Unable to connect acer 500 wireless signal to E4200v2 (secondary router to fios)

I am not very tech savy and I am having trouble connecting my wireless devices to the e4200v2. My e4200v2 is connected to my action tec ver.F for fios. It's a LAN to LAN connection where the action tec is primary. I followed the directions changing the Secondary router address to 192.168.1.2 and the action tec stayed at 192.168.1.1. I also reset the action tec prior to any attachments (because I had an old belkin n+ connected). i also disabled DHCP in the secondary router. Both 5 & 2.4 Ghz have different passwords although I did try having them have the same password- no luck. I can't connect for whatever reason. Both network modes are mixed. On the action tec- the wireless is disabled. SSID are different. Can't connect for whatever reason. I am at a loss. I don't know if this is relevant- I use windows vista.
Any suggestions?
Thanks!
Solved!
Go to Solution.

Try using WPA2-AES and connect one device at a time to see if each device individually can connect.  Than add one device at a time.

Similar Messages

  • I'm unable to connect to my wireless network

    I am unable to connect to my wireless network on my iphone 4.  It worked previously. My husband has no problem with his iphone connecting.

    Same here. Upgraded 2 separate iPhone 4 to iOS 5 and now both get an error that say "incorrect password" when trying to connect. iPad 1 upgraded to iOS5 and all 3 macs connect fine using same password. (Router is Apple Airport base station running 7.5.2)

  • Macbook air is unable to connect on hidden wireless network

    Dear users and support,
    I have just bought my macbook air with lion os already installed, but I am unable to connect to hidden wireless network. Is there any trick to fix it? even though I am typing the name and password it's unable to login.
    Please advice.
    tks,

    Back up all data before making any changes.
    Step 1
    Take all the applicable steps in this support article.  
    Step 2
    If you're running OS X 10.8.4 or later, run Wireless Diagnostics and take the remedial steps suggested in the summary that appears, if any. The program also generates a large file of information about your system, which would be used by Apple Engineering in case of a support incident. Don't post the contents here.
    Step 3
    This step will erase all your settings in the Network preference pane. Make a note of them before you begin, and recreate them afterwards. It may be helpful to take screenshots of the preference pane.
    Triple-click the line below on this page to select it:
    /Library/Preferences/SystemConfiguration
    Right-click or control-click the highlighted line and select
    Services ▹ Reveal
    from the contextual menu.* A folder should open with an item named "SystemConfiguration" selected. Move the selected item to the Trash. You may be prompted for your administrator password.
    *If you don't see the contextual menu item, copy the selected text to the Clipboard (command-C). In the Finder, select
    Go ▹ Go to Folder...
    from the menu bar, paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.
    Reset the System Management Controller.

  • Unable to connect to any wireless internet

    laptop not supported any dongal to connect internet where as device connected other laptop. If i connect with Hot s[pot then its connected so request you to help on this & suggest what should i do.  shoud i format ?

    Hello @James0007,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I have read your post on how your notebook computer is unable to connect to any wireless network. I would be happy to help you, but first I would encourage you to post your product number for your computer. Below is a is an HP Support document that will demonstrate how to find your computer's product number. In addition, it will also help if you indicate which operating system you are using; and whether your operating system is 32 or 64 bit. The more information you can provide, the better!
    How Do I Find My Model Number or Product Number?
    Which Windows operating system am I running?
    Is the Windows Version on My Computer 32-bit or 64-bit?
    Please re-post with the necessary information, this way I will be able to research this further for you. I look forward to your reply!
    Cheers!  
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • Unable to connect to home wireless network with my iPod touch

    I've had my iTouch for several months now and I'm still not able to connect to my wireless network at home. I've tried the resets and other suggestions I've found in the discussion groups but nothing has worked.
    I have an older Netgear Router MR814v2 and it is unsecured. It is attached to my old desktop, HP Pavilion running Windows ME, which is not able to run the itunes software. My HP laptop is where my iTouch and iTunes software is installed.
    The iTouch displays my network with good signal strength, but when I try to connect I get the "unable to join the network "NETGEAR".
    Going to my router, it does not recognize my iTouch as an attached device. Why is that and what am I missing?
    Thank you for all suggestions and your help.

    I tried powering down the router. When it's off the iTouch does not recognize the network and then when it's powered on again, the iTouch recognizes the network. Unlike the public wi-fi spots that my iTouch responds to, where all the info like IP Address, Subnet Mask, Router, DNS etc are populated in the settings...my iTouch does not populate these fields at home even though it recognizes the network. I still get the unable to connect to network error. Could it be that my router is antiquated and can not support the iTouch? Like I said earlier, my Router does not recognize the iTouch as being attached to it.

  • Unable to connect to printer wirelessly

    I have an Hp Officejet 7612
    My computer is running Windows 7 64-bit with Service Pack 1
    I am not able to connect to my printer wirelessly.
    When trying to add printer, after selecting "Add network, wireless, or Bluetooth printer", my computer is not able to see printer while serching. I try to add printer manually by typing in IP address or hostname (either one), an error message occurs.
    Printer wifi is on and connected to the same network as the computer.
    I have restored network settings to default in order to try and fix issue.
    I've tried this on a number of other computers, some running Windows 8.
    I have disabled computer firewalls and computers still can't find printer.
    It is as if the printer is...invisible!

    Hey @chriswalkenspal ,
    Thank you for taking the time to post on the HP Forums today! Hope you enjoy the experience.
    I understand you have your printer and computer connected to the same network and you are unable to connect your computer to your printer.
    You say you are trying to add a printer, but have you installed the printer using the device driver CD or online driver  download tool ? If you haven't you need to do so and you won't have to add a printer because that is all done in the installation.
    If you need the instructions on how to do so, let me know and I'll be more than happy to show you how to do download it.
    Have a great day and let me know what else I can do for you.
    I worked for HP.

  • Unable to connect netgear DG834G wireless to macbook

    Hi
    I am unable to connect the Netgear Router DG834G wireless to my Macbook. It works fine through the ethernet cable but when i try and connect wireless it says invalid password?

    Hi
    Changing your ISP won't fix this problem.  There is one last thing that's worth a try....
    Creating a new "Location":
    System Preferences > Network
    Select the AirPort from the left hand side
    Click on the Locations combo box and select Edit Locations...
    Click on + to add a new location, call it "Home" (or anything else you prefer)
    Click on Advanced
    Select the AirPort tab and enter your network name
    Select TCP/IP tab. 
    Configure IPv4 Using DHCP
    Now click on Renew DHCP Lease.  After a few seconds you should get an IP address (probably 192.168.x.x)
    Click on Proxies tab.
    Select Auto Proxy Discovery and Use Passive FTP
    Click on OK and Apply, etc.
    If this doesn't fix your problem then I suggest your Airport card is failing and you need to visit an Apple Store.
    Bob

  • Unable to connect to new wireless network in Mountain Lion with Photosmart C4780

    I have a Photosmart C4780 and have just upgraded my imac to Mountain Lion. HP are not providing new drivers for my printer as they say it will work with Mountain Lion. I have downloaded software updates. However, I have just changed my wireless network as I have a new broadband provider but am unable to connect to it. My problem is that the set up assistant software provided which I used originally to set up does not work with Mountain Lion.
    Any ideas please?

    I have solved my problem, I've bought an Epson. It works perfectly. If HP can treat their customers with such disinterest and contempt I don't want to give them my money. 

  • Macbook (10.4.11) unable to connect to one wireless network

    We have one student who is unable to connect to our student wireless network. He's using a Macbook (black) with 10.4.11 and all updates. He's got a stock Airport card. We have an Airport Extreme broadcasting the network. Other students are able to connect without any problem. He's able to connect to our teacher's network without any problem.
    When we try to connect his airport to the student network, it reports "There was an error joining the AirPort network 'Riverstone Students'." No further information is provided. I've tried removing it from his preferred networks, removing the key from the keychain, and reconnecting, but no change.
    Any suggestions gratefully received!

    Just found out a little info about my work network. We are using a SMC Network 8014 W-G broadband modem and a Linksys WAP11 Wireless Access Point, and the security is WEP. I have tried to login to the device webpage to check/adjust settings but nobody here knows the password and "admin" doesn't work. I really don't want to do a hard reset and take the chance of screwing up the network for everybody in the office (apparently it was quite complicated to set up when they first installed it, I wasn't around then). Does anybody have any other ideas? Thanks

  • Unable to connect with the wireless feature

    I have the Linksys WRT54G version 8.0, it bridges with my DSL modem.  I have 3 wired desktops and 1 wireless laptop (which does not connect without wired connection).  According to the easylink advisor, we do not have an internet connection.  But I have internet connection as long as all 4 computers are wired in.  My problem now is we have a new ps3 and can not do the wireless connection.  I have checked all settings on router page and still shows no connection.  What am I doing wrong?  How do I fix this?  I can get on-line just can't use wireless.  Can anyone help?
    Thanks,
    Sharon

    You need to do Port Forwarding on your Linksys Router...
    Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
    Leave username blank & in password use admin in lower case...
    Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
    1) On the first line in Application box type in ABC, in the start box type in 80 and End box type in 80, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
    2) On the second line in Application box type in DEF, in the start box type in 443 and End box type in 443, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
    3) On the first line in Application box type in GHI, in the start box type in 5223 and End box type in 5223, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
    4) On the first line in Application box type in JKL, in the start box type in 3478 and End box type in 3479, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
    5) On the first line in Application box type in MNO, in the start box type in 3658 and End box type in 3658, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
    6) On the first line in Application box type in PQR, in the start box type in 10070 and End box type in 10080, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings
    7) Now assign the given ip address on your PlayStation
    ip address :- 192.168.1.20, subnet mask :- 255.255.255.0, default gateway :- 192.168.1.1...
    8) Also assign the dns addresses on the PlayStation
    Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
    9) Turn off your modem, router, and PlayStation...Wait for a minute...
    10) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the PlayStation and test it...
    As your PlayStation is Wireless make sure you are connected to your Wireless Network...

  • Unable to connect laptop to wireless network

    My MacBook Pro will not connect to my wireless network, but my iPad does so I know it must be a problem with my computer rather than the network. Any suggestions?
    I'm not sure if there is some obscure setting that I need to change.

    Give us more information, please.
    Is your wireless network supplied by your ISP, your landlord, your own router, or something else?
    What can you tell us about the settings on your wireless network? (Not the passwords.)
    Did this ever work, or is this the first time you have tried to connect the MBP to this wireless network?
    What model/year MBP is this? It has to be somewhat old if it is running Snow Leopard (10.6.8) as per your profile.

  • How can another computer connect to my wireless signal?

    I have a great wireless signal running through my time machine, but my friends who visit cannot get into it.  They are running off the neighbor's wireless signal which is not as strong.  I have set internet sharing to ON but it is not offering WiFi  as an option.  I have a feeling it is time machine settings somehow but don't know how.  Any suggestions?

    Assuming your friend is using a Mac.
    Go to Apple Menu / System Preferences / Network.
    Select Airport on the left, and click on the Network Name that is displayed (which will probably be your neighbour's network).
    Select: Join Other Network.
    Click on Show Networks.
    Select the network you want to join.
    Enter the password
    Click on Apply.
    You only need to do this once. The next time your friend visits, the Mac will remember the network and the password.

  • Powerbook G4 Can't "See" Wireless Signal from Ubee Modem/Router

    I was given a G4 Powerbook while out of town and it found the wireless signal in an apartment complex and a major airport just fine. But upon returning home it can't "see" the signal from my (Time Warner, Road Runner Extreme) Ubee modem/router. My Mac Mini's Airport sees the Ubee wireless signal fine, but the older Powerbook G4 can't. (The Airport signal in the menu bar has "bars" but they are grayed out.
    Can an older G4 connect with the newer Ubee modem/router? Are there security settings that will allow this?
    Tx,
    WK

    CRMDVM -- Thanks for the helpful info -- you are probably right on both counts:
    The apartments where I picked up a signal is in an "old folks" apt. complex, meaning the router I was picking up was probably old -- compatible with the G4 lineage. And the Atlanta airport probably has a wireless system to allow the vast number of old and new computers that people carry to connect.
    My Mac Mini connects via WPA2 Personal security code, and I set the G4 to the same security (in the Network preference pane) but still nothing. The Airport wireless icon in the menu bar is still grayed out -- it isn't the "blank" icon as when Airport is turned off. It has the wireless wave lines in the icon, but just grayed out.
    Maybe the G4 is just too old to "see" the newer wireless signal from the new modem/router.
    Thanks again for your help -- you definitely provided more than I knew. (btw, I'm just above you in Union County in Stallings).
    WK

  • Re: WRT350N ----- Very poor Wireless signal strength from my router

    I have a WRT350N router.  I had it for a year now.   In the begining the Wireless Signal strenth was good. 
    I used to get 4-5 bars in my bed room which is about 10 meters from the router. 
    Now I have my laptop sitting 1 feet away from the router and I get only 1 bar.
    I upgraded my firmware.  I rebooted my router a few times still no luck.
    Current Firmware Version:  v1.04.4 build 003 Jul. 14, 2008
    Can any one tell me whats the problem. More importantly can some one help me resolve this problem.
    Thanks
    Sunny

    As you upgraded the router's firmware,I would suggest you to reset the router for 30 seconds and reconfigure it from the scratch, as it is advisable to reset the router after upgrading the router's firmware.
    On the router's setup page,Under Wireless tab..Give unique name in the Wireless Network Name (SSID). Change the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz... Under the Advance Wireless tab,change the Beacon Interval to 75 and click on save settings.... Now,check.

  • Unable to connect to unprotected wireless network

    A couple of months ago, I upgraded to Snow Leopard (10.6.4) from Tiger with the Mac Box Set. Ever since then, I have had a pretty mysterious problem: the wireless internet in my apartment, only for MY computer, is extremely unreliable, allowing me to connect about 5-10% of the time.
    I have 3 roommates, running Leopard, Tiger, and Windows Vista. They have all had no problems throughout my battle with our router. The default protection was WEP,and I had read in some forums that snow leopard has problems with WEP, so I changed the security to WPA. That worked for a bit, but a day or two later, no chance.
    I can always see the network as an option, see that it has a significantly strong signal, and am just not able to connect. I guess pretty much what happens if you type in the wrong password.
    So, after this disappointing turn, we decided to try it with no password at all. Great. That worked too. For a day or so. Then, same problem. Can't connect, although my computer obviously sees that the network is active.
    This is probably my favorite part: when I run diagnostics or setup, I am told that I might have the wrong password. Oh, the frustration!
    I have dumped preferences, deleted locations, deleted airport, etc etc to no avail. As with the network tooling, it occasionally works for a day or a few hours and then the problem returns.
    The other three computers in the house have no problem connecting. Full connection. So odd.
    Even stranger? My computer connects just fine everywhere else. WPA2,802.1x, WEP. It's just at my house.
    I've also tried changing the channel, which has worked, again, sometimes for a day or so, sometimes not at all.
    Oh, also lovely - occasionally, it just mysteriously works. IE, it has not connected for a week, I turn it on, and it's magically connected. No changes to settings, no restarting even. (which I have obviously also tried).
    At this point, I am convinced it's haunted, becuase, knowledge of wireless technology or not, there seems to be very little logic in the situation.
    I've talked to the router people, service people, etc, read the manuals, etc etc, but the people are all sure it's my computer because my roommates' computers work, but I'm sure it has something to do with them, because I can connect elsewhere. So any tips on router settings I may not have thought of are also welcome. Very confusing.
    please help!

    Try Static IP address and update to 10.6.5 with combo update.

Maybe you are looking for