Unable to connect Panasonic HDTV to home network via Wi-Fi

I am unable to connect my Panasonic TC-L37E3 to the internet via Wi-Fi.  I purchased the additional Wi-Fi adapter for the set, and while setting up the connection I am able to see my wireless network on the TV.
I have a basic WEP key, but I am unable to connect to the network via any of the connection options given.  For every option there is a two minute timeout which is the eventual result of each connection attempt.
My router is 9100EM, with at 10M/2M service plan.  I am unable to connect the TV directly to the router via CATV since it is a considerable distance.
Has anyone experienced a similar issue or can suggest any troubleshooting actions?
Any help is greatly appreciated!

Try switching the router off of WEP and onto WPA2. There is a WEP Setting regarding Authentication that allows for Open or Closed authentication, but even then, devices expect Open. WPA2 is faster and more secure, and it's a good bet that the TV will work once you switch the router over.
You can change the security settings by going to http://192.168.1.1/ and logging in using admin as the username, and your router's serial number as the password. In the Advanced Wireless Settings, you'll find the option for WPA2. Enable that option with Pre-Shared Key and set a Passphrase (if one is not already set), and then set up your devices to use that Passphrase (is case sensitive) once you apply the settings.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Similar Messages

  • Connecting Ipod Touch to Home Network via Linksys Router

    After hours of frustrating attempts and able assistance from Apple product specialists and Linksys agents the issue was finally resolved inadvertently. Here's the solution for anyone having trouble:
    1. Perform a hard reset on the router - holding tiny red button next to the power cable in for 30 seconds.
    2. Perform a soft reset on the router - unplug the power cable for 30 seconds.
    3. Reset your cable modem.
    4. After rebooting everything, go to your router pages on the web. Re-establish your network settings. Make sure the Wireless Mac Filter setting is disabled. That worked for us. Hope it will save others the time and trouble we experienced.

    Thanks for posting your resolution.
    I would also like to mention that Linksys router owners should always update their router firmware to the latest version when encountering connection issues.

  • TS1398 i just updated the ios on my iphone4s and now i cannot connect back to my home network ... my network pass is still the same but it keeps saying unable to join network

    i just updated the ios on my iphone4s and now i cannot connect back to my home network ... my network pass is still the same but it keeps saying unable to join network

    i just updated the ios on my iphone4s and now i cannot connect back to my home network ... my network pass is still the same but it keeps saying unable to join network

  • Ipad will no longer connect to my private home network

    i have always had my ipad mini connected to my private home network for over a year and just 3 days ago it no longer connects to my network! Why is that and how can i fix it???
    i have no problems with my iphone 4s! it still connects to my wifi!

    If you are having WiFi problems it is necessary to isolate whether the problem is with your network or your iPad. Note: Do NOT consider your network to be blameless if some other devices can connect to it.
    First, test your iPad on some other WiFi networks: a friends, Starbucks, Barnes & Noble, etc.
    If it works well there then the problem is probably with your network. Try restarting your WiFi router by removing power for 30 seconds. If that does not help check for a firmware update for your router. If none exists which corrects the problem consider replacing the router.
    If your iPad does not function well on other networks it possibly has a hardware problem. You could try Settings > General > Reset > Reset Network Settings to see if that corrects the problem. If not, contact Apple Support or visit an Apple store for evaluation. They can provide a replacement if your iPad is bad.
    If you need more help please give the make, model, and version of your WiFi router and how you have it configured.

  • MacBook Pro does not sense external monitor (Panasonic HDTV in my case) via thunderbolt-HDMI connection...Is update 10.8.3 helping anyone?

    My MacBook Pro (newest model in 2013 so far) does not sense external monitor (Panasonic HDTV in my case) via thunderbolt-HDMI connection...Is update 10.8.3 helping anyone else who has this issue? I returned my multiple HDMI adapters after figuring out it had to be an Apple issue n not the adapters so I can't check it myself now.
    Thanks!

    I have late 2012 MBP 13" and connect to my Panasonic Plasma correctly.
    But using the same cable, can't connect to an LG 47LM6200, the MBP detects the TV, the screen blinks blue, but the TV shows "no sinal detected" message.

  • I am unable to connect my ipad to the internet via wifi, when asked for my password I get message "unable toI ge join network" however my laptop is able to access the internet using similar procedures and in the same physical location.?

    I am unable to connect my IPad to the internet via WiFi, when asked for a password then attempt to join I get the messag "unable to join the network" however  if I use my laptop in  the same physical locationand using similar procedures I am able to conect.?

    What router are you using? make/model/version
    What security type are you using? If it is WEP then symbolic (non hex) keys may be converted to hex in different ways by different operating systems. Is your laptop a Windows PC?
    If you are using WEP then drop it and move to WPA2. WEP has been deprecated by the WiFi alliance since 2004 as insecure (it can be hacked in seconds).

  • I replaced my phone at apple y'day, due to a broken screen. Brand new phone, but i am unable to connect to wifi, at home or work, so presuming its a fault with the phone? not router, i have also done a software update, is there a solution? thanks

    i replaced my phone at apple y'day, due to a broken screen. Brand new phone, but i am unable to connect to wifi, at home or work, so presuming its a fault with the phone? not router, i have also done a software update, is there a solution? thanks

    Hi Eric,
    What message do you get when you try to connect?
    Cheers!

  • It doesn't recognise my password for wifi. Unable to connect. Tried ressitng the network,changed the wap settings,nothing. Pswd is 9 characters. MacBook

    iPad 2 doesn't recognise my password for wifi. Unable to connect. Tried resetting the network,changed the wap settings,nothing. Pswd is 9 characters. MacBook and iPhone accepts the password, not my ipad 2

    Hey brainmasala,
    Thanks for using Apple Support Communities.
    Sounds like you are not able to connect to a Wi-Fi network with your iPad. This article has a section for Unable to connect to a Wi-Fi network and the second article is the recommended network settings. If after these it still has the same issue you may want to restore the device to factory settings.
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/TS1398
    iOS and OS X: Recommended settings for Wi-Fi routers and access points
    http://support.apple.com/kb/HT4199
    Use iTunes to restore your iOS device to factory settings
    http://support.apple.com/kb/HT1414
    Have a nice day,
    Mario

  • Hello my iphone 3g can not connect to home network via wifi

    Hello to all, with my iphone 3g can not connect to home network via wifi. This only happens if I apply protection to the network. Unprotected my Iphone connects fine. Obviously the password to write error-free. I can not figure out what depends on this factor, however, another iphone connects fine. Help me please.

    I have a similar,but slightly different problem. My iphone 4 recgonizes my home wifi and shows it under Settings, but will not access it, no signal shown, just 3G.  It will access other wifi signals.  My wife's iphone works fine, as does an ipad and macbook.  This is new for my iphone, about 2-3 days.
    Help!  I reset network settings and rebooted the router (Apple), no avail

  • Hello, I'm trying to connect my new TiVo XL4 box to my home network via an ethernet cable connection to my Airport Express but the TiVo box is not seeing the network. I have a green light emanating from the Airport Express so it is connected. Plz advise.

    Hello, I'm trying to connect my new TiVo XL4 box to my home network via an ethernet cable connection to my Airport Express but the TiVo box is not seeing the network. I have a green light emanating from the Airport Express so it is connected. Please advise.

    If you have not already done so, I suggest that you temporarily disconnect the Ethernet cable from the AirPort Express that goes to the Tivo box.
    Instead, turn off the wireless on a laptop and connect the laptop to the Ethernet port on the Express. See if you can get an Internet connection on the laptop.
    If you still cannot get an Internet connection on the laptop, try another Ethernet cable that you know is working correctly.
    Post back on your results.

  • TS1398 My ipad will not connect to other wifi networks. It has connected to my main home network but will not connect to the booster network in my home (it has previously!) It will also not connect to other networks outside my home.

    Hi
    I just got new router and had to reset my network settings on IPad. Since then, my ipad will connect onto the main home network but will not attach to my extension booster (netgear) which is linked to the home network. It will also not attach to networks outside my home that it has previously worked with. i have reset the settings again, powered off and on again, updated to the latest IOS update, but nothing is working. Please help, as I can only use wifi in a few rooms in my house and i do not have 3G on my my ipad.

    Did you try forgetting the network and starting all over again?
    Settings>WiFi>Network Name>Tap the blue arrow>Forget this Network. Restart your iPad and then try joining again.
    Try rebooting your router. Even though everything else may be connecting to your Network, it might help with the iPad. Unplug the router for about 30 seconds and then plug it in again.
    Reset Network settings on the iPad?
    Settings>>General>Reset>Reset Network Settings. You will have to start all over again, Tap WiFi in the settings, find your network and enter the password.

  • I am having trouble connecting to my in-home internet via wireless router. It says it is connected, but when I try to open email, no connection is found. This also occurs for Safari and Facebook. I am connected by Charter Cable.

    I am having trouble connecting to my in-home internet via my wireless router. The IPad says I'm connected to the router, but I am unable to receive email, Facebook and Safari. I run through Charter Cable.  This only occurs on my IPad. My desktop works fine.

    Although it may ultimately be necessary to perform a Factory Default Reset on the AirPort Extreme and start over with a new configution, we can first try to see if things will work with the existing settings on the device.
    Push the reset button (if present) on the cable modem
    Power off the modem by pulling the power cable
    Remove the internal battery from the modem (if easily accessible)
    Power off the AirPort Extreme and every other device on the network....order is not important
    Wait at least 20 minutes....longer is better
    Re-install the battery in the modem if it was removed previously
    Make sure that the Ethernet cable from the modem is connected to the WAN port (circle of dots icon) on the AirPort Extreme
    Power up the modem and let it run 4-5 minutes buy itself
    Power up the AirPort Extreme and let it run 4-5 minutes
    Then power up each other network device one at a time about a minute apart
    Check for a good Internet connection on the network with all devices
    If still no luck, you will need to perfom a Factory Default Reset on the AirPort Extreme as follows:
    Pull the power plug from the back of the AirPort Extreme
    Hold in the reset button and keep holding it another 8-10 seconds while you simultaneously plug the power back in to the AirPort Extreme
    Release the reset button and allow 25-30 seconds for the AirPort Extreme to restart to a slow, blinking amber light
    Then open AirPort Utility end reconfigure the AirPort Express again.

  • Can not access home network via ipod touch, password entered  not accepted

    Can not access home network via ipod touch, password entered not accepted
    Trying to help my son set up his ipod touch to connect to the network and the password I entered is not accepted.
    1. Which password is required? I entered the password I use for logging into my router
    2. The home network is recognized, when selected it requires a password to be entered, but I am just not sure what password it is looking for to connect.
    I have not been able to find any information on this subject

    jersey0904, Welcome to the discussion area!
    You need to enter the wireless encryption password... not the administrative password for the router.

  • Problems accessing home network via FTP

    I get a -50 error when I try to FTP thru my company's wired Ethernet network to my home network via the "Connect to Server" command in the Finder.
    However, I can connect with my home network using FileZilla thru the same (wired) network.
    And I can connect to my homework via my company's wireless network from the Finder.
    Any ideas what might be blocking me from FTP'ing to my home network via the Finder and thru the wired network, and how to resolve?

    At least a partial answer.
    If I use the command FTP://username@IP Address, I'm able to connect. But I don't have to use my username with wireless.

  • I am unable to connect to my RackSpace Windows Server via ARD. I have added a computer entering the ip address, username, and password but I can't establish a connection. I am missing a setting or to step that is different in ARD?

    I am unable to connect to my RackSpace Windows Server via ARD. I have added a computer entering the ip address, username, and password but I can't establish a connection. I am missing a setting or to step that is different in ARD?

    ARD only works with Windows computers if the Windows computer is running VNC server software.  Even then it can only control and observe.  Do you have this installed?

Maybe you are looking for