Unable to connect to gateway

Greetings,
2 physical servers db1 and db2.
Installed OVM 3.2.1 on both and VM Manager on a WLS server.
Discovered both OVM installation and was able to create 1 vm guest each. gdb1 and gdb2
I am able to connect to my gateway 192.168.4.1 from the OVM host but not from either of my vm guests.
In the network there is also a SAN, which can be reached on a 192.168.128.0/24 network.
With gdb1 I am able to connect to the SAN management ports. (ping 192.168.128.101)
Al my VNICS are bridged to 1 physical NIC.
But I am unable to connect (ping) from my guest to any 192.168.4.0 addresses.
OVM host network info:
1096943b80 Link encap:Ethernet HWaddr 00:10:18:F6:B3:2A
inet addr:192.168.4.220 Bcast:192.168.4.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:25338 errors:0 dropped:478 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:832940 (813.4 KiB) TX bytes:252 (252.0 b)
bond0 Link encap:Ethernet HWaddr 90:B1:1C:36:45:04
inet addr:192.168.4.20 Bcast:192.168.4.255 Mask:255.255.255.0
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:296281 errors:0 dropped:0 overruns:0 frame:0
TX packets:284149 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:150451123 (143.4 MiB) TX bytes:118921067 (113.4 MiB)
eth0 Link encap:Ethernet HWaddr 90:B1:1C:36:45:04
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:296281 errors:0 dropped:0 overruns:0 frame:0
TX packets:284149 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:150451123 (143.4 MiB) TX bytes:118921067 (113.4 MiB)
Interrupt:16
eth1 Link encap:Ethernet HWaddr 90:B1:1C:36:45:05
inet addr:192.168.128.20 Bcast:192.168.128.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:18430 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1445112 (1.3 MiB) TX bytes:830 (830.0 b)
Interrupt:17
eth2 Link encap:Ethernet HWaddr 00:10:18:F6:B3:2A
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5755 errors:0 dropped:5528 overruns:0 frame:0
TX packets:12697 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:633954 (619.0 KiB) TX bytes:813136 (794.0 KiB)
Interrupt:48
bridge name bridge id STP enabled interfaces
1096943b80 8000.001018f6b32a no eth2
vif7.0
vif7.1
vif7.2
vif7.3
vif7.4
What am I missing here?

Just to clarify
2 physical
OVS1 (192.168.4.20)
OVS2 (192.168.4.22)
2 virtual
DB1 (192.168.4.120)
DB2 (192.168.4.122)
Configured as:
OVS1 (DB1)
OVS2 (DB2)
Your steps:
DB1 > DB2 good
OVS1 > OVS2 good
OVS1 > gateway good
DB1 > OVS1 or OVS2 bad
Please try this:
DB1 > OVS1 (eth0)
DB1 > OVS1 (bond0)
If eth0 = bad , do tcpdump on eth0 and look for ICMP request/response.
Same thing for bond0.
Post results.

Similar Messages

  • While Configuring Siebel Server we are getting "Unable to Connect to Gateway server" error in siebel 8.2.2.14

    Hi
    While Configuring Siebel Server we are getting "Unable to Connect to Gateway server" error in siebel 8.2.2.14
    Our OS is windows 2008 R2 64 bit,Orcale client is 11g 32 bit and Oracle DB is in 11g.We are also able to connect to DB using ODBCSQL.
    Please help.
    Regards
    Shuvendu

    Hello Shuvendu,
    Thanks for using Oracle Communities.
    About your error, there could be many reasons, To start with, please have following knowledge article to know possible reasons.
    C028: "Unable to Connect to the Siebel Gateway Name Server" Logged By Configuration Wizard (Doc ID 1391312.1)
    I hope it helps.
    Best Regards,
    Chetan
    P.S. If any one of the provided responses has been correct or helpful it would be great if you could mark them as appropriate.

  • C7 Social: Unable to connect to Gateway!!!

    Hello All,
    When i'm trying to use Social client in C7 getting the message "Unable to connect to Gateway".  It was working fine for some days. Any idea why this issue is occurring?? How to overcome from this??
    Thanks,
    Abhilash.

    Hi,
    Please clarify me the following.
    You specified the login name as 'SADMIN'. Is this the login id, that you used for your Operating System? "Entered name account authentication gateway server name" expects you to enter the NT login, not the DB login.
    You may also expected to specify your network name, if your login id is specific to a network. e.g Oracle\Rajkumar assuming that Oracle is your network and Rajkumar is the user name.
    You may not expected to have the DSN created, as Gateway may not be interested in knowing which DB you are connected to. And you neither enter the 'DB name' anywhere in the 'Gateway Server Configuration', if my understanding is right.
    Please confirm.
    Below pages are for reference (not directly relevant to your question):
    http://docs.oracle.com/cd/B40099_02/books/SiebInstWIN/SiebInstCOM_Prep18.html
    Bookshelf v8.0: Requirements for Siebel Gateway Name Server Installation and Configuration
    Thanks.
    Regards,
    Rajkumar Raju

  • Netlet fails: "Unable to connect to Gateway: default:443"

    i have installed the portal 3.0 sp4, MAP and HP for sp4.
    when using netlet, it tells me: "Unable to connect to Gateway: default:443"
    the platform.conf file contains the right gateway name.
    why does the netlet uses default:443 instead of the right gateway name and port?
    thnx, thomas

    after reinstalling the server and the gateway, i face the same problem again, but i found out, that the error only occurs when the anonymous desktop is enabled.
    logging in using ldap authentication, everything works; but logging in, using the anonymous desktop, and then loging in at the login-chanel using ldap-authentication, the error occurs, when using Netlet.
    looking at the install logs, i found out that the sp4 wasn't able to update the "iwtGateway-netletproxy-port" and the "iwtNaming-sessionURL" attributes;
    could one of this be respobsible for the failure ?
    has anyone an idea, how to solve the problem ?
    thnx, thomas

  • Netlet - unable to connect to gateway

    Issue with Netlet.
    Trying to define the following rule so non-browser application can do
    http requests over secure tunnel:
    WebTest|null|false|30011|<host>|80
    (where <host> is the relevant webserver)
    Getting the following error:
    Unable to connect to Gateway: default:443
    Any assistance greatly appreciated.

    It seems that this problem is stemming from the variable "WT.gateway"
    (stored in the com.iplanet.portalserver.session.Session object) being set
    to "default". This causes the applet parameters of the Netlet to be
    incorrect. The "remoteHost_x" parameter is being taken literally and the
    Netlet is trying to connect to default:443.
    In my example, the applet tag looks as follows:
    <html>
    <head>
    <HEAD><TITLE>Netlet</TITLE></HEAD>
    <script language=javascript>
    var needToSleep = true;
    </script>
    </head>
    <BODY TEXT="#000000" BGCOLOR="#FFFFFF">
    <p><applet
    codebase="https://algol.solnet.com.au:443/http://algol.solnet.com.au:8080/netlet"
    archive="ips_netlet.jar" code="SServer.class" width=1 height=1 MAYSCRIPT>
    <param name="cabbase" value="ips_netlet.cab">
    <param name="configURL"
    value="https://algol.solnet.com.au:443/http://algol.solnet.com.au:8080/NetletConfig">
    <param name="resourcesURL" value="/NetletConfig?func=loadResources">
    <param name=listenPort_0 value=8000>
    <param name=remoteHost_0 value=default>
    <param name=remotePort_0 value=443>
    <param name=serverPort_0 value=8080>
    <param name=serverHost_0 value=algol.solnet.com.au>
    <param name=listenPort_1 value=30011>
    <param name=remoteHost_1 value=default>
    <param name=remotePort_1 value=443>
    <param name=serverPort_1 value=80>
    <param name=serverHost_1 value=david.mel.solnet.com.au>
    <param name=sessionID
    value=43345sdafxcspdbliqvfxipuglbqoqr14sp5r6@[email protected]@8080@/UbyqraGrfg>
    <param name=numParms value=2>
    <param name=doPortWarning value=true>
    <param name=netletKeepAliveInterval value=0>
    </applet>
    </body>
    </html>
    David Broeren wrote:
    Issue with Netlet.
    Trying to define the following rule so non-browser application can do
    http requests over secure tunnel:
    WebTest|null|false|30011|<host>|80
    (where <host> is the relevant webserver)
    Getting the following error:
    Unable to connect to Gateway: default:443
    Any assistance greatly appreciated.

  • Unable to connect siebel gateway name server during configuration enterprise server

    Hi,
    when I try to configure Siebel enterpise after entering the port of the gateway server name I get the following error: "Unable to connect gateway server name".
    I perform the following steps:
    1) Configuration Gateway Server Name
         Entered port TCP/IP = 2320
         Enable automaticaly start server gateway name server
         Show pop up "Configuration siebel succesful"
    2) Configuration Enterprise Server
         Entered name account authentication gateway server name = SADMIN
         Entered passoword account authentication gateway server name = SADMIN
         Entered name host gateway server name = VDIMTNSIEBEL01 (name my machine)
         Entered port TCP/IP gateway server name = 2320
         show pop up error : "Unable to connect gatawey server name"
    I can not find the log file in order to understand the issue.
    When I try to connect to the gateway from the browser with the url
    vdimtnsiebel01:2320 I get this screen mode:
    ???@??????? ?????????? ????????QÈ  ??? ??????????? ??? ??? ? ?h????
    and writes this log in the file "C:\siebel\8.1.1.0.0\ses\gtwysrvr\log\NameSrvr.log
    SisnapiLayerLog Error 1 0000001151c810a0:0 2013-06-25 10:11:27   4980: [SISNAPI]: Rx msg len=0 peer=VDIMTNSIEBEL01.ISCVDI.LOCAL avail=325 Hello expected session=13
    474554202F66617669636F6E2E69636F
    20485454502F312E310D0A486F73743A
    207664696D746E73696562656C30313A
    323332300D0A557365722D4167656E74
    3A204D6F7A696C6C612F352E30202857
    696E646F7773204E5420362E313B2057
    4F5736343B2072763A32312E30292047
    65636B6F2F3230313030313031204669

    Hi,
    Please clarify me the following.
    You specified the login name as 'SADMIN'. Is this the login id, that you used for your Operating System? "Entered name account authentication gateway server name" expects you to enter the NT login, not the DB login.
    You may also expected to specify your network name, if your login id is specific to a network. e.g Oracle\Rajkumar assuming that Oracle is your network and Rajkumar is the user name.
    You may not expected to have the DSN created, as Gateway may not be interested in knowing which DB you are connected to. And you neither enter the 'DB name' anywhere in the 'Gateway Server Configuration', if my understanding is right.
    Please confirm.
    Below pages are for reference (not directly relevant to your question):
    http://docs.oracle.com/cd/B40099_02/books/SiebInstWIN/SiebInstCOM_Prep18.html
    Bookshelf v8.0: Requirements for Siebel Gateway Name Server Installation and Configuration
    Thanks.
    Regards,
    Rajkumar Raju

  • Unable to connect to Gateway Name Server while config Siebel Server

    I installed Siebel 8.1.1.11.0 on RHEL 32-bit. I did configuration as following.
    Install 32-bit Oracle Client and config TNS.
    Install and config Gateway and Enterprise.
    Install Siebel Database.
    Use stop_ns, start_ns and list_ns to restart and ensure Gateway running.
    Run CreateSiebSrvrEnvScript to generate Env file.
    Modify /siebel/8.1.1.11.0/ses/siebsrvr/siebenv.sh. Change ODBCINI=/siebel/8.1.1.11.0/ses/gtwysrvr/sys/.odbc.ini.
    Source siebenv.sh.
    export LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/home/oracle/product/11.2.0/client_1/lib
    Config Siebel Server. While enter info of Gateway, enter SADMIN as account, rhel (configed in /etc/sysconfig) as host name and port = 2320. Then it prompt "Unable to connect to the Siebel Gateway Name Server".
    Any step missing to config it?
    Thanks

    The siebenv.sh file located in the Gateway directory from a 8.1.1.11 installation doesn't have the enviromentt variable SIEBEL_UNIXUNICODE_DB, which i do have in the siebenv.sh from my 8.1.1.0 installation. Add the following line to the siebenv.sh located in the gateway directory (/siebel/8.1.1.11.0/ses/gtwysrvr in my installation):
    SIEBEL_UNIXUNICODE_DB=ORACLE; export SIEBEL_UNIXUNICODE_DB
    Be sure that this variable is set BEFORE you start the gateway and everything should work.
    PS- You also need the Oracle enviroment varibles set before you start the gateway. ORACLE_HOME should be pointing to your 32bit client.
    Cheers!

  • Remote Desktop Connection Client 9.3.9600 unable to connect to Server 2012 RDS via Gateway

    Hi,
    I have a Windows Sever 2012 R2 RDS environment with two Gateways servers configured in high availability mode (RD Web Access, RD Gateway, RD Connection Broker roles installed) and four Windows Server 2012 R2 RDS Session Hosts. The servers are all running
    the most recent public server updates. With this configuration I when connecting externally using a Windows 7 computer with the older Remote Desktop Connection client (6.1.7601) I am able to connect without any problems however when I try connecting with a
    newer client from a computer running Windows 8.1 and the 9.3.9600 client I am unable to connect. 
    At the moment a NAT rule is configured to pass 80/443 traffic to only one of the RDS gateway servers, I've removed our load balancer from the configuration for the moment to reduce the complexity. 
    No error is generated by the client when it tries to connect it just stops trying to connect after a while.
    On the Gateways servers event logs for 
    Things I have looked into so far.
    - I've double and triple checked the RDS configuration and checked it against one of my other clients configurations that is working and they are identical. 
    - Connecting from an older client version works fine.
    I'm not sure what else can be checked does anyone have any ideas?

    Hi,
    1. What entries are you seeing in the RD Gateway's log?  Event Viewer\ Applications and Services Logs\ Microsoft\ Windows\ TerminalServices-Gateway
    2. How come you are not forwarding UDP port 3391 in addition to TCP port 443?  It should work without UDP, but you will not have UDP support which is one of the benefits of RDP 8.0/8.1.
    3. Are there any non-default group policy settings being applied to the servers and/or client PCs?  To be clear, I'm asking if any changes have been made to the default local and domain security policies, group policy objects, new GPOs that may have
    been added, etc., that are applicable to the servers and or client PCs.
    -TP

  • CO28: Unable to connect to Siebel Gateway Name Server

    Hello.
    I'm trying to install Siebel on a WinXP machine to familiarize myself with the Case Management module from Siebel. I have tried many times, installing and uninstalling software. I keep getting this error message when configuring a new Enterprise. "CO28: Unable to connect to Siebel Gateway Name Server".
    I've shortened the hostname and removed dashes as prescribed in Siebel Bookshelf.
    I've always made sure the ODBC System DSN is working and authenticating correclty.
    Netstat shows gtwyns listening on 0.0.0.0:2320
    What am I missing?????

    Here's the log contents from sw_cfg_util.log:
    2021 2009-05-21 12:52:03 0000-00-00 00:00:00 -0700 00000000 001 003f 0001 09 sw_cfg_util 2992 1704 C:\sba8123\siebsrvr\log\sw_cfg_util.log 8.1.1 [21112] ENU
    GenericLog     GenericError     1     000000024a150bb0:0     2009-05-21 12:52:03     Error in transferring input values ,num of arrays incorrect 0, expected : 1
    GenericLog     GenericError     1     000000024a150bb0:0     2009-05-21 12:52:03     TransferInputsToValues returned error:3611539 to SetControlValues
    GenericLog     GenericError     1     0000031a4a150e34:0     2009-05-21 12:52:28     NSS - ErrCode 4597527 SysErr 0
    GenericLog     GenericError     1     0000031b4a150e34:0     2009-05-21 12:52:29     NSS - ErrCode 4597527 SysErr 0
    GenericLog     GenericError     1     0000031b4a150e34:0     2009-05-21 12:52:29     Validation failed : C028: Unable to connect to the Siebel Gateway Name Server 嗭粑୩୩୩୩୩୩୩
    GenericLog     GenericError     1     0000031b4a150e34:0     2009-05-21 12:52:29     ValidateFailed for Gateway Name Server TCP/IP Port, error : C028: Unable to connect to the Siebel Gateway Name Server 嗭粑୩୩୩୩୩୩୩
    GenericLog     GenericError     1     0000031b4a150e34:0     2009-05-21 13:18:49     Error in transferring input values ,num of arrays incorrect 0, expected : 1
    GenericLog     GenericError     1     0000031b4a150e34:0     2009-05-21 13:18:49     TransferInputsToValues returned error:3611539 to SetControlValues
    GenericLog     GenericError     1     0000031c4a150e34:0     2009-05-21 13:18:52     NSS - ErrCode 4597527 SysErr 0
    GenericLog     GenericError     1     0000031c4a150e34:0     2009-05-21 13:18:52     Validation failed : C028: Unable to connect to the Siebel Gateway Name Server 嗭粑୩୩୩୩୩୩୩
    GenericLog     GenericError     1     0000031c4a150e34:0     2009-05-21 13:18:52     ValidateFailed for Gateway Name Server TCP/IP Port, error : C028: Unable to connect to the Siebel Gateway Name Server 嗭粑୩୩୩୩୩୩୩

  • Unable to connect to siebel gateway name server .

    unable to connect to siebel gateway name server .
    erro log:
    [TCPIP-client] failed to resolve hostname: siebel82 (err=852198 | Internal: gethostbyname_r ()failed with error. (%sysError))
    //1
    commonutil ValidateSiebelGateway sadmin password 192.168.0.82:2320 // return true
    commonutil ValidateSiebelGateway sadmin password siebel82:2320 // return false
    commonutil ValidateSiebelGateway sadmin password siebel82.cc:2320 // return false
    //2
    [oracle@siebel82]$ ping siebel82
    PING siebel82.cc (192.168.0.82) 56(84) bytes of data.
    64 bytes from siebel82.cc (192.168.0.82): icmp_seq=1 ttl=64 time=0.038 ms
    64 bytes from siebel82.cc (192.168.0.82): icmp_seq=2 ttl=64 time=0.050 ms
    //3
    [oracle@siebel82]$
    ping siebel82.cc
    PING siebel82.cc (192.168.0.82) 56(84) bytes of data.
    64 bytes from siebel82.cc (192.168.0.82): icmp_seq=1 ttl=64 time=0.036 ms
    64 bytes from siebel82.cc (192.168.0.82): icmp_seq=2 ttl=64 time=0.050 ms
    //4
    [oracle@siebel82]$ nslookup siebel82.cc
    Server:          192.168.0.82
    Address:     192.168.0.82#53
    Name:     siebel82.cc
    Address: 192.168.0.82
    //5
    [oracle@siebel82]$ nslookup siebel82.cc
    Server:          192.168.0.82
    Address:     192.168.0.82#53
    Name:     siebel82.cc
    Address: 192.168.0.82
    //6
    [oracle@siebel82 bin]$ uname -a
    Linux siebel82.cc 2.6.32-100.34.1.el6uek.x86_64 #1 SMP Wed May 25 17:46:45 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux
    //7
    Installed Top-level Products (2):
    Siebel Enterprise Server 8.2.2.0.0
    Siebel Enterprise Server - enu 8.2.2.0.0
    Thank you for any tips.

    check the connect string in eapps.cfg

  • "UNABLE TO CONNECT GATEWAY PLEASE TRY AGAIN LATER"...

    Hi
    when i tried to cannect facebook in social i m getting "UNABLE TO CONNECT GATEWAY PLEASE TRY AGAIN LATER" i restore factory setting but problem not solve my othr apps is working fine (maps ovi store,ovi music) but ovi social is not workinh please help me to solve this issue

    What did you do? Plz let me know. I am facing the same problem.

  • C028: Unable to connect to Siebel Gateway Name Server during Siebel Server

    Hi,
    I'm getting above error during Siebel Server Configuration when I run the Configuration Wizard
    C028: Unable to connect to Siebel Gateway Name
    Gateway name Server is up and running on same machine, Database Server is up and running on other machine and Application server machine can make connection to database machine through Oracle database client all Oracle net configuration entries are properly added in the Client TNSNAMES.ora file, the Siebenv.sh contain all necessary entries including ORACLE_HOME, bin path and lib32 path along with proper Oracle_sid entry and also I'm giving proper gateway name server credentials i.e of sadmin.
    Here are the logs of the gateway name server
    File Name:= NameSrvr.log
    DBCLog DBCLogError 1 000000114dc910be:0 2011-05-10 18:26:32 523 80
    GenericLog GenericError 1 000000114dc910be:0 2011-05-10 18:26:32 (secmgr.cpp (2679) err=4597538 sys=0) SBL-SEC-10018: 523 80
    GenericLog GenericError 1 000000114dc910be:0 2011-05-10 18:26:32 (secmgr.cpp (2735) err=4597527 sys=0) SBL-SEC-10007: The password you have entered is not correct. Please enter your password again.
    GenericLog GenericError 1 000000114dc910be:0 2011-05-10 18:26:32 (client.cpp (309) err=4597527 sys=0) SBL-SEC-10007: The password you have entered is not correct. Please enter your password again.
    SisnTcpIp SisnSockError 1 000000114dc910be:0 2011-05-10 18:26:32 530: [TCPIP-server] recv() failed for sd=-1 (err=9 | Bad file number)
    SisnTcpIp SisnSockError 1 000000114dc910be:0 2011-05-10 18:26:32 530: [TCPIP-server] send() failed for sd=-1 (err=9 | Bad file number)
    File Name:- nameserver_audit.log
    Timestamp Record Type Host Name ProcId Client Name User Name Key Name Value
    2011-05-10 17:09:16 FailedLogin Siebelmachine 958544 java SADMIN
    Kindly help me in identifying where I'm making the mistake as I've configured all necessary thing needed for Allpication Server Configuration upto best of my knowledge. Your help will be highly Appriciated.
    Regards,
    Abbasi

    Abbasi,
    This error message can be related with Doc ID 751784.1, here is the workaround suggested:
    1. Stop all Siebel Enteprise components (Gateway/Siebel Server/Web Server)
    2. Copy SIEBEL_ROOT/siebsrvr/IVSE.LIC to SIEBEL_ROOT/gtwysrvr/
    3. Restart the Siebel Enterprise components
    4. Use srvrmgr to confirm a connection to the Gateway Name Server can be made without error e.g.
    srvrmgr /g gateway1 /e enterprise1 /u sadmin /p sadmin
    If successful a message such as "Connected to 1 server(s) out of a total of 1 server(s) in the enterprise" will be displayed.
    Hope it helps.
    Wilson

  • C028:unable to connect to siebel gateway name server

    Hi Siebel Guru,
    I am facing issue with C028:unable to connect to siebel gateway name server when i configuring a new enterprise for gateway name server.
    please help me out to sole this issue ASAP.
    Regards
    Prabhat

    HI
    I configured my gateway server with default port 2320.
    and my gateway server up and running mode.
    my port also listening.
    netstat -na | grep 2320
    tcp 0 0 0.0.0.0:2320 0.0.0.0:* LIST EN
    -bash-3.1$ list_ns
    started at Thu May 21 01:00:39 2009, pid: 5834, autostart: no
    -bash-3.1$ start_ns
    service is already running
    started at Thu May 21 01:00:39 2009, pid: 5834, autostart: no

  • C028 unable to connect to siebel gateway name server while enterprise installation

    Dear All,
    I am getting this error while setting up an enterprise in the gateway server.The configuration wizard is failing with the error
    "C028 unable to connect to siebel gateway name server"
    Kindly request to assist, the server needs to be delivered on priority
    I checked the gateway..cfg this seems to be fine and the gateway server is up and running.
    The name server log says the following,but the username and password of sadmin is same as configured in DB
    2021 2014-09-04 15:14:20 0000-00-00 00:00:00 +0100 00000000 001 003f 0001 09 GtwyNS 19368 1081086784 /data/siebel/sia811/gtwysrvr/log/NameSrvr.log 8.1.1 [21111] ENU
    DBCLog DBCLogError 1 0000000254084ba8:0 2014-09-04 15:14:20 ㈵″㐴8쾈䃬쯌䀔꼄ࢂ쯌䀔쾨䃬ȁ䀇꼄ࢂ,
    GenericLog GenericError 1 0000000254084ba8:0 2014-09-04 15:14:20 (secmgr.cpp (2679) err=4597538 sys=0) SBL-SEC-10018: ㈵″㐴8쾈䃬쯌䀔꼄ࢂ쯌䀔쾨䃬ȁ䀇꼄ࢂ,
    GenericLog GenericError 1 0000000254084ba8:0 2014-09-04 15:14:20 (secmgr.cpp (2735) err=4597527 sys=0) SBL-SEC-10007: The password you have entered is not correct. Please enter your password again.
    GenericLog GenericError 1 0000000254084ba8:0 2014-09-04 15:14:20 (client.cpp (309) err=4597527 sys=0) SBL-SEC-10007: The password you have entered is not correct. Please enter your password again.
    SisnTcpIp SisnSockError 1 0000000254084ba8:0 2014-09-04 15:14:20 1089268624: [TCPIP-server] recv() failed for sd=-1 (err=9 | Bad file descriptor)
    SisnTcpIp SisnSockError 1 0000000254084ba8:0 2014-09-04 15:14:20 1089268624: [TCPIP-server] send() failed for sd=-1 (err=9 | Bad file descriptor)
    DBCLog DBCLogError 1 0000000354084ba8:0 2014-09-04 15:14:20 ㈵″㐴8
    GenericLog GenericError 1 0000000354084ba8:0 2014-09-04 15:14:20 (secmgr.cpp (2679) err=4597538 sys=0) SBL-SEC-10018: ㈵″㐴8
    GenericLog GenericError 1 0000000354084ba8:0 2014-09-04 15:14:20 (secmgr.cpp (2735) err=4597527 sys=0) SBL-SEC-10007: The password you have entered is not correct. Please enter your password again.
    GenericLog GenericError 1 0000000354084ba8:0 2014-09-04 15:14:20 (client.cpp (309) err=4597527 sys=0) SBL-SEC-10007: The password you have entered is not correct. Please enter your password again.
    SisnTcpIp SisnSockError 1 0000000354084ba8:0 2014-09-04 15:14:20 1104309136: [TCPIP-server] recv() failed for sd=-1 (err=9 | Bad file descriptor)
    SisnTcpIp SisnSockError 1 0000000354084ba8:0 2014-09-04 15:14:20 1104309136: [TCPIP-server] send() failed for sd=-1 (err=9 | Bad file descriptor)
    DBCLog DBCLogError 1 0000000454084ba8:0 2014-09-04 15:14:31 ㈵″㐴8
    GenericLog GenericError 1 0000000454084ba8:0 2014-09-04 15:14:31 (secmgr.cpp (2679) err=4597538 sys=0) SBL-SEC-10018: ㈵″㐴8
    GenericLog GenericError 1 0000000454084ba8:0 2014-09-04 15:14:31 (secmgr.cpp (2735) err=4597527 sys=0) SBL-SEC-10007: The password you have entered is not correct. Please enter your password again.
    GenericLog GenericError 1 0000000454084ba8:0 2014-09-04 15:14:31 (client.cpp (309) err=4597527 sys=0) SBL-SEC-10007: The password you have entered is not correct. Please enter your password again.
    SisnTcpIp SisnSockError 1 0000000454084ba8:0 2014-09-04 15:14:31 1104309136: [TCPIP-server] recv() failed for sd=-1 (err=9 | Bad file descriptor)
    SisnTcpIp SisnSockError 1 0000000454084ba8:0 2014-09-04 15:14:31 1104309136: [TCPIP-server] send() failed for sd=-1 (err=9 | Bad file descriptor)
    Please let me know what else can be checked.Kindly request all to assist me because this server needs to be delivered asap.Let me know if more details is required. Please assist.I checked multiple possibilities even re configuring the gateway server :-( :-( 
    Regards,
    Pramodh

    Hi,
    i have the same problem, i want to use different schemas on db, i have the schema siebel/sadmin and other schema siebelA/sadminA, i'm installing siebel on linux redhat 6.5, and when i'm on Siebel Server Configuration and i write the user and passw sadminA/sadminA i get the error c028 C028 unable to connect to siebel gateway name server, i made the test by sqlplus using sadminA/sadminA and is ok, i made the test configuring to the schema siebel/sadmin and pass, i need to change some for siebel can work with another schema? i'm new here and i dont know if is correct to write my question here.
    Thanks in advance
    I add my gateway.cfg
    [InfraNameServer]
    EnableAuditTrail = FALSE
    [InfraSecMgr]
    SecAdptName = DBSecAdpt
    SecAdptMode = DB
    [DBSecAdpt]
    DBSecAdpt_SecAdptDllName = sscfsadb
    DataSourceName = ServerDataSrc
    DBSecAdpt_PropagateChange = TRUE
    [DataSources]
    ServerDataSrc            = Server
    LDAPSecAdpt              = LDAP
    [ServerDataSrc]
    Docked                   = TRUE
    ConnectString            = DemoEnt_DSN
    TableOwner               = SIEBELA
    DLL                      = sscdo90
    SqlStyle                 = OracleCBO
    MaxCachedCursors         = 16
    MaxCachedDataSets        = 16
    ReverseFillThreshold     = 100
    FileSystem               = /u01/app/siebel81/gtwysrvr/fs
    GatewayAddress           = awsdemo:2320
    EnterpriseServer         = DemoEnt
    CurrentSQLID             = %SQLID%
    MaxCursorSize            = -1
    PrefetchSize             = -1
    ChartServer              = localhost:8001
    ChartImageFormat         = png
    [LDAPSecAdpt]
    SecAdptDllName              = sscfldap
    ServerName                  = $(FQDNName)
    Port                        = $(Port)
    BaseDN                      = $(BaseDN)
    SharedCredentialsDN         = $(SharedCredentialsDN)
    UsernameAttributeType       = $(UsernameAttributeType)
    PasswordAttributeType       = $(PasswordAttributeType)
    CredentialsAttributeType    = $(CredentialsAttributeType)
    RolesAttributeType          = $(RolesAttributeType)
    SslDatabase                 = $(SslDatabase)
    ApplicationUser             = $(ApplicationUser)
    ApplicationPassword         = $(ApplicationPassword)
    HashDBPwd                   = $(HashDBPwd)
    PropagateChange             = $(PropagateChange)
    CRC                         = $(CRC)
    SingleSignOn                = $(SingleSignOn)
    TrustToken                  = $(TrustToken)
    UseAdapterUsername          = $(UseAdapterUsername)
    SiebelUsernameAttributeType = $(SiebelUsernameAttributeType)

  • BIA 7.9.6.1 Unable to connect to Informatica services from DAC

    Hi All,
    As a learning exercise, I have installed the following on a single Windows XP machine (Am aware that Windows XP is not supported for Informatica Service install - but currently have access to only this machine)
    - OBIA 7.9.6.1
    - Informatica 8.6.1 client & services with hotfix 6
    - DAC client & server
    I have created the Repository and Integration services in Informatica PowerCenter and are running in normal mode
    I have configured the DAC as per installation document. I am now trying to configure the DAC Integration Settings for informatica.
    I am unable to register an Integration service or a repository service and get the following errors,
    On testing the Integration Service registration
    Failure connecting to "INFORMATICA_DW_SERVER"!
    And in the log file I find
    SEVERE Thu Nov 12 11:43:54 WST 2009
    ANOMALY INFO::: Error while pinging informatica server using command pmcmd pingservice -sv int_service -d Domain_ASG596138
    MESSAGE:::log\ping.log (The system cannot find the file specified)
    EXCEPTION CLASS::: java.io.FileNotFoundException
    java.io.FileInputStream.open(Native Method)
    java.io.FileInputStream.<init>(FileInputStream.java:106)
    java.io.FileInputStream.<init>(FileInputStream.java:66)
    com.siebel.etl.functional.ReadFileToBuffer.readFileToBuffer(ReadFileToBuffer.java:39)
    com.siebel.etl.gui.data.StaticDatabaseCalls.testServer(StaticDatabaseCalls.java:917)
    com.siebel.etl.gui.data.StaticDatabaseCalls.testInformaticaServer(StaticDatabaseCalls.java:887)
    com.siebel.etl.net.ExecutionPlan.getInformaticaStatus(ExecutionPlan.java:275)
    com.siebel.etl.net.ClientMessageDispatcher$WorkerThread.mBeanRequestInformaticaStatus(ClientMessageDispatcher.java:433)
    com.siebel.etl.net.ClientMessageDispatcher$WorkerThread.consoleMessage(ClientMessageDispatcher.java:224)
    com.siebel.etl.net.ClientMessageDispatcher$WorkerThread.run(ClientMessageDispatcher.java:144)
    On testing the Repository Service registration
    Failure connecting to "INFORMATICA_REP_SERVER"!
    ANOMALY INFO::: Error while pinging informatica repository server
    MESSAGE:::C:\orahome\10gR3_2\bifoundation\dac\log\pmrepConnect.log (The system cannot find the file specified)
    EXCEPTION CLASS::: java.io.FileNotFoundException
    java.io.FileInputStream.open(Native Method)
    java.io.FileInputStream.<init>(FileInputStream.java:106)
    java.io.FileInputStream.<init>(FileInputStream.java:66)
    com.siebel.etl.functional.ReadFileToBuffer.readFileToBuffer(ReadFileToBuffer.java:39)
    com.siebel.analytics.etl.infa.interaction.PmrepInvoker.pmrep(PmrepInvoker.java:100)
    com.siebel.etl.gui.data.StaticDatabaseCalls.testRepositoryServer(StaticDatabaseCalls.java:959)
    com.siebel.etl.gui.data.StaticDatabaseCalls.testInformaticaServer(StaticDatabaseCalls.java:890)
    com.siebel.etl.net.ExecutionPlan.getInformaticaStatus(ExecutionPlan.java:275)
    com.siebel.etl.net.ClientMessageDispatcher$WorkerThread.mBeanRequestInformaticaStatus(ClientMessageDispatcher.java:433)
    com.siebel.etl.net.ClientMessageDispatcher$WorkerThread.consoleMessage(ClientMessageDispatcher.java:224)
    com.siebel.etl.net.ClientMessageDispatcher$WorkerThread.run(ClientMessageDispatcher.java:144)
    Could anyone please suggest what could be the cause of these errors. Any pointers to how to debug this will also be great. Please note I am totally new to Informatica and OBIA.
    Many Thanks,
    Kiran

    HI All,
    I fixed the first part of the issue. Now I am able to connect top the Integration Service. I created system environment variable INFA_DOMAINS_FILE and included the BIN path in PATH variable.
    However unable to connect to the Informatica Repository service. I am getting the follwoing error
    Failure connecting to "INFORMATICA_REP_SERVER"!
    ANOMALY INFO::: Error while connecting to informatica repository server
    MESSAGE:::
    pmrep Connect Error
    =====================================
    STD OUTPUT
    =====================================
    Informatica(r) PMREP, version [8.6.1], build [183.1218], Windows 32-bit
    Copyright (c) Informatica Corporation 1994 - 2008
    All Rights Reserved.
    This Software may be protected by U.S. Patent Numbers 6,208,990; 6,044,374; 6,014,670; 6,032,158; 5,794,246; 6,339,775; 6,850,947; 6,895,471; 7,254,590 and other U.S. Patents Pending.
    Invoked at Thu Nov 12 12:59:16 2009
    [11/12/2009 12:59:25-[REP_12164] Domain-related error: [[PCSF_46008] Cannot connect to gateway to look up service [repo_service]. [FAULT_PCSFTIMEOUTEXCEPTION]].]
    [11/12/2009 13:00:26-[REP_55115] Still trying to connect to the Repository Service [repo_service]. The remaining resilience time is 110 seconds.]
    [11/12/2009 13:00:35-[REP_12164] Domain-related error: [[PCSF_46008] Cannot connect to gateway to look up service [repo_service]. [FAULT_PCSFTIMEOUTEXCEPTION]].]
    [11/12/2009 13:01:37-[REP_55115] Still trying to connect to the Repository Service [repo_service]. The remaining resilience time is 39 seconds.]
    [11/12/2009 13:01:46-[REP_12164] Domain-related error: [[PCSF_46008] Cannot connect to gateway to look up service [repo_service]. [FAULT_PCSFTIMEOUTEXCEPTION]].]
    [11/12/2009 13:02:21-[REP_55112] Unable to connect to the Repository Service [repo_service] since the resilience time is up.]
    [Failed to connect to repository service [repo_service].]
    An error occurred while accessing the repository[Failed to connect to repository service [repo_service].]
    [11/12/2009 13:02:21-[REP_55102] Failed to connect to repository service [repo_service].]
    Repository connection failed.
    Failed to execute connect.
    Completed at Thu Nov 12 13:02:21 2009
    =====================================
    ERROR OUTPUT
    =====================================
    EXCEPTION CLASS::: com.siebel.analytics.etl.infa.interaction.PmrepConnectException
    com.siebel.analytics.etl.infa.interaction.PmrepInvoker.pmrep(PmrepInvoker.java:102)
    com.siebel.etl.gui.data.StaticDatabaseCalls.testRepositoryServer(StaticDatabaseCalls.java:959)
    com.siebel.etl.gui.data.StaticDatabaseCalls.testInformaticaServer(StaticDatabaseCalls.java:890)
    com.siebel.etl.net.ExecutionPlan.getInformaticaStatus(ExecutionPlan.java:275)
    com.siebel.etl.net.ClientMessageDispatcher$WorkerThread.mBeanRequestInformaticaStatus(ClientMessageDispatcher.java:433)
    com.siebel.etl.net.ClientMessageDispatcher$WorkerThread.consoleMessage(ClientMessageDispatcher.java:224)
    com.siebel.etl.net.ClientMessageDispatcher$WorkerThread.run(ClientMessageDispatcher.java:144)
    Please help.
    Thanks,
    Kiran

Maybe you are looking for