Unable to attach pictures to texts

Torch 9800.
When I attach a picture to texts I get message "failed to send message".
Until recently was able to send without any problem.

Hi and Welcome to the Community!!
I suggest the following steps, in order, even if they seem redundant to what you have already tried (steps 1 and 2 each should result in a message coming to your BB...please wait for that before proceeding to the next step):
1) Register HRT
KB00510 How to register a BlackBerry smartphone with the wireless network
Please wait for one "registration" message to arrive to your Messages app
2) Resend Service Books
KB02830 Send the service books for the BlackBerry Internet Service
Please wait for "Activation" Messages, one per already configured email account, to arrive in your Messages. If you have no already configured email accounts, please wait 1 hour.
3) Batt Pull Reboot
With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes. See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Hopefully that will get things going again for you! If not, then you should contact your mobile service provider for formal support.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Similar Messages

Unable to send pictures in text messaging

I'm unable to send pictures in text messaging ! My carrier is Consumercellular . I'm able to send pictures to my other iphone but not to my other phone or anyone else out of network! My other phone has no problem with sending to others , just the iphone!?

Consumer Cellular will offer iphone (4s, 5c and 5s again) on December 13, 2013
We have a 4s, 5 and 5s with iOS 7.04 and Consumer Cellular now has APN + a carrier update that will offer MMS = picture messaging

Ever since updating I am unable to attach pictures to emails. I fist noticed in Facebook, but also having the problem with Yahoo, etc

When I updated I can no longer attach photos to emails. I first noticed in Facebook but also in Yahoo, AOL, etc

When I updated I can no longer attach photos to emails. I first noticed in Facebook but also in Yahoo, AOL, etc

My iPhone 4S stopped allowing me to attach picture to texts, some users. The camera icon is still present but it is a lighter gray and when you tap it nothing happens.

The camera icon is still present but it is a lighter shad of grey for only 2 of my contacts. The other contacts I can still attach photographs to. Don't know if accidentally changed settings for those users. I reset my network settings but that didn't work. Any ideas?

What happens when you click More next to Flickr in your last screen shot?

Cannot receive pictures via text

I am unable to receive pictures via text. My phone is a Blackberry Bold 9900. I have no problem sending pictures.

Looking for suggestions.
Thanks

Can anyone recommend an alternative software programme to Pages? I have an OS X 10.7.5 macbook pro, so I am unable to get it. I want a programme that I can create docs with pictures and text on, invitations, posters etc. Many thanks in advance-..

Can anyone recommend an alternative software programme to Pages? I have an OS X 10.7.5 macbook pro, so I am unable to get it. I want a programme that I can create docs with pictures and text on, invitations, posters etc. Many thanks in advance…..

LibreOffice

Kernel 2.6.25 upgrade = MadWifi: unable to attach hardware [SOLVED]

Hello,
After I upgraded my kernel to 2.6.25 on my laptop with an Atheros AR242x, which I use normally use MadWifi with, stopped working. I am unable to get any wifi0 or ath0 device to show up in ifconfig. The most descriptive error I could pull up was "MadWifi: unable to attach hardware: 'Hardware didn't respond as expected' (HAL status 3)" out of dmesg, which you can see below. It was suggested in the IRC channel I compile MadWifi from testing out of abs which I did but it didn't seem to change anything.
Linux version 2.6.25-ARCH (root@architect) (gcc version 4.3.0 (GCC) ) #1 SMP PREEMPT Sat Apr 19 15:39:26 CEST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000037e80000 (usable)
BIOS-e820: 0000000037e80000 - 0000000037e92000 (ACPI data)
BIOS-e820: 0000000037e92000 - 0000000037f00000 (ACPI NVS)
BIOS-e820: 0000000037f00000 - 0000000038000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
894MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at [c00f7c60] 000f7c60
Entering add_active_range(0, 0, 228992) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 228992
HighMem 228992 -> 228992
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 228992
On node 0 totalpages: 228992
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1757 pages used for memmap
Normal zone: 223139 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
DMI present.
ACPI: RSDP 000F7BB0, 0014 (r0 TOSINV)
ACPI: RSDT 37E8AD9E, 0040 (r1 TOSINV TOSINV00 6040000 LTP 0)
ACPI: FACP 37E91D8A, 0074 (r1 TOSINV Bonefish 6040000 ATI F4240)
ACPI: DSDT 37E8BAC8, 62C2 (r1 TOSINV SB450 6040000 MSFT 100000E)
ACPI: FACS 37E92FC0, 0040
ACPI: APIC 37E91DFE, 0050 (r1 TOSINV APIC 6040000 LTP 0)
ACPI: SLIC 37E91E4E, 0176 (r1 TOSINV TOSINV00 6040000 INV 0)
ACPI: MCFG 37E91FC4, 003C (r1 TOSINV MCFG 6040000 LTP 0)
ACPI: SSDT 37E8B5B0, 0518 (r1 PmRef Cpu0Cst 3001 INTL 20050228)
ACPI: SSDT 37E8B351, 025F (r1 PmRef Cpu0Tst 3000 INTL 20050228)
ACPI: SSDT 37E8ADDE, 0573 (r1 PmRef CpuPm 3000 INTL 20050228)
ACPI: DMI detected: Toshiba
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 38000000:a8000000)
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
PM: Registered nosave memory: 00000000000dc000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 00000000000e4000
PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227203
Kernel command line: root=/dev/sda1 ro vga=773
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1729.253 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 902908k/915968k available (2075k kernel code, 12516k reserved, 712k data, 268k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff80000 - 0xfffff000 ( 508 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf7e80000 ( 894 MB)
.init : 0xc03bf000 - 0xc0402000 ( 268 kB)
.data : 0xc0306cf8 - 0xc03b8e80 ( 712 kB)
.text : 0xc0100000 - 0xc0306cf8 (2075 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 3462.16 BogoMIPS (lpj=5768270)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 9k freed
ACPI: Core revision 20070126
ACPI: Checking initramfs for custom DSDT
CPU0: Intel(R) Celeron(R) M CPU 430 @ 1.73GHz stepping 0c
Total of 1 processors activated (3462.16 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
net_namespace: 548 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x7, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled.
ACPI: Power Resource [FN00] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
ACPI: RTC can wake from S4
system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:08: ioport range 0x1080-0x1080 has been reserved
system 00:08: ioport range 0x220-0x22f has been reserved
system 00:08: ioport range 0x400-0x401 has been reserved
system 00:08: ioport range 0x40b-0x40b has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x4d6-0x4d6 has been reserved
system 00:08: ioport range 0x530-0x537 has been reserved
system 00:08: ioport range 0xc00-0xc01 has been reserved
system 00:08: ioport range 0xc14-0xc14 has been reserved
system 00:08: ioport range 0xc50-0xc52 has been reserved
system 00:08: ioport range 0xc6c-0xc6c has been reserved
system 00:08: ioport range 0xc6f-0xc6f has been reserved
system 00:08: ioport range 0xcd4-0xcd5 has been reserved
system 00:08: ioport range 0xcd6-0xcd7 has been reserved
system 00:08: ioport range 0xcd8-0xcdf has been reserved
system 00:08: ioport range 0x8000-0x805f has been reserved
system 00:08: ioport range 0x8210-0x821f has been reserved
system 00:08: ioport range 0xf40-0xf47 has been reserved
system 00:08: ioport range 0x280-0x293 has been reserved
system 00:08: ioport range 0x87f-0x87f has been reserved
system 00:09: iomem range 0xe0000-0xfffff could not be reserved
system 00:09: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:09: iomem range 0x0-0xfff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: 0xc0000000-0xc00fffff
PREFETCH window: 0x00000000d0000000-0x00000000dfffffff
PCI: Bridge: 0000:00:04.0
IO window: disabled.
MEM window: 0xc0100000-0xc01fffff
PREFETCH window: disabled.
PCI: Bus 6, cardbus bridge: 0000:05:06.0
IO window: 0x0000a800-0x0000a8ff
IO window: 0x0000ac00-0x0000acff
PREFETCH window: 0x40000000-0x43ffffff
MEM window: 0x44000000-0x47ffffff
PCI: Bridge: 0000:00:14.4
IO window: a000-afff
MEM window: 0xc0200000-0xc02fffff
PREFETCH window: 0x0000000040000000-0x0000000043ffffff
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Enabling device 0000:05:06.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:05:06.0[A] -> GSI 23 (level, low) -> IRQ 23
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Unpacking initramfs... done
Freeing initrd memory: 541k freed
apm: BIOS not found.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:05.0: Boot video device
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 1536k, total 131072k
vesafb: mode is 1024x768x8, linelength=1024, pages=169
vesafb: protected mode interface info at c000:52fd
vesafb: pmi: set display start = c00c536b, set palette = c00c53a5
vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 268k freed
No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:14.1 to 64
scsi0 : pata_atiixp
scsi1 : pata_atiixp
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8460 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8468 irq 15
Switched to high resolution mode on CPU 0
ata2.00: ATAPI: PIONEER DVD-RW DVR-K17A, 1.50, max UDMA/33
ata2.00: configured for UDMA/33
scsi 1:0:0:0: CD-ROM PIONEER DVD-RW DVR-K17A 1.50 PQ: 0 ANSI: 5
sata_sil 0000:00:12.0: version 2.3
PCI: Enabling device 0000:00:12.0 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 22
scsi2 : sata_sil
scsi3 : sata_sil
ata3: SATA max UDMA/100 mmio m512@0xc0507000 tf 0xc0507080 irq 22
ata4: SATA max UDMA/100 mmio m512@0xc0507000 tf 0xc05070c0 irq 22
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-7: TOSHIBA MK8037GSX, DL230M, max UDMA/100
ata3.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK8037GS DL23 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<4>Driver 'sr' needs updating - please use bus_type methods
sda1 sda2 < sda5 > sda3
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sd 2:0:0:0: [sda] Attached SCSI disk
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
ACPI: AC Adapter [ADP0] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Lid Switch as /class/input/input4
ACPI: Lid Switch [LID]
ACPI: Transitioning device [FAN0] to D3
ACPI: PNP0C0B:00 is registered as cooling_device0
ACPI: Fan [FAN0] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: ACPI0007:00 is registered as cooling_device1
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: LNXTHERM:01 is registered as thermal_zone0
ACPI: Thermal Zone [TZ00] (59 C)
ACPI: LNXTHERM:02 is registered as thermal_zone1
ACPI: Transitioning device [FAN0] to D0
ACPI: Unable to turn cooling device [f78183d8] 'on'
ACPI: Thermal Zone [TZ01] (56 C)
Marking TSC unstable due to: TSC halts in idle.
sr 1:0:0:0: Attached scsi generic sg0 type 5
sd 2:0:0:0: Attached scsi generic sg1 type 0
ACPI: \_SB_.PCI0.IDE_.SECD.S_D0: found ejectable bay
ACPI: \_SB_.PCI0.IDE_.SECD.S_D0: Adding notify handler
ACPI: Error installing bay notify handler
ACPI: Bay [\_SB_.PCI0.IDE_.SECD.S_D0] Added
ACPI: \_SB_.PCI0.IDE_.SECD.S_D1: found ejectable bay
ACPI: \_SB_.PCI0.IDE_.SECD.S_D1: Adding notify handler
ACPI: Error installing bay notify handler
ACPI: Bay [\_SB_.PCI0.IDE_.SECD.S_D1] Added
Linux agpgart interface v0.103
ACPI: device:1f is registered as cooling_device2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
input: Video Bus as /class/input/input5
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 19, io mem 0xc0504000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
8139too Fast Ethernet driver 0.9.28
input: PC Speaker as /class/input/input6
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:13.2: irq 19, io mem 0xc0506000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:05:07.0[A] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: OHCI Host Controller
eth0: RealTek RTL8139 at 0xf8b24800, 00:a0:d1:6d:dc:08, IRQ 20
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 19, io mem 0xc0505000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
Symbol init_mm is marked as UNUSED, however this module is using it.
This symbol will go away in the future.
Please evalute if this is the right api to use, and if it really is, submit a report the linux kernel mailinglist together with submitting your code for inclusion.
[fglrx] Maximum main memory to use for locked dma buffers: 802 MBytes.
[fglrx] ASYNCIO init succeed!
[fglrx] PAT is enabled successfully!
[fglrx] module loaded - fglrx 8.47.3 [Mar 29 2008] on minor 0
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
Yenta: CardBus bridge found at 0000:05:06.0 [1179:ff10]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:05:06.0, mfunc 0x01111002, devctl 0x44
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x0
synaptics: Toshiba Satellite A100 detected, limiting rate to 40pps.
input: SynPS/2 Synaptics TouchPad as /class/input/input7
Yenta: ISA IRQ mask 0x0ef8, PCI irq 23
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff
pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x43ffffff
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
ath5k_pci 0000:02:00.0: registered as 'phy0'
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ath5k phy0: failed to resume the MAC Chip
ACPI: PCI interrupt for device 0000:02:00.0 disabled
ath5k_pci: probe of 0000:02:00.0 failed with error -5
ACPI: PCI Interrupt 0000:05:0a.0[A] -> GSI 22 (level, low) -> IRQ 22
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
hda_codec: Unknown model for ALC660VD/ALC861VD, trying auto-probe from BIOS...
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22] MMIO=[c0200000-c02007ff] Max Packet=[2048] IR/IT contexts=[4/8]
ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
wlan: trunk
ath_pci: trunk
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
MadWifi: unable to attach hardware: 'Hardware didn't respond as expected' (HAL status 3)
ACPI: PCI interrupt for device 0000:02:00.0 disabled
EXT3 FS on sda1, internal journal
NTFS driver 2.1.29 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs error (device sda5): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
Adding 1004052k swap on /dev/sda3. Priority:-1 extents:1 across:1004052k
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00080da0d16ddc08]
warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
hda-intel: Invalid position buffer, using LPIB read method instead.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Last edited by JesseC (2008-04-25 17:25:52)

tomk wrote:
Thanks, I'll add it to my collection.
I expect you blacklisted ath5k, right? Better the devil you know and all that, but I would give ath5k a try sometime. It's in mainline, and will eventually replace madwifi altogether.
Yes I did, I eventually will have to go to ath5k but currently madwifi works without a problem so I see no real reason to move over at the moment. In other words, I'll let someone else be the beta tester on that project

I am unable to attach PDFs to Hotmail/Outlook email using my FF browser today. Never had issue before today.

1. I am unable to attach pdfs today in Outlook/Hotmail email using my Firefox browser (27.0.1). I keep getting an error message that says, "The file is not a picture and can't be inserted inline." I do not understand why I keep getting this error message. I am not attempting to insert an image. I am selecting to Insert Files as Attachments from the drop down menu.
No matter how many times I attempt to attach various pdfs to my emails today using Firefox as my browser, I keep getting this same error message. I have cleared the cache, cleared all cookies, cleared all history, signed out of my Hotmail/Outlook account, signed back in, restarted computer, etc., to no avail. Same problem.
2. I switched to my Safari browser, and have no problem attaching pdfs in my Hotmail/Outlook email account. The pdfs are attaching perfectly as usual. My emails are being sent normally with the attachments. The attached pdfs are being received and are opening perfectly as intended.
3. Why am I unable to attach files with Firefox today? Firefox is my browser of choice and I have used it with my Hotmail/Outlook email account without any problems, till today. Please help me! Thank you!

Thank you jscher2000. Yes my PDFs do contain the .pdf extension. I tried your excellent idea to utilize the drag and drop method, but I still get the same error message with PDFs. I have no problem attaching photos or Word documents with either method; just PDFs.
For further diagnostics, I started composing my email in Safari, attached all my pdfs and saved my email as a Draft. I then went to Firefox, opened the draft to continue working on it, and voila! There are all the pdfs I attached previously while in Safari. I was able to send the email with attachments through Firefox with no issues. The attachments went through and were able to be opened.
I am mystified, as Firefox has been trouble-free with my email account, and I have never had this particular issue till today. I made no changes to anything else on my computer, but I did notice very late last night that Outlook had one of those typical messages at the top of my Inbox to refresh my browser since Outlook had been updated. I refreshed and shut down for the night, and when I rebooted this morning that is when I discovered this brand new glitch with attachments. I'm assuming this has something to do their last update.

Unable to view pictures embeds in emails

unable to view pictures embedded in emails. Any help gratefully received.

Images in received emails are only visible if included in an HTML message.
If they appear as an attachment icon just double-click them and they should open in Preview.

Why am I having trouble sending pictures through text message?

Why am I unable to send a picture through text message? I have an iphone 4s. This never happened with my iphone4. I am about to switch and give my preteen my upgrade and take my old phone back. This was a waste of money. This is with both people who have Iphones and people who don't. (IM and regular text). I can randomly get one to go through, but it usually gets to about 90% and freezes. I can usually upload photos to Facebook. This is such an elementary function for a phone!!!!

1. you should contact your phone carrier as they handle all messaging.
2. Are you provisioned by your carrier for MMS?
3. if you are have you gone into settings to make sure that MMS is turned on.

I got problems with the new ios6 in my 3gs. no picture via text message

recently i download the new version ios6 to my 3gs. since then i cant send picture via text messages.

If you still can't send or receive MMS messages
To send and receive MMS messages on your iPhone, verify that your wireless carrier supports MMS2.
Ensure that MMS Messaging is turned on in Settings > Messages.
Verify that your phone is able to access cellular data.
Some carriers allow you to edit your APN (Access Point Name), which may prevent MMS from working.
If you are roaming outside your calling area, make sure you have Data Roaming turned on in Settings > General > Cellular to send or receive MMS content.
While on a phone call, you will be unable to send or receive MMS messages when using an EDGE, GPRS, or any CDMA cellular data network. After the phone call ends, you will receive any incoming messages. If you tried to send an MMS message, you may need to send it again.
If the issue persists and your wireless carrier has confirmed that your wireless account is provisioned2 for MMS, restore the iPhone.
From Here > http://support.apple.com/kb/TS2755

How do i send picture via text msg?, how do i send picture via text msg?

how do i send picture via text msg?

There is a little button with a picture of a camera on it right next to the text input field in the Messages App. Tap that and you can attach a picture.

Unable to view pictures in mail 3.6 version

Unable to view pictures in mail . have mail version 3.6

Images in received emails are only visible if included in an HTML message.
If they appear as an attachment icon just double-click them and they should open in Preview.

Unable to attach photo in iPhoto library using gmail in Safari

I am unable to attach a photo that is in the iphoto library when I am sending an email from my gmail account in Safari. The way it should work is to go to Compose new emai, then click on attach file which opens a window to navigate to the photos folder. Inside that folder is a iphoto library which has the photo I want to send. It is not possible to open the library and choose the photo! Instead it tries to attach the entire library! I have no problem attaching photos that are in folders in the photos folder.
I know Ican open the photos folder and find the picture and drag it to the message. What I want to do is be able to use the attach file dialogue window. Thanks!!!

From your Safari menu bar click Safari > Preferences then select the Privacy tab.
Click Details then remove all Google related data.
Same for Jimdo.
Then press Command + Option + E to empty the Safari cache.
Quit and relaunch Safari then try Gmail or Jimdo.
If that didn't help ..
Open a Finder window. From the Finder menu bar click Go > Go to Folder
Type or copy paste the following:
~/Library/Caches/com.apple.Safari/Cache.db
Click Go then move the Cache.db file to the Trash.
Quit and relaunch Safari. Try Gmail to test.

After the recent update, my documents moved from Finder to Word. When I moved the folders to Finder, I am unable to attach a file to an e-mail. Any Suggestions?

After the recent update, my documents moved from Finder to Word. When I moved the folders to Finder, I am unable to attach a file to an e-mail. Any Suggestions?

Back up all data.
Triple-click the line of text below to select it, the copy the selected text to the Clipboard (command-C):
/Library/Internet Plug-ins
In the Finder, select
Go ▹ Go to Folder
from the menu bar, or press the key combination shift-command-G. Paste (command-V) into the text box that opens, then press return.
From the folder that opens, remove any items that have the letters “PDF” in the name. You may be prompted for your login password. Then quit and relaunch Safari, and test.
I've seen an unconfirmed report that the "Silverlight" web plugin distributed by Microsoft can also interfere with PDF display in Safari, so you might need to remove it as well, if applicable.
If you still have the issue, repeat with this line:
~/Library/Internet Plug-ins
If you don’t like the results of this procedure, restore the items from the backup you made before you started. Relaunch Safari again.

Unable to attach pictures to texts

Similar Messages

Maybe you are looking for