Unable to connect LaserJet CP1525nw to Wireless Network
I have new Ubiquity router. It is broadcasting our SSID. I am trying to connect a LaserJet CP1525nw to the wireless network. I cannot figure out a way to enter the SSID on the printer. The Ubiquity router does not have a WPS button, so that is an option. I did attempt to use the USB connected device, but the installer would time out, always providing the same error, that it could not connect to the printer (this in spite of the fact that the printer is on and connected via USB).
Hi Kfran615,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I see that you are having some issues when attempting to install the printer. So I can better assist you,please respond with which Operating System you are running.
Which Windows Operating System am I running?
Mac OS X: How Do I Find Which Mac OS X Version Is on My Computer?
Thank you for your time.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP
Similar Messages
-
HP Deskjet 3050 - Unable to connect to WPA secured wireless network
Hello,
My first post here so please excuse any faux pas on my part. I bought this HP Deskjet 3050 a week ago and have been waging war with it ever since. I'd be really grateful if someone could possibly advise on how I can resolve this.
I am unable to connect the printer to my secured wireless network, even though other computers, cell phones, etc. are connected without issue. I have tried WPA, WPA2 and WPA2-Mixed security modes with the same failure. Specifically, the connection wizard reaches 66% and then displays the error that the wizard is unable to find network/printer. If I disable the security, the printer connects fine.
I'm using a Linksys WRVS4400N router with firewall and associated firewall settings disabled. The router is broadcasting on 802.11G/N mixed mode.
I'm installing the software supplied on the setup CD on a Windows XP SP3 system. I have confirmed that the network the PC and printer are connected to are the same.
A question as well, if I may: I haven't tried these drivers yet but I see there are updated drivers for the printer dated 14/12/2010. The release notes indicate improved networking, but don't elaborate beyond this. Does anyone know if there was a known problem with connecting to secured networks that has now been fixed?
Finally, just a note that I'm partially sighted and am using a screen reader on all systems. I'll try my best to be as helpful as I can but please do excuse me if I occasionally can't find settings, etc. on screen and need a bit more detailed help.
Thanks in advance for your help, which I really will appreciated.
Have a pleasant day,
All the best for now and take care,
Hussein.
It's not the fact it can't be done, it's the fact it hasn't been done, yet.
This question was solved.
View Solution.HI,
firstly, apologies for the delay getting back to you. Poor health has meant I've had little time nor inclination to do much on the computer side of htings.
Anyway, I'm please to say the problem with the HP 3050 failing to connect to my network is now solved. It seems to be a bug with the setup software, and that seems to include the latest version posted Dec 2010.
To resolve the problem, I did the following:
1. Disable all security options for the network, so it's just an open network.
2. Connect the HP 3050 to the network using the setup wizard. This time it connected OK for me.
3. Locate the printer's IP address. I used the client list table accessed through my router's interface. You may be able to get this through the printer's on-screen menu, but as I'm partially sighted, this wasn't an option for me.
4. Log into the printer's control panel at http://ip.address.of.printer e.g. http://192.168.2.108
5. Under the advanced options, configure the settings for the network, including security protocol and passphrase. Remember to enter the SSID of the network exactly as configured on the router.
6. Apply the settings and log out of the printer's control panel.
7. Log back into the router's control panel and re-apply the security options. Be sure that they match those match those entered for the printer.
Hopefully this will be of use to others in the same position.
Thanks again for your time.
Best,
H.
It's not the fact it can't be done, it's the fact it hasn't been done, yet. -
Hi,
I have a Dell Latitude E6440 running Win 7
Enterprise 64 on a domain. It will connect to any unsecured network, and it can see the secured network in the list when I click the wireless connection icon on the system tray. When I go to manage wireless networks, the secured network does not show
up (and thus, I cannot delete the network to try to re-add it). Normally, we would add the secure network here. I click Add, give the name in the correct syntax, add the needed information (WPA/2-Enterprise, EAS or TKIP), and hit Next, it immediately returns
with "An unexpected error occurred". A similar thing happens when I hit Connect from the list of available networks that pops up when I open the system tray icon: it says it was unable to connect, when I hit troubleshoot, it says that it could not
identify the problem. The event log shows the error below. I haven't been able to find any resolutions here or elsewhere that address the fact that I can connect to unsecured wireless networks, but not secured wireless networks.
Other notable troubleshooting steps:
Uninstalled/Reinstalled wireless adapter with the latest driver
Other laptops are able to access the same secure wireless network
The first WLAN-AutoConfig error in the event log was Event ID: 12013, attempting a 802.1x authentication. Then Event ID: 11006; stating "Explicit Eap failure received". After a few days of alternating all 3 errors, they started to only error on
Event ID 8002.
Log Name: Microsoft-Windows-WLAN-AutoConfig/Operational
Source: Microsoft-Windows-WLAN-AutoConfig
Date: 6/4/2014 11:53:55 AM
Event ID: 8002
Task Category: AcmConnection
Level: Error
Keywords: (512)
User: SYSTEM
Computer: [COMPUTERNAME.DOMAIN]
Description:
WLAN AutoConfig service failed to connect to a wireless network.
Network Adapter: Intel(R) Centrino(R) Advanced-N 6235 Interface GUID: {f27af762-dff8-4927-84e0-7f4ade30dcc9}
Connection Mode: Connection to a secure network without a profile Profile Name: [SECURE NETWORK NAME]
SSID: [SECURE NETWORK SSID]
BSS Type: Infrastructure
Failure Reason:The specific network is not available.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-WLAN-AutoConfig" Guid="{9580D7DD-0379-4658-9870-D5BE7D52D6DE}" />
<EventID>8002</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>24010</Task>
<Opcode>191</Opcode>
<Keywords>0x8000000000000200</Keywords>
<TimeCreated SystemTime="2014-06-04T16:53:55.956762800Z" />
<EventRecordID>1475</EventRecordID>
<Correlation />
<Execution ProcessID="432" ThreadID="5348" />
<Channel>Microsoft-Windows-WLAN-AutoConfig/Operational</Channel>
<Computer>[COMPUTERNAME.DOMAIN]</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="InterfaceGuid">{F27AF762-DFF8-4927-84E0-7F4ADE30DCC9}</Data>
<Data Name="InterfaceDescription">Intel(R) Centrino(R) Advanced-N 6235</Data>
<Data Name="ConnectionMode">Connection to a secure network without a profile</Data>
<Data Name="ProfileName">[SECURE NETWORK NAME]</Data>
<Data Name="SSID">[SECURE NETWORK NAME]</Data>
<Data Name="BSSType">Infrastructure</Data>
<Data Name="FailureReason">The specific network is not available.</Data>
<Data Name="ReasonCode">163851</Data>
<Data Name="ConnectionId">0x6</Data>
</EventData>
</Event>check this article:http://technet.microsoft.com/en-us/library/cc735927(v=ws.10).aspx
also could contact your domain administrator to ask for help. -
I am new to IPod Touch and enjoying but all of a sudden (after about a month of connection) I am unable to connect to either my home wirless or hotspots outside of home. It would appear that a setting has changed but have no idea how to determine. Any suggestions ?
NO I did not and thank you very much for the advice. My problem was stated incorrectly in that while I am able to connect to the wireless from that point on I am unable to connect to the internet. I will check the article referred to.
-
Unable to connect to internet using Wireless WPA after installing XP SP3
Hi guys,
Just installled XP SP3 on my X40 and now I cannot connect to a WPA wireless network. I have updated the drivers etc but still no luck.
Has anyone else got this problem and been able to fix it.
I'm sure that if I uninstalled SP3 then it would work but I'd rather get a fix.
Message Edited by mundo on 08-13-2008 12:57 PMI, too, am unable to get a good "connected" session with WPA.
I have tried Windows Wireless: stays in the mode: "Authenticating."
I have tried Intel Proset Wireless: stays in the mode: "Connecting."
I have tried Access Connections: stops after saying "Waiting for association."
These different programs allow me to set up WPA profiles, and they see wireless networks and can communicate with them.
I am on a Thinkpad T-42 (2373-Y3U). Intel adapter 2200bg. Windows XP Pro, SP3.
I have tried WEP, and it works fine. Other computers connect to (multiple, different) routers with WPA that I have tried, to no avail.
I loaded latest Intel driver (file name: 7vwc15ww.exe, dated July 29, 2008). But does not work...
I have tried going back to old drivers, but does not work. I have tried the steps: unload driver, load HotKey, Load PowerManagement, Load Access Connections, as described elsewhere, but does not work.
Why is this so hard. Should be a no - brainer, it seems to me. I've spent hours...
Thanks, Todd -
I currently have a WPN824 v3 Netgear router and I’m trying to set up my Apple TV. I am able to connect it to my wireless network but my airplay feature is currently not working. The icon does not appear on any of my devices. My ipad and ipones all are currently up to date and are all joined to the same network. Is it the way that my router is configured. Please help let me know what I need to change in my router settings or does my router not work with Airplay. Or is there a simple fix.
you don't mention which products you use
only ipad2 and up support mirror
and only iphone4s and up support mirror
other devices only use airplay for apps which support tvout options -
Hi,
I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand-new (the 4th time to use the device) a while ago i was trying to connect to my home wireless network it said that the connection is timed out so i clicked the airport sign on the top it said that your airport is not configured then I restarted the system but it didn't restarted it showed the grey screen with the apple logo and the spinning wheel for more than 10min so I tried the force shutdown by pressing the power button till it switched off I waited for 5min then pressed the power button to start or boot the system and again the grey screen with the apple logo and the spinning wheel, I waited for more than 20min nothing changed, any solution please?
Your help is really appreciated"Thanks a lot i followed the instructions for safe mode (i found out that i was pressing the C button after restarting) i did whats written there but the repair couldn't be performed so in addition i needed to re-formate the HD so i erased the volume and then repaired the disk--> quite disk utilities --> start the installation from the installation DVD.
Thanks really appreciating your help -
After updating to iOS 6, I can no longer connect to my schools wireless network. It uses manual http proxy. Now however a blank pop up comes up and it will not connect you. Thanks
Turn off your firewall and antivirus software.
-
Can't connect AE to existing wireless network
I can't get my AE to connect to my existing wireless network. I saw the other thread on this and followed those steps, but it didn't work. Here's what I did:
1. Connected the AE to my D-Link DIR-655 wireless router via ethernet cable.
2. Opened Airport Utility and established a connection to the AE.
3. Renamed the AE and entered a password.
4. In the "wireless" tab, I selected "join existing network", chose my wireless network, selected the security type (WPA Personal) and entered the password.
5. In the "music" tab, I named the speakers and entered a password.
So far so good. I clicked "update" and the AE restarted. After a while I received an error message informing me that the base station could no longer be detected. According to the directions posted in the other thread, this is actually supposed to be a sign that the AE is now in client mode and all is well.
I unplugged the ethernet cable from the AE and router and then went to the other room. I plugged the AE into the speakers and then plugged the AE into the wall.
However, instead of a green light all I have is a flashing amber light, even after several minutes. No connection.
I reset the AE and repeated the steps above, to no avail. Still a flashing amber light.
Any ideas?I'm having a similar issue. My AE is connected directly to a Netgear WGR614v4 router, and I run through all the steps you mentioned. When I choose to update the settings to the AE, I get the same "error" you mentioned about the AE not being found, and I also took that as a sign that I'm in client mode. I moved the AE to the other room, connected my mini cable to the stereo, then plugged the AE back into the wall. The AE runs through its setup and eventually gets a solid green light, so I'm thinking all is well.
The problem is that I then log back into the AirPort Utility on my laptop and the AE is not shown in the top left like it should be. After doing a bit of reading, I've figured out that I can manually find it by going to File>Configure Other and entering the AE's IP address and password. Then I get a window showing the details of the AE, its name, network, encryption, etc. However, if I close this window, it still doesn't show up in the main AirPort Utility screen and I'm not sure how to configure it for AirTunes.
Hoping that's just a bug with the AirPort Utility software, I open up iTunes to see if I can locate it there. I know I should see a pulldown menu at the bottom of iTunes that gives me an option for AE as my audio output method, but the menu is not there. Now I'm completely stuck.
At this point I decide to start from scratch, so I do a Factory Default reset by pressing down the reset button on the AE as I plug it into the wall. Now it is supposedly reset, so I plug it back into my router, then it runs through a setup sequence and lights up solid green before I've even done anything. It shows up in AirPort Utility with a default base station ID, but my computer won't connect to it at all. I'm hoping I can try to reset it again this evening and at least get back to the normal setup screen, but I'm really not sure what I could do differently at this point.
This is frustrating and I'm on the verge of giving up, but I REALLY want this to work out. -
I have an eMac which I want to connect to my home wireless network. My router is D-Link - 601 tech. 802.11n. My eMac is wireless ready but does not contain an airport card. Do I need a card and an airport station? What else?
You need the Airport card OR Airport Express but not both. Considering the age of your machine, I recommend Airport Express as you will find other uses for it whenever you replace the eMac.
To set up the AE, you do need OSX 10.4 or higher. -
I have followed all relevant steps, my iPhone5 and apple TV are connected to the same wireless network, but I still cannot use airplay. When I choose the airplay option on my phone, the only option I get is "iPhone"
Welcome to the Apple Community Willy.
Try the following steps, check whether things are working after each step where appropriate, before trying the next.
Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
Restart the Apple TV (Settings > General > Restart).
Restart the Apple TV by removing ALL the cables for 30 seconds.
Restart your router. (Also try removing it’s power cord for at least 30 seconds)
Restart your mobile device. -
iPad 2 doesn't recognise my password for wifi. Unable to connect. Tried resetting the network,changed the wap settings,nothing. Pswd is 9 characters. MacBook and iPhone accepts the password, not my ipad 2
Hey brainmasala,
Thanks for using Apple Support Communities.
Sounds like you are not able to connect to a Wi-Fi network with your iPad. This article has a section for Unable to connect to a Wi-Fi network and the second article is the recommended network settings. If after these it still has the same issue you may want to restore the device to factory settings.
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/HT4199
Use iTunes to restore your iOS device to factory settings
http://support.apple.com/kb/HT1414
Have a nice day,
Mario -
Need to configure Airport connection to access corporate wireless network
Need to configure Airport connection to access corporate wireless network.
Have imported my certificate from Windows XP machine into keychain and made Leopard always trust in order to authenticate automatically into my corporate wireless network. Also attempted to establish a new 802.1x connection via network preferences without any success. It keeps asking me for username and password even though we used self-generated certificates to log into corporate wireless network. Does anybody have any instructions on how to successfully configure certificates in Leopard?Welcome to the discussion area, jackregan!
You'll need to "hard reset" the Time Capsule and then reconfigure it again. To do this, you will hold in the reset button until you see the amber light begin to blink more quickly, keep holding another second or two and then release.
The "hard reset" will not affect the data on your Time Capsule
Now you can open AirPort Utility and configure the Time Capsule using wireless (be sure to log on to the default network which will have a name like Apple Network xxxxxx), or you can connect an ethernet cable from your computer to one of the LAN <-> ports on the Time Capsule to have AirPort Utility communicate with it that way.
When you open AirPort Utility, click Continue to follow the guided setup to re-configure your Time Capsule. You would choose the option to "Create a wireless network" when you are given the configuration options. -
I have two facetime users, both connecting to our enterprise wireless network (Cisco WCS) and they can't make a facetime connection from IPAD to IPAD. Are there any apple protocols or other settings that need to be enabled on WCS? There is no firewall inbetween the two connections, as this is all on our internal network.
Both devices can connect to the network, but when they try to talk to each other they can't make the connection.
Thanks.If anyone ever comes across this and has the same issue, here's what I did to fix it:
My Linksys router has a Network Mode setting, and I had to change it from "Mixed" to "Wireless-G only". (I would've used N but one of the NICs in my house is too old to support it.) Anyway, after making this change, Facetime works fine on the phone. Hope this helps someone else! -
Vista connection problem to a wireless network with Linksys BEFW11S4 ver.4 router
I've purchased a laptop with Vista and can't get it to connect to my existing wireless network. I have a Linksys BEFW11SF ver.4 router. When I attempt, I get, "Wireless connection failed because the network denied the association request from this computer." Anyone? Thanks.
Not sure about the Error ....but you can change the wireless settings on the router & see if it connects or not ....
Maybe you are looking for
-
I Pod Classic is NOT being recognized and I get a "sick" IPOD icon on it
What to do?? I can't restore it because it is not being recognized by itunes. It flashes a lightning bolt through the battery icon on the screen. Any ideas? Anyone? Bueler?
-
Email Notification as Outlook Reminder
Our Client uses Outlook as the email Client and wants to have reminders set on outlook automatically for trainings scheduled in OLM. I would like to know if it is possible to send email notifications in a way that they would be considered as reminder
-
Password and security Forget and blocked Please send information to. [email protected] thank you
-
How to set the default focus to a particular jtextfield
hi, i'm trying to set the focus to the specified Jtextfield by default. i tried with reqestFocus() method,grabFocus() method,getCursor() method but all in vain. can anyone suggest me a solution please. very urgent request please thanks in advance reg
-
LaCie Mini not showing up as available for TM
I have been using a LaCie Mini 500 gb drive as my time machine drive for a 6 months. Now it does not detect the drive properly when I plug it into my computer. It was recognizing it yesterday, but it would become available during the backup. Today it