Unable to connect to wism2 module via session command

Hi There,
I installed two wism2 modules in our cat6509.
After basic configuration the modules comes up and I can connect via ssh/https to the controller.
For first configuration of the wism modules, I opened a session directly from the cat6509.
Now after 24 hours, there is no way to make a connection via session command from cat6509.
cat6509#session slot 9 processor 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
Trying 192.168.12.100 ...
% Connection refused by remote host
cat6509#session slot 2 processor 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
Trying 192.168.12.101 ...
% Connection timed out; remote host not responding
Has anybody an idea why I can not open a session to wism2 module?
Thanks
Bjoern

You can load the software via the command line interface.              Configuration via WebUI is not available at this point since the  Management             Interface on the wireless controller is not configured  yet. The controller             should be configured to operate properly on your  network and configured with             the IP addresses of your working  subnets. You can configure the wireless             controller by directly  attaching it to the console ports on the WiSM2             controller or opening  a console session to the controller module from the             Catalyst  interface as shown here.
Note: You can access the WiSM2 through a session command directly                 now.
CAT6504-MA#session slot 3 processor 1
The default excape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
Trying 192.168.2.21 ... Open
(WiSM-slot3-1)
User: admin
Password:*******
(WiSM-slot3-1) >

Similar Messages

  • Unable to connect to Deskjet 3545 via Wireless Direct from Windows 8.1 laptop (Lenovo Thinkpad E530)

    Hi, It's a newly bought printer. I am unable to connect to the printer via Wireless Direct from Windows 8.1 64bit laptop. I have enabled the Wireless Direct with security on the Printer. Connected to the Printer SSID from my laptop wifi. Created the new printer from Driver software. It discovers the printer with it's name,IP etc; Upon selecting the printer and click on 'Next' button on the screen, results in a 5 min search process and finally displays that it could not connect. I have tried pinging the printer and it's able to pingf the IP of the printer successfully. I have even tried disabling the Norton antivirus, but result is the same. regards,sathwik  

     

  • Curve 9380 unable to connect to the internet via wifi

    I'm using curve 9380 and unable to connect to the internet via my home wifi, there is no blackberry logo beside the wifi signal symbol. I don't have this probelm if I'm using my laptop or curve 8520 to connect to the internet via the same wifi router. Please help. Thank you.

    Check firewall, if you're on wifi then try ethernet to rule out interference. It is likely a network issue.

  • Can not access FWSM via session command in cisco 6513 (VSS enabled)

    Dear All,
                  Today i received FWSM from cisco (RMA), I need to configure it as standby unit for existing FWSM active/standby setup.
    IOS on RMAed FWSM is 2.3.4 and  cisco VSS supports FWSM IOS 4.0.4 and later.
    My issue is, I cannot access FWSM (IOS 2.3.4) via session command from cisco 6513 but could successfully consoled it without any problem. I have reloaded it twice and also tried to disable and enable power on it.
    VSS#sh module switch 2
    Switch Number:     2   Role:  Virtual Switch Standby
    Mod Ports Card Type                              Model              Serial No.
       2    6  Firewall Module                        WS-SVC-FWM-1  -----------
    Mod MAC addresses                       Hw    Fw           Sw           Status
      2  0034.2fd7.3b04 to 0019.2fa7.3b0b   4.2   7.2(1)       2.3(4)       Ok
    Mod  Online Diag Status
      2  Pass
    VSS#session switch 2 slot 2 pro 1
    The default escape character is Ctrl-^, then x.
    You can also type 'exit' at the remote prompt to end the session
    Trying 127.0.1.21 ...
    % Connection timed out; remote host not responding
    Can someone please let me know why I cannot access FWSM through session command ?
    Whether this is because of older IOS ? If yes then how to upgrade its IOS ?
    Is it possible to upgrade IOS via FWSM console ? if yes, please let me know.
    Do i need to test on different slot ?
    Look forward to hearing from someone.
    Thanks & Regards
    Ahmed...

    There is a limitation that FWSM running version older than 4.0.4 will not accept session from the switch if the FWSM is not seated into switch 1 AND if switch 1 is not active.
    So to upgrade the FWSM you either need to use the console or put the FWSM physically in switch 1.
    Thanks,
    Jeroen

  • OD users unable to connect to a server via afp

    We have a Mac OS 10.9.2 with Server 3.1.2.  We are able to access the server for file sharing via smb with OD accounts just fine.  But we are unable to connect to the server using afp with any OD account, only local system accounts.  I have tried turning off SMB for all of the file shares, but this did not help resolve the issue.
    The log shows a login attempt immediately followed by a logout.
    Aug  7 13:40:33 server.company.com AppleFileServer[736] <Info>: IP 192.168.101.2 - - "Login -----" -5023 0 0
    Aug  7 13:40:33 server.company.com AppleFileServer[736] <Info>: IP 192.168.101.2 - - "Logout -----" -5023 0 0
    I did edit out the user and the server name.
    Any help would be greatly appreciated.
    Thank you.

    Many Open Directory problems can be resolved by taking the following steps. Test after each one, and back up all data before making any changes.
    1. The OD master must have a static IP address on the local network, not a dynamic address.
    2. You must have a working DNS service, and the server's hostname must match its fully-qualified domain name. To confirm, select the server by name in the sidebar of the Server application window, then select the Overview tab. Click the Edit button on the Host Name line. On the Accessing your Server sheet, Domain Name should be selected. Change the Host Name, if necessary. The server must have at least a three-level name (e.g. "server.yourdomain.com"), and the name must not be in the ".local" top-level domain, which is reserved for Bonjour.
    3. The primary DNS server used by the server must be 127.0.0.1 (that is, itself) unless you're using another server for internal DNS. The only DNS server set on the clients should be the internal one, which they should get from DHCP if applicable.
    4. Follow these instructions to rebuild the Kerberos configuration on the master.
    5. If you use authenticated binding, check the validity of the master's certificate. The common name must match the hostname and domain name. Deselecting and then reselecting the certificate in Server.app has been reported to have an effect in some cases.
    6. Unbind and then rebind the clients in the Users & Groups preference pane. Use the fully-qualified domain name of the master.
    7. Reboot the master and the clients.
    8. Don't log in to the server with a network user's account.
    9. As a last resort, export all OD users. In the Open Directory pane of Server, delete the OD server. Then recreate it and import the users. Ensure that the UID's are in the 1001+ range.

  • HT4623 Unable to connect 4S to itunes via cable

    Unable to connect to Itunes via docking station

    An Apple docking station? What is happening or not happening when you try and connect?

  • N70 unable to connect phone to compter via USB hel...

    Brand spanking new N70, downloaded PC suite however not able to connect phone to compter via USB to transfer music. Can anybody help?

    Hi bento
    When you install PC Suite for first time there are TWO seperate processes, firstly installing PC Suite then returns to desktop and then secondly establishing connectivity during which "Nokia Connectivity Cable Driver" and "PC Connectivity Solution" installed.
    You could go to Setings > Control Panel > Add/Remove Programs > Repair and see if this helps
    Happy to have helped forum in a small way with a Support Ratio = 37.0

  • Unable to Connect to Mounted Volumes via AFP; Local Network

    Server's name is Boing. If I try: Connect to Server: afp://Boing.local I'm given a list of possible volumes. However, this list only includes my home directory and every user's Public Folder. I am an admin user:
    uid=516(mnewman) gid=516(mnewman) groups=516(mnewman),101(com.apple.sharepoint.group.1),105(com.apple.sharepoint. group.3),103(com.apple.accessscreensharing),98(_lpadmin),102(com.apple.access_ssh),81(_appserveradm),79(appserverusr),80(admin),20(staff),106(com.apple.sharepoint.group.4),104(com.appl e.sharepoint.group.2)
    I should have access to all mounted volumes:
    drwxrwxr-t 56 root admin - 1972 May 17 13:39 /Volumes/Banana
    drwxrwxr-x 13 mnewman mnewman - 510 Jan 14 09:17 /Volumes/Farang
    lrwxr-xr-x 1 root admin - 1 May 21 10:46 /Volumes/Fuji -> /
    drwxrwxr-x 12 mnewman mnewman - 476 Apr 20 08:29 /Volumes/Guava
    drwxrwxr-t 17 root admin - 646 May 17 13:39 /Volumes/Lime
    If I ssh into Boing, I can get to everything.
    If a different admin user connects to Boing via afp she can get to everything.
    What has happened to my account that permits me afp access only to public shares?

    Amazing:
    I used Apple's Workgroup Manager to add a short name (mgnewman) to my account.
    Using that short name I can now connect to Boing using the Finder's Go->Connect To Server...
    and, all the mounted volumes are shown.
    Workgroup Manager shows "mnewman" as my default short name. But, it doesn't work right
    for afp connections either through the GUI or command line. But, my newly added short user
    name works just fine. (Oddly, my Dot Mac e-mail address, also shown as a short user name in
    Workgroup Manager, also works....)
    I suspect that the Directory Services database is somehow corrupt.
    Is there a way to rebuild it?

  • Unable to connect to PC Suit via bluetooth

    I Have a Noia 6233 And IVT Bluesoil Bluetooth dongle installed on Windows XP pro SP 2.
    When I am trying to connect to PC suit via bluetooth i gets a warning "cannot use connection type. Check that all needed hardware, software, and drivers are available" When I have checked system information through - help- about nokia pc suit I found detecetd bluetooth stacks as - Microsoft (Version: 5.1.2600, Build: 2180)only
    I have nokia PC Suit 7.0.9.2 and blue soil version 1.6.1.4 release 050606 and stack version 05.04.05.20050408.
    Plz Help me me to get out of this trouble asap.

    I have the same issue.
    I'm trying to use PC suite (downloaded from nokia site as the proper one for 6230i rel 7) connecting 6230i via bluetooth. Pc and phone are "associated" but when i launch the PC suite I get an error message: "It is not possible to recognize the phone".
    I read a lot of post but nobody seems to have solved the issue!
    From Bluetooth application I can read files on pc ... so che bluetooth connection seems to work properly; it appears as a PC suite bug .. really boring!
    Nokia team can help us ?

  • Unable to connect to Deployment share via the 2012 Update 1 workbench.

    Hi Everyone,
    This is a tricky one, I've been scratching my head for a few days now. I have a MDT deployment share, which lives on a server, for argument sake, lets call it: MDT-01. Via the Servers MDT Workbench, I can connect to the deployment share just fine, from
    any PC, other than my main PC (which is running Windows 8.1), I can connect to the deployment share just fine. If I load the MDT Workbench on my main PC, it just has a deployment share folder with a red cross on it. If I attempt to remove it, it crashes the
    MMC, if I try and open the same deployment share it crashes the MMC. If I give the Deployment Share a different share name, it errors and says I can't use an existing deployment share folder.
    I used to be able to connect to the share just fine, but since the last couple of days I've not been able to connect.
    Further investigation with PowerShell reveals that the console thinks it has a persistent drive, DS001, but the path is blank, as in ''.
    Restore-MDTPersistentDrive -verboseVERBOSE: Restoring drive 'DS001' with path ''WARNING: Unable to restore drive DS001.
    If I try to remove the Persistent drive, it errors, and if I try to add any new drive to either the same deployment share, or an alternative, it fails.
    I can use the New-PSDrive and Remove-PSDrive Powershell commands to create/remove a replicated drive, but that doesn't actually change the Path value in the Get/Restore-MDTPersistantDrive, as they seem to be separate, even though I think they should
    be linked.
    The Internet has been no help, so I'm asking the Microsoft crew to be helpful, and not just do the usual "This is posted in the wrong place, this question will now be closed... etc, etc!" This is an MDT question, not a Powershell question, I just
    need anyone who has indepth MDT knowledge to look at this.
    To make clear, this is not a question about a client connecting to the deployment share, that all works fine, and I can update the deployment share fine from any other workbench.
    I cannot connect to my deployment share, from my local MMC MDT workbench, as it thinks it already has one, but with a blank path. I've uninstalled, and reinstalled both the MDT, and ADK components on my Local PC, but I still cannot connect to the Share.
    My question is this: The files/registry that stores this DS001 path setting is clearly local to my PC, but where is it, I've search the reg, and I've check files, but to no avail, I'm likely to rebuild my PC because of this, but I'd rather not if I can help
    it.
    Any Ideas people?
    P.s. Sorry if this post seems rude, I do appreciate the help, I just don't have time for being messed about, as we're migrating our XP system to 7, and with less than 60 days remaininf, I could do without this... Thanks for understanding. :D

    Persistent drives are just a easy way for the MDT console to keep track of the Deployment Shares you like the most (think of it as "pinning" Deployment Shares to the console).
    The list of persisted Deployment Shares are per user and stored in the file:
    "%AppData%\Microsoft\Microsoft Deployment Toolkit\User.Config"
    Mine looks like:
    <?xml version="1.0" encoding="utf-8"?>
    <configuration>
    <userSettings>
    <MDTProvider>
    <setting name="Drive1Name" serializeAs="String">
    <value>DS001</value>
    </setting>
    <setting name="Drive1Path" serializeAs="String">
    <value>C:\DeploymentShare</value>
    </setting>
    <setting name="Drive1Description" serializeAs="String">
    <value>MDT Deployment Share</value>
    </setting>
    </MDTProvider>
    </userSettings>
    </configuration>
    Make sure the Drive Path points to something valid, otherwise, I would delete (rename) the file and let MDT re-create the file.
    I hope this answers your question.
    Keith Garner - keithga.wordpress.com

  • Unable to connect to the UCCX via VPN

    Hello, i have an issue,
    when i am trying to login to the supervisor desktop agent via VPN, an error occurred
    "unable to create connection with web-server. Chech the server with address *.*.*.*:80"
    thankx in advance

    With the script editor, the login prompt requires username/password/IP address of CRS server. So one would think that name resolution would not be required - yet the application references Call Manager by name and my VPN client could not resolve the name until I created a host file entry.
    But this doesn't appear to be related to your issue. From your VPN client, are you able to ping your server IP address?

  • I am unable to connect to the internet via WiFi connection.  My iphone works just fine.  Please advise possible solutions.

    I have an iPad on v5.01.  I am unable to use my wifi network to connect to the internet.  My wife's iPad works fine.  Please advise any potential solutions.

    Have you checked to see if your WiFi router needs to have your iPad's MAC address specifically permitted to use WiFi?  Some WiFi routers have a section in the settings called "Access List", possibly under "Security".
    You can find the MAC address in Settings > General > About > Wi-Fi Address

  • Unable to connect to Nike+ website via iTunes

    Just got my Nike+ stuff in today, and it won't let me connect to the site when it asks me to login to my Nike+ account via iTunes and connect to the Nike+ site.
    When I go to login, I get an error saying I don't have an internet connection (although I'm on cable).
    When I go to create a new account, it says it can't connect to the host site.
    Any ideas? Anyone else run into this issue? I've made sure I have the latest software for iPod and latest version of iTunes already.

    Are you using your apple login as your Nikeplus login? I was having the same problem as you. Our iTunes/ipods are listed under my husbands email but I registered with nikeplus with my own email address. It kept telling me that my nikeplus username/password were incorrect but I could login to the nikeplus site without a problem. I created a new nikeplus account with my husbands email address and iTunes connected just fine.
    Of course, now I am upset that I am being forced to use the nikeplus site under my husbands email address.

  • Updated firefox, now I am unable to connect to the internet via mozilla but other browsers still work

    When mozilla asked my for an update several months ago I chose to skip the install and wait. Did the install soon after and firefox stopped working even though my connection to the internet is fine. I uninstalled mozilla firefox, used another browser to access the mozilla website to reinstall firefox. This fixed my problem and firefox was working again, until another update came along. This time attempting to uninstall and reinstall did nothing. Once again I am left using another browser to use the support forum and firefox is not working. Please help!!

    That is an indication that a firewall is blocking the new version of Firefox. For details see [[Firefox cannot load websites but other programs can]].

  • Logon issue, unable to connect Netweaver AS JAVA via URL

    As the installation guide indicates to use URL "http://<hostname>:5<Instance no.>00" to logon the system.
    The system is up and running, is there any addtional config?
    How to logon the system?

    Hi Spencer,
    Since it is a java stack only , so there will be no user like DDIC and SAP* at database level.
    SAP* user is a kernel level user (which means hardcoded at kernel level) which is used in emergency situation.
    J2EE_ADMIN user is present in DUAL stack since you having a java stack only then it that case you will have administrator user.
    I know the default password for DDIC , SAP* and EARLYWATCH users but not for administrator.
    You can check with  default password such as 06071992 and 19920607(not sure)
    The JAVA equivalents of the SAP* password, some history and a usefull tip.
    With Regards
    Ashutosh Chaturvedi

Maybe you are looking for