Unable to connect to an airport extreme 802.11n wifi using airport utility

I have an Airport Extreme 802.11N Wi-Fi, i connect it to my cable router and i can access the internet using the default setting on the WIFI.
However the status light is blinking yellow.
I try to use the Airport utility to connect to the Airport Extreme however i am unable to connect.
The error message as follows" An error occur while trying to access the apple wireless device. Make sure your network connection is valid and try again"
I know that i am connect to the Airport Extreme Wi-Fi, i can browse the internet but i need to access the device to change the security and SSID name etc.
Can anyone help.

Whats the planned topology supposed to look like. What is the status of each router now?

Similar Messages

I bought the Airport Extreme 802.11n Wifi

I bought the Airport Extreme 802.11n Wifi from the Apple store in West Edmonton Mall Canada got to the airport, customs scanned the box (which was unopened) and they got a dangerous chemicals hit on the unit. No need to say what else happened there after, i was skinned inside out, body search, drill with the 21 questions and on top that they want to know if i have any ties with any terrorist organizations.
Why would this device give off such a reading?

It doesn't.
The box may have been handled by someone with unclean hands. Or, their security equipment may have been miscalibrated. Or, they're just incompetent. Don't you feel safe?

WDS networking issue - Airport Extreme (802.11n) and remote Airport Express

*Background Info:*
Airport Extreme 802.11n (Fast Ethernet)
Version: 7.2.1
Wireless Mode: Participate in a WDS network (set as main)
Network Name: @Home
Wireless Security: WPA/WPA2 Personal
Channel: 1
Airport Express
Version: 6.3
Wireless Mode: Participate in a WDS network (set as remote)
Network Name: @Home
Wireless Security: WPA/WPA2 Personal
Channel: 1
Radio Mode: 802.11b/g compatible
Connect Using: AirPort (WDS)
Connection Sharing: Off (Bridge Mode)
Issue
Please help as I'm having issues with my WDS network. I've setup using both the wizard and manual and also hard reset on both units to setup again but cannot get them both to communicate to one another. Both units are showing green LED under their configuration. For my last attempt, I've tried adding the Airport ID (MAC) of the Airport Express to the Access Control and also DHCP Reservations on the Airport Extreme but still no luck.
The Airport Express (setup as remote) does not even show up in the Airport Extreme's Summary as Wireless Clients. In the WDS tab, the Airport Extreme is set up as WDS main, Allow wireless clients box checked and WDS Remotes has the Airport Express' AirPort ID in the list. On the Airport Express, WDS is set up as remote, with Allow wireless client box checked and the Airport ID of the Airport Express in the WDS Main.
I can connect clients to both units. Both units are configured using the same Network Name and have the same WPA/WPA2 security key. The Airport Extreme (main) however is connected to my broadband so any devices or clients connected to it are able to get outside. Connected devices or clients are assigned IP address via DHCP with IP 10.0.x.x. If wifi devices or clients connect to the Airport Express (remote) they are assigned a completely different IP addresses 169.254.x.x, they are not able to browse the internet or talk to other clients connected on the 10.0.1.x network. The Internet Connection configuration on the Airport Express (remote) is Connect Using Airport (WDS) and Using DHCP. I've even tried manually and entered the IP address 10.0.1.199 that I had assigned to the Airport Express from the Airport Extreme and Router Address as IP of Airport Extreme (10.0.1.1).
I think I've tried everything but I'm still having this problem. The remote Airport Express is not extending my existing Airport Extreme network. Any ideas???

Christopher,
This may or may not be helpful, or it may be something you've already tried or are aware of so I apologize if that's the case.
I have been researching ways to set up the Dual Band Network supported by the AEBS and came across your post. I've got an AEBS and (2) AirPort Express set-up currently (AEBS is main and the Express are participating in the WDS as remotes) and I'm trying to configure one of the Express to utilize a 802.11b/g compatible network while the AEBS runs a 5Ghz 802.11n Only network.
AAR, since the AirPort Express are 2.4Ghz 802.11b/g ONLY (no support for 802.11n), you have to be sure to set-up your AEBS first and select "802.11n (802.11b/g compatible)" in the Radio Mode drop-down on the AEBS before you attempt to connect an AirPort Express. The AEBS should be set-up as your "WDS main" and the Express should be set-up as a "WDS remote" for the network you established when you set-up the AEBS.
Bottom line here is the Express won't be seen by the AEBS unless the AEBS is 'looking' in the 802.11b/g 2.4Ghz frequency.
Hope this was helpful.

AirPort Extreme 802.11n WiFi is blinking amber after changing from cable to DSL. Everything works well; but light used to be solid green.

I changed from cable to DSL yesterday. Technician connected the new modem and all is working excellently, except that the light on my AirPort Extreme which used to be a solid green, is now blinking amber. I know this is not right, yet everything else is working well. What's wrong and how can I fix it?

We need to do some troubleshooting to find out why the amber light is blinking, and to do that we need to know what operating system you are using on your Mac or PC.
If you have a Mac, and are not sure what operating system it is using, click the Apple icon in the upper left corner of the screen, then click About This Mac. Post back with the OS X Version number that you see there.

Setting up Time Capsule with existing AirPort Extreme 802.11n and AirPort Express.

I already have and am using an AirPort Extreme 802.11n with an AirPort Express. I want to set up a Time Capsule 802.11n. Which is the best way to configure this?

... Which is the best way to configure this?
The answer depends on what you need the TC to accomplish. If all you need it to do is perform Time Machine backups, simply have it join your existing network in client mode. It would be if it were to connect to your existing router (presumably your Extreme), not through an "extended" wireless network (presumably your Express).
If you need the TC to "extend" your network so as to serve additional wireless clients, you can do that also. Configure it to "extend" the network created by your Extreme.
As you can see it's quite versatile.

Timed Access not working on new Airport Extreme (802.11n).

I bought a new Airport Extreme (802.11n) to use as a router for my network. The network has a mixture of Macs and PCs, using a mixture of wired and wireless connections.
I configured the security settings with on the Airport Extreme to Timed Access. I set the default setting is to No Access.
Three computers are set with "Everyday, Between 8:00am and 11:00pm"; however, when it's 11:00pm, nothing happens. The three computers continue to have access.
I know the MAC addresses I entered are correct. Does anyone know why the Timed Access is not working?

Yes, the printer was initially set the same way it always was on my old router. It used to pop right up on the list. After I switched I was getting communication errors. Ok, new setup, I wasn't worried yet. When I got to the setup window and it a new printer wasn't found I tried updating drivers. No luck. I then used the IPP mode to enter the IP address with the address on the Canon screen. It failed. I then did the same setup telling it which software from the driver list to use. It still could not see it. The odd part is that the Canon can obviously see the router as its LAN setting read active and it is receiving the IP. I have proceeded to play with every setting on the printer and it is back to factory reset. Oh, I should mention that I have also tried to use Canons network setup utility software and it can not find the connection either. So I really think this is a problem within the router. I have seen many complaints about this on other forums, but most were looking to use the usb on the print server. My Airport is nowhere near my printer and I don't want to lose my all-in-one functions. Some think hard lined ethernet is ancient, but it really is a nice setup. Fast and reliable.

How do I connect my Airport Extreme 802.11n to Epson 645 Printer?

I can't figure out how to connect my Airport Extreme 802.11n to my Epson 645 Printer. Can anyone help me? Thanks!

You may want to try reinstalling Mavericks. Airport Utility installed by Mavericks may no longer connect to your older AEBS (though I've not heard that.) Installing the Old AirPort Utility (Version 5.6) on Mountain Lion | frank.is.
Reinstall Lion, Mountain Lion, or Mavericks
     Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
     COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and
     after the chime press and hold down the OPTION key until the boot manager screen appears.
     Select the Recovery HD and click on the downward pointing arrow button.
     Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu.
     Repair the Hard Drive and Permissions as follows.
After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
     Reinstall Lion/Mountain Lion, Mavericks: Select ReinstallLion/Mountain Lion, Mavericks from
     the Utilities menu, and click on the Continue button.
     Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is
                three times faster than wireless.

Not able to see disk connected to AirPort Extreme 802.11n

I just installed my AirPort Extreme 802.11n Wireless Base station. Wireless internet works like a charm, however, I cannot see my external hard disk when it is connected to the base station (amber light blinking and when checking the problem, I am told that "Disk needs repair"). When connecting the hard disk directly to the PC, I have no problem seeing the data. Any tips or tricks out there... ?
AirPort Extreme 802.11n Windows XP

I finally got my 500 GB Western Digital MyBook USB drive to work by reformatting it to HFS+ format.
Of course, before I could do that, I had to copy all my files onto another hard drive. That job took a day to accomplish.
I work with Poser, and have a lot of content installed... We're talking thousands of files.
Once the drive was reformatted to HFS+ format, I copied everything back over. That took another day. Then I connected to the AEBS.
The USB drive was immediately recognized. It was incredibly easy to access the USB drive on my PCs. It required no effort on my part, except to supply the password.
In the end, I've decided this effort is a failure.
The drive is way too slow for my needs. Also, one of my vital Poser utilities (CorrectReference Pro) will not work properly with the USB drive on the AEBS.
I am currently in the process of copying all those files over to two external USB hard drives attached to my other PC.
Then I plan to unmount my 500 GB MyBook drive, and reformat it back to NTFS. I'll let the Notebook PC have it on a direct connection again.
I have a couple "junk" External Hard drives that are 160 GB. Maybe I'll use one of those as an Airport disk...
But I won't be using the Airport disk for anything important. It's too slow.

Connecting AirPort Express to AirPort Extreme 802.11n

The following steps helped me set up an AirPort Express base station connected to a set of wireless speakers with my new AirPort Extreme 802.11n base station. I’m posting this because the process was not entirely intuitive, at least not to me.
I’ll assume you have set up the AP Extreme base station to connect to the internet and run your home network and that you are connected to your wireless network.
Make sure you set-up the AP Extreme base station to broadcast in 802.11n + 802.11b/g modes, i.e. both at once. You will also have to check he setting that allows the newtork to be extended.
Reset the AP Express base station so that in runs on the factory defaults by pressing the reset button with a paper clip. Wait for it to completely restart.
Launch the AirPort Utility. You should see both your AP Extreme and AP Express base stations in the left hand column. Click on the AP Express base station you just reset. When it asks to switch wireless networks do so. Then hit continue.
On the next screen select “Connect to my current wireless network” option and hit continue.
On the following screen select the “Extend the range of my AirPort Extreme or AirPort Express network” and hit continue. Do NOT select the “Join my wireless network” option even though it says this is how you connect to wireless speakers. This is the part that was not obvious to me. When I tried this the AirPort Express base station flashed orange and wouldn’t connect despite waiting 30 minutes.
Chose the network you wish to extend from the drop down menu. My keychain supplied the password for the network.
Give your base station a name and hit continue.
Select the main base station in the list provided. This is the one connected to the internet and hit ok.
The Airport Utility software will configure the network to accept the AirPort Express base station.
Now all that’s left is to connect your wireless speakers to the AirPort Exppress base station. You can now play music through AirTunes while being connected to your fast 802.11n network.

I recently setup an Airport Express in conjuction with my Extreme Base Station. I'm not really understanding how this method enables 802.11n connection speeds (via Base Station) to the internet and also allow streaming music through the Express at 802.11b/g. It's my understanding that if you want to be able to access the internet AND stream music at the same time the Express needs to join the network. In order for the Express to join the network (able to recognize the Base Station)...the Base station needs to be changed from 802.11n only to 802.11n (802.11b/g compatable)....which essentially means your connecting to the internet at 802.11b/g. If your wanting to keep 802.11n only on the base station...you would have to create a seperate network via the Express to stream music. What this means is you CANNOT access the internet and stream music at the same time. You would have to manually change Airport in the taskbar to do one or the other.
Am I off base here? If I am missing something please let me know...because it would be great to be able to connect to the internet at 802.11n only with a multi-case rate set to 23Mbps vs. the 11Mbps (maximum) of the 802.11b/g compatable option.
I guess what is confusing me is that my setup is basically the same as what was described above..minus having the "Extended Network" being enabled. How does extending the network change things?

Help needed connecting Iomega Minimax Ext HDD to Airport Extreme 802.11n

Would appreciate if someone can help me with the following task. After researching and trying several things, I have not succeed in resolving the issue.
I want to connect a Iomega MiniMax Ext HDD (for Mac) to my (Airport Extreme 802.11n + Time Capsule) box using the USB port at the back of my Airport Extreme. Then I want to access the Ext HDD wirelessly as a drive on my Macbook (snow leopard OS). I was told this was possible at the Apple Store...but have failed so far.
Any suggestions so far

Hello smitra. Welcome to the Apple Discussions!
The following are the basic steps for sharing an external USB drive attached to either an 802.11n AirPort Extreme Base Station (AEBSn) or a Time Capsule (TC):
o Plug the hard disk into the USB port on the back of the base station.
o Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac, and in Start > All Programs > AirPort on a computer using Windows
o Select your base station, and then, choose Manual Setup from the Base Station menu.
o Click Disks in the toolbar, and then, click File Sharing.
o Choose “With a disk password,” or “With base station password” if you want to secure the shared disk with a password, or choose “With accounts” if you want to secure the disk using accounts. If you choose to use accounts, click Configure Accounts, click the Add "+" button, and then enter a name and password for each user that will access the disk. For simplicity, I would recommend using the "With a disk password" option.
o Choose “Not allowed,” “Read only,” or “Read and write” to assign guest access to the disk.
o Select the “Share disks over Ethernet WAN port” checkbox if you want to provide remote access to the disk over the WAN port.
You should now be able to find this drive within Finder under the SHARED category.

I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I h

I'm not sure how to post a message. I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I have an older Airport Express, would it help to install it? would it work best if it was installed in the same room? should it be installed half way in between? Get another Extreme? The Mac Book Pro on the middle floor can see 11 networks in the neighbourhood if that might be causing a problem or would if I installed the Express. Thank for your consideration.

Thanks for your time ... I appologize for the font and colour, I compossed the question in pages and failed to notice the font colour as grey ... there are a variety of computers of various ages so I think it is using a setting that allows both 5G and 2.4 ... the connection to the Airport is thru a cable modem and cable does run throuhout the house ... maybe those hard wires would be a place to look at ... do you think that putting the 'Express' on the second floor might help ... thanks again ...

AirPort Extreme 802.11n Wi-Fi doesn't connect to printer

So, I got the AirPort Extreme 802.11N Wi-Fi connected and working to my cable modem (good times), but now neither computer (PC or Mac) can connect through it to the printer (HP C4280 Aii-in-One) that we connected to the USB port on the back of it.
Any idea what we're doing wrong here? Is there something that needs to be configured within the software of the router?

Work your way through the Apple Troubleshooting Guide to see if that will help get the printer going.
Bear in mind that only the print function will be supported when your device is connected to the USB port on the AirPort Extreme. Scan, copy, fax, maintenance etc. are not supported, so if you need these functions, you will need to connect your all-in-one directly to the computer.
The PC will need to have Bonjour for Windows installed. It's on the CD that came with the AirPort Extreme.

I have a Airport Extreme 802.11n and my T.V. is a panisonic,I keep losing the connection. Anybody have any answers?

I have a Airport Extreme 802.11n and my T.V. is a panisonic,I keep losing the connection. Anybody have any answers?

Plenty of suggestions.. only you can find out which one is correct.
What model AE? What firmware?
Since Panasonic TV is not apple it will use SMB windows type networking.. everything but Apple does.
Are the names in the AE all SMB compatible.. ie short.. max about 20 characters.. no spaces and pure alphanumeric.
Is the security set to WPA2 Personal with a pure alphanumeric password of 10-20 characters.. more is fine if you suffer paranoia but isn't needed.
Fix the wireless channels.. so it doesn't flip flop like a dying fish.
There are only 3 channels for 2.4ghz that do not overlap, 11, 6, 1 although someone suggested 8 works well if you have heaps of interference. If you live in flat/apartment building you have heaps of interference.
Lastly is it stable if the distance is 3M direct line of sight?
If not then get a high power wireless AP and use that instead.

How far away can you connect to the internet from Airport Extreme (802.11n)

How far can i take my Laptop away from Airport Extreme (802.11n) and still have internet connection

According to:
http://www.apple.com/au/airportexpress/
They claim the Extreme has a 45m range:
"Suppose you want to connect to the Internet with your PowerBook in an area that lies beyond the 45 metre range of your AirPort Express or AirPort Extreme Base Station"
Will you be using all N devices? G?, B? or a combination?

Connecting AirPort Extreme 802.11n directly to my Verizon FiOS service

I want to connect my new AirPort Extreme 802.11n directly to my Verizon FiOS service. The ActionTec wireless router supplied by Verizon died, and I bought an AirPort Extreme as a replacement. When I configured the AirPort extreme, it would not connect to the internet. I have read some posts here that indicate I plug my AirPort Extreme into the ActionTec and I am OK, however the ActionTec is dead.
Are there settings for the AirPort Extreme that are unique for going straight to the internet? What am I missing? My FiOS connection is an Ethernet connection- not coax.
Here is the interesting thing- I have an old AirPort Extreme (the round cone shaped model) that I plugged into the Verizon FiOS Ethernet connection. Everything works fine- I have a wireless connection to the internet. I didn't set anything. So my assumption is that I can make the new AirPort Extreme work with the Verizon FiOS.
Any help will be greatly appreciated, as I do not know if I have the strength to go through the Verizon help desk.

Good news! My problem was solved by calling Verizon FiOS support. The service tech said an AEBS can connect straight to the FiOS Ethernet connection. He broke the "lease" on my connection, had me connect the cable from the wall to my WAN slot, and then he "leased" my network connection to my AEBS. Works like butter now.
He said that the Verizon FiOS network "leases" the network connections every 24 hours or so, and had I left my AEBS connected to the network, it would have pushed the new setting down to the AEBS.
Thanks for all of the input.

Unable to connect to an airport extreme 802.11n wifi using airport utility

Similar Messages

Maybe you are looking for