Unable to connect to internet-3g connectivity
When ever I try to connect to the internet or any internet related apps, everything just sits there and tries to load forever. The circle besides the signal just keeps rotating. I dont know what the problem is, my 3g settings for APN are correct. Help me out!
Try a Reset [Hold the Home and Sleep/Wake buttons down together for 10 seconds or so (until the Apple logo appears) and then release].
Similar Messages
-
Unable to connect to Internet via Airport Express - 'cannot contact server'
I'm unable to connect to the internet via my Airport Express. I'm using OS 10.3.9, and had the same setup with no problems at a previous address, but with a different modem from the same ISP.
My AE is connected - the light is green - and my mac is connected to the network in Internet Connect. But when I open Safari I get an 'unable to contact server' message.
I've tried rebooting everything (modem, AE, Mac), and leaving modem/AE off for several minutes. Also reset the AE, but to no avail.
The connection works fine via Ethernet cable.
Any ideas?Thanks, I checked out that advice doc (106798), but could not connect to the address (http://17.149.160.49) which is given to test if it's a DNS issue. My ISP says I shouldn't need DNS settings.
The service is PPPoE, and I went into Airport Admin Utility to check if the Airport was configured for this. Under Configure/Internet, I found it was set to 'Ethernet', so changed it to PPPoE. Then when I restarted I got connection status in the bar (and good Airport signal), but status flipped between 'looking for PPPoE host' and 'negotiating PPPoE host', sometimes sticking on one or the other each time I tried rebooting all gear.
Any other ideas? -
Why can't I update or load new apps on my iPhone and iPad. It does not ask me for my password. I tried to sync from my laptop now I am unable to connect to any sites from internet explorer. When I try to update or load any app it tells me it is corrupt
You need to ask Apple for assistance with getting back into your old ID. To do this, click here and pick a method; if that page doesn't list one for your country or you're unable to resolve this issue through the Account Security team, fill out and submit this form.
(118441) -
I have a macbook laptop. When I go to open firefox it opens but when I try to get into a website such as www.yahoo or any other, a menu pops up and says it is unable to connect to the server check your internet connection or if u have fire wall check to see if it is set for firefox to connect. I have never had this problem before. All of a sudden it does not want to work and I need firefox to work.
Hey, Buzz.
You can download the latest version of iTunes supported on Leopard here:
http://support.apple.com/kb/DL1575
I hope that helps. -
I am unable to connect to the interent. At the top of the screen my computer says that I am connected. When I open up Safari there is a pop up that say "Community Toolbar We're sorry, but the Safari browser version you are currently using does not support the community toolbar" and when the Safari page opens up it says "You are not connected to the Internet. Safari can't open the page .... because your computer isn't connected to the Internet." I have tried Network Diagnostics and tried to reset Sfari, empty Cache as well as deleted all of my interent history. I am unable to use Time Machine because I never set it up. If someone knows how to help I would very much appreciate it!!
Some instructions for removing Community Toolbar are available in this thread: https://discussions.apple.com/message/15868085#15868085
-
Unable to connect to internet or print wirelessly on Boot Camp with Windows 7
I recently installed Boot Camp and Windows 7 on my Mac Book Pro with no problems.
A month later, I am unable to connect to internet or print wirelessly.
It states that I am connected to my router.
When I trouble shoot, it cannot find the problem.
My wireless connection and cable connection are fine on the MAC side.
Please help.looks a like a Windows 7 problem. I assume that you can click on the current connection info on the task bar and see a connection to your wireless router? Have you updated your copy of Windows since it was working? I am wondering if it's an update that's applied in Windows which has done something.
-
I am wanting to update iphone to 4.3.3 software. however itunes is telling me it is unable to connect to update server as i am not connect to the internet. yet i clearly am connected... Please help
Looks like I've asked a really old/common question - toonz posted the answer - I've copied it below. Thanks toonz, everything now ok.
Correct AnswerRe: Updating to 1.1.3 02-Feb-2008 23:19 (in response to alibeau)
You can fix this by following the steps in this article:
http://docs.info.apple.com/article.html?artnum=304468
Liked (1) -
I have a 16GB iPod touch that suddenly stopped connecting to the internet last night. Everytime I try to get mail, or access anything with Safari I get a message saying that it can't connect to the server. Also I've plugged it in to my home computer but it won't connect to iTunes either. I haven't updated to iOS8 yet as I didn't have enough space for it and I had planned on deleting all my music files, updating the software and putting whatever music I could fit back on to the device afterward, but now I'm hesitant to do that as I have no way to get any of the files back onto the device. Could this be because I haven't updated to iOS8 yet? I've been having other problems such as apps crashing unexpectedly lately as well, for example my music shuts off randomly and apps such as Twitter and Tumblr and a few others crash on launch. I'm definitely not a genius when it comes to technology by any means, so I have no idea what's causing this problem or how to fix it, any help would be greatly appreciated!
Does the iOS device connect to other networks? If yes that tend to indicate a problem with your network.
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
Since updating my ipad to iOS 6 a few days ago i can't seem to get onto the internet, the app store or itunes, nor can i update to iOS7!! I sent an email to apple support and they said we don't handle these issues and redirected me back to the help forums which i have already seen and tried everything other people have suggested and nothing has worked (changing date, signing in/out of itunes etc). When i go to app store the screen is blank, in itunes it just keeps saying loading but never gets anywhere and same with the internet! When i go to settings to update to iOS 7.0.4 it says software update unavailable, try again later. Not sure what to do now. Nothing works, can't use my apps, facebook, music etc. Will contact apple again and try get some answers. But thanks for any info
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
10 Ways to Boost Your Wireless Signal
http://www.pcmag.com/article2/0,2817,2372811,00.asp
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
Here's my setup: Internet <> Comcast/xFinity supplied cable modem <> new Apple Time Capsule <> iPhone 4 & MacBook Pro (see below for hardware details)
Internet on my iPhone 4 has been acting slow since yesterday evening. My MacBook Pro was running fine, but just to be sure I checked the Comcast website to see that I have only used 50GB of my allotted 250 GB of data for the month, so it's not that.
I decided it must be a problem with just my iPhone, so I opened up the multitasking bar and quit everything in there manually, and then I held the on/off button, and slid the slider to power off. When I started back up, I could not connect to the same WiFi I had just been using. I tried to reconnect and nothing. I tried to forget the network and try again, nothing. I tried to reset all network settings, nothing.
I have tried all the steps listed here: http://support.apple.com/kb/TS1398 "iOS: Troubleshooting Wi-Fi networks and connections"
Toggled WiFi off and back on
Made sure I am in range of the router (it's about 8 feet away and my iPhone reports full signal from the network)
Made sure all the hardware is connected and on
Checked other devices (I'm successfully connected with my MacBook Pro right now)
Checked for router firmware upgrades (I have a new Time Capsule from Apple with the current 7.5.2 firmware which I've been using for a month)
Restarted my device (again)
Checked that the network is available (it does show on my iPhone)
Restarted my Time Capsule
Checked my router configuration as described here: http://support.apple.com/kb/TS3727 "Wi-Fi: Unable to connect to an 802.11n Wi-Fi network" which involves simply checking to see that WMM is turned on, also stating that WMM cannot be enabled or disabled for Apple's AirPort products.
Reset my network settings (again)
I have searched and searched for fixes to this problem, and I have additionally tried:
Enabling/disabling Airplane Mode
Disabling any network password protection/encryption (no luck), re-enabling it (no luck)
Changing the network password
Checking for hardware addresses present in iOS Settings > General > About (they are present and not zero'ed out)
Switching Bluetooth off (nothing) and back on (nothing)
....and probably a few other things I can't think of right now
I have yet to try:
The "Freezer Trick" which apparently involves chilling the iPhone to get a temporary fix?
Restoring the iPhone (I would really rather not)
A different WiFi network (other than my own Time Capsule home network or guest network, both of which give the same Unable to Connect error)
So, after all of that, are there any more ideas? Is there a reliable solution to this issue? So far I've just seen a lot of "mess with the settings," "the freezer trick worked," and "blame it on the iOS 4 update."
Here are my hardware details:
iPhone 4; iOS 5; 32GB; AT&T; no cellular data plan (July 2011)
TimeCapsule6,113; Firmware 7.5.2; 2TB (September 2011)
MacBook Pro 3,1; Mac OS X (10.7.2); 2.4 GHz Intel Core 2 Duo; Hi-Res Display; 4GB RAM; 500GB HD (August 2007)
...and the Time Capsule config:
http://cl.ly/BCUtUgh. Apparently "messing with it" is still the answer. I decided to try the LinkSys router I was using before I bought the Time Capsule, and my iPhone connected with no problem.
I went through the steps again, and after rebooting my Time Capsule this time, I can connect again. The troubling thing it that this started with a power-off of my iPhone. No changes or installations, just a reset. Am I going to have to reboot my Time Capsule (which has no power switch, just a cord I have to unplug) every time I reboot my iPhone?
Jinkies. -
Ive just switched to a "Motorola SURFboard eXtreme Cable Modem" which is connected to a time capsule.
I am unable to connect to my internet via. wifi on my Playstation.
I have already tried many different attempts to connect to the internet. I have tried to directly connect to the internet using an ethernet cable as well as restarting my mac laptop and playstation. I am only able to connect to the internet on my main computer.
Please help?
I tried being the most descriptive I couldI am only able to connect to the internet on my main computer.
What IP does your main computer get.. ?? Post a screenshot if you can as it helps to see the details.
When you open the airport utility on the main computer.. click on the TC what errors does it show?
They will list in the summary.
What mode is the TC in? If the setup went wrong it might be bridged when it should be in router mode..
Remember any time to change things around with cable modems you MUST shut down the modem as well.. it cannot change the MAC address of the first item easily so need to be off.. a few minutes at least.. sometimes up to 20min or longer. Make sure the TC captures the public IP on the wan interface.. which is the only way this will work with a pure modem.
The most recent TC can still have issues.. new AC version TC and AE have the Max amount of issues with SB6121 and 6141.. there seems to be some ethernet issue between them..
What model TC do you have??
You can slow the LAN port down or specify the actual speed in the Gen1-4. -
UNABLE TO ACCESS THE INTERNET FROM LOCAL PROVIDER ON A SITE-TO-SITE VPN CONNECTION
Dear All,
I have a site-to-site connection from point A to point B. From point B i am unable to access the internet from local internet provider.
I am trying to ping from 192.168.20.1 the dns 8.8.8.8 but i receive the message "destination net unreachable".
When i run "show ip nat translation" i receive nothing.
The vpn connection is working properly, i can ping the other side 192.168.10/24
Below is the configuration of the cisco router on point B.
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.21.254
ip dhcp pool voice
network 192.168.21.0 255.255.255.0
default-router 192.168.21.254
option 150 ip 192.168.5.10
ip cef
ip domain name neocleous.ru
ip inspect name IOS_FIREWALL tcp
ip inspect name IOS_FIREWALL udp
ip inspect name IOS_FIREWALL icmp
ip inspect name IOS_FIREWALL h323
ip inspect name IOS_FIREWALL http
ip inspect name IOS_FIREWALL https
ip inspect name IOS_FIREWALL skinny
ip inspect name IOS_FIREWALL sip
no ipv6 cef
multilink bundle-name authenticated
vty-async
isdn switch-type primary-net5
redundancy
crypto isakmp policy 5
hash md5
authentication pre-share
group 2
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
lifetime 28800
crypto isakmp policy 50
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key Pb85heuvMde9Wdac5Qohha7lziIf142u address [ip address]
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 10
crypto ipsec transform-set TRANSET esp-aes esp-sha-hmac
crypto ipsec transform-set TRANSET2 esp-des esp-md5-hmac
crypto ipsec df-bit clear
crypto map CryptoMAP1 ipsec-isakmp
set peer [ip address]
set transform-set TRANSET
match address CryptoACL
interface FastEthernet0/0
description Primary Provider
ip address [PUBLIC IP MAIN PROVIDER] 255.255.255.252
ip access-group outside_acl in
ip mtu 1390
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
crypto map CryptoCY
crypto ipsec df-bit clear
interface FastEthernet0/1
description TO LAN
no ip address
load-interval 30
speed 100
full-duplex
interface FastEthernet0/1.1
description DATA VLAN
encapsulation dot1Q 20
ip address 192.168.20.254 255.255.255.0
ip access-group inside_acl in
ip nat inside
ip inspect IOS_FIREWALL in
ip virtual-reassembly in
ip tcp adjust-mss 1379
interface FastEthernet0/1.2
description VOICE VLAN
encapsulation dot1Q 21
ip address 192.168.21.254 255.255.255.0
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface FastEthernet0/3/0
no ip address
ip access-group outside_acl in
ip nat outside
ip virtual-reassembly in
shutdown
duplex auto
speed auto
crypto map CryptoCY
ip local pool VPNPool 192.168.23.2 192.168.23.10
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source list nat_list interface FastEthernet0/3/0 overload
ip route 0.0.0.0 0.0.0.0 [default gateway ip]
ip access-list standard VTY
permit 192.168.20.0 0.0.0.255
ip access-list extended CryptoACL
permit ip 192.168.20.0 0.0.0.255 192.168.3.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.5.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.6.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.12.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.2.0 0.0.0.255
permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255
permit ip host 192.168.22.1 192.168.5.0 0.0.0.255
permit ip host 192.168.20.1 192.168.5.0 0.0.0.255
permit ip host 192.168.22.1 192.168.6.0 0.0.0.255
ip access-list extended DFBIT_acl
permit tcp any any
ip access-list extended inside_acl
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.35
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.39
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.23
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.18
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.55
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.144
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.146
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.141
permit ip host 192.168.20.253 host 192.168.3.21
permit ip host 192.168.20.254 host 192.168.3.21
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.10
permit ip 192.168.20.0 0.0.0.255 host 192.168.20.254
ip access-list extended nat_list
deny ip host 192.168.20.254 192.168.10.0 0.0.0.255
deny ip host 192.168.20.254 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.10.0 0.0.0.255
deny ip host 192.168.20.2 192.168.3.0 0.0.0.255
deny ip host 192.168.20.2 192.168.10.0 0.0.0.255
permit ip host 192.168.20.1 any
permit ip host 192.168.20.2 any
permit ip host 192.168.20.254 any
ip access-list extended outside_acl
permit gre any host [ip address]
permit esp any host [ip address]
deny ip any any
ip sla 2
icmp-echo 192.168.10.254 source-interface FastEthernet0/1.1
frequency 180
timeout 500
ip sla schedule 2 life forever start-time now
logging 192.168.3.21
route-map DFBIT_routemap permit 10
match ip address DFBIT_acl
set ip df 0
route-map ISP2 permit 10
match ip address nat_list
match interface FastEthernet0/3/0
route-map nonat permit 10
match ip address nonat_acl
route-map ISP1 permit 10
match ip address nat_list
match interface FastEthernet0/0You cannot access internet, because all traffic is tunneled for VPN !!!!
Please see cisco tech documentation and bypass traffic for internet.
eg. if lan traffic is going from site a to site b then through vpn
else
lan traffic to internet (any) should be out thorugh the vpn . -
I opened up my firefox browser yesterday and it crashed. Since then I get an error message that says "unable to connect" every time I try to load the browser. The setting is set to "no proxy" So it should be connecting. My internet explorer browser is working fine. So I know it is not my internet connection. What can I do to make the firefox browser work again?
Hi,
Maybe the radio connection on the other end is not working. Hope this helps.
xxmitchxx90 -
my itouch cannot connect to internet...but the other day i can use the wifi im connected,but since yesterday eventhough im connected to wifi and the signal is very strong,when im trying to login on FB it says unable to connect to FB,same with YM it says internet connection is offline when in fact i have a strong signal of wifi..
- Reset the iPod. Nothing is lost
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- iOS: Recommended settings for Wi-Fi routers and access points
Do other devices successfully connect to the network?
Does the iPod successfully connect to other networks? -
Have been using Firefox for a number of years. About two weeks when I attempted to access a bookmark through Mozilla I got an unable to connect. Have tried multiple things including removing and reinstalling several times. Each time I attempt to got to a site I receive a "Firefox can't establish a connection to the server at www.X. I'm offered choices to retry; check network connection or check Firewall or proxy and make sure Firefox is permitted access to the Web.
To the best of my knowledge I made no changes to the access. I am able to reach the internet via internet explorer and can reach the sites that Firefox is denied. I've tried playing with the internet connection settings but to no avail.I, too, have used Mozilla/Firefox for yrs and like it very much. After some security issues and my security company worked on the issues, Mozilla/Firefox disappeared from my screen. I'm getting the following when I try to download:
C\user\Lee\App Data\Data\Local\temp
7zEEEE.temp\set up. exe
D:users\Lee AppData\Local
Temp\7zEEEEtemp.\setup.exe
This system could not find the environment option entered.
Might someone be so kind as to help me please?
Thank you,
Leeflea. -
My Firefox automatically updated to Firefox 8. Since doing so, when I open the browser the screen displays a box saying 'Unable to connect' and says the same for any website. My internet connection is fine. I uninstalled and installed Firefox again, but problem persists. Please help as this is really frustrating me :(
Did you try this?
'''Remove Firefox from your program's list of trusted or recognized programs, then add it back.'''
Some Firewalls don't specify which version of Firefox is permitted. <br />New version of Firefox = new executable was installed = new permission is needed
The top 12 ways to get fooled by Firewalls: <br />
http://forums.mozillazine.org/viewtopic.php?p=2295421#p2295421
Maybe you are looking for
-
HP Setup Assistant unexpected closure
I have a HP Photosmart C4795. I have a new wireless network that I am trying to add my printer to. I have updated my operating system (Apple 10.9.4 Maverick) and reloaded the printer software. I tried to run the HP Setup Assistant to configure t
-
GL Account Search Help...
We do not assign GL Accounts. We force the user to select one. We prefer that they use the supplied search help to select the GL. Currently, we are swithing one of our system from an R/3 backend to a non-R/3 backend. For detailed reasons, we ar
-
Itunes Uses 100% of CPU When Ejecting Disc. How can I solve this?
Every time I eject a disc in iTunes I get the beach ball and the program won't respond. I can go to other programs while this is happening but iTunes is froze. I opened Activity Monitor and noticed iTunes was pegging the CPU. Why would this be happen
-
Barbara Brundage, can you help with PS Elements 11 and Epson R2000 printer issue?
Seeking help with PS Elements 11 which does not work with Epson r2000 printer. Epson tech support could not fix, said it is PS e11 problem. Receive prompt on PS e11 screen when I try to print stating "not compatible or settings are not correct. Ha
-
MIGO : add components for consumption (mvt.543) during goods receipt po
Dear guru. Can I add components for consumption with movement 543 during the goods receipt of a purchase order (mvt.101) ? Thanks.