Unable to capture Canon HDV footage with Sony v1u camera

I'm trying to capture hdv footage filmed with a canon video camera with my sony v1u. My sony footage captures as it should, but the canon footage, although playing fine on the sony camera, will not capture to cs4. Any suggestions?

Check all camera settings and make sure they match the original filming mode on the other camera... and veryify your PPro settings match
If that doesn't work, try http://strony.aster.pl/paviko/hdvsplit.htm

Similar Messages

Trouble capturing HDV footage from Sony Z5U in FCE4 - any ideas?

I've shot about half an hour of HDV footage with the Sony Z5U. Have the computer at home connected to my Mac with a firewire. Tried with both firewires that I own. I've used a similar camera before to capture footage recently with no problems.
Gone through the Easy Setup in FCE4 and changed it to HD, HDV1080i60. In the camera, the VCR mode is set for HDV, the Video Out for Component says "1080i/480i", the down convert and DV wide convert are for letter box.
Any ideas on what the problem is? Do I just have 2 bad Firewire cables? or a bad port on my computer/camera?

Do you want to downconvert, or do you want to capture HD? Switch off downconvert. Switch off iLink.

Editing footage with sony HXR-MC50E what cable or program do I need to transfer

Editing footage with sony HXR-MC50E what cable or program do I need to transfer footage to computer and into Final Cut Pro?
I am editing with Final Cut Pro
I have a Mac
My footage is on the HXR-MC50E

One small correction-- you do not use File-->Import. You must use Log and Transfer in FCP 7 or Import From Camera/Import Media in FCP X. In FCP 7 the clips will be automatically converted to ProRes upon import. In FCP X you can choose to work with the native files (re-wrapped to .mov) or you can optionally transcode to ProRes. When importing in FCP X, enable the 'create optimized media files' option to convert to ProRes. If you do not enable this option the files will remain in their native codec.

Unable to print to video, out to Sony V1U

Wedding video shot with Sony V1U, HDV 1080i 16x9. Imported into FCEHD3.5, using easy set up hdv 1080 AIC. total movie length 100minutes. Edited fine. Exported as a QT movie self contained to desk top, no problem. Then attempted to export from the time line the entire sequence. The FCE is pretty easy to export from and set the sony v1u to HDV import with both auto and HDV settings. It is in VTR mode. I checked the render again and it was complete. saved the project. Closed FCEHD. connected fire wire from cam to computer and powered up cam with what appear to be the correct setting according to the manual. Opened FCEHD and project. Rechecked render, resaved project and chose print to video. Went through the next screen as I normally do and have tried with both automatic record start and manual record start. Clicked start and the computer does its job and the video starts but the camera does not appear to ever be controlled by the computer. I let it run for about 30 minutes to see if it needed time to change from Mpeg2 back to HDV. Maybe I did not wait long enough for the number crunching before I gave up.
Question 1: What am I doing wrong.
I tried to export a SD movie and it worked fine.
I tried to send it to IDVD from the QTmovie.fcp file on the desk top but it immediately shuts down IDVD. I tried to import into ImovieHD and it gave me a QT error. I thought maybe imovie had a time limit so I re-exported the movie in to sections as FCP and then dragged and dropped into imovie and it worked. The resolution is much worse in imovie as compared to the great video in FCEHD.
Question 2: Am I losing quality as I move from HDV to FCEHD ( I would assume so as it is going to Mpeg2), and even more when I go then from FCEHD to imovie.
Question 3: When I print to tape from fce back to my original hdv setting it should convert back to hdv correct?
Any advide would be appreciated.
Thanks, Steve

Purchased IDVD8 and problem solved

How do i open a photo taken with sony p1 camera saved in dsc format on cd?

How do i open a photo taken with sony P1 camera saved in DSC format on a CD?

The P1 looks like a high end video camera not a still photo camera to me and DSC files appear to be support files not photo or movie files
Why do you think that you have photos in a DSC format?
You might give Google a shot and see what you can find but it looks to me like you do not have either image or video files but supporting files - and if you have video files you may have to use iMovie - it is much more robust at working with videos
LN

MAC and FINAL CUT NOT RECOGNIZING SONY V1U Camera

The new Sony V1U camera (out this year) is not being recognized by my iMAC computer (this years latest model) and nor by the FINAL CUT PRO HD 5.1 ...Any suggestions?
I already called Mac/ Final Cut - they had the other models (Sony A1U and Z1U)listed as compatible with FC, but the V1U wasn't listed - I'm thinking since it's brand new, it's just not listed yet. We tried at Samy's camera to get it to work with their MAC/ FC but no go, and I tried different fire wire cable- wasn't the problem either. ANy help is appreciated - Do I need a Sony Driver or will I just have no luck hooking up the camera?

Just got the new HVR-V1U and it worked correctly out of the box with FCP 5.1.2 and iMovie HD on a Mac G5 Quad. IMovie saw the camera correctly right away as HD and captured that way; I set FCP to HDV 1080i60 and it captured correctly.
The camera setting for IN/OUT REC are:
REC FORMAT: HDV 1080i
COMPONENT: 1080i/480i (it auto switches depending on what's on tape)
i.LINK CONV: OFF
DOWN CONVERT: SQUEEZE (nothing happens since iLink convert is off anyway).
Note that the camera does NOT capture in Quicktime "New Movie Recording" unless I put it into DV mode or downconvert mode, but in any of those DV modes, the picture is squeezed regardless of my "squeeze, letterbox, or crop" selections.
The V1U will also capture to FCP and iMovie while just in camera mode: no tape recording, but just whatever the camera is looking at. Sounds like tapeless recording is possible, though there must be a tape in the machine. I haven't tried the HDMI through a BlackMagic Intensity (because I don't have one, and it doesn't work yet with G5's in any case), so I can't comment on the cameras raw performance. Camcorderinfo.com has a detailed review of the FX7 which has similar, if not identical video properties in the default modes.
I did some quicky video recording tests in HDV and captured them on FCP as HDV, then as camera downconverted DV (anamorphic). I then used compressor to convert each of those streams to mpeg2 (4.5 avg, 7.5 max) and the HDV to mpeg2 direct is slightly better, especially in vertical red bleed.
My only grip so far is that Sony did not include a regular mini-stereo microphone plug in, but only the XLR pair. For serious video work, you probably do want to use XLR mics; but it sure would be nice to be able to just plug in my cheapy Sony ECM-MSD1 to do casual recording in stereo instead of recording only mono with the included mic. Oh, well, we can't have everything, can we.
Ed

Unable to capture HDV footage with FCP 5.1

I've captured HD footage onto my old computer (10.4.11) without any problem but now I'm trying on my new one and it doesn't want to know.
First off there was a problem with the Firewire port ejecting my hard drives randomly so I took it to be repaired and they replaced the logic board and the port works fine.
I've looked at all the posts I could find, I've trashed my preferences, reinstalled Final Cut Studio ( after uninstalling then updating the software). I've made sure the camera is set to HDV playback rather than auto and that the iLink HDV/DV conversion is off. I've tried all the easy setups and all the custom ones I could think of but still FCP (5.1.4) won't allow me to capture. On some settings I have had device control but no image, on others it said the camera isn't connected. The only way I've captured footage is by using the HDV Apple Intermediate Codec 1080i50 which works fine.
The camera is a Sony HDR-HC7 connected directly to the iMac with a Firewire 800 / iLink cable or daisy chained through my external hard drive with a 400 / iLink cable (neither of which makes any difference) I can also capture SD footage from both the HDV and a Panasonic SD camera when in DV-PAL setup. The HDV camera also shows up as connected in the system profiler.
This is driving me nuts so any help would be appreciated and if there's any other info I can help with to make this clearer let me know.
Message was edited by: MrMajesticMole

I just got off the phone with a friend of mine who was having the same problem as you. Although you say the camera playback is set properly, please recheck this. go into your camera's playback menu>menu>standard set>VCR HDV/DV. Unplug your firewire from the camera. Make sure camera is set to HDV NOT auto. replace firewire cable. Now open FCP. Go in Audio/video settings>A/V devices (farthest tab on right). In box for playback edit to tape different from video output (make sure it's checked) mirrored (checked) Video playback 1080i50, Audio HDV. I hope that works now.
Steve

Capturing HDV 1080i50 with Sony HVR-Z1U

Long winded question... hope someone can offer some insight.
The answer to this may have been posted earlier, but sifting through the topics, I couldn't find any relating. If someone could be so kind to link me to any related topics, that would be helpful.
I'm editing a project in Final Cut Pro 5.0.4 that is a mix of HDV and DV, but will be finishing the final product in HDV. I've edited the original project in regular DV, but am batch capturing in the HDV footage according my XML.
But I can't seem to connect the camera.
Easy Setup: HDV - 1080i50 gives me an error "Unable to locate the following external devices: HDV (1440 x 1080) 2 fps)"
Going into Audio/Visual Settings and setting Capture settings to HDV and Device control preset to HDV Firewire gives me an error "Unable to initialize capture device and device control" (or for any device control preset with the HDV Capture setting for that matter)
Any device control preset with "HDV - Apple intermediate codec" will give me an error with "Unable to initialize HDV deck. Please make sure a deck is connected and try again".
Camera: In/Out VCR mode is set to Auto, i.Link Converter is set to "Off", A/V->DV Out is set to on.
Camera is on and plugged in. I've tried plugging the firewire into different ports and have also tried various firewire cables. Sometimes the device is controllable, but all it does is play the tape, never gets around to capturing anything.
.... sigh....
Thanks in advance,
_tess
Power PC G5 (iMac) Mac OS X (10.4.4)

AIC is not going to work for recapture, AIC doesn't use the original timecode off the master tape. Make sure you setup HDV 50i and before connecting the firewire cables go into the camera vtr mode then menu, then rec in out and set the ilink convert to off for HDV. the Camera will show HDV lights. Then connect to the computer and open log and capture.
Good Luck
Z1&V1user

Problems with HDV footage from sony HDR - HC9

I have a new sony HDR-HC9 cam corder. I want to shoot in hi def (HDV) format for best quality, but I produce standard def DVDs as a finished product. I was hoping to use the built in iLink conversion from HDV to DV when downloading to the computer into iMovie. I have had many problems with this.
Usually, when I set it up to do the downconversion, I see a blue screen in iMovie, although iMovie will ff and rew the camera, no images come across. I experimented with setting the camera in DV record mode at the same time as I had the iLink down conversion set, and this appeared to work. I started downloading an hour tape, and when I came back 65minutes later (after it should have been done), saw the message that iMovie had quit. Reopened the project, and saw an hour worth of footage in the trash, but it was too crazy to reorder the clips from the trash back to the clips pane.
I resigned to import in hdv (1080i) format and not mess with hardware downconversion. This worked fine. I then added some chapter markers and shared the project with iDVD. I saved the project as an image file and then mounted it to check it for errors. The video was OK, but towards the end of the project, the sound was out of sync by a few seconds with the video.
I deleted encoded assets from the iDVD project, then reburned (save as image file). Same defect.
I then started a new iMovie project in standard DV widescreen, and dragged all of the clips from the HDV (1080i) project into the time line. It took over an hour for my mac mini to run the conversion, but the movie in iMovie appeared OK. I redid the iDVD project, and saved as image file. It appears to have worked correctly (although I have not looked at it on my widescreen TV yet to assess image quality.
Questions:
1) Has anyone had any luck getting HDR-HC9 iLink HDV-DV hardware conversion to work with iMovie, consistently?
2) Can anyone comment on image quality issues with converting HDV to DV footage using iMovie software.
3) Has anyone seen audio sync problems with iDVD from HDV original footage.
Thanks

Hi - you may get a more exact answer in the BlackMagic Macintosh forum, since there aren't a lot of BlackMagic queries on the Apple Discussions forums:
http://forum.blackmagicdesign.com/viewforum.php?f=11

Log and capture with Sony A1U camera, Sony HD700 HDV deck

Hello,
I am still having problems capturing HDV from a Sony GV HD700.
It sees the deck, can capture some, but then crashes. Anybody have experience
with certain decks and cameras not able to capture with Final cut 7?
I am stumped. Settings are HDV.....1080I 60 ... on presents.
thanks

[Read this|http://documentation.apple.com/en/finalcutpro/professionalformatsandworkfl ows/#chapter=2%26section=0] to make sure that you are doing everything right.

FCP unable to Capture Canon GL2

Hello -
My system is noted below. Final Cut Pro is updated to 6.0.4.
I am unable to capture the video using Canon's GL2 using the current version of FCP. I believe that I have everything configured correctly because I am able to capture audio and video using my father's JVC GR-DV800U video camera. Actually that particular JVC camera seems to work quite well with FCP. But not Canon's GL2. I am able to control camera's Rewind, Fast Forward, Play, etc. So I know that some communication is taking place. However, no picture is present within FCP; no capture either. Instead, I get that dreaded beach ball wheel.
I believe the FCP settings are correct: Under "Audio/Video" settings, the audio is set to MOTU's 424 (for the 2408 MK3); the DV Capture Preset (and the Sequence) is set to "DV NTSC 48 khz"; Video Playback is set for"Digital Cinema Desktop Preview - Main" with the audio playback set (again) to MOTU's 424 card.
I am attempting to capture the video to an external hard disk drive using the Mac Pro's firewire port located in the back of the computer. Again, this all works using my father's JVC video recorder.
*Given the computer setting and operating system, is this a known issue between the FCP and the GL2??* My GL2 is an older video camera. I purchased it quite a few years ago. *It seems like the GL2 may be the culprit. Yes? No?*
I'm very new to FCP. My background is with SONY's Vegas program (currently I'm up to version 8). Been using the Vegas program for years. My Dell Workstation, unfortunately, is old; it definitely is showing signs of aging. So, to make a long story short, I've decided to invest time and money in a Mac Pro (I use it primarily for music sequencing using the Logic Pro program which I love!) Now I want to learn how to use the FCP which I purchased several months ago. Not being able to have FCP communicate with the GL2 is a minor significance for me, though. I'm in no financial place to purchase a new camera at this time. Luckily, I usually record the video using Focus Enhancement's FS4-Pro with the GL2. So I am not totally dependent on having FCP and the GL2 work together. *Thankfully, the FS4-Pro DOES works well with FCP!!* Too bad I didn't use the FS4-Pro today. Wish I did. UGH
Could there be a work around in getting the GL2 to communicate properly with FCP??
Thank you in advance for your thoughtful insights and suggestions.
Regards,
Ted Fiebke

Not all Canon cameras have connection issues, but hanging around this site I've come to recognize their ability to connect in FCP is the most problematic of all the camera brands. If you have a Canon camcorder, and can not get it to connect up with FCP, the following is a way to sort through the issues and get it to work. Some are elegant - some are ugly.
Before we go any farther
• You should be using 'Firewire Basic' as the control protocol. If you aren't, go change it and try again.
• Also, verify that you have a solid installation of Quicktime. You may want to reinstall it using the 'delete receipts' method.
With some confidence that the software installation and camera settings are correct ... the most direct solution is to purchase another, non-Canon device to use as your capturing machine. The (now discontinued) Sony DSR-11 is highly recommended for DV work. A deck will save wear and tear on the camera's lightweight drive mechanism and will allow you to permanently connect a NTSC/PAL monitor for proper viewing. If you are working with HDV, you may have other issues ...
Beyond that, the path you take depends on the model of computer you own.
1. If you have a G5 tower or a MacPro, capture to a second internal drive with only the camera attached. If you need to move material to firewire drive, disconnect the camera. A second internal drive is quite inexpensive these days if you do not already have one.
2. If you have a G5 tower (PCI) MacPro (PCI), G4 powerbook (PCMCIA) or MacBookPro (Expresscard 43) with an available slot, purchase the appropriate firewire card for the slot. Connect your camera to the card and you should be good to go. The new card creates a unique bus and will avoid collisions with the external drives.
3. If you do not have a slot or a second internal drive and you are stuck with the camera, welcome to the camera/drive shuffle.
• shut down and remove the external hard drive(s) from the system
• connect the camera directly to the firewire port of the computer
• start the camera then the computer
• capture to your internal (system) hard drive
• shut down the camera and computer
• disconnect the camera and reconnect the external hard drive(s)
• start hard drive(s) and computer
• move captured files to external hard drive(s)
• edit
If you output back to tape or wish to view your work on an external Video (NTSC or PAL) monitor, you need to set up the camera to use the firewire out as the A/DV converter or VTR - which means reversing the steps:
• copy the file back to the internal drive
• shut everything down
• disconnect the external drive(s)
• connect the camera to the firewire port (and the TV to the camera if needed)
• start the camera then the computer
• play the file.
One caveat here - You may have difficulty getting the file back to tape without dropping frames. Playing files off of the system drive is very demanding and they may have a hard time keeping up.
All in all, if you do not have the option for second bus (i.e. iMacs, eMacs, iBooks, MacBooks) you may want to think about a computer with expandable options next time.
There is the option of capturing using iMovie, but that brings on it's own set of problems and is not recommended.
Good luck.
x

Unable to Capture PAL DV footage

I'm working on a project that requires I edit with both PAL and NTSC footage shot on mini-DV. I was about to purchase a plug-in to convert the PAL footage to NTSC, but find that I can't even capture the PAL footage to begin with.
I tried using both a deck and a camera as the source device to capture from and they both play the tape just fine and on the camera's LCD (not a PAL camera by the way), I can view the footage perfectly, but still FCP does not acknowledge any video on the tapes.
I've even tried capturing on iMovie-it tells me that the footage can't be captured because it is 'half-frames' and mentions LP and SP modes. Would this really matter and why does my camera play it just fine?
Also, when I play the tape on the camera and plug-in to a television, the picture keeps rolling, but again, plays perfectly on my non-pal camera.
I've tried switching all pre-sets to PAL, but it doesn't help.
I'm about to make a dub tape with a PAL camera (Sony Z1U) and see what happens, but if anyone has any other suggestions, I'd really appreciate any help.
Thanks.

I tried using both a deck and a camera as the source device to capture from and they both play the tape just fine and on the camera's LCD (not a PAL camera by the way), I can view the footage perfectly, but still FCP does not acknowledge any video on the tapes.
I have never seen an NTSC camera that plays PAL tapes!
Alberto

Digitizing HDV footage with a Consumer Grade HD Camcorder

I have HDV footage on mini-digital tape. I need to digitize using Final Cut Pro. I shot the footage using a Sony HVR-V1U camera at 24p (an HDV camera and recorded onto mini-digital tape. I no longer have convenient access to the Sony HDV camera and was wondering if I can simply use a consumer grade high-definition camcorder to digitize the footage into my computer. If so, is there any quality degradation?

I have HDV footage on mini-digital tape. I need to digitize using Final Cut Pro. I shot the footage using a Sony HVR-V1U camera at 24p (an HDV camera and recorded onto mini-digital tape. I no longer have convenient access to the Sony HDV camera and was wondering if I can simply use a consumer grade high-definition camcorder to digitize the footage into my computer. If so, is there any quality degradation?

Matching IPhone 4 Footage With Sony Ex1 On Timeline?

So just like title says I'm shooting a prank comedy show using the Sony Ex1 camera as master with several Iphone 4's (not the new 4os) as reaction shots and I was wondering what was the best way to set up my sequence or have the footage be the same so I dont have to render after every edit. Shoud I make all the footage Apple Pro Res through MPG Streamclip or whats my best option? Thanks for reading.

If you open the clip in fcp and hit command-9 you'll call up the clip settings. Look under field dominance and if the settings is "none" it's probably progressive, otherwise interlaced.
Usually combining progressive and interlaced in the timeline will not require rendering to at least view. But I'm not sure. Should be an easy enuf test to run.
I'd use compressor to convert the footage, but running tests on your workflow is crucial in this kind of project. The frames control pane in compressor has controls for scaling that can make a big difference in quality. Remember, you can set ins and outs in the preview window in compressor to do a test on a small section of a clip. You can also customize and save presets as you do tests.

Cannot capture HDV through my SONY Z1P camera

Hi all,
My system profiler can find my camera connected via firewire. Cannot see in my setting 1080i50i, only 1080i60i as a capture setting. I can get the camera to connect and read timecode but no vision until i downgrade in camera to convert output to DV. How do i go about capturing HDV on this model camera, many thanks.

i'm guessing you're just missing the setup, not the codec
open the Final Cut Pro menu > Audio/Video Settings... window
from the Sequnece Preset popup choose: HDV - 1080i50
from the Capture Preset popup choose: HDV
from the Device Control Preset choose: Sony HDV 1080i50 Firewire
from the Video Playback popup menu choose: None
from the Audio Playback popup menu choose: Default
then press the Create Easy Setup... button
give your setup a Name (HDV - 1080i50) and Description (blah blah blah)
press Create... lastly, choose a filename for the preset, and save it to the default location

Unable to capture Canon HDV footage with Sony v1u camera

Similar Messages

Maybe you are looking for