Unable to connect to wrt54g V8

I bought a LG BD390 DVD player with wireless capability for netflix and video streaming. I am having difficulty connecting wirelessly to the router with the DVD player. The player can find the wireless network but it can not make a connection to it. If I disable security on the router I can make a connection and access the internet. Does anyone know what the problem is? Thanks

Thanks for the reply. I have the WPA TKIP security. When I turn security off I am able to get a connection. I can not get a connection with WEP security. I tried messing around with the MAC filter, but kind of did not know what I was doing.
I do not have any problems with laptops or a Wii game system accessing the router with security turned on. I do not understand what makes this DVD so special. My knowledge is limited with routers. I tried downloading an upgrade for the router, but my computer was unable to implement the .bin file. If you have any other suggestions/ help I would appreciate it. Thanks, Ike

Similar Messages

Unable to connect to WRT54G

I am trying to connect to 192.168.1.1 and I keep getting Failure to Connect to Web Server. If I disconnect my satellite modem then I get a time out error. I want to enable WPA security but I can't even get to the cofiguration screen to do that. I've been working on this for 4 hours and I'm really getting frustrated. I can still connect to the internet (obiviously since I posted this), but I can't cofigure my router. I've reset the factory settings (pressing the reset button for 30 seconds.. more than once) and still nothing. I'm at my wits end here. Please someone help me... ugh

As for now you are not able to login to your router setup page, So the first thing which you need to do is, Click on the Start Button - Click on RUN - and in the RUN box type "CMD" and Click Ok... and in the command prompt window type "Ipconfig" and check whats the IP address you are getting it from your Router to the Computer, then again in the Command Prompt window type "Ping (Default Gateway IP address) and Hit Enter and check if you are getting any replies.
Then open IE and in the address bas type that Default Gateway IP address, and it will Prompt you for the Username and Password, Leave the Username Blank and in the Password Typed "admin" and click Ok. Now you will be able to login to the router setup page.
If still you are not able to login to the router setup page, Then you Unplug the Power from your Router and Keep it unpluged for 30 seconds and after 30 seconds plug the power to your router and try to login to your router setup page. In case if you are still not able to Login to the router setup page, Then Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 60 seconds and re-connect the power cable...Now you can try to login to your router setup page, I think you might be able to login to the router setup page.I think this should work for you.

Third PC unable to connect to WRT54G

I already have two PCs hardwired to the router and they work great. I've tried to hook up a third PC but it doesn't seem to be able to contact the router and I can't get a valid IP address with DHCP. Even if I hardcode the IP address it doesn't work. I hooked the same PC up to a different network and it worked so I know the issue isn't the PC.

how long have u had the router? have u tried all the ports and change cables? coz as u said u have tried connecting the pc to other network...basically, 2 desktops are already working now only 1 desktop is not connecting.

Suddenly unable to connect - WRT54G

I have a Linksys WRT54G router connected to a PC. 2nd PC connects fine via wireless adapter. 1 laptop connects fine. Newest laptop connected fine until 4 days ago. Now it shows the wireless network with full signal, but is unable to connect for more than 30 seconds to 3 minutes at a time with long gaps of no connectivity between. I am able to connect to other wireless networks with no lag or drop, outside my home.
I have: reset router, powered down and powered up modem & router, changed SSID from default name, turned off firewalls and antivirus (back on since nothing changed), disabled MAC and Security Mode on router, updated drivers, restored the laptop to a date before the problem occured.
Out of ideas and very hopeful that there is a fix. Any help is greatly appreciated!
Solved!
Go to Solution.

First of all, set "SSID Broadcast" to "enabled". This will help your computer find and lock on to your router's signal.
Poor wireless connections are often caused by radio interference from other 2.4 GHz devices. This includes wireless phones, wireless baby monitors, microwave ovens, wireless mice and keyboards, wireless speakers, and your neighbor's wireless network. In rare cases, Bluetooth devices can interfere. Even some 5+ GHz phones also use the 2.4 Ghz band. Unplug these devices, and see if that corrects your problem.
In your router, try a different channel. There are 11 channels in the 2.4 GHz band. Usually channel 1, 6, or 11 works best. Check out your neighbors, and see what channel they are using. Because the channels overlap one another, try to stay at least +5 or -5 channels from your strongest neighbors. For example, if you have a strong neighbor on channel 9, try any channel 1 through 4.
Also, try to locate the router about 4 to 6 feet above the floor, in an open area. Do not locate it behind your monitor or near other computer equipment or speakers. The antenna should be vertical.
Also, in the computer, go to your wireless software, and go to "Preferred Networks" (sometimes called "Profiles" ). There are probably a few networks listed. (If you have a long list, this might be the sole cause for your problem.) Delete any network named "linksys". Also delete any network that you do not recognize, or that you no longer use. If your current network is not listed, enter its info (SSID, encryption (if any), and key (if any) ). Then select your current network and make it your default network, and set it to automatic login. You may need to go to "settings" to do this, or you may need to right click on your network and select "Properties" or "settings".
Some users have reported improved wireless performance by switching from to WPA encryption.
If you continue to have problems, try the following:
For wireless g routers, try setting the "Transmission Rate" to 54 Mbps.
If you still have trouble, download and install the latest firmware for your router. After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
Hope this helps.

Unable to connect to the router! (wrt54g v. 2)

I just got a router from a garage sale; it was still in the box and everything.
Well, I tried hooking it up to my modem and computer to get wifi, but I can't get it to work.
This is the setup:
modem -> router -> computer
I can access the internet when the setup is this way, but there's no wifi, and I can't access 192.168.1.1 or set it up using the CD it came with. When I go through the setting up process with the CD, I get this error message that says "Unable to connect to router! Check that the router has been connected to the computer, and that you're ethernet adapter is working."
When I try to go to 192.168.1.1, it says "The connection has timed out." I can't ping it either.
I've also tried resetting it several times, but that doesn't do anything.
Someone please help!

Hi sylentknight and welcome to the forums!
You said that you are able to connect to the internet with this set-up: modem -> router -> computer right? So does that mean that you can ping the router when it is connected directly to your computer? Reason why I'm asking is if it does work, you can try to configure the router for the wireless settings while it is directly connected to the router first then try to go wireless. Please let me know if understood your post correctly.

Unable to connect to internet with my WRT54G router

I had no problem until a few days ago. I have it under a secured mode and wanted to unsecure it temporarily. I got into the 192.168.2.1 and clicked the security tab and got a clock that never seemed to come back to i closed the window. I went back into internet explorer and could not get into the internet.  I get a popup in lower right saying Local Area connection. This connection has limited or no connectivty. You might not be able to access the internet or some resources. For more information click this message.
Then I get
Windows could not finis repra the problem because the following actin can not be completed. Renewing your IP address.
I do a setup and get a message
Unable to connect to the router
I try pinging the 192.168.1.1 and it times out.
I do a diagostic and
HTTP Error 12007 connecting to www.microsoft.,com  shows up many times.
I have an Actiontec 701 DSL modem. I can get into the internet using that only.
I've tried resetting the router, I've done   what appears to be a firmware upgrade (lights blink etc), I've tried different power up sequences, I've tried re-booting.
What more can I try?

As of now you are not able to login to your router setup page, and you are getting an error message "Limited or no Connectivity". First you can try is Unplug the Power from your router, wait for 1 min and reconnect the power to your router and check if you connected to the router or still you are getting the same error message.
If still the same problem persist then Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

WRT54GS V2 Unable to Connect

For some time I've been unable to connect to the website http://www.zagg.com. I thought it was my ISP but after contacting them I learned it was my router. I don't really know a great deal about router advanced settings and I don't know what to do. Please Help! Thanks in adv.
Message Edited by Drklazarus26 on 11-20-2009 12:43 PM

What is the ip address you are getting on the hard-wired computer..?
Are you able to see the network name on the Wireless Computer..?
Are you getting any error message on the Wireless Computer..?
Try to reflash the firmware of the router...You can download the firmware from www.linksys.com/downloads.On the linksys setup page,click on Administration tab and click on firmware upgrade to upgrade the firmware.After upgrading the firmware,reset the router again for 30 seconds,power cycle the entire network...
Open the setup page again...Under the setup tab,click on Mac Address Clone tab and click on enable>>>click on "Clone My PC's Mac" and click save settings..Now,click on the status tab and check if you are getting the valid ip address...?
If you are getting the valid ip address then,try to go online on the wired computer...If you are able to go online on the wired computer then,reconfigure the wireless settings and try to go online from the Wireless computer.

WRT54G: Unable to connect to the Router!

I have set up my router exactly as told in the setup wizard, but when I get to step 8, I encounter a problem and I get the following error message:
Unable to connect to the Router!
Check that your Router has been connected to the computer, and that your Ethernet adapter is working!
Oddly, my wired internet works just fine through the router, but my wireless doesn't because I can't complete the setup. All the lights that are supposed to be on are on and not blinking or anything.
What do I need to do to fix this?

you can actualy configure the router without using a setup cd.. you can try accessing the router setup page using your working computer that is wired to the router. just go to internet exp. type 192.168.1.1 on the address box.. it will ask for password- just type admin. go to the wireless menu - change the ssid to any name that you want to name your network. try to view wireless networks on your wireless pc and check if you can see the name that you set. connect to it..
you can check if it works.
Piz Brother,
>>>--DARK_TEMPLAR -->

WRT54G unable to connect to certain internet addresses

The title is a little misleading but I wasn't sure how to word it properly.
Here is my problem, my router frequently does not want to connect to many addresses even though I can ping them. If I try to download from my newsgroup server it just says unable to connect, if I try to watch youtube videos I get an error occured. The only way to get around this is to power cycle my router. Any ideas on what's going on? I have to do this at least every other day.
edit:
I forgot to mention that I have updated to the latest firmware to try to remedy this issue.
Message Edited by jtadeo on 08-12-2009 03:05 PM

After upgrading the firmware, did you reset the router...if no then follow the steps...
Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link

Can't connect to WRT54G after firmware update

I just tried to update the firmware on my WRT54G (version 8.0) and have not been able to connect to the router since then. The firmware said that it had been updated successfully, however I have been unable to connect since it reset itself, and the Ethernet and Internet LEDs are all constantly on even though nothing is connected (the power light on the other hand is behaving normally, not blinking or anything). I have tried resetting the router by holding down the reset button for 30 seconds, but this does not change anything, the router still cannot even be pinged. If anyone can give me any help at all with this, it will be very much appriciated. Thanks.

It sounds like the router might already be dead. But there is always hope that you might be able to revive it.
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

Unable to connect to wifi Linksys

Purchased IPAD 2 four days ago and I have been on the phone with customer service and read several forums and I am still unable to connect to WiFi even though I have two Laptops and a wireless printer which all work fine. I have done all resets, changed my security to WPA from WEP after speaking to customer support at Apple but still unable to connect. I have a Linksys router WRT54GS and would replace it if I knew this would help but I am not seeing anything to say this will work. Any suggestions?

Try going to Settings/Safari/Reading List and turn off Use Cellular Data.

Unable to connect to " http.192.168.1.1 " . Saf...

Unable to connect to " http.192.168.1.1 " . Safari message : " cannot connect with service. " I just got a new Linksys wireless router and have it connect. Linksys 802.11g Model WRT54G. I am connect to internet with " Ethenet." . The router working just great. But can bring the web.page so I can set my setting.
Thank You
Joyce/

To view the router's web pages:
Use Internet Explorer, it usually works.Point Internet Explorer to "192.168.1.1" (with no quotes)
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall. If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.

Message "WLAN: Unable to connect. Wlan Network not...

Well guys i bought my nokia 5800 today so like any other curious people i looked the wi-fi hoping connect with the internet and when i try to connect with the wi-fi appears this message "WLAN: Unable to connect. Wlan Network not Found." and then it dosen´t connectbut he finds normally the networ and this message appears after i type the Router password.i´ve already looked in another foruns and i´ve already switch off the Option Qos in my router and the problem cotinues, so anyone can help me?my router is one linksys wrt54g and the type of connection is static ip an the security is Wpa Personal TKIP....
PLEASE ANYONE CAN HELP ME?I´D BE VERY GRATEFUL WITH THE SOLUTION FOR MY PROBLEM...
Thanks
Message Edited by darkcraft on 13-Jul-2009 09:47 PM

tomasvaril wrote:
Same To me. I have Asus WL-500W router at home, WPA2-PSK(AES), password similar to this "lIGf@91pY0TnFY!Jh@7LjTUlsL3ZPY", MAC address filtering. My old Nokia E51 works, my Touch Pro Works with it. When i try my one day old Nokia E72 it does not work, the same like others:WLAN: Unable to connect. Wlan Network not Found. E72 works at my work wifi, which has the same settings but without mac filtering. Have no idea what is happening, all is setting correctly. MAC address of E72 is allowed on router. It has the same settings like E51, but E51 works like a charm E72 does not work. What is wrong?
As already suggested, you could try disabling the MAC filtering from the router, just to outrule possibility of a typo while entering E72's MAC address to router settings.
Have you tried swithing a WLAN channel that your router uses?
Log in to your router's web management pages (check router's default IP address and username/password from it's manual) and switch of the "Automatic" channel selection mode. Try few different channels, like 1, 3, 6, 9, 11, if one of the channels happens to work any better. Note that in case you have set your router to use channels 12 or 13 (or in case "Automatic" channel selection mode has decided to select channel 12 or 13) you must have a SIM card inserted and some other than "Offline" profile enabled on your phone since Offline mode (i.e. airplane / flight mode) won't allow your phone to operate on higher channels than 11.
In case you have configured your WLAN network (SSID) to be "hidden", try disabling hidden SSID mode on the router.
Asus WL-500W router seems to be a pre-standard 802.11n device so might be worth looking in to your router's WLAN settings and see if playing around with router's WLAN operating mode and settings improve the situation. First of all ensure that your router is not set to operate in 20/40MHz mode (set it to 20MHz only) assuming that the router is in default 802.11b/g/n mode. You could also try disabling the 802.11n mode completely by selecting a 802.11b/g mode (if available).
You should probably also check that you're running latest (2.0.0.6 ??) firmware version on your Asus WL-500W router since there seems to plenty of complaints regarding WLAN connectivity and stability issues (in general, not specific to Nokia handsets) with this particular router model.

TS1398 I am unable to connect wifi on my phone 4s since last 2 weeks... I am living in shanghai and did not have this issue since 2 weeks... iPad works fine... Please suggest some measures... Tried the on off reset settings etc.

I am unable to connect wifi on my phone 4s since last 2 weeks... I am living in shanghai and did not have this issue since 2 weeks... iPad works fine... Please suggest some measures... Tried the on off reset settings etc. but no luck ...
In fact after updating the software to the latest version I am having more of this... Sometimes the wifi button freezes an I can't even slide it to on / off...
Thanks

Noooo! Actually I too had d same prob wit my iPhone 4S. When I connect to my wifi network it won't get connected or it wil be grey scaled! I took it to d istore and since I had warranty they replaced my IPhone. It iPad charger has high volt than ur iPhone charger so when u connect wit it, there is a chance where large amount of current passes thru ur iPhone. So for sure it wil damage ur motherboard and its parts! Many said that iOS 6 or 6.0.1 or 6.1 was d reason for tis wifi prob! But apple never made its mistake wit it's software. If and only if u hav hardware prob u wil hav these sort of wifi prob Bluetooth prob! So best way s to replace ur iPhone!

Published pdf form is unable to connect with database

Hi Guys!
I have created a PDF form using Adobe Live Cycle Designer which have some text fields namely RECORD and NAME. I have connected this form with a Database. When I enter a record in the RECORD number field the NAME field of this form has been populated with the help of XFA Script which is written on the exit event of the RECORD text field. When we publish this form, a new interactive PDF is created which works fine and populates the NAME field from the an SQL database but when I access this PDF form (which is located on a shared location) from some another location (not on the same machine where i designed this form) it is unable to connect to the database and does not work as expected.
I think there is some thing i am missing for the database connectivity.
If any body on this forum can help me out.
thanks
Here is the Script for the above form which i used to populate the NAME FIELD on the basis of enetered RECORD number.
----- Document.Page1.txt_MRN::exit: - (JavaScript, client) -----------------------------------------
/* This dropdown list object will populate two columns with data from a data connection.
sDataConnectionName - name of the data connection to get the data from. Note the data connection will appear in the Data View.
sColHiddenValue - this is the hidden value column of the dropdown. Specify the table column name used for populating.
sColDisplayText - this is the display text column of the dropdown. Specify the table column name used for populating.
These variables must be assigned for this script to run correctly. Replace <value> with the correct value.
var sDataConnectionName = "DataSource"; // example - var sDataConnectionName = "MyDataConnection";
var sColHiddenValue = "RecordNum";   // example - var sColHiddenValue = "MyIndexValue";
var sColDisplayText = "Name";   // example - var sColDisplayText = "MyDescription"
// Search for sourceSet node which matchs the DataConnection name
var nIndex = 0;
while(xfa.sourceSet.nodes.item(nIndex).name != sDataConnectionName)
nIndex++;
//var oDB = xfa.sourceSet.nodes.item(nIndex);
var oDB = xfa.sourceSet.nodes.item(nIndex).clone(1);
oDB.open();
oDB.first();
// Search node with the class name "command"
var nDBIndex = 0;
while(oDB.nodes.item(nDBIndex).className != "command")
nDBIndex++;
// Backup the original settings before assigning BOF and EOF to stay
var sBOFBackup = oDB.nodes.item(nDBIndex).query.recordSet.getAttribute("bofAction");
var sEOFBackup = oDB.nodes.item(nDBIndex).query.recordSet.getAttribute("eofAction");
oDB.nodes.item(nDBIndex).query.recordSet.setAttribute("stayBOF", "bofAction");
oDB.nodes.item(nDBIndex).query.recordSet.setAttribute("stayEOF", "eofAction");
// Clear the list
this.clearItems();
// Search for the record node with the matching Data Connection name
nIndex = 0;
while(xfa.record.nodes.item(nIndex).name != sDataConnectionName)
nIndex++;
var oRecord = xfa.record.nodes.item(nIndex);
// Find the value node
var oValueNode   = null;
var oTextNode   = null;
var sRecordNum = $.rawValue;
for(var nColIndex = 0; nColIndex < oRecord.nodes.length; nColIndex++)
if(oRecord.nodes.item(nColIndex).name == sColHiddenValue)
oValueNode = oRecord.nodes.item(nColIndex);
else if(oRecord.nodes.item(nColIndex).name == sColDisplayText)
oTextNode = oRecord.nodes.item(nColIndex);
var found= 0;
while(!oDB.isEOF())
if (oValueNode.value== sRecordNum)
txt_FirstName.rawValue = oTextNode.value;
txt_LastName.rawValue = oTextNode.value;
found = 1;
break;
//this.addItem(oTextNode.value, oValueNode.value);
   oDB.next();
   if (found == 0)
    txt_FirstName.rawValue = "";
    txt_LastName.rawValue = "";
// Restore the original settings
oDB.nodes.item(nDBIndex).query.recordSet.setAttribute(sBOFBackup, "bofAction");
oDB.nodes.item(nDBIndex).query.recordSet.setAttribute(sEOFBackup, "eofAction");
// Close connection
oDB.close();

Finally achived the database connectivity for the published pdf form developed in the Adobe LiveCycle Designer 8.0.
There must be the same driver version of the DSN on both machines. The machine which published the form and the one accessing it.
Use the Admin account to add the DSN on both machines.
Get rid of the error: Connection for Source "DataConnectionName" failed because the environment is not trusted.
Thanks
AbdulHafeez

Unable to connect to wrt54g V8

Similar Messages

Maybe you are looking for