Unable to add SNMP server in WLC 5508 with 7.4.110
hi
I am trying to add 0.0.0.0/0 as SNMP address and netmask and i am getting an error saying the netmask is invalid.
is there a different way to set this?
Hi Roy,
This is strange.
I do not have a test WLC with this code to test, but command syntax is correct. I have verified it on my test controller in 7.0.116.0 & it is happy to accept it. Even 7.4 config guides does not show any other command syntax for this.
http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/consolidated/b_cg74_CONSOLIDATED_chapter_0111.html
One good thing is, this is the default setting once you create a snmp-community. It should have 0.0.0.0/0 as subnet/net mask & you do not require any changes for the default config.
"show snmpcommunity" output should show the config values for your SNMP community.
If you are trying to change it from configured subnet to default value, then as a work around you can re-create the snmp commnuity from fresh (delete & recreate)
If you have Cisco TAC assistance then log a case with them to see why this command is not accepting in your code of WLC
HTH
Rasika
**** Pls rate all useful responses ****
Similar Messages
-
Trying to get home sharing working on a corporate wireless network. Cisco wireless.
WLC5508 controller
Cisco 3502 access points
All apple devices on same WLAN - security WPA2-PSK
ITunes account up to date
All devices laterst software.
Can ping apll tv from laptop
can ping apple tv from ipad
Can ping ipad from laptop
can ping laptop from ipad.
Apple tv never sees any other device.
Any ideas?Fascinating just reading about your setup. I have a WRT350N and have noticed that it will drop its speed, sometimes down to 1Mbps. It seems to do so at about the same time every day, but usually comes back to speed in about 5 minutes. In my experience, the Apple TV will disconnect if the speed falls this low. Try monitoring the Linksys with Netstumbler, Vistumbler, or just in the Windows Network utility.
Check the "lease obtained" and "lease expired" times for your router to see if that is when the network fails. I've just finished reading an angry thread over at the Linksys forum about the WRT330N where someone mentioned that the router wasn't renewing its lease.
"I cannot set it run off automatic DHCP from the WRT330N, the router will not assign it an IP every time the lease expires, causing me to have to manually set an IP on the Print server. That's annoying. Having the router drop IP's to individual machines after 12-48 hours...very annoying."
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread .id=67412
If that is the problem, then I would consider setting up a Static IP address for your Apple TV. You can do that through the user interface -> Settings -> Network -> Configure ... (Quite intuitive as you only have change IP address and the subsequent details remain the same.)
My router assigns IP Addresses in the ranges of 192.168.1.100 ->149. The idea here is to choose an address outside of that range but is not greater than 192.168.1.253 (and should not end in the number 1). You shouldn't have to change the linksys router as long as 50 clients are assigned in that range. You'll have to figure that out by accessing your router webpage at browser address 192.168.1.1 -> the default password is "admin" (without the quotes).
Good luck. -
WLC 5508 with LAP-1142n - Several Errors
Hello all,
I had installed a WLC 5508 with 7 LAP 1142n and 2 converted AP 1131abg.
I am seeing some errors relating 2 issues.
1st- One particular AP 1142 is disassociating and reseting the radios.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thu Oct 28 11:50:49 2010
AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:1(802.11a) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:46 2010
AP's Interface:1(802.11a) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to Init. Status:NA
Thu Oct 28 11:50:46 2010
AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to Init. Status:NA
Thu Oct 28 11:50:46 2010
AP 'AP3', MAC: e8:04:62:23:ac:e0 disassociated previously due to AP Reset. Uptime: 1 days, 10 h 24 m 23 s . Last reset reason: operator changed 11g mode.
Thu Oct 28 11:50:35 2010
AP Disassociated. Base Radio MAC:e8:04:62:23:ac:e0
Thu Oct 28 11:50:35 2010
AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
Thu Oct 28 11:50:35 2010
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
I had some search, and the new discovery cause, might be that the AP didnt know what WLC do associate, in a multi-controller environment. This is not the case. I only have one WLC in the same management vlan.
2st-The Radius server is beeing related in the logs as been deactivated. I raise the server time-out on Radius configuration option, but it still continues to do it.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thu Oct 28 10:24:41 2010
RADIUS server 10.67.128.36:1812 deactivated in global list
Thu Oct 28 10:24:41 2010
RADIUS server 10.67.128.36:1812 failed to respond to request (ID 172) for client e8:06:88:51:c0:2b / user 'unknown'
Is this meaning the WLC stop sending request to the Radius Server ? We dont have BackUp Radius.
As far as i know, its always the same mac-address client that is associated to that error, maybe a iphone.
I had so many clients in that SSID and they are all working good.
The Radius server is a NPS from windows Server 2008
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
, and the client says that the medium response time is 0,02 sec, so im wondering why the controller is not getting response from Radius for a particular client?! My client also says, that didnt found any log related to that mac-address client ... what is weird...
WLC with last software available 7.0.164
Hope some one help me here.
Best Regards,
Bruno PetrónioThanks Scott,
I understand what you are mentioning, and i really didnt do it yet.
I realize that the primary controller was not configured on the
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Wireless –> All APs –> High Availability tab, and did it only to the AP that is taking this beahviour.
Is this mandatory for a 1 controller only ?
No mather what the manual say, after that the AP is rebooting 2 mins in 2 mins... with the same kind of messages.
The interface on the switch is getting a few input errors and the same numbers of crc... but are so few...
Next step ... i will change it to another one's place/pathing cable.
Regarding the Radius messages... any ideas ?
I'm already on 30 sec's of server timeout.
Best Regards,
Bruno Petrónio -
Deployment of WLC-5508 with 2702i-D have performance issue.
Hi Team,
We have centrally deployed WLC-5508 with 50 AP licence along with HA scenario. we have 3 locations.
1- HQ. have 26 AP with POWINJ5.
2- Branch location A- 8 AP with POWINJ5.
3. Branch location B have 8 AP with POWINJ4.
my exception is to achieve that single SSID with dynamic VLAN from group police (NPS). MY HO have 26 AP and those are working in local mode.
and branches are connected through flexconnect mode. and all are working with different-2 NPS.
Now i am facing a problem with this deployment are following.
1- branch A have performance issue.
2- HQ have performance issue.
3- i don't want to go with dedicated NPS for every location.
In order to achieve this deployment i want only single SSID with primary and secondary NPS at my HQ with dynamic VLAN for respective departmental users vlans..
above is my problem and concern. otherwise i am successfully achieving this solution with dedicated NPS with single group policy. but when i am going forward to achieve my expectation that time i am facing authentication issue at my HQ and sometimes am not able to get proper VLAN IPs. at my HQ.
kindly help me in that to understand where I am doing wrong things to achieve my expectation.
Thanks.
NalinI am facing 2 different problems.
1st issue- in existing setup we have throughput issue. (while downloading or uploading any data from the internet or Intranet, that time wireless clients are facing slowness of the Speed. and same time when i am trying from LAN i am not facing any issue)
2nd Issue- I want to achieve only single SSID with primary and secondary NPS (AD group is bind with vlan Attributes) with dynamic VLAN for respective departmental users.
for Issue no 2 i have created SSID to achieve the single ssid parameter for every location. in order to achieve i have change all access points mode local to Flexconnect mode after that i have created AP groups location wise and then create flexconnect Groups where i have mapped all the vlan through AAA VLAN-ACL mapping. created interface group and mapped all the vlans in that group.
for more understanding please go through the below mentioned CLI view.
Cisco Controller) >show wlan apgroups
Total Number of AP Groups........................ 4
Site Name........................................ GURGAON-AP-GROUP
Site Description................................. GURGAON-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Pol icy
3 gurgaon-interface Disabled None
--More-- or (q)uit
4 gurgaon-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
GUR-AP-01 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:e4 default location 1 IN 1
GUR-AP-05 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b5:18 default location 1 IN 1
GUR-AP-03 2 AIR-CAP2702I-D-K9 bc:16:65:13:71:00 default location 1 IN 1
GUR-AP-07 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:f8 default location 1 IN 1
GUR-AP-06 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:e0 default location 1 IN 1
GUR-AP-08 2 AIR-CAP2702I-D-K9 f4:4e:05:45:78:98 default location 1 IN 1
GUR-AP-02 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:2c default location 1 IN 1
GUR-AP-04 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:64 default location 1 IN 1
GUR-AP-09 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b4:44 default location 1 IN 1
Site Name........................................ MUMBAI-AP-GROUP
Site Description................................. MUMBAI-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
--More-- or (q)uit
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-7-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:d8 7th Floor 1 IN 3
--More-- or (q)uit
FAL-7-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:18 7th Floor 1 IN 1
FAL-7-AP14 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ad:e8 7th Floor 1 IN 1
FAL-7-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:4c 7th Floor 1 IN 1
FAL-7-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:bc 7th Floor 1 IN 1
FAL-7-AP13 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:80 7th Floor 1 IN 1
FAL-7-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:94 7th Floor 1 IN 1
FAL-7-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:e8 7th Floor 1 IN 1
FAL-7-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:f0 7th Floor 1 IN 3
FAL-7-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:e4 7th Floor 1 IN 1
FAL-7-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:84 7th Floor 1 IN 3
FAL-7-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:14 7th Floor 1 IN 1
FAL-7-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:c8 7th Floor 1 IN 3
FAL-7-AP11 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:08 7th Floor 1 IN 1
Site Name........................................ MUMBAI-THIRD-FLOOR-AP
Site Description................................. MUMBAI-THIRD-FLOOR-AP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
--More-- or (q)uit
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-3-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:a4 3rd Floor 1 IN 3
FAL-3-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:94 3rd Floor 1 IN 3
FAL-3-AP11 2 AIR-CAP2702I-D-K9 f4:0f:1b:73:00:74 3rd Floor- Eurek 1 IN 3
FAL-3-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:d0 3rd Floor 1 IN 3
--More-- or (q)uit
FAL-3-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b5:88 3rd Floor 1 IN 3
FAL-3-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:9c 3rd Floor 1 IN 3
FAL-3-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:af:a0 3rd Floor 1 IN 1
FAL-3-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:fc 3rd Floor- Eurek 1 IN 3
FAL-3-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:28 3rd Floor 1 IN 3
FAL-3-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:f4 3rd Floor 1 IN 3
FAL-3-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:8c 3rd Floor 1 IN 2
FAL-3-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:f4 3rd Floor 1 IN 3
Site Name........................................ RAHEJA-AP-GROUP
Site Description................................. RAHEJA-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
--More-- or (q)uit
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
5 raheja-interface Disabled None
2 raheja-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-RAHEJA-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:1c Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:37:3c Confrennce Room 1 IN 3
FAL-RAHEJA-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:48 Near Confrence R 1 IN 3
FAL-RAHEJA-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:c0 Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:a0 Near Server Room 1 IN 3
FAL-RAHEJA-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:20 Reception Area 1 IN 3
FAL-RAHEJA-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:68 USER BAY ROAD si 1 IN 1
FAL-RAHEJA-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:d4 Training Room 1 IN 1
--More-- or (q)uit
Site Name........................................ default-group
Site Description................................. <none>
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
3 gurgaon-interface Disabled None
4 gurgaon-guest Disabled None
5 raheja-interface Disabled None
6 test Disabled None
Cisco Controller) >show flexconnect group summary
FlexConnect Group Summary: Count: 4
Group Name # Aps
Gurgaon-AP 9
HQ-3RD-FLR-AP-GROUP 12
HQ-7THFLR-AP-GROUP 14
Raheja-AP-Group 8
(Cisco Controller) >show flexconnect group detail Gurgaon-AP
Number of AP's in Group: 9
bc:16:65:13:71:00 GUR-AP-03 Joined Flexconnect
f4:4e:05:45:78:98 GUR-AP-08 Joined Flexconnect
f4:4e:05:78:ae:64 GUR-AP-04 Joined Flexconnect
f4:4e:05:78:ae:e4 GUR-AP-01 Joined Flexconnect
f4:4e:05:80:b3:2c GUR-AP-02 Joined Flexconnect
f4:4e:05:80:b3:e0 GUR-AP-06 Joined Flexconnect
f4:4e:05:80:b3:f8 GUR-AP-07 Joined Flexconnect
f4:4e:05:80:b4:44 GUR-AP-09 Joined Flexconnect
f4:4e:05:80:b5:18 GUR-AP-05 Joined Flexconnect
Efficient AP Image Upgrade ..... Disabled
Master-AP-Mac Master-AP-Name Model Manual
Group Radius Servers Settings:
Type Server Address Port
Primary Unconfigured Unconfigured
Secondary Unconfigured Unconfigured
--More-- or (q)uit
Group Radius AP Settings:
AP RADIUS server............ Disabled
EAP-FAST Auth............... Disabled
LEAP Auth................... Disabled
EAP-TLS Auth................ Disabled
EAP-TLS CERT Download....... Disabled
PEAP Auth................... Disabled
Server Key Auto Generated... No
Server Key.................. <hidden>
Authority ID................ 436973636f0000000000000000000000
Authority Info.............. Cisco A_ID
PAC Timeout................. 0
Multicast on Overridden interface config: Disabled
DHCP Broadcast Overridden interface config: Disabled
Number of User's in Group: 0
Vlan :........................................... 203
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 205
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 204
--More-- or (q)uit
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 206
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 207
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 208
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 209
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 210
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 211
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 212
Ingress ACL :................................... None
Egress ACL :.................................... None
--More-- or (q)uit
Vlan :........................................... 216
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 217
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 218
Ingress ACL :................................... None
Egress ACL :.................................... None
Group-Specific FlexConnect Wlan-Vlan Mapping:
WLAN ID Vlan ID
WLAN ID SSID Central-Dhcp Dns-Override Nat-Pat
(Cisco Controller) >
(Cisco Controller) >show wlan summary
Number of WLANs.................................. 6
WLAN ID WLAN Profile Name / SSID Status Interface Name PMIPv6 Mobility
1 FRACTAL-EMP-MUMBAI / FRACTAL Enabled group for mumbai none
2 FRACTAL-GUEST / FRACTAL-GUEST Enabled guest wifi none
3 FRACTAL-EMP-GURGAON / FRACTAL-GURGAON Enabled gurgaon-interface none
4 GURGAON-GUEST / FRACTAL-GUEST-GURGAON Enabled gurgaon-guest none
5 RAHEJA-EMP-WIRELESS / FRACTAL-R Enabled raheja-interface none
6 TEST-SSID / TEST-SSID Enabled test none
hope this will give you proper understanding. -
WLC 5508 with AD, NPS but without GPO, how?
Hi,
I didn't found anything related to what I'm trying to do so I though I would create a new discussion...
I would like to setup a new WLAN and to be able to connect, a user will have to enter his username/password that will be confirmed using NPS and Active Directory. The problem is, I don't want to use a GPO, I would like to only verify if the user is a member of a AD group, let's say "wlan_access".
I don't want to install anything ( certificate, GPO, creating a WLAN configuration ) on the user's PC/laptop, only AD validation using NPS as a Radius server.
If a user is part of that AD group, after he enter his credential he will have access to that WLAN.
Is it possible to setup that? How should I configured the WLAN in my WLC 5508 ( running 7.2.110.0 )? How should I configure NPS ( Windows 2008 R2 Enterprise )?
Thanks a lot for your help and answers.
GuillaumeHi guys,
With the info Stephen Rodriguez gave, it looks like I won't be able to do what we want without doing config on the user's devices ( laptop, ipad, etc.. ).
@Joseph Vasanth Louis Yes the message is from the event viewer of the NPS server. In the connection request policies, there's not much config, I let the option "Authentication Methods" in the tab Settings uncheck, so it won't override the settings in the Network Policies.
I though it was possible to have authentication using NPS and Active Directoy without installing anything on the user's devices and still having a secured wireless network ( not like a hotspot ).
The solution I think is the most workable is with the PEAP or PSK, with a certificate but even that...the user will have to create the WLAN profil on his laptop, so I'm not sure we want to go that way. I'll check for the PSK option, to see if the "Web Authentication" could be done using NPS.
Thanks guys for all your time and help. I'll continue my tests and keep you posted. -
WLC 5508 with version 7.0.98.0 and AIR-LAP1242ag
hi, recently i have deployed wlc 5508 with ap 1262. initially i had trouble with the existing version on the wlc (6..0.199.0) which AIR-LAP1262N-E-K9 was not registering with wlc. i have upgraded the wlc to 6.0.199.4 ver still it was not registering. finally i have upgraded to 7.0.98.0 and all the 40 AP's ( AIR-LAP1262N-E-K9 ) are addedd and its working fine.
Now my issue is, at the same site i have 12 nos of AIR-LAP1242ag autnomous AP's which i need to convert to lightweight ap and register with wlc. where i am stuck currently. after loading the recovery image (c1240-rcvk9w8-tar.123-7.JX9.tar) the ap reboots and can see it register with wlc within seconds contollers pushed the new image and once the ap reboots, never register again.
does anyone has any idea?After adding the country codes GB and RU.. in my test setup 1242 is registered...i will have it run for couple hours and see the result
ref: below
(Cisco Controller) >show ap uptime
Number of APs.................................... 2
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Ethernet MAC AP Up Time Association Up Time
AP1cdf.0f66.79ca 1c:df:0f:66:79:ca 0 days, 00 h 43 m 35 s 0 days, 00 h 42 m 36 s
AP001e.be27.a7e6 00:1e:be:27:a7:e6 0 days, 00 h 16 m 56 s 0 days, 00 h 07 m 15
This issue sorted...thanks -
Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users
Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users
I've been given a fantastic "opportunity" by my boss to use our existing wireless infrastructure to provide internet access to potentially upto 2000 VIP guests arriving with BYOD devices, in a very densely populated area for a 3 day event. We are talking an area of approx 200m x 15m. Think of it as an awards ceremony/concert. The solution will also be mobile so we will be using internet breakout from different telcos as it will move to approx 20 countries. The area is also incredibly densely populated with other wifi APs. I did a brief site survey and AirMagnet could detect over 2500 other 'rogue' APs from where I was stood! I hope CleanAir works!
We need a simple authentication method for them to connect with zero admin from our side. We don't want to just offer up a rolling daily PSK as that's a bit amateur and we don't really want the VIP guests sharing the PSK with others during their stay. Ideally they could self-provision by providing an email address.
I know the WLC can handle webauth for local users but I don't think it scales very well. ie I don't think I can offer the account to several hundred people.
Cisco ISE looks a very expansive (and expensive) product but I don't think we need all it's capabilities (do I?). It would be nice to just ask a potential user for their email address and grant them access and email them next year. I've seen Cisco NAC but that looks over the top too for just guest users who will only be accessing a shared internet connection.
I've seen 3rd party supposed software solutions from Kiosk Antamedia etc do they work with Cisco Enterprise WLC solutions?
We'd like to limit users to a certain (low) bandwidth and block (say) torrent traffic to keep the general user experience worthwhile.
Does anybody have any case study documents or experience of such a project? As well as the authentication it's how well the APs will handle the dense potential number of clients trying to connect in such a confined space.
Any suggestions would be gratefully appreciated from the knowledgeable community.
Cheers,
MikeHi Rasika,
We are having WLC 5508 model with software version running 7.4.121.0. AP Models are AIR-CAP2602I.
Normally our WAN links are good even while the issue pertains. We are connected to remote offices over ipsec site to site vpn for WAN. The link latency in WLC between the AP and the controller shows <1ms.
currently the Guest network is using WPA2-PSK auth given in the controller. we are trying to find a option to make the Guest wireless auth local to the office, and see if this solves the problem.
any suggestions,
Thank you,
Arjun -
Unable to install Windows Server 2012 Feature - [Tools] File Server Resource Manager Tools.
Installs, however when I restart the server error messages appears saying feature unable to install, windows reverting changes.
In the Setup event logs have the following information message "Update FSRM-Infrastructure of package FSRM-All failed to be turned on. Status: 0x800f0922"
Does anyone have any idea's on why this Feature can not be installed ??
ScottHi Shaun
Tried both of your suggestions, however neither strategy worked.
Strategy 1
Tried installing via powershell - "install-windowsfeature -name fs-resource-manager -includemanagementtools"
Feature un-installed itself during the restart.
Attempted to use the command "DISM /online /remove-feature /featurename:FSRM-Infrastructure-Services". However
this did work because one the Service was'nt installed or two because there was no command option for "/remove-feature"
PACKAGE SERVICING COMMANDS:
/Add-Package - Adds packages to the image.
/Remove-Package - Removes packages from the image.
/Enable-Feature - Enables a specific feature in the image.
/Disable-Feature - Disables a specific feature in the image.
/Get-Packages - Displays information about all packages in the image.
/Get-PackageInfo - Displays information about a specific package.
/Get-Features - Displays information about all features in a package.
/Get-FeatureInfo - Displays information about a specific feature.
/Cleanup-Image - Performs cleanup and recovery operations on the image.
Strategy 2
Tried installing via powershell, using the following command DISM
/online /enable-feature /featurename:FSRM-Infrastructure-Services, however got the same result, the install backed out during the restart.
All up back to where I started? -
WLC 5508 running 7.4.110.0 unable to tftp upload config from controller
Hi,
Two WLC 5508 running identical code version. One is 50 license Primary, the second is HA. Identical config on both. HA WLC can upload its config to the TFTP or FTP server but Primary cannot. The operation fails for both CLI and GUI and for different protocols i.e. TFTP, FTP.
#### Primary Controller
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.95.16
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... PRODWC7309
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.1.30.210
Last Reset....................................... Power on reset
System Up Time................................... 18 days 18 hrs 51 mins 35 secs
System Timezone Location......................... (GMT+10:00) Sydney, Melbourne, Canberra
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... AU - Australia
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +17 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 8
Number of Active Clients......................... 138
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 3C:08:F6:CA:52:20
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 50
(Cisco Controller) >debug transfer trace enable
(Cisco Controller) >transfer upload start
Mode............................................. TFTP
TFTP Server IP................................... 10.1.22.2
TFTP Path........................................ /
TFTP Filename.................................... PRODWC7309-tmp.cfg
Data Type........................................ Config File
Encryption....................................... Disabled
*** WARNING: Config File Encryption Disabled ***
Are you sure you want to start? (y/N) Y
*TransferTask: Jun 02 10:41:15.183: Memory overcommit policy changed from 0 to 1
*TransferTask: Jun 02 10:41:15.183: RESULT_STRING: TFTP Config transfer starting.
TFTP Config transfer starting.
*TransferTask: Jun 02 10:41:15.183: RESULT_CODE:1
*TransferTask: Jun 02 10:41:24.309: Locking tftp semaphore, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.393: Semaphore locked, now unlocking, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.393: Semaphore successfully unlocked, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.394: tftp rc=-1, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
pLocalFilename=/mnt/application/xml/clis/clifile
*TransferTask: Jun 02 10:41:24.394: RESULT_STRING: % Error: Config file transfer failed - Unknown error - refer to log
*TransferTask: Jun 02 10:41:24.394: RESULT_CODE:12
*TransferTask: Jun 02 10:41:24.394: Memory overcommit policy restored from 1 to 0
% Error: Config file transfer failed - Unknown error - refer to log
(Cisco Controller) >show logging
*TransferTask: Jun 02 10:41:24.393: #UPDATE-3-FILE_OPEN_FAIL: updcode.c:4579 Failed to open file /mnt/application/xml/clis/clifile.
*sshpmReceiveTask: Jun 02 10:41:24.315: #OSAPI-3-MUTEX_FREE_INFO: osapi_sem.c:1087 Sema 0x2b32def8 time=142 ulk=1621944 lk=1621802 Locker(sshpmReceiveTask sshpmrecv.c:1662 pc=0x10b07938) unLocker(sshpmReceiveTask sshpmReceiveTaskEntry:1647 pc=0x10b07938)
-Traceback: 0x10af9500 0x1072517c 0x10b07938 0x12020250 0x12080bfc
*TransferTask: Jun 02 10:39:01.789: #UPDATE-3-FILE_OPEN_FAIL: updcode.c:4579 Failed to open file /mnt/application/xml/clis/clifile.
*sshpmReceiveTask: Jun 02 10:39:01.713: #OSAPI-3-MUTEX_FREE_INFO: osapi_sem.c:1087 Sema 0x2b32def8 time=5598 ulk=1621801 lk=1616203 Locker(sshpmReceiveTask sshpmrecv.c:1662 pc=0x10b07938) unLocker(sshpmReceiveTask sshpmReceiveTaskEntry:1647 pc=0x10b07938)
-Traceback: 0x10af9500 0x1072517c 0x10b07938 0x12020250 0x12080bfc
#### HA Controller
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.95.16
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... PRODWC7310
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.1.31.210
Last Reset....................................... Software reset
System Up Time................................... 18 days 19 hrs 1 mins 27 secs
System Timezone Location......................... (GMT+10:00) Sydney, Melbourne, Canberra
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... AU - Australia
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +17 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 4
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 3C:08:F6:CA:53:C0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 500
(Cisco Controller) >debug transfer trace enable
(Cisco Controller) >transfer upload start
Mode............................................. FTP
FTP Server IP.................................... 10.1.22.2
FTP Server Port.................................. 21
FTP Path......................................... /
FTP Filename..................................... 10_1_31_210_140602_1050.cfg
FTP Username..................................... ftpuser
FTP Password..................................... *********
Data Type........................................ Config File
Encryption....................................... Disabled
*** WARNING: Config File Encryption Disabled ***
Are you sure you want to start? (y/N) y
*TransferTask: Jun 02 10:51:31.278: Memory overcommit policy changed from 0 to 1
*TransferTask: Jun 02 10:51:31.278: RESULT_STRING: FTP Config transfer starting.
FTP Config transfer starting.
*TransferTask: Jun 02 10:51:31.278: RESULT_CODE:1
*TransferTask: Jun 02 10:52:05.468: ftp operation returns 0
*TransferTask: Jun 02 10:52:05.477: RESULT_STRING: File transfer operation completed successfully.
*TransferTask: Jun 02 10:52:05.477: RESULT_CODE:11
File transfer operation completed successfully.
Not upgrading to 7.4.121.0 because of bug CSCuo63103. Have not restarted the controller yet.
Any one else had this issue ? Is there a workaround ?
Thanks,
Rick.Thanks Stephen, In my deployments of 7.4.110.0 version I have not seen this issue so may be controller reboot will fix it (we do have HA to minimize the impact). I will keep the thread updated with findings and may request TAC for the special release 7.4.121.0 if the still not happy with 7.4.110.0
Rick. -
OVM 3.0.3 - cannot add new server to VLAN group with bonded VLANs
I have a new OVS 3.0.3 server built with 2 bonded interfaces and a single VLAN running on top for the management interface. It gets discovered fine by OVM Manager (I'm running Version: 3.0.3.126, Build: 20111214_126)
I am trying to add it to a VLAN group with two VLANs -- the existing management VLAN (ID=300) plus one other (ID=301). (I already have one identical server assigned to the VLAN group, with both VLAN interfaces configured and running fine.) This works OK, and I can see VLAN 301 for the new server in Oracle VM Manager with no IP address assigned to it.
However, when I try to apply an IP address to the VLAN (via Hardware / Resources / VLAN Groups / Edit VLAN Group / Configure IP Addresses / VLAN Interfaces) it fails with this error:
Job Internal Error (Operation)com.oracle.ovm.mgr.api.exception.FailedOperationException: com.oracle.ovm.mgr.api.exception.FailedOperationException: OVMAPI_4010E Attempt to send command: dispatch to server: whyovmprd02 failed. OVMAPI_4004E Server Failed Command: dispatch https://?uname?:[email protected]:8899/api/1 ovs_br_config start 0004fb0010be2df bond0.301, Status: org.apache.xmlrpc.XmlRpcException: exceptions.RuntimeError:Command ['/etc/xen/scripts/ovs-network-bridge', 'start', 'bridge=0004fb0010be2df', 'netdev=bond0.301'] failed (1): stderr: ovs-network-bridge Start: No such device bond0.301
Oracle VM Manager seems to be expecting the subinterface for VLAN 301 to exist on the server already - which it doesn't of course, because the server has just been built, so it only has its management interface VLAN in place (VLAN ID 300)
I have managed to work around this by removing VLAN segment 301 from the VLAN group completely, then adding it back in with the IP addresses for both servers in place. This seems to convince Oracle VM Manager that it needs to create the bond0.301 subinterface before it configures it. However, I obviously had to shut down all VMs to do this, and it was really messy as VLAN 301 is the storage network, so my original server lost contact with the NFS storage for a while which caused it to fence etc.
There must be another way??! Any pointers would be very much appreciated.Avi Miller wrote:
It's fixed in 3.1. In the meantime, if you can remove and reapply the Virtual Machine role on that network, it'll recreate the bridges for you.Thanks for replying Avi. (I won't ask you for a release date for 3.1 :))
I did try that initially, but it didn't seem to help - I got this error back:
Job Internal Error (Operation)com.oracle.ovm.mgr.api.exception.FailedOperationException: OVMAPI_4010E Attempt to send command: dispatch to server: whyovmprd02 failed. OVMAPI_4004E Server Failed Command: dispatch https://?uname?:[email protected]:8899/api/1 ovs_if_meta bond0.301 ethernet:0004fb00100a35f{why-be-301}:STORAGE, Status: org.apache.xmlrpc.XmlRpcException: exceptions.Exception:ovs_set_metadata: interface /sys/class/net/bond0.301 does not exists
This appears to be from ovs_if_meta in /opt/ovs-agent-3.0/OVSVMNetConfig.py, which looks to be where the agent tries to write out the new roles for the network into the metadata file - it seems to be expecting the VLAN to exist already, and specifically checks in /sys to make sure that it is there.
Should / could I add a step to my kickstart build to force the 301 VLAN to be created maybe? This would bring it into line with the other VLAN that is used for management, which is of course sitting there ready and waiting as soon as the server is built. -
WLC 5508 and 7.4.110.0 and AP Blackhole?
So large customer had WLCs running 7.4.110.0 and it appears there was either a 3500/3600 AP memory leak or a CCKM roaming issue. The APs would occasionally blackhole traffic. You could see 2+ APs at -67dbm in 5GHz. Phones are locked to 5GHz, data rates matched. . Phone showed good strong signal, but 7925 users would report every couple days the phone dropping/DHCP timeout, re-registering, etc. We had a large CSE/TAC group onsite audit the 7925 Deployment Guide and setup, and we did a lot of cleanup but never hit the silver bullet.
After upgrading the 5508 to 7.4.121.4 (TAC special not on Cisco.com) they reported the 7925 problems have improved. Only been 1 day so far.
There is also a WPA2 with Preshared Key CCKM bug with the 7925s that roaming takes 2s. Use either strong WEP or buy 7926s, or use EAP/certificates, etc. https://tools.cisco.com/bugsearch/bug/CSCtt38270
7.4.121.0 Release Notes
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn74mr02.html#wp1142453
We are running daily Traffic Stream Metrics (TSM) reports from Prime/WLC, and exporting the CallManager Diagnositc LQK records (export via CAR) to show if things are improving/etc.Thanks Stephen, In my deployments of 7.4.110.0 version I have not seen this issue so may be controller reboot will fix it (we do have HA to minimize the impact). I will keep the thread updated with findings and may request TAC for the special release 7.4.121.0 if the still not happy with 7.4.110.0
Rick. -
Hi,
I am replacing an old 4400 series WLC running version 4.0.179.11 to a new 5508 WLC running version 7.2.110.0.
We currently have 70 x 1131 Access points on the 4400 WLC.
With this upgrade, do i need to upgrade the old 4400 to version 6.0 so the AP's get an up to date IOS or can i directly migrate all AP's over to the new 5508 without any version incompatabilities on the AP's?
I am abit worried that the AP's are running a very old IOS on the 4400 v.4.0.179.11 to go straight to the new 5508 v.7.2.110.0.
ThanksHi,
Check out this release note
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7_2_110_0.html#wp976667
You'll need to get up to a supported version of 6.0 first as per the release notes.
You'll need to check out the 6.0 release notes too to make sure there are no other intermediate upgrade steps required too.
Nigel
Sent from Cisco Technical Support iPad App -
WLC 5508 with 7.4.100.0 software
Hi All,
One of my client has a wireless setup with WLC 5508 and 1142N APs. It was running with a good coverage for access points when WLC was running with 7.0 software version. Last week I upgraded the software to latest 7.4.100.0 version. After that the coverage of APs are very low.
Can someone help me regarding this issue.
Thanks
SadiqI didn't have coverage issues per say, but my 1142 APs kept disassociating randomly
TAC suggested running these commands. Which has stopped the APs leaving the building.
> config 802.11a disable network
> config 802.11a 11nSupport a-mpdu tx priority all disable
> config 802.11a 11nSupport a-mpdu tx scheduler disable
> config 802.11a enable network
> config 802.11b disable network
> config 802.11b 11nSupport a-mpdu tx priority all disable
> config 802.11b 11nSupport a-mpdu tx scheduler disable
> config 802.11b enable network
Aggregation is the process of grouping packet data frames together rather than transmitting them separately. Two aggregation methods are available: Aggregated MAC Protocol Data Unit (A-MPDU) and Aggregated MAC Service Data Unit (A-MSDU). A-MPDU is performed in the software whereas A-MSDU is performed in the hardware.
Disables the 802.11n-5 GHz A-MPDU transmit aggregation scheduler. -
Emergency Version for WLC 5508 with 6.0.188
The release notes for 6.0.188 talks abt 5.2.157.0 ER.aes. But 5508 does not like the file AIR-WLC4400-K9-5-2-157-0-ER.aes.
How can I get the boot loader on WLC 5508?
On WLC 5508...
Product Version.................................. 6.0.188.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
On WLC 4404
Product Version.................................. 6.0.188.0
RTOS Version..................................... 6.0.188.0
Bootloader Version............................... 4.2.205.0
Emergency Image Version.......................... N/A ----------> Even though I installed 5-2-157-0-ER.aes it does not show here... Bug???Ok. In the release notes of 6.0.188 they should have seperated for 5508.
On WLC 4404
Product Version.................................. 6.0.188.0
RTOS Version..................................... 6.0.188.0
Bootloader Version............................... 4.2.205.0
Emergency Image Version.......................... N/A
When u say "The n/a issue is a bug but its with the primary image, not the ER image"
Do you mean that because my primary image is 6.0.188 which has bug to not take or show the ER image? -
Hello
i need your help
i want to configure Cisco WLC 5508 whith 03 vlans, 3750 as core swich
- management Vlan
- local-user vlan
- Guest Vlan
i want to know all steps or config to do on WLC
thxHi,
Just check this.
It may help u.
Wireless LAN Controller and Lightweight Access Point Basic Configuration Example
http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/69719-wlc-lwap-config.html
http://rscciew.wordpress.com/2014/01/22/configure-dynamic-interface-on-wlc/
Webauth for guest users:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html
http://rscciew.wordpress.com/2014/06/19/wlc-webauth-configuration/
Regards
Maybe you are looking for
-
Lack of integrity from BT Operators
For several months, since installation, we have had an unbelievably awful service from BT. We were already with them, on BT Broadband Option 2 for years, so expected the transition to infinity to go smoothly, which it did up until the engineer left i
-
Here Drive stuck on 'Looking for GPS"
Running version 3.0.4087.0 on Samsung Ativ S (in Canada). Nokia Drive seems to find my location without any issues for a short period of time. Later when launching it just shows "Looking for GPS" in the status bar and cannot find my location at all.
-
AT / SKF report on ksu1 or ksv1 cycle
Hi, In KSU1 or KSV1, we can define var portion type by actual SKF or AT or on plan cycle also. May I know if there is a report to show the var portion type of distribution or assessment cycle is using AT or SKF? It is quite difficult to locate the va
-
Help on currentyear filter in bw universe
hi experts, i am using sap bw and created a universe on it.i want to create webi report on that universe such that it should fetch the current year data.but the thing is,i dont want to use prompt so i want to create a present year filter in the unive
-
How do I get iPhone to recognise phone numbers in Calendar entries?
Does anybody know how can I get iPhone (4S running iOS 5.1.1 with iCloud) to recognise phone numbers in Calendar entries made in Outlook 2010 for PC so that Calendar on iPhone underlines the phone number when the Calendar entry is called up and so th