Unable to connect to network ios 7

Tried Reset Network Settings with airpalne mode on and with it off. Reset router. Updated router to latest firmware. Still unable to connect to network.

Hi there casefromab,
it sounds like you have already tried a few things, but you may find the troubleshooting steps in the article below helpful.
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
-Griff W. 

Similar Messages

  • Unable to Connect to Network error with right code

    My Ipod Touch 4G just started having a problem a few days ago i left my house and reset my network settings because i wanted to see something not thinkign about when i got home and now any time i try to connect to it i ge the unable to connect to network error. My friends and family are all using there ipods on our network and they still work and ive tried everything ive updated reset network setting restored the ipod any suggestions on how to fix this?

    - Did you power off and then back on the router?
    - iOS: Troubleshooting Wi-Fi networks and connections
    - iOS: Recommended settings for Wi-Fi routers and access points

  • I am having a major problem connecting to FaceTime. Message reads "unable to connect, check network connections". Yet I am online with Manila, Safari etc. any suggestions.

    I am having a major problem connecting to FaceTime today.  Message reads "unable to connect, check network connections".  I am online, mail works, ex
    Tc.  This was not a a problem two days ago.  Any suggestions?

    Could be that the servers are overloaded today.

  • Imac FaceTime unable to connect to network (safari connected and loading pages).

    I have a brand new Imac, I have never been able to get facetime to work. It keeps getting hung up on the log in page, and eventually gives me an error message of unable to connect to network. Safari and other web based programs are working perfectly. 
    Any Ideas?

    How can I get my Mac to join an open 3Com wireless
    network? The network is recognised but Mac is unable
    to connect...
    The 3Com wireless router is connected to a broadband
    router through a PC running XP.
    Do you have two routers? That may be your issue. You should only be using one router, or configure one of the routers and turn of DHCP.

  • I have been having trouble connecting to my wifi on my ipad mini but my iPod is just fine......it will connect and then say "Unable to connect to network" I've tried resetting my ipad mini and turning off my router for 30 seconds and its not working.

    I have been having trouble connecting to my wifi on my ipad mini but my iPod is just fine......it will connect and then say "Unable to connect to network" I've tried resetting my ipad mini and turning off my router for 30 seconds and its not working.

    What TC do you have? Model number direct from the base is a big help, it will be A1 followed by 3 numbers.. eg
    A1409 Gen 4.. The new AC is A1470
    How is it setup?
    I need the whole network setup. what modem/router, how is the TC connected etc??
    I also need to know what IP the ipod gets, so I can see what mode the TC or network router is working in.

  • Ipod "unable to connect to network"

    i have an ipod4, and i'm only unable to connect to my home router, my friend's ipod connects to it fine, but mine is having problems, i have reset network settings, turned off sercuity on router and was still unable to connect, i have gone into router and opened mac address too but still wont let me connect, any suggestions

    I tried powering down the router. When it's off the iTouch does not recognize the network and then when it's powered on again, the iTouch recognizes the network. Unlike the public wi-fi spots that my iTouch responds to, where all the info like IP Address, Subnet Mask, Router, DNS etc are populated in the settings...my iTouch does not populate these fields at home even though it recognizes the network. I still get the unable to connect to network error. Could it be that my router is antiquated and can not support the iTouch? Like I said earlier, my Router does not recognize the iTouch as being attached to it.

  • NOKIA N8 - Unable to connect - WLAN Network not fo...

    also for NOKIA N8 THE SAME PROBLEM: Unable to connect - WLAN Network not found;I see my network in the wlan list (Tthe state is "knowed") but when i try to connect to it,i read: Unable to connect-wlan network not found;i tryed with: mac filter on/off,dhcp on/of,wep protection on/off,firewall router on/off,power saving in the phone on/off, but the problem is the same ever!..Niklas Savander,..where you are?..nokia is back?..but with the same problems!

    Well, I seem to have issues with WLAN as well.
    When I am approx. 10metres away from my Router, the N8 doesn't connect. However, I can connect to WLAN using my Nokia N900, Nokia E52 and my Netbook (Asus EEE1005HA). This is a N-router with standard settings. I have tried changing, the channels etc. but it doesn't resolve the problem.
    So is this a problem with the Nokia N8? I mean, all my other wireless devices work fine. I even tried changing the Wireless Interface type from N/B/G, to B/G but as I said before, the problem is still there.
    Hopefully this problem can be sorted with a software update, that is if the N8 finds it difficult to connect to Wireless Internet.
    P.S.: Tthere is another thread reporting similar problems. Here is the link.

  • My iPhone 5 says unable to connect to network. I have tried all the trouble shooting...resetting phone, router... No change. Problem occurs everywhere not just at home. Any suggestions?

    My iPhone 5 says unable to connect to network. I have tried all the trouble shooting...resetting phone, router... No change. Problem occurs everywhere not just at home. Any suggestions?

    AmishCake wrote:
    Have you tried restoring your softwareyes
    yes I have

  • Unable to connect to network iphone update server

    I have an Iphone 4 that has been slow for a couple of days , today it started to open app different apps ( click on one and another opened) so i decided to restore and update it . Was running 4.3 . It never updated , has locked in recovery mode . when i try to restore i get a message that the iphone update server network unable to connect . I am running 10.5 itunes on a windows 7 . the iphone is visible in itunes , but when i check the diagnostic it said there is now iOS device connected . Is this a software issue or a hardware issue ? any help would be appreciated .

    VarinderSandhu wrote:
    Helios- Gunes EROL wrote:
    Hi Nasir;
    Please see below note which could be helpful for you:
    ORA-12560: TNS:PROTOCOL ADAPTER ERROR [ID 989716.1]can you pls share me link or url as u suggested above ...
    Regard
    HeliosRegards,
    Varinder SandhuIt's referring to a note in My Oracle Support (formerly known as MetaLink). You need to have a paid service contract with Oracle to access.

  • HT204409 unable to connect to network

    I am unable to join the network.  I have reset all wi-fi and disconnected router and turn ipad 2 on and off and still get the same message.  Any other ideas??  Thank you

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router (Auto is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • "Unable To Connect" iPhones on iOS 6.1.2

    Hi,
    I have a Cisco AP1142N on software version 12.4(21a)JA1. I am able to get my iPhone 5 on iOS 6.1.2 and my iPad on iOS 6.1.1 connected along with a host of other Blackberry and Android devices, however I am unable to get any iPhone 4,4S or 3GS connected even if on the latest iOS version.
    I keep getting the "Unable to Connect" error on the device.
    Is the software version above the latest version? I only have a web interface access to the AP as it is in another part of the building.I currently have TKIP enabled with WPA/WPA2 enabled.
    I would appreciate any help or even be pointed in the right direction, most solutions are command based which are a bit difficult for me to try.
    Many thanks in advance.
    EC

    Right,
    I have now created a new SSID (e.g. GUEST2) for which I have set to use WPA, under express security I can see broadcast enabled for both SSID's, however this second ID cannot be seen by any of my devices. I have ticked the "Multiple BSSID Beacon" as Set SSID as Guest Mode.
    Nothing happens when I try to click the radio button "Multiple BSSID" for the two Radio's.
    Many thanks
    EC

  • Unable to connect to network with Safari and Software Update

    A user I support has encountered a problem with networking. He is unable to connect to the network with Safari and Software Update, but IS able to connect and surf with Foxfire and some other programs. Another unusual symptom is that he actually can connect to one web site (which is in his Bookmarks Bar) with Safari, but can't connect to anything else. He's also unable to navigate off of that one site he connects to. When he runs Network Diagnostics, he gets all green lights (no problems). He has fixed permissions, deleted Safari Cache and .plist, rebooted - not fixed yet. He's using 10.4.8 on a PowerPC G4. Any ideas appreciated (this is the wierdest I've seen in a while!).

    Here's what he did. After reading your post, he created another location in his network preferences, entering EXACTLY the same info that was in his old location (he even used the old DNS addresses), except using a new location name. Then he chose the new location and "everything worked". It's one of life's great mysteries. Thanks for your help - it is appreciated.

  • HT5569 iPhone 5 on ios6.0.1 unable to connect to network

    iPhone was connecting fine till suddenly unable to connect
    I've tried forgetting the network
    Resetting the phone
    Tried turning airplane and trying
    Resetting network setting
    Turning http to auto
    Renew lease
    Non has helped at all, please help thank you

    Does not work for my home wifi, friends wifi nor any hotspot

  • Windows 10 failing unable to connect to network

    Ive just downloaded windows 10 on my hp pavillions laptop  a 15-p264na and it seems like am unable to connect to the network every time i go on edge or firefox I get timed out when I check the drivers it says they are up to date ,  but how can it check if the drivers are suitable for windows 10 if even I cant get on via edge or firefox           It seems via these forums that a lot of users have reverted to windows 8.1  then upgraded again  ,My computer says its connected to my router but when i put it through a system check it says theres no connection as if the drivers not suitable for 10 ,  I am so dissappointed  Ive wasted many hours trying to resolve this issue its like the laptop is useless unable to communicate with the outside world      so it looks like I am going to have to restore windows 8.1 so any advice welcome

    My WiFi and my Ethernet drivers worked on the first boot into Windows 10, then I was prompted to restart again. After that restart I was never able to get on the network again, and in Device Manager it says that both devices were unable to start and had no driver. My only fix was to revert back to Windows 7 then upgrade again. Its been fine since that.

  • Unable to connect wifi on ios 6

    I m unable to connect my wifi after upgrade to iOS6 ...its take me to apple.com.. I try every thing.. Trun off n turn it on.. Reset settings.. Clear cookies ... But it didn't work.. Help....

    have you tried all the help in this apple support document?
    http://www.apple.com/support/iphone/wifi/

Maybe you are looking for

  • XI messages are stuck as Waiting

    Hello, I have several messages in XI which do not send their payload to the destination. They seem to be stuck in XI with the following details: In SXMB_MONI, the Message History states the current status as "Scheduled for Outbound Processing". In SX

  • Alternative content for a user without Flash

    I want to incorporate a Flash navigation bar into my new site, but I realise that some users will not have Flash installed on their pc. Is there a way of having an alternative HTML menu appear if the users pc doesn't have the flash plugin. Cheers S

  • OneNote 2013 - Locking Section keyboard shortcut not working

    I have OneNote 2013 full PC version.  I have a notebook stored somewhere in live.net that has a password protected section. After I unlock the section when I want to lock it using the Keyboard Shortcut (CTRL+ALT+L) it does not work.  I have tried eve

  • Advantages of Non Leading ledger

    Hi Friends, This is Ajay ,can anay one tell me, how to assign a Feild status varient to a non leading ledger in sap fico . Also tell me the advantages of a non leading ledger, and how it works in real time scenario? Thanks & Regards Ajay

  • Why does connmand add and delete route to 87.106.208.187?

    Hi Each time connmand starts the following is logged: connmand[323]: eth0 {add} route 87.106.208.187 gw 192.168.0.1 scope 0 <UNIVERSE> connmand[323]: eth0 {del} route 87.106.208.187 gw 192.168.0.1 scope 0 <UNIVERSE> I can see that I'm not the only on