Unable to boot up my netbook with / win 7: error code: status 0xc000000f

Hi, 
I have a mini 110-1133nr netbook w/win 7. I brought the recovery disc from hp and I have to use an external drive to run the recovery disc.  The recovery disc wasn't able to run at all.  I had changed the boot sequence for the usb frist then hard drive.  But I had this error code: INFO the boot selection failed because a required device is inaccessible. status: 0xc000000f.  Need help.. Thank You in advance!

You have to set the PC to boot from the usb drive, with the drive connected and the first recovery disc inserted, power up the notebook and hit F9 repeatedly to get the advanced boot menu, select the external usb drive as the boot device and hit enter, see if recovery starts.

Similar Messages

  • Error "Unable to load word breaker for locale 0. Error code 8007007e." with search service application.

    I recreate the Search service application and the default Content source stayning in the 'Recovering' status.
    The log give multiple error 'Unable to load word breaker for locale 0. Error code 8007007e.'
    The default language is English and the reference in registry for word breaker dll is naturallanguage1.dll but I found only the naturallanguage6.dll.

    Hi,
    For your issue, check your current language settings and ensure that search supports the current language.
    On the SharePoint Server open Registry Editor (Start -> type “Regedit” and hit enter). 
    Point to : HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\OfficeServer\14.0\Search\Setup\ContentIndexCommon\LanguageResources\Default\English
    Under the registry key for each of the languages there is a value called StemmerDLLPath and WBDLLPathOverride
    Updated the registry entry with NATURA~1.dll to NATURA~2.dll
    Point to Start -> Administrative Tools -> Services, right click on SharePoint Server Search 14 and click on Restart.
    Performed a Full Crawl and wait for the Full Crawl to complete and try searching again.
    For more detailed information, refer to the following blogs:
    http://blog.ithinksharepoint.com/2008/04/20/a-word-breaker-was-not-found-for-the-given-language-error-when-crawling-content/
    http://www.sharepoint2013.me/Blog/Post/175/Word-breakers-in-SharePoint-2013
    Best Regards,
    Lisa Chen
    Lisa Chen
    TechNet Community Support

  • Unable to update itunes. help. error message when trying to update to latest version of itunes. "the installer has encountered an unexpected error installing this package. this may indicate a problem with this package. error code 2721"

    unable to update itunes. help. error message when trying to update to latest version of itunes. "the installer has encountered an unexpected error installing this package. this may indicate a problem with this package. error code 2721"

    Hello chae84swangin,
    I recommend following the steps in the article below when getting an error message trying to install iTunes:
    Trouble installing iTunes or QuickTime for Windows
    http://support.apple.com/kb/HT1926
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • I am trying to get the free trial to cc but it said there seems to be a problem with the files (Error code: 205)

    I am trying to get the free trial to cc but it said there seems to be a problem with the files (Error code: 205) please help

    BOILERPLATE TEXT:
    Note that this is boilerplate text.
    If you give complete and detailed information about your setup and the issue at hand,
    such as your platform (Mac or Win),
    exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
    your settings in Photoshop > Preference > Performance
    the type of file you were working on,
    machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
    what troubleshooting steps you have taken so far,
    what error message(s) you receive,
    if having issues opening raw files also the exact camera make and model that generated them,
    if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
    etc.,
    someone may be able to help you (not necessarily this poster, who is not a Windows user).
    a screen shot of your settings or of the image could be very helpful too.
    Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
    http://forums.adobe.com/thread/419981?tstart=0
    Thanks!

  • TS3694 I cant get my ipad 2 out of recovery. The apple icon stays on and nothing happens. I tried restoring it through Itunes but it comes up with a 3194 error code. I have the latest Itunes being 10.6.1.7 and the latest windows update.Can someone please

    I cant get my ipad 2 out of recovery. The apple icon stays on and nothing happens. I tried restoring it through Itunes but it comes up with a 3194 error code. I have the latest Itunes being 10.6.1.7 and the latest windows update.Can someone please help?

    Recovery Mode
    1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
    2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
    3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
    4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
    Note: Data will be lost. You may have to repeat the above many times.

  • After installing the most recent iTunes update/version iTunes will no longer run on my PC.  I receive a window with the Microsoft error code R6034

    After installing the most recent iTunes update/version iTunes will no longer run on my PC (Windows 7).  I receive multiple error windows with the Microsoft error code R6034.  Microsoft's Help site states that this error occurs when a driver attempts to access the C++ library without a "Manifest".  I do not know what a manifest is, but apparently any attempt to directly access the C++ library is not permitted.  The site instructs the viewer to contact the application developer.

    Try the following user tip:
    Troubleshooting issues with iTunes for Windows updates

  • Incompatible with Adobe InDesign (Error code: 14)

    Hi all,
    I've been having major problems with InDesign CS3 and OS 10.5. It always crashes when I try to Place, Export, Save As, anything that requires it to navigate the finder.
    Now, while trying to export to PDF, the document froze. So I had to force quit it. Now ANY InDesign file I try to open gives me the error message:
    The file "file name" is incompatible with Adobe InDesign (Error code: 14).
    Has anyone experienced this? I'm now stuck as I cannot open anything to get some work done.
    Thanks in advance.

    Hi all
    I have the excat same problem. Indesign CS5 and also my CS4 comes op with the error code 14.
    It qrashes before I get into the program, also when I open it throug the program Icon and not the file.
    I have tried:
    Restarting
    Shot down and take out the power cord for severeal minutes
    Deleting the preference files "Defaults" and "SavedData" manualy
    Deleting the file "InfoPlist.Strings" in folder "itlproj" which was a folder that keept showing on restart. (it was a italian languae to a dropdown shadow throug Flash CS5)
    Remove indesign CS5 and CS4 (with the program uninstall icon) and reinstalled it
    I have no clue to what more I can do. Think it could be a system fault. I have the following:
    Mac OS X Version 10.6.8
    Dual core Intel Xeron
    Snow leopard
    It just suddenly didnt work. Couldnt copy paste text from a mail into a file in Indesign and then it just crashed. Havent installed any new updates or programs so it is very weird.
    Any help would be very much appriciated
    Take care
    Fustrated Jinnie

  • Itunes sudden can't connect with itunes store, error code 11556

    Sudden can't connect with itues store, error code 11556

    Try these discussions...
    https://discussions.apple.com/message/18950811#18950811
    https://discussions.apple.com/message/20057934#20057934
    FRom the  More Like This  section on the right.

  • Unable to access or view data with no authorization error

    Hi Experts,
    Appreciate your guys help. I am ID administrator where by some of our user ID unable to view data/ display report for the some of data even the appropriate authorization already assigned to the user. However when we check in the transaction SU53 - authorization checking no error shown!
    There is a case whereby user report that his ID (e.g. SAP ID = ABC) unable to access a transaction or infotype data for example HR infotype masterdata,upon checking there is no authorazition error (checked insu53), when copy the ID (ABC) to another new ID (ABC1) with no changes on the roles, the ABC1 ID able to access the said transaction.However, when copy back ABC1 to the ABC (naming conversion only), the ABC ID still unable to access the transaction with no authorization error. the
    main problem here is the original ID is not working, but works fine if it is copied to another ID name.
    Kindly advice.

    Hi Manikya Raju,
    Can you explain details?

  • Hp pavilion elite m9340 will not boot from hd or cd. i get error code biohd-3.

    Like title says, box won't boot from HD nor from recovery disk, OS- Windows7. BIOS and system diagnostics recognize both drives. I opened the box and unplugged HD SATA cable and was able to boot it from recovery disk. It seems as though something is wrong with HD that won't let system boot correctly. Any help is greatly appreciated. Mike.

    Hi,
    The error code that you are getting normally indicates a bad hard drive. Be sure that the power connector for the hard drive is on tight.  Plug the HD into a different SATA port and see if the same issue occurs. If it does, then you have a bad hard drive.  You might need to hit the ESC key at the HP splash screen to pick the boot device since you moved the cable if you get that far.
    A new 3.5" SATA hard drive under 2 TB should work just fine.
    HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
    HP Photosmart Premium C309G, HP Photosmart 6520
    HP Touchpad, HP Chromebook 11
    Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
    Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
    Windows 7/8 UEFI/Legacy mode, MBR/GPT

  • Unable to read data from Analog Devices 6b11 module - error code 1240

    Hi everyone,
    I'm trying to read data from a thermocouple with an AD 6B11 module in an AD 6BP16-1 backplane using RS232 serial. I've been following this guide:
    http://digital.ni.com/public.nsf/allkb/8C77E5E52B4A27968625611600559421
    Everything seems to work out well until step 13, where I call the "AD6B Input Module - Read Data.VI". I get an error code 1240 stating something like "invalid parameter or unable to read instrument".
    Has anyone got any experience with this error or suggestions to fixing it?
    Thanks in advance!

    That user guide is 20+ years old. The serial functions from that day used 0 for com 1, 1 for com 2, etc. Make sure you have the correct one selected. Please provide the exact error message instead of 'something like'.

  • FLIR A2600SC IR camera connection problems with NI-Vision - error code 0xBFF69011

    Hi, hopefully someone can help me out with a connection problem I’m having with a FLIR A2600SC IR camera:
    The camera is detected by NI-IMAQdx in MAX but when clicking on the camera (to browse) it just comes back with error code 0xBFF69011 “Unable to get attribute”. Reading through the Forums, there is a file: “SC2600_1_0_0_8FC7DBB4.xml” which tells MAX what attributes to ask for but the files has quite a few lines and trying to figure out which line is causing the problem seems to be a daunting task.
    I used the Camera Validator Utility that ships with NI-IMAQdx and it detects the camera just fine but it also comes back with an error: 0xBFF69012 “Attribute value is out of range”. These two errors lead me to believe that I need an updated (xml) file for this camera. Any ideas of where I might get it?
    All FLIR drivers and software packages are installed and their software works just fine with no issues.  LabVIEW and NI-Vision software are updated to the latest available and are running on a Win7 (x64) machine.
    Any help or comments will be appreciated!

    Kozby,
    The "PacketSize" value is located in the "devicename.xml" file that MAX loads up when initializing the device. Search in "c:\Program Files\National Instruments\MAX\Assistants\"USB device name"; normally it has the same name as displayed in the device tree under MAX. Use an xml editor or NotePad++ when changing values in the file; XML syntax applies.
    When MAX detected your USB device and loaded it, it created a folder for the device in its directory, and saved all the necessary files needed to access said device. So, look at all the xml files in that folder and one of them will have the parameters.
    The way I figured out which parameter was causing the issue, was by comenting out the configuration parameter that I tought most likely to be the culprit and running the device to see if the problem went away. Once I pinpointed the offending parameter then continued by changing its value until I got the device to work properly. For me the "PacketSize" was the culprit because it was set to a size not allowed by the IR camera. MAX was expecting/requesting a packet size (video grab) bigger than what the camera could grab/send and MAX or the IR camera was erroring out. Also, look at the documentation for your device and find the packet size it send during TCP/IP communications (for my IR camera it was 1408).
    Make sure to use xml syntax. To comment out a line in an xml file use "<!--  "parameter data"  -->" where "parameter data" is the line you are commenting out.
    Best regards,
    Opus20
     

  • Synchronization errors with AD: LDAP error code 65 : orclObjectSid

    I'm trying to get synchronization working - importing data from Microsoft AD.
    The bootstrap seemed to go ok, and the synchronization is up and running - but I still get errors in the profile's trace file as follows at the end of this post.
    The error always seem to complain about the orclObjectSid attribute
    Do I need to do anything to the OID schema?
    Or is this a mapping problem?
    Either way, how would I correct this error?
    Thanks!!
    Howard Dickins
    Here's an example of the errors I'm getting:
    DN : dc=connectutilities,dc=co,dc=uk
    Normalized DN : dc=connectutilities,dc=co,dc=uk
    Processing modifyRadd Operation ..
    Proceeding with checkNReplace..
    Performing checkNReplace..
    Naming attribute: dc
    Naming attribute value: dc
    Naming attribute value: orclObjectSID
    Adding Attribute in OID : orclObjectSID
    Naming attribute value: orclobjectguid
    Adding Attribute in OID : orclobjectguid
    Total # of Mod Items : 2
    Exception Modifying Entry : javax.naming.directory.SchemaViolationException: [LDAP: error code 65 - Failed to find orclobjectsid in mandatory or optional attribute list.]; remaining name 'dc=connectutilities,dc=co,dc=uk'
    javax.naming.directory.SchemaViolationException: [LDAP: error code 65 - Failed to find orclobjectsid in mandatory or optional attribute list.]; remaining name 'dc=connectutilities,dc=co,dc=uk'
         at com.sun.jndi.ldap.LdapCtx.mapErrorCode(LdapCtx.java:3019)
         at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2934)
         at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2740)
         at com.sun.jndi.ldap.LdapCtx.c_modifyAttributes(LdapCtx.java:1440)
         at com.sun.jndi.toolkit.ctx.ComponentDirContext.p_modifyAttributes(ComponentDirContext.java:255)
         at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.modifyAttributes(PartialCompositeDirContext.java:172)
         at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.modifyAttributes(PartialCompositeDirContext.java:161)
         at javax.naming.directory.InitialDirContext.modifyAttributes(InitialDirContext.java:146)
         at oracle.ldap.odip.gsi.LDAPWriter.checkNReplace(LDAPWriter.java:839)
         at oracle.ldap.odip.gsi.LDAPWriter.modifyRadd(LDAPWriter.java:717)
         at oracle.ldap.odip.gsi.LDAPWriter.writeChanges(LDAPWriter.java:310)
         at oracle.ldap.odip.engine.AgentThread.mapExecute(AgentThread.java:581)
         at oracle.ldap.odip.engine.AgentThread.execMapping(AgentThread.java:306)
         at oracle.ldap.odip.engine.AgentThread.run(AgentThread.java:186)
    [LDAP: error code 65 - Failed to find orclobjectsid in mandatory or optional attribute list.]
    Entry Not Found. Converting to an ADD op..
    Processing Insert Operation ..
    Performing createEntry..
    Exception creating Entry : javax.naming.directory.SchemaViolationException: [LDAP: error code 65 - Failed to find orclobjectsid in mandatory or optional attribute list.]; remaining name 'dc=connectutilities,dc=co,dc=uk'
    [LDAP: error code 65 - Failed to find orclobjectsid in mandatory or optional attribute list.]
    javax.naming.directory.SchemaViolationException: [LDAP: error code 65 - Failed to find orclobjectsid in mandatory or optional attribute list.]; remaining name 'dc=connectutilities,dc=co,dc=uk'
         at com.sun.jndi.ldap.LdapCtx.mapErrorCode(LdapCtx.java:3019)
         at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2934)
         at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2740)
         at com.sun.jndi.ldap.LdapCtx.c_createSubcontext(LdapCtx.java:777)
         at com.sun.jndi.toolkit.ctx.ComponentDirContext.p_createSubcontext(ComponentDirContext.java:319)
         at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.createSubcontext(PartialCompositeDirContext.java:248)
         at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.createSubcontext(PartialCompositeDirContext.java:236)
         at javax.naming.directory.InitialDirContext.createSubcontext(InitialDirContext.java:176)
         at oracle.ldap.odip.gsi.LDAPWriter.createEntry(LDAPWriter.java:1031)
         at oracle.ldap.odip.gsi.LDAPWriter.insert(LDAPWriter.java:386)
         at oracle.ldap.odip.gsi.LDAPWriter.modifyRadd(LDAPWriter.java:725)
         at oracle.ldap.odip.gsi.LDAPWriter.writeChanges(LDAPWriter.java:310)
         at oracle.ldap.odip.engine.AgentThread.mapExecute(AgentThread.java:581)
         at oracle.ldap.odip.engine.AgentThread.execMapping(AgentThread.java:306)
         at oracle.ldap.odip.engine.AgentThread.run(AgentThread.java:186)
    DIP_LDAPWRITER_ERROR_CREATE
    Error in executing mapping DIP_LDAPWRITER_ERROR_CREATE
    DIP_LDAPWRITER_ERROR_CREATE
         at oracle.ldap.odip.engine.AgentThread.mapExecute(AgentThread.java:722)
         at oracle.ldap.odip.engine.AgentThread.execMapping(AgentThread.java:306)
         at oracle.ldap.odip.engine.AgentThread.run(AgentThread.java:186)
    DIP_LDAPWRITER_ERROR_CREATE
    AD_OID_Import:Error in Mapping EngineDIP_LDAPWRITER_ERROR_CREATE
    DIP_LDAPWRITER_ERROR_CREATE
         at oracle.ldap.odip.engine.AgentThread.mapExecute(AgentThread.java:741)
         at oracle.ldap.odip.engine.AgentThread.execMapping(AgentThread.java:306)
         at oracle.ldap.odip.engine.AgentThread.run(AgentThread.java:186)
    AD_OID_Import:about to Update exec status
    Updated Attributes
    orclodipLastExecutionTime: 20090617062658
    orclodipConDirLastAppliedChgNum: 12242192
    orclOdipSynchronizationStatus: Mapping Failure, Agent Execution Not Attempted
    orclOdipSynchronizationErrors:
    Sleeping for 1secs
    LDAP URL : (inexus-srv01:389 oracleextract
    Specifying binary attributes: mpegvideo objectguid objectsid guid usercertificate orclodipcondirlastappliedchgnum
    LDAP Connection success
    Applied ChangeNum : 12242192Available chg num = 12245972
    Reader Initialised !!
    LDAP URL : (inexus-srv34:389 cn=odisrv+orclhostname=inexus-srv34,cn=registered instances,cn=directory integration platform,cn=products,cn=oraclecontext
    Specifying binary attributes: mpegvideo objectguid objectsid guid usercertificate orclodipcondirlastappliedchgnum
    LDAP Connection success
    Writer Initialised!!
    Writer proxy connection initialised!!
    MapEngine Initialised!!
    Filter Initialised!!
    searchF :
    CHGLOGFILTER : (&(USNChanged>=12242193)(USNChanged<=12242692))
    Search Time 0
    Search Successful till # 12242692
    Search Changes Done
    Changenumber uSNChanged: 12242193
    targetdn distinguishedName: DC=connectutilities,DC=co,DC=uk
    ChangeRecord : ----------
    Changetype: ADDRMODIFY
    ChangeKey: dc=connectutilities,dc=co,dc=uk
    Attributes:
    Class: null Name: objectGUID Type: null ChgType: REPLACE Value: [[B@1c999c4]
    Class: null Name: objectSid Type: null ChgType: REPLACE Value: [[B@8e5360]
    Class: null Name: dc Type: null ChgType: REPLACE Value: [connectutilities]
    Class: null Name: objectClass Type: nonbinary ChgType: REPLACE Value: [top, domain, domainDNS]
    -----------

    I found a solution - I added the offending attribute orclObjectSid to the domain objectClass as an optional attribute.
    It was a bit of a "clutching at straws" solution - but it does seem to have worked.
    I'm not sure why the data being imported had such a value, but the synchronization hasn't thrown up any further errors since then.
    Thanks for your help everyone.
    Howard

  • Windows 2008 R2 backup fails with event 521 error code 2155348001

    Windows Server 2008 R2 SP1.  Hyper-V role installed. 
    OS on drive C.  All VMs stored on Drive D.
    I am attempting to run a Bare Metal backup of the host system to a network share. 
    Drive D is not included in the backup job.  I am getting the following error:
    Log Name:      Application
    Source:        Microsoft-Windows-Backup
    Date:          1/10/2014 11:28:52 PM
    Event ID:      521
    Task Category: None
    Level:         Error
    Keywords:     
    User:          SYSTEM
    Computer:      SHAQTUS.scdl.local
    Description:
    The backup operation that started at '‎2014‎-‎01‎-‎11T04:08:50.683000000Z' has failed because the Volume Shadow Copy Service operation to create a shadow copy of the volumes being backed up failed with following error code '2155348001'. Please review the event
    details for a solution, and then rerun the backup operation once the issue is resolved.
    Reviewing event details, as suggested, does not offer any solution.
    I have tried the suggested solutions in other similar threads of increasing the timeout value with the registry entry. 
    This does not work.
    I have not tried reregistering the VSS writers manually, as the only links I have found are for server 2003/2008 (not R2) and explicitly state that they won’t work on higher versions of the OS, since they now utilize manifests and the manual procedure could
    cause problems for those servers. Haven't found similar procedures for 2008 R2.
    I have been able to narrow this down a bit.
    A Windows 2008 R2 SP1 server with Hyper-V installed – backup to a network share is successful;
    Install the DPM 2012 agent – same backup fails with the 2155348001 error.
    We use DPM 2012 to backup VMs, but DPM cannot perform a bare metal backup/restore of server and the 2012 version no longer has the DPMSRT feature. 
    I prefer to run Bare Metal Backup to a file server share.
    Stuck on this one.
    Rick

    Hi, 
    The issue is related to DPM, I would suggest you ask for help from DPM forums:
    http://social.technet.microsoft.com/Forums/en-US/home?forum=dataprotectionmanager
    Regards, 
    Mandy
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • TS3694 hi, i tried to do a software update on my iphone 3gs and it comes up with an unknown error code 1015, any ideas?

    i tried to do a software update on my iphone 3gs comes up with an unknown error message code 1015
    any ideas?

    See this post:
    TS3694 Trying to restore and update my iphone 3, the system tells me 1015 error What can I do?

Maybe you are looking for