Unable to connect to Wi-Fi connection using WPA2 PSK authentication and encryption type TKIP

I was referred to here from this thread at the Windows Insider Program: http://answers.microsoft.com/en-us/insider/forum/insider_wintp-insider_web/unable-to-connect-to-wi-fi-connection-using-wpa2/07bae1ed-c7fb-4f85-9d26-5549cc23e57a?msgId=2eb70420-fe35-494b-a13d-dcacd4d55eb9&rtAction=1426697691002
My issue is copy/pasted below:
Original Title: TKIP selection in WiFi network settings
I have a workplace WiFi connection using WPA2 PSK authentication and encryption type TKIP.
On the machine I used to test Windows 10, I had a previous installation of Windows 7 professional which connected to my workplace WiFi using the above settings. After installing Windows 10, my workplace wifi settings were imported and worked fine.
Windows 10 had a system crash, and since I had deleted my previous windows installation, I performed a complete reinstall of Windows 7. However, when I went to install Windows 10 again, I had not taken the time to set up my workplace Wifi on Windows
7 before installing Windows 10. As a result, I had to set up my workplace wifi as a new connection in Windows 10.
When going to set up the wifi connection, the encryption type was grayed out, but appeared to default to AES. Searching the internet suggested that Windows 8.1 did not need a encryption type selected, because Windows could automatically determine
if it was TKIP or AES, hence why the option to select encryption type was grayed out. However, after completing the setup of my workplace wifi, Windows 10 could not connect to my workplace wifi. After restoring Windows 7 with a factory reset, and setting up
the workplace wifi (the encryption type selection was not grayed out and I manually selected TKIP encryption), my workplace wifi was working again.

Similar Messages

Hello I recently downloaded an app on my iphone 4s - Remote mouse- so i can control my laptop that is connected to my tv, it used to work fine and now the connection fails, I downloaded another app and the same problem occurs, its not the firewall

Hello I recently downloaded an app on my iphone 4s - Remote mouse- so i can control my laptop that is connected to my tv, it used to work fine and now the connection fails, I downloaded another app and the same problem occurs, its not the firewall and both phone and laptop are conected to the same wifi, i also tried to connect it manually with the ip address and still no connection, can you help??

Close all open apps by double-tapping the home button, then swiping up and off the screen with the app window (not the smaller icon).
Then reset: hold down the home button along with the sleep/wake button until you see the apple, then let go.(No data loss) Try it again.

Which hp printers use wpa2-psk

My new Netgear R6300 only wants to use wpa2-psk (aes). My old HP printer can not do this security code. Need to get a new HP printer, which one has this level of encription?

Hello, and Welcome to the HP Support Community!
wpa-psk (either AES or TKIP) is pretty standard these days. Looking at my year-old OfficeJet 8600 Pro, it easily supports this method and is the way I have it connected to my home network.
We just installed a newer 8610 at the office, and it had no problems with the wpa/wpa2 encryption scheme either!
I believe you will be safe with any present-day HP printer that offers wireless connectivity.
WyreNut
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

How do I know WinRM uses Kerberos for authentication, and does not fall-back to NTLM?

Hi,
How do I know WinRM uses Kerberos for authentication, and does not fall-back to NTLM?
/SaiTech

Hi SaiTech,
Kerberos will be selected by default in an AD domain, The default (assuming the client is in a domain, and is not connecting to itself via 127.0.0.1 or ::1 addresses) is to use Kerberos authentication, and not to fall back to NTLM.
Please also Note that you may have to take some other steps as well to get non-Kerberos authentication working. Specifically, you'd have to set up an HTTPS listener on the remote host, or modify the client's TrustedHosts list.
Refer to:
WINRM kerberos & Negotiate
Authentication for Remote Connections
In addition, you can also use Network Monitor to check the authentication method.
If there is anything else regarding this issue, please feel free to post back.
If you have any feedback on our support, please click here.
Best Regards,
Anna Wang
TechNet Community Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Wga54g connecting to sony blu ray using WPA-PSK (TKIP) or WPA2-PSK (AES)

My Wga54g is to be the interenet source to my sony blu ray player. I have a wireless broadband router modem setup that uses WPA-PSK (TKIP) and WPA2-PSK (AES). How do I configure everything to work? Since the WGA54G only does WEP is there a way to configure it or the Sony Blu ray to get a internet signal to it? The sony seems to have a automatic IP or manual IP configuration setting option. I suppose I can step down to WEP on the router settings but I'd rather not. I tried that and couldn't get it to work regardless. Please help!

To connect the Wireless-G Game adapter to a wireless network, please determine your SSID, Wireless Security and/or Network Key. Second you need to lower down the security mode to WEP, since WGA54G do not have any other security mode. Here is the link for connecting the Wireless Network using a WGA54G: http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=4558&userrole=Linksy...

Can't connect to home wireless network using WPA2

Using PowerPC 10.4 Tiger.
Wireless is detected by airport card with pw prompt as WEP, but the network actually uses WPA2. Enter PW in prompt, but, of course, it was rejected.
My iPhone can get into my WiFI with WPA2 just fine.
What gives?
When network is configured for WEP, I can log in just fine, but can't take advantage of 802.11n (pre)

To use WPA2 requires an Airport Extreme card.
Run Apple System Profiler and under "Network" select "Airport Card" and it will tell you what type of Airport Card you have. If you don't have an Airport Extreme, you can't use WPA2.
Also, even if you have Airport Extreme cards in your computers, you may need to install extra software to enable use with 802.11n as described in this link
http://store.apple.com/us/product/D4141ZM/A

Connecting an ibook to accesspoint with WPA2-PSK

My Ibook, bought this year, but early (panther 10.x), have problems with connecting to my Dlink accesspoint after setting the security to WPA2-PSK.
Are there any problems with this connection from apples side? The machine is rather new, but I cant get connected ...

WPA with TKIP most certainly does NOT currently provide "good enough security for the time being".
Ref: http://www.cr0.net:8040/code/network/aircrack/
AirCrack is perfectly capably of cracking WPA-PSK using TKIP. It's all about the weakness of RC4 as a cipher. AES is what we truly need. The problem is that we'll have to get Linksys and Apple to stop finger pointing long enough to figure out what the actual problem is and fix it.

Unable to start several servers using the custom. authentication and authorization Provider

I downloaded the Sample Security Providers (http://developer.bea.com/managed_content/direct/SampleSecurityProvidersUnmanaged.zip)
and followed the user guide for installation.
We have following configuration:
- One domain with 3 servers :
- ADM: admin, console
- WTL_1 : WebTool server 1
- WTL_2 : WebTool server 2
WTL_1 and WT_2 are member of cluster WTL_Cluster
I try to restart all servers. It worked fine for the first one (ADM), but for
the other two I got followinf exception:
####<Nov 13, 2002 10:29:02 AM CET> <Emergency> <WebLogicServer> <isoit652.bbn.hp.com>
<WTL_1> <main> <kernel i
dentity> <> <000342> <Unable to initialize the server: Fatal initialization exception
Throwable: java.lang.SecurityException: Authentication denied: Boot identity not
valid
java.lang.SecurityException: Authentication denied: Boot identity not valid
at weblogic.security.service.SecurityServiceManager.doBootAuthorization(SecurityServiceManager.java:1024)
at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:1166)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:697)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
Do you have any idea why it worked only for one server?
Thanks for any help
My Chi

Hi John,
Actually, thanks to your examples, I have my Authentication Scheme setup using a custom authentication function that first checks that the Username/Password are valid, and if so, then validates that the user has also been setup in AD with one of the groups used by my application. What I'm wondering is, when I replace the built-in Authentication Function it appears that the function that I code must have the correct signature (accepts UserName and Password, and returns a boolean)... but I really want to be able to also return the actual AD Group that the user is assigned to for use within my Authorization Schemes. I'm not sure if/how I can do this from my authentication function, or if I just need to re-query AD again in my Authorization Schemes to get the AD group that the user is assigned to.
Appreciate the help,
Lori

SAP Crystal Report using SQL Server Authentication and Windows Authenticati

I'm a SAP Crystal Report, version for Visual Studio 2010 Beginner
my ingredients are
1.windows 7 ultimate service pack1
2.sql server 2008 standard edition
3.visual studio 2010 pro
4.SAP Crystal Report, version for visual studio.net
I was created a report named customersByCity.rpt using OLE DB (ADO) -> Microsoft OLE DB Provider for SQL Server -> I'm supply Server, User ID, Password and Database. I assume me using SQL Server Authentication for my report
Then, my ASP.NET files as following
//ASP.NET
<%@ Page Language="C#" AutoEventWireup="true" CodeFile="viewCustomersByCity.aspx.cs" Inherits="viewCustomersByCity" %>
<%@ Register Assembly="CrystalDecisions.Web, Version=13.0.2000.0, Culture=neutral, PublicKeyToken=692fbea5521e1304"
    Namespace="CrystalDecisions.Web" TagPrefix="CR" %>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head runat="server">
    <title></title>
</head>
<body>
    <form id="form1" runat="server">
    <div><asp:Label ID="lblMsg" runat="server" BackColor="Yellow" ForeColor="Black"></asp:Label>
<CR:CrystalReportViewer ID="CrystalReportViewer1" runat="server" AutoDataBind="true"></CR:CrystalReportViewer>
    </div>
    </form>
</body>
</html>
//code-behind
using System;
using System.Collections.Generic;
using System.Linq;
using System.Web;
using System.Web.UI;
using System.Web.UI.WebControls;
using System.Collections;
using CrystalDecisions.CrystalReports.Engine;
using CrystalDecisions.Shared;
public partial class viewCustomersByCity : System.Web.UI.Page
    private const string PARAMETER_FIELD_NAME = "city";
    private ReportDocument customersByCityReport;
    private void ConfigureCrystalReports()
        ConnectionInfo connectionInfo = new ConnectionInfo();
        connectionInfo.ServerName = @"WKM1925-PCWKM1925";
        connectionInfo.DatabaseName = "Northwind";
        connectionInfo.UserID = "sa";
        connectionInfo.Password = "sysadmin25";
        SetDBLogonForReport(connectionInfo);
    private void SetDBLogonForReport(ConnectionInfo connectionInfo)
        TableLogOnInfos tableLogOnInfos = CrystalReportViewer1.LogOnInfo;
        foreach (TableLogOnInfo tableLogOnInfo in tableLogOnInfos)
            tableLogOnInfo.ConnectionInfo = connectionInfo;
    private void SetCurrentValuesForParameterField(ReportDocument reportDocument, ArrayList arrayList)
        ParameterValues currentParameterValues = new ParameterValues();
        foreach (object submittedValue in arrayList)
            ParameterDiscreteValue parameterDiscreteValue = new ParameterDiscreteValue();
            parameterDiscreteValue.Value = submittedValue.ToString();
            currentParameterValues.Add(parameterDiscreteValue);
        ParameterFieldDefinitions parameterFieldDefinitions = reportDocument.DataDefinition.ParameterFields;
        ParameterFieldDefinition parameterFieldDefinition = parameterFieldDefinitions[PARAMETER_FIELD_NAME];
        parameterFieldDefinition.ApplyCurrentValues(currentParameterValues);
    protected void Page_Load(object sender, EventArgs e)
        customersByCityReport = new ReportDocument();
        string reportPath = Server.MapPath("customersByCity.rpt");
        customersByCityReport.Load(reportPath);
        ConfigureCrystalReports();
        ArrayList arrayList = new ArrayList();
        arrayList.Add("paris");
        arrayList.Add("Madrid");
        arrayList.Add("Marseille");
        arrayList.Add("Buenos Aires");
        arrayList.Add("Sao Paulo");
        ParameterFields parameterFields = CrystalReportViewer1.ParameterFieldInfo;
        SetCurrentValuesForParameterField(customersByCityReport, arrayList);
        CrystalReportViewer1.ReportSource = customersByCityReport;
1st scenario
When in a runtime, it's keep appear a dialog box. This dialog box ask me to suppy Server, User ID, Password and Database. Once all information is supplied, my report display the data as expected
2nd scenario
I change my report using OLE DB (ADO) -> Microsoft OLE DB Provider for SQL Server -> checked on Integrated Security. I just choose Server, and Database. I assume me using Windows Authentication
When in a runtime, there's no dialog box as above. My report display the data as expected. really cool
Look's like, when report using SQL Server Authentication there's some problem. but, when report using Windows Authentication, it's fine.
I'm looking for comment. Please help me

Hello,
MS SQL Server 2008 requires you to install the MS Client Tools for 2008.
Once install then update all of your reports to use the SQL Native 10 as the OLE DB driver.
The try again, if it still fails search, lots of sample log on code in this forum.
Don

Connecting laptops to wireless APs using RADIUS 802.1x and certificates set-up questions

I am working at a small school with 25 laptops for a mobile cart. We upgraded to new dual radio APs and I want to set up the laptops to connect to the APs and validate user credentials at logon. The person before me made a generic username "Student"
on each laptop locally so they could start the laptop and then connect to the wireless with a password. This is less than ideal for many reasons.
I have configured NPS on the server and on the AP. When I login locally and then select the AP I am prompted for credentials and can log in. On NPS's eventlog I can see it granting full access. At that point I do not have internet access which is going to
be a vendor call. I can ping 8.8.8.8 successfully but not the local.domain.org address, nor the server ip 192.168.25.5 which is also the DNS Server. I am thinking that there is a NAT issue there.
When I try to login to the laptops with my AD credentials it is not connected to the AP yet and tells me there is no logon server available.
Is that where the certificates should be used at computer/machine level?
I want to get this setup correctly so anyone who has done this and has some advice for best practice would be greatly appreciated!

Hi,
According your description, we can ping 8.8.8.8 successfully. It means that we have connected to the network.
Due to we can't resolve the domain name, it should be a DNS issue. As you have mentioned, the DNS server is unavailable. Please check if there is something wrong with the DNS server.
If we want client to connect to AP before implement AD authentication, we need to enable single sign on. For detailed information, please refer to the link below,
http://technet.microsoft.com/en-us/magazine/2007.11.cableguy.aspx
Best Regards.
Steven Lee
TechNet Community Support

Connection from jdbc or sqlj using operating system authentication

Is it possible to use the operating system authentication to connect to oracle which is on the same box from jdbc or sqlj??
Any help is appreciated

You can logon using external credentials with the oci driver by passing in null's as username and password.

CALLING ALL EXPERTS - Connected TWO Actiontec Routers to use one as main and second as GUEST

Hello Experts-
I have TWO Actiontec Routers from Fios. I bought the new N one, and I have an old Actiotec that I was previously not using. So here is what I am trying to do...
I'd like to leave Router 1 (the New N router) as my primary router (comes from ONT via cat5 wire NOT Coax) and Set-up the second router off the first to be a guest router. So essentially make it a bridge.
I can't seem to configure it to work correctly.
Can anyone out there give me a step-by-step walkthru on how to configure this second router so I can have them both hooked up, seperate SSID, with one as the Main and the other being the Guest?
THANK YOU IN ADVANCE!
Rob
Solved!
Go to Solution.

I'm basically wondering how to change the routers IP address and where the Disable DHCP is within the menus.
THANKS IN ADVANCE!
Rob
To change the IP address of the Local Area network choose:
My Network
Network Connections
Click edit on the row for "Network (Home/)office"
On the next screen click Settings
On the next screen you can change the LAN (192.168.1.1) address to something different.
On the same screen you can disable DHCP too.
I hope this helps.

Unable to do Software update, access iTunes, use widgets on dash and upload

*_Here is the problem:_*
1. Unable to use Software Update. When I try I get: "+A networking error has occurred: timed out (-1001). Make sure you can connect to the Internet, then try again+" This is despite being connected to the internet and getting most things done.
2. Widgets which require data retrieval are not working. Notably weather and currency convertor.
3. iTunes cannot connect to the store. Tells me to check my network (which, if I do, I am told is fine, thanks)
4. Cannot view images (such as car rental vouchers) which are meant to display in email. In fact- the entire email disappeared before my eyes! But CAN, luckily, view on the server so I KNOW it is not just that the image is "spam" etc.
5. First thing on this list which made me wary- I cannot upload to YouTube, it times out ("unknown error" but timing out is mentioned) and this is using Firefox 3.8.3.
6. Safari will not load at all- it just keeps trying to load.
7. Displaying pages is slower than usual and downloading Onyx took ages and displayed no data regarding the file size or length of download time.
*_What I know:_*
1. I didn't update the last two times I was prompted because I was too busy to have it shut down on me and restart, etc.
2. I also had a go at trying to set up a web proxy and failed miserably. Though I actually changed the settings on another network to the one I am using I am so not network-literate that I fear that I have somehow done this to myself.
*_What I have tried:_*
1. safe starts, restarts,
2. deleting the preferences pertaining to Software Update from the various locations,
3. repaired permissions and-
4. thought of (I cannot afford to lose the data and haven't the time to back up just now- as per usual, this comes at the WORST time as I am on standby to fly out of the country due to VERY heavy and sad family affairs and need access to the files on the computer even if I cannot fully use the internet- just too many people/GB Pounds riding on this) using Onyx to try to "fix" this.
I have read up on others getting similar issues but am not certain that everyone has ALL the symptoms I am seeing (and then they may not be busy trying all these things on the one day and may not KNOW it is affected as well!). And I have tried each and every cure offered to these people. No good.

When you are going to be connecting to different networks that require different settings--such as proxies--you must establish different Locations in your Network System Preferences. If you're going to be connecting at college, you may want to set up a location called "College" and set the proxy settings so you can use it there. Then, when you want to go online at school, go to System Preferences -> Network and change your location to College. Then when you get home, change your settings back to "Automatic" or whatever you've named your home location.
Your Mac doesn't differentiate between networks it's connected to in order to automatically apply different settings. It relies on you to do that through the Locations set-up.
Anyway, glad it's working for you, and thanks for the star!

Which hp printers uses wpa2-psk(aes)

Need to update my HP printer. New router wants to use the newer wpa-psk(aes), want to buy HP that has same. Do not see this info on any of the descriptions of the newer printers. Help.
This question was solved.
View Solution.

Hello, and Welcome to the HP Support Community!
wpa-psk (either AES or TKIP) is pretty standard these days. Looking at my year-old OfficeJet 8600 Pro, it easily supports this method and is the way I have it connected to my home network.
We just installed a newer 8610 at the office, and it had no problems with the wpa/wpa2 encryption scheme either!
I believe you will be safe with any present-day HP printer that offers wireless connectivity.
WyreNut
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

I would like to put all my iPhone videos to my macbook air than put it on a dvd to watch on any dvd player how would i do that using my usb superdrive and what type of dvd would i need

I have just transferred all my iphone videos into my macbook, now I would like to put these videos onto a dvd for playing on any dvd; how would I do that with my usb Superdrive dvd/cd drive. I don't see a option to burn. Please help and responses is greatly appreciated, I am a New macbook user.

You need an app like Toast by Roxio (http://www.roxio.com/enu/products/toast/default.html). You would use Toast to burn the videos to a DVD-R disc.

Unable to connect to Wi-Fi connection using WPA2 PSK authentication and encryption type TKIP

Similar Messages

Maybe you are looking for