good morning,
Per this screen shot, I am unable to view or access the filter gallery and I would very much like to.
The history portion of the screen shot shows my workflow.
First I opened an image and then opened a Curves adjustment layer. Because I only wanted to change the luminosity values, I then changed the Blending Mode from Normal to "Luminosity". Then I made a minor Curves adjustment, followed by forming a new layer via copy of my original background layer.
At that time, I was unable to access the filter gallery.
I therefore converted that layer I had just created into a smart object but, as the screen shot demonstrates, am still unable to access the filter gallery.
Any thoughts? I am running CS6 on a Mac and I am working in Adobe RGB image mode, 16 bit.
Matt Dubuque

Additionally, your assertion that having this layer saved as a smart object as the cause of the problem seems incorrect.
For example, I can use artistic filters on this layer of an 8-bit image, which is a smart object.
Are there any ARTISTIC plug ins available that work in 16 bit?

I am unable to access prior Time Machine backups.

I am unable to access prior Time Machine backups. I can see previous backups when I enter TM but they do not respond when I click on them. My TM is backing backups and at one time I was able to access them. I am logged on to my Mac Pro as the admin. I am running 10.9.5 and the TM disk is an internal 2 TB drive with 12 GB free.

The 12 GB free may be the cause.
Also see:
http://pondini.org/TM/Troubleshooting.html

IPad2 is locked because of error message "iCloud Backup is unable to access the account. Review your account information in Settings."

I changed my AppleID password and now my iPad2 is locked with a message... "iCloud Backup is unable to access the account. Review your account information in Settings." It will not allow me to unlock the device or go to settings or ignore the message. Suggestions?
<Email Edited by Host>

I have the exact same problem. I have since gone into iCloud via my PC to reset my iCloud password, but did not help. Can someone pls help!!!!!!!!!!!

Unable to access the Time Statements in ESS Portal

Similar Messages

Maybe you are looking for