Unable to Connect to Xbox Live on Xbox One due to ...

I have been on the phone for a few hours this afternoon trying to get this sorted and the conclusion of my last call to BT was that I needed to register on a tech experts website? Put simply, I need to open a list of seven ports that are listed here:
http://support.xbox.com/en-GB/xbox-one/networking/network-ports-used-xbox-live
in ordder to be able to connect to Xbox Live with my Xbox One, this is an issue I have had since upgrading to infinity.
Can somebody do it for me, I have the IP address of my Xbox One, or can somebosy point me in the right direction?
It seems to be taking a very long time to get sorted.
Thanks in advance.

Think I can help here.
First of all I assume that you have disabled UPNP on the hub?  If you havent yet then you have two choices:
You can disconnect the Xbox One and 360 from the network, perform a full factory reset of the hub and then immediately disable UPNP before doing anything else, or..
Disable UPNP and wait a good few hours (I'm talking overnight here) before reconnecting the XBox One and 360 and trying again.
When UPNP is enabled and the XBoxes are using the network it will write rules on the fly to the NAT table, you probably won't be able to apply port forwarding rules to a device for those ports because the Hub can see that they're already in the NAT table.  They will eventually expire but this can take some time.  When you disable UPNP, these rules don't seem to be removed as you might expect.
Next, you definitely don't need to forward ports 80 or 53, these are allowed by the hub automatically and traffic for each will be correctly forwarded to whatever device by the hub.  You shouldn't need to open 88 either.
You have an XB One and a 360 and they both can't share the same port, that being 3074.  However, if the 360 is using 3074 you can forward 3076 to the XB One instead, or vice versa.
When you've applied all of your port forwarding rules run the XBox network test repeatedly until it gives you an open NAT, a maximum of six times should do it, and you may want to do this every time you turn on an XBox.  I've previously posted about why I think you have to do this sometimes with the BT Home Hubs.
If you're still not getting an Open Nat, turn off the XBox and unplug any powerline adapters on its chain for 5 minutes, then reconnect the adapters in sequence from the hub and try again.

Similar Messages

  • Having problems connecting my xbox one to my aiport Extreme.

    Asked for public (static) IP's from my ISP and then got directed to Apple then Mircosoft. Having a lot of problems just trying to connect for my xbox live. More details: i live in an apartment complex that provides my internet through a jack in the wall, every other game console i own works perfectly (Nintendo Wii U and 3DS) any help would be appreciated becuase i feel close to pulling all my hair out trying to figure this out

    I am assuming that you can connect your Xbox One to the Internet but just not to Xbox Live! successfully ... correct?
    If that is the case, the issue is that you may need to reconfigure the router in order to open ports that are required for Live!. Since you live in an apartment complex that provides Internet service, that may not be possible if the complex owns the router.

  • Connecting a xbox one to a iMac

    I am attempting to connect a xbox one to my mid 2010 imac as I have read on the forum and on the net that it is possible although people are saying you need a kanex xd which to me I am not willing to spend the money on it as it is quite pricey so I was wondering if a Moshi Mini DisplayPort to HDMI cable would work instead as it is much cheaper than the kanex xd.
    Thanks for the help

    It uses Target Display mode. The 5K iMac does not support it
    The only 2010 iMac that support that mode is the 27" one
    Target Display Mode: Frequently Asked Questions (FAQ) - Apple Support
    From reading this
    You need the Kanex converter or similar since yo have to convert the X-box singal into a signal that acts like a video from another computer. The simple mini displayport to HDMI adopter works in the other direction.

  • Unable to connect to Windows Live

    Strange problem on my fully upgraded Arch system. Seems I'm able to connect to every website except Windows Live.
    I can load live.com and see the login form. Attempting to submit the form (in Chrome) results in a timeout, followed by the error message:
    "Error 101 (net::ERR_CONNECTION_RESET): Unknown error."
    I can log into to the live.com website from other computers in my house, so there's nothing wrong with my ISP.
    Attempting to connect to msn in pidgin results in a long wait, followed by: "Connection error from Notification server: reading error".
    Here are the relevant sections from my pidgin -d output:
    (00:34:46) util: Writing file /home/dugan/.purple/prefs.xml
    (00:35:23) soap: read: Connection reset by peer
    (00:35:23) soap: Received secure request.
    (00:35:28) msn: servconn 000 read error, len: 0, errno: 11, error: Resource temporarily unavailable
    (00:35:28) msn: Connection error from Notification server (64.4.61.86): Reading error
    (00:35:28) connection: Connection error on 0x19aca00 (reason: 0 description: Connection error from Notification server:
    Reading error)
    (00:35:28) account: Disconnecting account [REDACTED] (0x1535640)
    (00:35:28) connection: Disconnecting connection 0x19aca00
    (00:35:28) msn: destroy the OIM 0x19b01a0
    (00:35:28) msn: destroy httpconn (0x19b0e90)
    (00:35:28) connection: Destroying connection 0x19aca00
    (00:35:34) util: Writing file accounts.xml to directory /home/dugan/.purple
    My Pidgin msn connection settings are all at defaults: server: messenger.hotmail.com; port: 1863; use HTTP method: no; http method server: gateway.messenger.hotmail.com; Proxy type: Use Global Proxy Settings.
    On my Slackware box, in the same room of my house, Pidgin has the exact same settings and has no trouble connecting to msn.
    This problem has persisted at least since yesterday (when I noticed it).
    What's going on?
    BTW, I should mention that I had successfully used pidgin on Arch Linux just a week ago, with a 2.6.33.7 kernel and a TL-WN321G wifi dongle. Here is photographic proof. Now I have a 2.6.35-ARCH kernel and a TP-Link TL-WN722N, and live.com is not working.
    Last edited by dugan (2010-10-02 08:00:17)

    I have the same issue.
    can not connect to MSN since last upgrade on yesterday.
    have no clue...
    -----------------------edit------------------------------------------
    I was using telepathy-butterfly as the backend to connect to MSN,
    and it failed.
    but if I changed to telepathy-haze (which use the same backend as Pidgin), it works.
    Last edited by bsdson.tw (2010-10-22 03:51:26)

  • Unable to connect through windows live messenger o...

    When i try to sign in to Windows Live Messenger, I get the meesage "cannot sign you in to messenger. This maybe because your phone is in flight mode or you do not have a data connection. Please check your access point and network settings and try again"
    how can i successfully run messenger.

    Following are the versions:-
    Oracle:-
    *10g Release 2 (10.2) for Microsoft Windows (32-Bit)*
    Windows:-
    Windows Vista Home Premium version 6(Build 6002: Service Pack 2)
    But may i know, is Windows Home edition is a real issue ? If yes, then how am i able to connect with SQL*Plus and not with iSQL*Plus ?

  • Unable to connect or discover 8610 all-in-one / MAC & Win 7 64 bit

    My 8610 all-in-one previous has been working fine as a wireless network printer for both my MAC OS 10 and laptop Win 7 64 bit.     Suddenly the 8610 will not print from either device.   I downloaded and installed the latest drivers for both from HP.   I restarted all devices several times and finally reconnected the 8610 to the wireless network using the WPS button on the cable modem. The 8610 is showing a connection to the wireless network on it's display and the computers are both able to access the internet. Still no joy.   Not sure what to do next.     Suggestions ? ? ? 

    You can try the dds plugin from here:
    http://fnordware.blogspot.com/2014/09/dds-plug-in-for-after-effects-and.html
    There is also link on that page to a Nvidia plugin

  • Unable to connect my 1300 series all in one printer

    the connect and update buttons from the pull down menu are disabled and i don't know why or how to enable it again. I have one print job in queue that will not restart!!!! please help. thanks in advance!

    Greetings pbdq,
    As the user above stated, you should remove the previous software used.
    When you go to re-add the printer, it may download the software you need via Apple Software Update.
    However, if it does not, use the link above.

  • Unable to connect to my officejet6600 all in one to my Toshiba laptop

    recently had to set up a new landline phone system and in the process  lost my connection to my
    officejet 6600    I tried the HP scan Doctor and no luck     I had to change some setting on the
    fax side to respond to the new phones and answering machine but have lost the wireless connection
    for my printer           any ideas?

    So do you have a new wireless network (with a new name and password)?
    If so, on the front of the printer: Setup > Network > Restore Network Defaults.
    Next, in the same Network menu, run the Wireless Setup Wizard.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Unable to connect to Canon printer MG4270 by one particular MacBook Pro

    Dear friend,
    MacBook Pro bought in  mid 2010, Intel Core 2 Duo, OS X 10.9.4 (13E28)
    The OS X was re-installed after the disk was erased.
    The Canon printer MG4270 was connected to the Airport Time Capsule using WiFi.
    Through Apple Store, Canon Inkjet printer software update V3.0 has been installed.
    Canon IJ Network Tool V4.4.0 has been installed.
    When I add the printer, the printer cannot be connected. See the captured image.
    I have  2 other MacBook Pros of newer models; they can connect and print to the printer. One of them is just purchased 2 weeks ago. I have successfully installed the printer.
    Thanks,
    Danny

    Hi there chow098,
    You may find the troubleshooting steps in the article below helpful.
    Troubleshooting printer issues in OS X
    http://support.apple.com/kb/TS3147
    -Griff W. 

  • Can I play my xbox one through my Toshiba laptop?

    can I play my xbox one through my Toshiba Laptop I have windows 8. I tried connecting my xbox one to my laptop through a HDMI cable and no picture came up on my laptop screen for my xbox one. wondering how to make this work.
    would appreciate help on how to do this thanks.

    Hi
    As far as I know something like this is not possible. HDMI port is for signal output only. You cannot send audio and video signal into your notebook using HDMI port and use internal display for external devices.

  • New Product - My Passport X for XBox One & PC Gamers (3/31/15)

    WD is proud to introduce the My Passport® X portable hard drive for gamers.
    When connected to Xbox One™ or a PC, the sleek 2 TB My Passport X drive provides much-needed storage capacity for gamers to store up to 50 extra game titles, eliminating the need to delete previously purchased games from their Xbox One or PC hard drives and removing those “storage full” warning messages while allowing players to get back to their games.

    Use gOOgle ... and do some research and read reviews  http://www.amazon.com/Passport-Portable-Hard-Drive-WDBCRM00200BBK-NESN/dp/B00V7RJCD6 p.s. looks like it's 5400 rpm   

  • Xbox one moderate NAT on Homehub 5

    Hi, got a shiney new Homehub 5 yesterday, but when I connected my Xbox One it says the NAT is moderate.
     Ive looked online, but theres nothing that relates to my issue. I tried some advice that related to the Homehub 3, set the 'always use this IP address' to yes and it didnt help.
    Anybody got any pointers, as Im bad enough at COD without being limited lol.
    Homehub 5
    Xbox one with a wired connection
    Cheers, Craig
    Solved!
    Go to Solution.

    I've just had a home hub 5 today and currently have an open NAT in both the xbox one dashboard and call of duty Ghosts.
    To do this I only had to do a few things.
    First of all open internet explorer in the xbox one and make sure you have already gone through smart settup and turned off parental controls.
    Afterwards put the xbox in energy saving mode and switch it off.
    Next open a web browser on your PC.
    First go into the hub settings by typing bthomehub.home in the address bar. If that doesn't work then try typing 192.168.1.254.
    Click advanced settings. Type in password if asked then click go to advanced settings.
    Click 'Home Network'
    Then find the xbox one in the network diagram. By default it should be listed as Xbox-SystemOS
    Where it says always use this IP address click 'Yes' then click Apply.
    Next Click the Firewall tab then click port forwarding.
    Click 'Manage games and applications'
    Click 'Add new game or application'
    Where it says game or application name just type COD XB1
    Where it says Copy an existing game or application click 'No'
    Where it says protocol leave as 'Any'
    In the port range setting type 3075 - 3075
    leave translate to blank then click add
    Click apply then OK.
    Go back to main port forwarding screen then where it says Game or application click the arrow in the drop down box and select COD XB1. In the device box select XBox- SystemOS.
    Then click add then click Apply.
    Switch xbox back on and try testing multiplayer connection again after testing press and hold both triggers and bumper buttons at the same time. this should open the nat on dashboard.
    Also try cod and you should now have an open NAT.

  • OneNote cannot connect to Windows Live

    Hi,
    I'm having a problem with OneNote 2010. I want to create a notebook and share it using the "Web" option. However, when I try to connect OneNote to Windows Live, it keeps "connecting to server" for a long time and then reprompts, saying
    "Unable to connect to Windows Live". I don't even get the sign-in dialog box.
    I've tried the following solutions:
    1. Reset IE settings
    2. Checked Firewall exceptions
    3. Ensured Windows is updated
    Some people have bene able to solve the problem by switching off Two-Step Verification, but I haven't turned it on in the first place.
    It's vital that I am able to share this notebook with my project researchers, so solutions would be greatly appreciated!
    Thanks,
    Arish

    Hi there,
    I have the exactly the same Problem. First it started on my Desktop Computer, then two days later i realized the same issue on my Notebook Computer. Logging in on OneNote online, Android- or iOS-Devices works fine.The only special thing on the
    day I first realized was that I set up a different computer using Windows 8.1 and the same Windows Live-ID.
    Any help is greatly appreciated.
    Thanks
    Andreas

  • Xbox one on HP 2009m monitor will it work

    Will it work and what adapter do I buy?
    I am trying to connect my Xbox one to HP 2009m monitor
    The monitor does not use a hdmi cord
    Can I buy an adapter for it and will it work?

    http://m.ebay.com/itm/141210464113?_mwBanner=1
    Will this work?

  • Unable to connect to the repository for this domain

    Hi,
    on the Application Server Control interface of my ContentDB Middle-Tier instance, I have the following error on top of the "Content" Domain :
    Error: Unable to connect to the repository for this domain
    Due to this error, I'm not able to start the default Node (OC4J_Content is started) and I don't see any Domain properties, Node Configurations, Service Configurations within the Administration of the domain. This means that I cannot change any of these properties, but ContentDB is up and running...
    When I try to start the Node, I have the following error in the opmn log:
    2007/04/12 18:47:32 [oracle.ifs.management.domain.NodeManager] [10] INFO: Initialize: starting service IfsDefaultService
    2007/04/12 18:47:32 [oracle.ifs.management.domain.NodeManager] [10] SEVERE: Node Manager, unable to start service, throwing
    oracle.ifs.common.IfsException: IFS-45083: Unable to start service (IfsDefaultService)
    oracle.ifs.common.IfsException: IFS-20102: Unable to start service (IfsDefaultService)
    oracle.ifs.common.IfsException: IFS-20010: Unable to get service configuration properties (SmallServiceConfiguration)
    java.sql.SQLException: ORA-00604: error occurred at recursive SQL level 1
    ORA-02248: invalid option for ALTER SESSION
         at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:137)
         at oracle.jdbc.driver.GetCharSetError.processError(T2CConnection.java:3260)
         at oracle.jdbc.driver.T2CConnection.getCharSetIds(T2CConnection.java:2966)
         at oracle.jdbc.driver.T2CConnection.logon(T2CConnection.java:318)
         at oracle.jdbc.driver.PhysicalConnection.<init>(PhysicalConnection.java:433)
         at oracle.jdbc.driver.T2CConnection.<init>(T2CConnection.java:141)
         at oracle.jdbc.driver.T2CDriverExtension.getConnection(T2CDriverExtension.java:78)
         at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:571)
         at java.sql.DriverManager.getConnection(DriverManager.java:512)
         at java.sql.DriverManager.getConnection(DriverManager.java:171)
         at oracle.ifs.beans.LibraryService.getServiceConfigurationProperties(LibraryService.java:812)
         at oracle.ifs.beans.LibraryService.startServiceUsingDatabaseUrl(LibraryService.java:607)
         at oracle.ifs.beans.LibraryService.startService(LibraryService.java:520)
         at oracle.ifs.management.domain.NodeManager.startService(NodeManager.java:2486)
         at oracle.ifs.management.domain.NodeManager.bootstrapServices(NodeManager.java:3201)
         at oracle.ifs.management.domain.NodeManager.run(NodeManager.java:1012)
         at oracle.ifs.management.domain.NodeManager.main(NodeManager.java:594)
    Does anyone have an idea on how to solve this ?
    Regards,
    Nicola
    PS:
    I have OracleDB, ASInfrastructure and ContentDB (only one instance) installed on the same Windows 2003 server with the following versions:
    - Oracle Database 10.2.0.1 + Oracle Database Companion CD (for Ultra Search) + Patch 10.2.0.2
    - Oracle Metadata Repository Creation Assistant 10.1.2.0.2
    - Oracle Application Server Infrastructure 10.1.2.0.2
    - Oracle Content Database 10.2.0.0

    I called Apple support at 5 pm, it is now 10:30 pm. I am STILL getting the SAME error, saying it is unable to connect to the iphone restore (for upgrading to iOS 4), they said to wait and try every thirty minutes, but it's getting old...

Maybe you are looking for