Unable to capture video from canon xha1s to final cut pro 6.0. so confused

hi,
i purchased a canon xha1s and am simply trying to capture the video onto my macbook pro laptop. i keep getting the error saying my settings are incorrect and am confused as what to put and where. i went to the video/audio settings and put what i believed to be correct (HDV) since my camcorder records in HDV. still that error window pops up when i try to log and capture footage.
any help would be greatly appreciated!

Hi .. I had a very similar problem .. if the above fails it may be worth a look at this too..
http://discussions.apple.com/message.jspa?messageID=10804559#10804559
Jim

Similar Messages

  • Can you help me, i try to import video from my gopro to final cut pro but when i play the video he become very slow and i lose qualiter

    can you help me, i try to import video from my gopro to final cut pro but when i play the video he become very slow and i lose qualiter ???

    Right click one of yur clips in the event browser and choose Transcode Media. Make a test project and playthat clip. See whether that solves your lag.
    Russ

  • Capturing Footage from Canon HV40 to Final Cut Express Issue

    I own a Canon HV40 camcorder and shot a short film using the 24p HDV 24F Cine Mode feature (for film look). I've captured the footage into Final Cut Express, but the footage is running at a faster speed. I know this may have something to do with frames per second in the user preferences section.
    Does anyone have the concrete solution to this problem and will I have to recapture my footage under a different setting?
    Please advise.
    Thank you!
    - Eric

    Hi Eric,
    FCE only supports frame rates of 60i, 30p, 50i, and 25p. To edit 24p footage you'd need Final Cut Pro.

  • Unable to capture video from VHS through DAC-200

    (Running Final Cut Pro 5.1.4)
    I have a DAC-200 to hook up my VCR to my G5 in order to capture video from VHS tapes into Final Cut. I had this set-up working a few months ago, but it was disconnected to rearrange equipment and now I can't get it working again. I have followed the advice from the DAC-200 installation instructions and advice from other forum topics but can't seem to get it to work. I finally was able to get something in the log and capture window besides "preview disabled" and "cannot capture because there is no video." I now can get Final Cut to capture video, however it only captures a blank black screen (and this is all I can see in the preview window).
    I've triple-checked every cable hook-up, the G5 recognizes the converter box, the video tape plays fine to a tv. I've even had our IT-guy here at work come check out my set-up for help and he can't figure out what is wrong either. (He did get my log&capture window to get white fuzz in the black screen at one point though. Does that mean anything?)
    Any help is greatly appreciated! (I'm happy to answer any other questions too.) Thanks!

    I had difficullty with the X.4.10 plus QT7.2 and put my info on the Forum as well as sending feedback to Apple. Shortly afterwards, Apple brought out a short security update which I downloaded and, hey presto, I was then able to use QT7.2 with OSX.4.10. It may be that you missed out on the later small update to QT7.2..... ? Another factor I found was that some little while later I again had a problem so I again installed QT7.2 and over-installed FCP5.1.4 which has resolved my problems for the time being. Worth a try if you still can't get through on the DAC.
    Ron.

  • Unable to capture video from webcam in JMF in xlet

    hi
    I am unable to capture video from webcam in an Xlet. I am using Xletview to run Xlet. The method CaptureDeviceManager.getDeviceList(vidformat) returns empty array. Which videoformat should I use and why do I get empty array?
    Thanks
    Rajesh

    MHP and OCAP only use JMF 1.0, which does not include support for capturing video. You will not be able to do this in any current MHP/OCAP imlementation that I know of.
    Steve.

  • Unable to capture video from webcam in JMF

    hi
    I am unable to capture video from webcam in an Xlet. I am using Xletview to run Xlet. The method CaptureDeviceManager.getDeviceList(vidformat) returns empty array. Which videoformat should I use and why do I get empty array?

    MHP and OCAP only use JMF 1.0, which does not include support for capturing video. You will not be able to do this in any current MHP/OCAP imlementation that I know of.
    Steve.

  • What are the settings for capturing video from Canon HV20

    Hi All,
    I want to capture video from Canon HV20 with Premiere Elements 11. What kind of settings should I use to capture the video with full information?
    Here is what I did:
    1) According the manual, I went to Capture settings panel (Edit > Project Settings > Capture) and selected HDV as capture format, because my video is at high definition.
    2) In addition, I checked "Capture to Timeline" and "Split Scenes by cotent".
    Are these settings enough?
    Thanks.

    HV20user
    Sounds reasonable, using Add Media/HDV Camcorder, but....
    Have you reviewed the Adobe write up on Premiere Elements 11 DV and HDV capture firewire into it.
    http://help.adobe.com/fr_FR/premiereelements/using/WS5CDA0F91-60F1-4b79-ABF6-E9E75F498DB2. html#WS2AF26FB5-4C63-4c46-9DB3-7249558F6528
    The mention of Get Media instead of Add Media makes me wonder if the video's instructor was demo'ing from Premiere Elements 10, but...
    Major factors have always included having Premiere Elements project preset set correctly to correspond to your camera settings...For HDV data capture firewire...
    NTSC HDV HDV 1080p30 or PAL HDV HDV 1080p25 depending on if you are targeting a NTSC or PAL area where frame rates are typically a consideration.
    I had not done any DV or HDV data capture firewire into Premiere Elements. But, Premiere Elements 11's take over of the project preset setting would encourage me to encourage you to verify your project settings before the capture.
    There are probably many more, but the following is online discussion of one Canon HV20 issue
    http://forum.videohelp.com/threads/316970-video-capture-problems-HV20-camcorder-is-control led-but-no-video-capture
    If you experience difficulty with the HDV capture fireware into Premiere Elements 11, you might consider what some others have done in this regard, that is, use HDVSplit for the capture firewire and then import the split (.m2t) clips "Add Media" into Premiere Elements 11 with the appropriate HDV HDV 1080p (1440 x 1080 HD anamorphic 16:9) project preset.
    Please update us on your progress when you get a chance.
    Thanks.
    ATR

  • How do I import directly from Canon XA10 with Final Cut X?

    How do I import directly from Canon XA10 with Final Cut X?

    I have an XA10, and importing is quite simple.  But you do have to make sure your camera is set to the proper settings to allow you to import the files into FCPX.
    First, make sure the camera is powered on.  Connect it through the USB connection.  Then open the camera's viewfinder and press the button on the side of the camera that allows you to see the videos you've shot in the viewfinder.  (This toggle button toggles between seeing what the camera is pointed at live and seeing the thumbnails of the video you've already shot that are stored on the internal memory card.)  Now, the camera will present you with a menu asking which memory card you want to look at (there's an internal flash memory card, plus you can insert SD cards as well).  Choose the memory card on which your videos are stored within the camera, and then you'll be good to go.
    Now you can go into your FCPX event and do the Import from Camera.  Now the Import from Camera interface will open up and you'll be able to select the XA10, where it will present you with all the videos that are on the camera's memory card that you selected.
    From here,  you can select individual videos and import them, or you can set in and out points on videos and just import the parts you want.

  • HT1338 why I can't do capture from the camera in final cut pro x?

    why I can't do capture from the camera in final cut pro x?

    why I can't do capture from the camera in final cut pro x?

  • IHDPro/MBCC Error: Unable to figure our your host.  Assuming Final Cut Pro.

    So I have just installed FCE 4 and am encountering error messages upon start up. The messages read as follows...Message 1: "IHDPro Error: Unable to figure our your host. Assuming Final Cut Pro" as well as Message 2: "MBCC Error: Unable to figure our your host. Assuming Final Cut Pro."
    The first message initially appears upon FCE's loading of its video effects. I am given the option to press OK...so I press OK. FCE then loads a couple more video effects then that same first message reappears. I am again given the option to press OK...again I press OK. This happens one more time (for a total of 3 error messages of the first kind) until FCE loads a couple other video effects then displays the error message of the second kind. This error message displays twice, to which the OK option are offered by FCE and accepted by me both times. FCE finishes loading and all is ok.
    This issue was last brought forth on and only on this forum in December of last. The link to that topic can seen here: http://discussions.apple.com/message.jspa?messageID=6097916#6097916
    I'm unable to tell whether the issue was resolved since the topic has been archived (preventing replies) and due to the fact the the individual (Richert Goyette) who encountered this same problem has not listed an email to which I'm able to ask him of his resolution.
    Thank you for your time and effort in aiding in this matter.
    P

    I don't know whether this will help but the first thing to try when FCE does anything wrong is to trash the preferences exactly as described here:-
    http://www.fcpbook.com/Misc1.html
    If that doesn't work you could completely uninstall FCE 4 as described here and reinstall it:-
    http://docs.info.apple.com/article.html?artnum=301182
    You can ignore the LiveType and Soundtrack items.
    You might also want to trash FCP 6's preferences as well.
    Message was edited by: Ian R. Brown

  • Natively import the canon xf305 in Final Cut Pro X?

    Is there a driver or plugin to natively import the canon xf305 in Final Cut Pro X?

    Ok so, I'm upset that there is no native import from this camera. I have four of these cameras!!! But, I did find an interesting work around! I don't loaded free software from Sony. The same software used to convert XDCam to Final Cut. and it works great, not as great a native import. but here's the website I downloaded it from, http://pro.sony.com/bbsc/ssr/micro-xdcam/resource.downloads.bbsccms-assets-micro -xdcam-downloads-PDZKP1XDCAMTransferSoftwareTC.shtml

  • Best way to export from Motion 2 into Final Cut Pro 5, working in DV?

    I am working in DV in Final Cut Pro 5, and I would like to get the best quality from anything I bring in from Motion 2 into Final Cut Pro 5, I keep hearing use the Animation codec. I would like to hear from the Panel of experts.
    Happy Thanksgiving,
    Sebastian

    The Best way is to round-trip from FCP. Or simply import the .motn file directly into FCP. If you require an alpha channel and for some reason don't want to bring the .motn file in, Animation with millions+ for the colors (+ is the alpha channel) will work, But if you just want straight DV, you should export a DV file.
    Patrick

  • I am making a graduation video for my cousin using Final Cut Pro. I have photos layered over videos, and I was wanted to find out how you can add a border around the photos so they stand off of the video. Anyone know what I could do?

    I am making a graduation video for my cousin using Final Cut Pro. I have photos layered over videos, and I was wanted to find out how you can add a border around the photos so they stand off of the video. Anyone know what I could do?

    You would need an image editor to edit the images and add a border to the image first before importing them into Final Cut.
    Cheapest and very good image editor?
    PIxelmator.
    Located in the Mac App Store. $14.99 USD.
    Here is the Pixelmator website to give you an overview of the app.
    http://www.pixelmator.com/
    Good Luck!

  • When I export from the timeline in Final Cut Pro HD, I get a general error message

    When I export from the timeline in Final Cut Pro HD, I get a general error message and the export quits. Any ideas on a fix?

    Also, if I remember correctly, Final Cut Pro HD was version 4.5. Is this what you are running?
    If so, what version of OSX and Quicktime are you running?
    x

  • Why is there several minutes of black running time at the end of the videos I am producing in Final Cut Pro 6?

    Why is there several minutes of black running time at the end of the videos I am producing in Final Cut Pro 6?

    OK, wish you luck over there, seems like somebody over there should be able to help.
    If you don't get help, post back here & I'll try to find somebody in the top users that can help.

Maybe you are looking for

  • Preview bypassing PDF view settings

    Hey guys, another Preview issue here.  I created a PDF using Adobe Acrobat Pro.  The PDF setting on the file is to open in Single Page view with Bookmarks Panel showing. Preview opens it in complete disregard for these settings and I have to view it

  • How do you get the the task bar to appear on the cinema screen

    Just picked up a new Macbook Air. How do you get the task bar to appear at the bottom of the cinema screen? Thx, Chris

  • Enable as Hyperlink

    So, just recently I have noticed that, when I go into the inspector and the click the link tab and then check the "enable as hyperlink" check box the "Link To" drop down pane remains grayed out and doesn't open, this is a major problem because althou

  • Want to Have INT4 Data type field in IT

    Dear All,            I want INT4 Data type field in my Customized infotype field.            Is it possible to have it with signs. Thanks Satya.

  • Job Schedule Management

    Hi, We recently upgraded our Sol Man system to EHP1 and we are in the process of Job Shedule Management. We imported few jobs from managed system and while monitoring ,getting error Business Proccess not created. Could any one please tell me one thin