Unable to access web setup from 4 different Win7 machines with IE9 / FireFox
I Hope someone can help, I suspect this may have something to do with a recent update to Windows or IE since this worked at least a couple of months ago.
I'm unable to access the web setup screen from 4 different windows machines running IE 9 or Firefox (various combinations of wireless, wired, etc.). When I get to the certificate error and hit the "yes, i understand, continue", it comes back with a 'can't be reached' page and looking into the details says the 'connection was dropped'. However If I connect from a MacBook / safari, I'm able to reach the page fine (and admin the router).
Summary:
Using a wrt610n
I am connected to the router, the ip address hasn't changed, the password hasn't changed
I can use the router & connect to the internet
I have the router set to require HTTPS, but switching it to allow HTTP doesn't help.
Both Wired & Wireless Win 7 / IE9 machines can't connect.
Tried setting the router ip address to 'trusted' zone in IE
Tried setting the router ip address to the 'compatibility' mode in IE
Tried using latest version of Firefox with the same results.
Thanks in Advance!
Stephen
Before I suggest you any troubleshooting steps, I would like to ask few question. Like did you try opening the “https://192.168.1.1” in Internet Explorer 8. If not, then try to open the Router Management page in the same manner in Internet Explorer 8 and check whether it opens or not. As it should show up.
Similar Messages
-
Purchase Order created from different client machine with same login ID
Hi,
Purchase Order created from different machine using same Login ID. How to trace IP address of that Machines.
Thanks
HemanthHi;
Please review:
Re: sql to get Machine IP
Regard
Helios -
Unable to access the data from Data Management Gateway: Query timeout expired
Hi,
Since 2-3 days the data refresh is failing on our PowerBI site. I checked below:
1. The gateway is in running status.
2. Data source is also in ready status and test connection worked fine too.
3. Below is the error in System Health -
Failed to refresh the data source. An internal service error has occurred. Retry the operation at a later time. If the problem persists, contact Microsoft support for further assistance.
Error code: 4025
4. Below is the error in Event Viewer.
Unable to access the data from Data Management Gateway: Query timeout expired. Please check 1) whether the data source is available 2) whether the gateway on-premises service is running using Windows Event Logs.
5. This is the correlational id for latest refresh failure
is
f9030dd8-af4c-4225-8674-50ce85a770d0
6.
Refresh History error is –
Errors in the high-level relational engine. The following exception occurred while the managed IDataReader interface was being used: The operation has timed out. Errors in the high-level relational engine. The following exception occurred while the
managed IDataReader interface was being used: Query timeout expired.
Any idea what could have went wrong suddenly, everything was working fine from last 1 month.
Thanks,
RichaNever mind, figured out there was a lock on SQL table which caused all the problems. Once I released the lock it PowerPivot refresh started working fine.
Thanks. -
TS3276 i am unable to open web pages from email links on my ipad
I am unable to open web pages from email links on my ipad
A few more details might help, if nobody else recognizes this.
What happens when you try to open the links?
Can you post an example of a link that doesn't work?
Is there any particular source for the mail with the (bad) links, or is mail from all sources failing?
If you happen to know it, what's the format of the mail message? (Maybe the message is an image?)
Do the embedded links work as expected from an OS X system running Mail.app, or some system and some other other mail client?
To view the link in iOS: if you press on and hold your finger on an embedded link in most contexts, iOS will show a pop-up with the link contents, and will offer to copy it. You can use that to acquire and post the link. If pressing and holding on the link doesn't offer the pop-up, the format of the link itself may not be valid, or it might not really be a link. -
UNABLE TO ACCESS THE INTERNET FROM LOCAL PROVIDER ON A SITE-TO-SITE VPN CONNECTION
Dear All,
I have a site-to-site connection from point A to point B. From point B i am unable to access the internet from local internet provider.
I am trying to ping from 192.168.20.1 the dns 8.8.8.8 but i receive the message "destination net unreachable".
When i run "show ip nat translation" i receive nothing.
The vpn connection is working properly, i can ping the other side 192.168.10/24
Below is the configuration of the cisco router on point B.
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.21.254
ip dhcp pool voice
network 192.168.21.0 255.255.255.0
default-router 192.168.21.254
option 150 ip 192.168.5.10
ip cef
ip domain name neocleous.ru
ip inspect name IOS_FIREWALL tcp
ip inspect name IOS_FIREWALL udp
ip inspect name IOS_FIREWALL icmp
ip inspect name IOS_FIREWALL h323
ip inspect name IOS_FIREWALL http
ip inspect name IOS_FIREWALL https
ip inspect name IOS_FIREWALL skinny
ip inspect name IOS_FIREWALL sip
no ipv6 cef
multilink bundle-name authenticated
vty-async
isdn switch-type primary-net5
redundancy
crypto isakmp policy 5
hash md5
authentication pre-share
group 2
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
lifetime 28800
crypto isakmp policy 50
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key Pb85heuvMde9Wdac5Qohha7lziIf142u address [ip address]
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 10
crypto ipsec transform-set TRANSET esp-aes esp-sha-hmac
crypto ipsec transform-set TRANSET2 esp-des esp-md5-hmac
crypto ipsec df-bit clear
crypto map CryptoMAP1 ipsec-isakmp
set peer [ip address]
set transform-set TRANSET
match address CryptoACL
interface FastEthernet0/0
description Primary Provider
ip address [PUBLIC IP MAIN PROVIDER] 255.255.255.252
ip access-group outside_acl in
ip mtu 1390
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
crypto map CryptoCY
crypto ipsec df-bit clear
interface FastEthernet0/1
description TO LAN
no ip address
load-interval 30
speed 100
full-duplex
interface FastEthernet0/1.1
description DATA VLAN
encapsulation dot1Q 20
ip address 192.168.20.254 255.255.255.0
ip access-group inside_acl in
ip nat inside
ip inspect IOS_FIREWALL in
ip virtual-reassembly in
ip tcp adjust-mss 1379
interface FastEthernet0/1.2
description VOICE VLAN
encapsulation dot1Q 21
ip address 192.168.21.254 255.255.255.0
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface FastEthernet0/3/0
no ip address
ip access-group outside_acl in
ip nat outside
ip virtual-reassembly in
shutdown
duplex auto
speed auto
crypto map CryptoCY
ip local pool VPNPool 192.168.23.2 192.168.23.10
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source list nat_list interface FastEthernet0/3/0 overload
ip route 0.0.0.0 0.0.0.0 [default gateway ip]
ip access-list standard VTY
permit 192.168.20.0 0.0.0.255
ip access-list extended CryptoACL
permit ip 192.168.20.0 0.0.0.255 192.168.3.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.5.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.6.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.12.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.2.0 0.0.0.255
permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255
permit ip host 192.168.22.1 192.168.5.0 0.0.0.255
permit ip host 192.168.20.1 192.168.5.0 0.0.0.255
permit ip host 192.168.22.1 192.168.6.0 0.0.0.255
ip access-list extended DFBIT_acl
permit tcp any any
ip access-list extended inside_acl
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.35
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.39
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.23
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.18
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.55
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.144
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.146
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.141
permit ip host 192.168.20.253 host 192.168.3.21
permit ip host 192.168.20.254 host 192.168.3.21
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.10
permit ip 192.168.20.0 0.0.0.255 host 192.168.20.254
ip access-list extended nat_list
deny ip host 192.168.20.254 192.168.10.0 0.0.0.255
deny ip host 192.168.20.254 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.10.0 0.0.0.255
deny ip host 192.168.20.2 192.168.3.0 0.0.0.255
deny ip host 192.168.20.2 192.168.10.0 0.0.0.255
permit ip host 192.168.20.1 any
permit ip host 192.168.20.2 any
permit ip host 192.168.20.254 any
ip access-list extended outside_acl
permit gre any host [ip address]
permit esp any host [ip address]
deny ip any any
ip sla 2
icmp-echo 192.168.10.254 source-interface FastEthernet0/1.1
frequency 180
timeout 500
ip sla schedule 2 life forever start-time now
logging 192.168.3.21
route-map DFBIT_routemap permit 10
match ip address DFBIT_acl
set ip df 0
route-map ISP2 permit 10
match ip address nat_list
match interface FastEthernet0/3/0
route-map nonat permit 10
match ip address nonat_acl
route-map ISP1 permit 10
match ip address nat_list
match interface FastEthernet0/0You cannot access internet, because all traffic is tunneled for VPN !!!!
Please see cisco tech documentation and bypass traffic for internet.
eg. if lan traffic is going from site a to site b then through vpn
else
lan traffic to internet (any) should be out thorugh the vpn . -
How to access form objects from different class?
Hello, I am new to java and i started with netbeans 6 beta,
when i create java form application from template i get 2 classes one ends with APP and one with VIEW,
i put for example jTextField1 with the form designer to the form and i can manipulate it's contents easily from within it's class (let's say it is MyAppView).
Question>
How can i access jTextField1 value from different class that i created in the same project?
please help. and sorry for such newbie question.
Thanks Mikehmm now it says
non static variable jTree1 can not be referenced from static context
My code in ClasWithFormObjects is
public static void setTreeModel (DefaultMutableTreeNode treemodel){
jTree1.setModel(new DefaultTreeModel(treemodel));
and in Class2 it is
ClasWithFormObjects.setTreeModel(model); -
Unable to access Web Method after deploying into the server
Hi,
I'm Unable to access Web method after deploying into the server.
My Web method is
[WebMethod]
[ScriptMethod(ResponseFormat = ResponseFormat.Json )]
public object getOwners()
DataTable dt = _qbObj.returnDDLData("employeedetails", "EmpID", "EmpFirstName");
if (dt == null)
return new { Result = "Error", Options = "Error getting data" };
string[] strAttributes = { "ID", "Name" };
string[] strColName = { "EmpID", "EmpFirstName" };
List<SolOwners> lstObject = convertToList(dt, strAttributes, strColName, new SolOwners());
var owners = lstObject.Select(c => new { DisplayText = c.Name, Value = c.ID });
return new { Result = "OK", Options = owners };
When I.m accessing that method after deploying into server, I got following error.
System.InvalidOperationException: There was an error generating the XML document. ---> System.InvalidOperationException: <>f__AnonymousType9`2[System.String,System.Collections.Generic.IEnumerable`1[<>f__AnonymousTypea`2[System.String,System.String]]] cannot be serialized because it does not have a parameterless constructor.
at System.Xml.Serialization.TypeScope.GetTypeDesc(Type type, MemberInfo source, Boolean directReference, Boolean throwOnError)
at System.Xml.Serialization.XmlSerializationWriter.CreateUnknownTypeException(Type type)
at System.Xml.Serialization.XmlSerializationWriter.WriteTypedPrimitive(String name, String ns, Object o, Boolean xsiType)
at Microsoft.Xml.Serialization.GeneratedAssembly.XmlSerializationWriter1.Write1_Object(String n, String ns, Object o, Boolean isNullable, Boolean needType)
at Microsoft.Xml.Serialization.GeneratedAssembly.XmlSerializationWriter1.Write71_anyType(Object o)
at System.Xml.Serialization.XmlSerializer.Serialize(XmlWriter xmlWriter, Object o, XmlSerializerNamespaces namespaces, String encodingStyle, String id)
--- End of inner exception stack trace ---
at System.Xml.Serialization.XmlSerializer.Serialize(XmlWriter xmlWriter, Object o, XmlSerializerNamespaces namespaces, String encodingStyle, String id)
at System.Xml.Serialization.XmlSerializer.Serialize(TextWriter textWriter, Object o, XmlSerializerNamespaces namespaces)
at System.Web.Services.Protocols.XmlReturnWriter.Write(HttpResponse response, Stream outputStream, Object returnValue)
at System.Web.Services.Protocols.WebServiceHandler.WriteReturns(Object[] returnValues)
at System.Web.Services.Protocols.WebServiceHandler.Invoke()Please help me to solve that issue.Thank you.Hi Vani,
What project are you developing? According to your code looks like an Asp.Net application? Am i right?
If so , please repost in ASP.Net Forum
http://forums.asp.net for more efficient responses.
This forum is discuss problems of C# development.
Have a nice day!
Kristin
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
Can anybody tell how to access web service from Message Driven bean
Can anybody tell how to access web service from Message Driven bean
Can anybody tell how to access web service from Message Driven bean
-
I am unable to access intranet on my MacBook Pro 13" with OS X mavericks. Is it possible to use files on the Local Area Network? I use the files on the Local Area Network on my windows computer by typing in the I.P address in the library. Kindly guide me how i can use these files stored over the Local Area Network.
I disabled GateKeeper's automatic blocking of unrecognised developers, and so I was able to install the driver.
The Mobile Connect program is now installed, but the computer still does not recognise the modem.
I also borrowed a USB hub from a friend and it didn't make a difference. -
Hallo,
I just installed LabVIEW 8.2 DSC-Module and tried to configure a OPC Client Instance. I get the Error "Unable to browse OPC Server from the selected machine / Error -2147221163 occurred at GetOPCServerList.vi". I have no OPC-Server installed, but is there no Demo-Server?
Thank you
ThomasThis issue might be related to opcenum not being registered correctly. Please follow the steps explained in this document to fix this problem.
As OPCdemo follows the OPC 1.0 standard it is not supported by the OPC client in LV DSC 8.x which supports OPC 2.0 and 3.0 servers. You can download an OPC 3.0 compliant demoserver from Matrikon.
I hope that helps,
Jochen Klier
National Instruments Germany -
Unable to Access Web Site (with same name) outside of Local Network
Hi everyone,
I have my web site (and some other services) hosted outside of my network by my hosting provider, but handle all other items using OS X Server on my network (i.e. Wiki and so forth).
The problem is now that I am unable to access my website at www.mydomain.com from within the network. I have external DNS set up for www.mydomain.com to point to my website, while mydomain.com points to my OS X Server (static IP address). Internally in OS X Server's DNS settings this used to work when I had www.mydomain.com resolving to the IP address of my web host, in addition to the default domain settings that OS X had set up. For some reason this is no longer working, and I am unable to figure out why.
Using latest version of OS X Server 3.0.2.
Any help is greatly appreciated. Thanks!
Update: this ended up being a redirect issue on the web host. I added another subdomain that was hosted externally, and it worked fine. For some reason my web host is redirecting www.mydomain.com to domain.com.I am in Texas and cannot get to that site either. Do you know for sure the site is up and working? It could just be down (for days, a site I support was down for almost 4 full days a few weeks ago due to a virus problem).
This may (again, may) be your problem: I see you have a173.48.x.x (you really should x-out the last two octets of your IP address for privacy reasons), I am on a 173.74.x.x address; I know some people have had problems with getting to some sites now that they have a 173.x.x.x address. I think Verizon obtained addresses in that range and some of the addresses apparently previously belonged to spammers or some malicious folks.Some sites (web sites, intermeidate routers, etc.) blocked those addresses, and may not have updated their filters to remove the block on those addresses because they don't know that Verizon now owns them. If this is the problem, eventually those filters will get updated and you will be able to access the site, but this could be a fairly long time.
If you know how to contact that site I suggest you email them about the problem. You can also try turning off your router overnight and when you turn it back on the next day you may find that you have a different address (one that doesn't start with 173) that will allow you to get to the site.
I don't think there is much Verizon can do to help, it is not their site that is blocking your address (at least I don't think it is).
Hope this helps.
Justin
Verizon FiOS TV, Internet, and phone
IMG 1.6.2, Build 08.58
Keller, TX 76248 -
Interactive Statement unable to access Web Service
I have a working Flash Builder project from which I generate a nav file which I use to generate an Interactive Statement using a process in Workbench.
The Interactive Statement works fine with all the Flash content and data merged from xml.
When I incorporate using a Web Service in the Flash Builder project code to populate a data grid, and regenerate the nav file to generate the interactive statement, the interactive statement gives the following security error when opened:
Security error accessing url
Destination: DefaultHTTP
It seemed that this issue is related to cross domain policy or something like that, BUT I do not get this error when:
1. I run the Flash Builder project directly from Flash Builder that fires up IE and my flash content works perfectly fine in the HTML wrapper, including the web service call that works fine. This works fine both from the bin-debug and the bin-release folders of my Flash Builder project.
2. I created an AIR application from scratch, and consumed the same webservice as used in the earlier Flash Builder project being used to generate nav file for Interactive Statement. The AIR application also works perfectly fine in invoking the web service and does not give any errors.
Question: Why is my Interactive Statement unable to access the web service and gives the error as mentioned above when the same web service is being accessed and consumed successfully by the same flash content in an html wrapper and in an AIR application. How to make my flash content embedded in the PDF container to access and consume the web service?Hi Muhammad,
Acrobat has different crossdomain restrictions. Try a crossdomain file that looks like to test the connection:
<?xml version="1.0"?>
<!DOCTYPE cross-domain-policy SYSTEM "/xml/dtds/cross-domain-policy.dtd">
<cross-domain-policy>
<site-control permitted-cross-domain-policies="all"/>
<allow-access-from domain="*" to-ports="*" />
<allow-http-request-headers-from domain="*" headers="*"/>
</cross-domain-policy>
Following there are a couple of good articles dealing with web services calls:
http://forums.adobe.com/message/3784114#3784114
http://tv.adobe.com/watch/flex-in-a-week-day-2/retrieving-and-handling-data-using-webservi ce/
http://blogs.4point.com/brad.white/2008/12/4-ways-to-invoke-a-webservice-in-flex-with-mxml -and-actionscript.html
http://blog.flexexamples.com/2008/04/14/calling-a-simple-web-service-from-flex-using-the-w ebservice-class/
Regards,
Oana -
Unable to execute Web Service from SSRS Dataset
Hi,
I am unable to access a Web Service to execute Dataset from MS SSRS. I have created a Dataset that refers to a WebService as a Query. The dataset and Query runs well in DEV environment. However, the following error message is displayed when executing
the Query inQA environment:
An error occurred while executing the query.
Failed to execute web request for the specified URL.
Soap Fault:
The server was unable to process the request due to an internal error. For more information about the error, either turn on IncludeExceptionDetailInFaults (either from ServiceBehaviorAttribute or from the <serviceDebug> configuration behavior)
on the server in order to send the exception information back to the client, or turn on tracing as per the Microsoft .NET Framework 3.0 SDK documentation and inspect the server trace logs. (Microsoft SQL Server Report Designer)
rogram Location:
Server stack trace:
at Microsoft.ReportingServices.DataExtensions.XmlDP.InMemoryCommand.ExecuteWebRequest(ICredentials credentials)
at Microsoft.ReportingServices.DataExtensions.XmlDP.InMemoryCommand.Execute()
at Microsoft.ReportingServices.DataExtensions.XmlDP.InMemoryCommand.<>c__DisplayClass1.<ExecuteReader>b__0()
at Microsoft.ReportingServices.DataExtensions.XmlDP.WebRequestHelper.ExecuteServerCallAsNtUser(ServerCall serverCall, WindowsIdentity ntUser)
at Microsoft.ReportingServices.DataExtensions.XmlDP.InMemoryCommand.ExecuteReader(CommandBehavior behavior)
at Microsoft.ReportingServices.QueryDesigners.MultiThreadedQueryResultsHelper.AsyncExecuteReader(IDbCommand command, CommandBehavior behaviour)
at System.Runtime.Remoting.Messaging.StackBuilderSink._PrivateProcessMessage(IntPtr md, Object[] args, Object server, Int32 methodPtr, Boolean fExecuteInContext, Object[]& outArgs)
at System.Runtime.Remoting.Messaging.StackBuilderSink.PrivateProcessMessage(RuntimeMethodHandle md, Object[] args, Object server, Int32 methodPtr, Boolean fExecuteInContext, Object[]& outArgs)
at System.Runtime.Remoting.Messaging.StackBuilderSink.AsyncProcessMessage(IMessage msg, IMessageSink replySink)
Exception rethrown at [0]:
at System.Runtime.Remoting.Proxies.RealProxy.EndInvokeHelper(Message reqMsg, Boolean bProxyCase)
at System.Runtime.Remoting.Proxies.RemotingProxy.Invoke(Object NotUsed, MessageData& msgData)
at Microsoft.ReportingServices.QueryDesigners.MultiThreadedQueryResultsHelper.ExecuteReaderHandler.EndInvoke(IAsyncResult result)
at Microsoft.ReportingServices.QueryDesigners.MultiThreadedQueryResultsHelper.<>c__DisplayClass1.<ExecuteActiveQueryCallback>b__0()
at Microsoft.ReportingServices.QueryDesigners.QueryResultsGrid.EndExecuteReaderInUiThread(GetDataReaderHandler getDataReaderCallback)
===================================
The remote server returned an error: (500) Internal Server Error.
<s:Envelope xmlns:s="<faultcode">http://schemas.xmlsoap.org/soap/envelope/"><s:Body><s:Fault><faultcode xmlns:a="a:InternalServiceFault</faultcode><faultstring">http://schemas.microsoft.com/net/2005/12/windowscommunicationfoundation/dispatcher">a:InternalServiceFault</faultcode><faultstring
xml:lang="en-US">The server was unable to process the request due to an internal error. For more information about the error, either turn on IncludeExceptionDetailInFaults (either from ServiceBehaviorAttribute or from the <serviceDebug>
configuration behavior) on the server in order to send the exception information back to the client, or turn on tracing as per the Microsoft .NET Framework 3.0 SDK documentation and inspect the server trace logs.</faultstring></s:Fault></s:Body></s:Envelope>
I am looking for a solution to this problem. Any help in this regard will be appreciated.Hi Abhijit PS,
According to your description, when calling a web service on production environment, you get the above error message. Right?
In this scenario, it seems you are calling WCF services. Since it's an internal error, we suggest you enable the IncludeExceptionDetailInFaults to see the detail information about the error. Please refer to the articles below:
How to enable WCF tracing
Turn on IncludeExceptionDetailInFaults while connecting to a WCF service from a
client.
The server was unable to process the request due to an
internal error. For more information.. Turn on IncludeExceptionDetailInFaults
Also please refer to some similar threads below:
Turn on IncludeExceptionDetailInFaults (either from ServiceBehaviorAttribute or from the <serviceDebug> configuration
behavior) on the server
WCF Error The server
was unable to process the request due to an internal error
If you have any question, please feel free to ask.
Best Regards,
Simon Hou -
Unable to access E1 instance from client
Hi All,
Urgency:Yes
Version: E 8.12 Stand alone Demo
I am trying to install JDE E8.12 Stand Alone on a desktop.It's installed and when I click on +'Tools->EnterpriseOne Menu'+ submenu,it redirects me to :'http://localhost:8888/jde/E1Menu.maf' and I can see the home page of E1.
Now I am trying to access the above url from a laptop(basically with the idea that desktop will be a server and laptop as client) by replacing 'localhost' with the IP of the desktop.
I am unable to get the login page with any of thr browsers.
It says: **'The page cannot be displayed'**.
Can anyone let me know what other settings should be done on the desktop or on laptop(client),so that I can access it from my laptop,as E1 being Web-based application.
Any guide on Stand alone installation will be highly appreciated.
Regards,
Nikesh.Hi Murali,
Many thanks for your instant reply.
But when I do the same installation on my laptop,other laptops(who are in the same network) are able to access it and thus the E1 installed on my laptop becomes server.
Meanwhile can you let me know where shall I get a hang of 'OTM-E1' integration.Any supporting guide from E1 side ,if you have,please share.
I read that we would need 'E1 servlet installation instructions' guide.
Thanks.
Regards,
Nikesh. -
I need to change some settings on my WRT54G router (I believe it's v8 and I'm using Vista). When I first set the router up I was able to access the setup (192.168.1.1) just fine. Lately, however, I have been unable to reach it. Every time I try to connect to the router's address the connection times out. I'm not sure why this is happening, as the internet connection itself is working fine. Why can't I access my router?
The 132 address is an Intenet (public) address. I was able to ping it. I assume that it likely belongs to your ISP.
I cannot ping the 10 address. It apparently belongs to the wireless router that you are connecting to. This might be your own wireless router, or perhaps your neighbor's, or a router that belongs to your school.
Since you cannot find the router's setup pages at either of these addresses, I see no way to sort this problem out without resetting the router to factory defaults, and then setting up the router again from scratch. Since you are at college, I assume that other students have had similar setup issues. Perhaps one of your friends could help you with this.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, go ahead and try to setup the router manually, and see if you can get your router setup and working. You said you have a complicated setup there at college, so I doubt that the setup disk that came with the router will work (unless it worked for you the first time).
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your router's version, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Maybe you are looking for
-
Xorg 1.5.3 - Still some issues with the keyboard layout
well i read a lot of threads and i solved almost everything, but my keyboard layout is still a little strange, for example, before the "backslash" key (the one above the TAB key) doesn't work anymore, that really bothers me because i really use the m
-
If I copy and paste a comment in a pdf, when I create an xfdf file the copied comment isn't included. Is there a way to add these copied comments to the xfdf file?
-
Editing application-j2ee-engine.xml file in Web Dynpro DC
I'd like to set one of my web dynpro apps to automatically start whenever the J2EE engine is started. <a href="http://help.sap.com/saphelp_erp2005/helpdata/en/94/0a5b422f786255e10000000a155106/frameset.htm">This SAP Library document</a> states that y
-
Erreur à l'ouverture et à l'enregistrement d'un fichier dans Dreamweaver cc 2014.1
windows 8.1 Dreamweaver cc 2014.1 6947 build Bonjour, Suite à la mise à jour de Dreamweaver cc 2014.1, j'ai des alertes à chaque ouverture et fermeture de fichier (voir captures ci-dessous). J'ai désinstallé et installé de nouveau l'application sans
-
Smart Folder Bug: Iphoto fails to match using 'filename' filter
Hi, this issue has popped up here: http://discussions.apple.com/message.jspa?messageID=6008267 and here: http://www.mac-forums.com/forums/showthread.php?t=22401 though I've yet to find an answer. Briefly, the problem: When using a smart album with a