Unable to connect when 3G is enabled....

I've just noticed a problem with my 3G iPhone, since yesterday the phone refuses to connect to a 3G network, it just says 'no service'. The only way I can use the phone is by disabling the 3G, then it connects to 2G/Edge fine. Wireless works fine whether 3G is enabled or not.
I've removed the sim card and also completely hard restored the phone but nothing works. I've also used the sim card in a Sony Ericsson 3G phone and it works perfectly on the 3G network.
Has anyone noticed this problem at all?
Many thanks,
Dave

Yeah but the thing is I tried the sim card in another phone (a SE K800i) and 3G worked fine.
I'm on o2, England by the way.
I've just spent 4 weeks in California and had the 3G turned off for the whole time (to save battery life as I knew I would not be using data), 3G worked fine before travelling to the US.
This is very strange, I think the 3G radio chip has died, it's going back to Apple later today so I'll report back.

Similar Messages

Help! Getting "Connection error Check connection" when trying to enable HP Web Services on M1536DNF

Can anyone tell me what I need to do in order to enable HP Web Services on HP LaserJet Pro M1536DNF model? Everything works fine and shows it's connected to the network but I cannot enable HP Web Services. It says "Connection error Check connection" I've tried restarting everything; network, printer, computer. I've also updated firmware to latest version as well.

Hi snapry,
Welcome to the HP Support forums. I understand that you are getting an unable to connect message when trying to enable the web services for your Laserjet CP1025nw printer.
Please set a manual IP address and manual DNS servers for the printer. The instructions can be found in the document Printer Does Not Maintain Wireless Connection. There is a Windows section and a Mac section. In the Windows section you will find the instructions in the sub-section titled “Solution three: Assign the printer a static IP address”. For Mac the applicable sub-section is titled “Solution two: Assign the printer a static IP address”. When entering the information for the Manual Preferred DNS server please use 8.8.8.8 and for the Alternate Preferred DNS server please use 8.8.4.4. These are Google’s DNS servers.
After setting the manual IP address and manual DNS servers, you should have no problems enabling the web services.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Unable to connect when downloading apps

I get unable to connect MSG. When downloading apps

Can't connect to the iTunes store?
The Complete Guide to Using the iTunes Store
http://www.ilounge.com/index.php/articles/comments/the-complete-guide-to-using-t he-itunes-store/
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/TS3297
Best Fixes for ‘Cannot Connect to iTunes Store’ Errors
http://ipadinsight.com/ipad-tips-tricks/best-fixes-for-cannot-connect-to-itunes- store-errors/
Try this first - Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
This works for some users. Not sure why.
Go to Settings>General>Date and Time> Set Automatically>Off. Set the date ahead by about a year.Then see if you can connect to the store.
 Cheers, Tom

Wifi unable to connect when tv streams media

We just got a new Sony TV tonight that has a non wifi, LAN connection, and the Netflix application on it. As soon as I logged into Netflix on the TV, my iPad is unable to connect to wifi. I've tried disconnecting, reconnecting, renewing, and restarting router. The minute that I turned off the TV, I'm able to connect just fine again. Any help would be greatly appreciated
Cheers,
Brian

if the tv suck up all the bandwidth for the netflix connection it would mean no more internet for other devices

Unable to connect, when connected

Two days ago, a Verizon repair man replaced my router for the internet. Since then, I have been unable to connect to anything that allows downloading, such as Itunes and EA game downloader. I get a message that states that he connect has timed out, or is not connected. I have tried everything to figure it out. I am running Windows Vista with the Service pack 1. I have an actiontec router M series. Please help me! TIA!

What kind of problems were you having that made the repairman replace the router?
Are you connected through ethernet wire or wireless?

I have been using my ipad by wifi but I am unable to connect when i plug in my cable to my PC - what settings do i need to change if any ?

I use my ipad by wi fi at home but at a friends house I have to connect to a pc by cable - I am unable to get internet what settings do i need to change?

You can't get Internet using the cable.

Printer wont connect when wep password enabled

Hi. I've had a HP Deskjet 5850 for many years. It worked perfectly with my D-Link wifi router, it connected wirelessly with no issues. I recently bought an airport extreme, I've reset everything on the printer and it works via ethernet, but it only works via wifi when airport is set for wireless security is set to none. If I assign a password of any sort it won't connect.
In the printer's admin webpage I've set and reset it for a wep password and it wont connect. Does anyone know if this printer is compatible with airports wep password protection?
Thanks!

I created a WEP password, this is what the printer supports. However, even my MacBook had issues logging in with WEP, it would get bumped off the network and then could only log into the my airport extreme's wireless network after a restart... and then it would get bumped off again. So I switched the airport to WPA/WPA2 password and the macbook works fine now, and the connection is faster than it was with a WEP password. Does the AirPort have known issues with WEP?
Thanks!

Why do I get the "unable to connect " page when I am connected to the internet?

My operating system is XP. I can go to most of my pages without the "Unable to connect" tab. When I go to Microsoft page it displays but I will get the "Unable to connect" when I try to download Windows Media player.
== URL of affected sites ==
http://www.microsoft.com/windows/windowsmedia/player/11/default.aspx

Let's start simple. Try clearing your cache and cookies.
# Open the Tools menu, then select Clear Recent History... .
# In the '''Time Range to clear:''' drop-down, select '''Everything'''.
# Click the arrow next to '''Details''' to display the list of items that can be cleared.
# Select both '''Cookies''' and '''Cache'''.
# Click Clear Now .

'unable to connect' and 'localhost' and index.php and dreamweaverCC

Hi.
I am developing a Web Site and index.php is my point of entry.
Document Root Library/WebServer/Documents
so my path is: Library/WebServer/Documents/dwwdSite
httpd.conf file is modified to add index.php and have it listed first.
<IfModule dir_module>
DirectoryIndex index.php index.html
<IfModule>
Troubleshooting:
I was using Netbeans IDE and when I ran index.php it opened in the browser.
When I launched 'any' of my index.php files from Netbeans IDE, they opened correctly in the brower
I am now using DreamweaverCC and when I run the index.php Error Message ' Unable to Connect'.
For the last 2 days I have been working on this and I am completely stuck.
This morning I thought of another way to test the 'unable to connect' error.
I decided to copy this same file into Netbeans IDE and I NOW get the same Error Message ' Unable to Connect'
when running index.php from Netbeans.
Somehow, my settings are not correctly configured anymore.
Here are my screenshots from Dreamweaver > manage sites.
I believe that this is a rather simple fix that I am somehow not seeing.
Maybe some can spot some mistake.
I appreciate your help and explanation.

Site window settings.
Site Name: dwwdSite
Local site folder: /Library/WebServer/Documents/dwwdSite
Server window settings.
Server Name: testing Server
Address: Macintosh HD/Library/WebServer/Documents/dwwdSite
Connect using: Local/network
Testing: yes (checked)
Server folder: /Library/WebServer/Documents/dwwdSite
(I also tried this: Server folder: /Library/WebServer/Documents)
Web URL: http://www.localhost/dwwdSite
Server Advanced tab: (within server window settings)
Testing server: PHP MySQL
Advanced Settings window.
Local info: Web URL: http://www.localhost/dwwdSite
Enable cache: yes (checked)

'unable to connect' and index.php

Hi.
I am developing a Web Site and index.php is my point of entry.
Document Root     Library/WebServer/Documents
so my path is:       Library/WebServer/Documents/dwwdSite
httpd.conf file is modified to add index.php and have it listed first.
<IfModule dir_module>
DirectoryIndex   index.php   index.html
<IfModule>
Troubleshooting:
I was using Netbeans IDE and when I ran index.php it opened in the browser.
When I launched 'any' of my index.php files from Netbeans IDE, they opened correctly in the brower
I am NOW using DreamweaverCC and when I run the index.php Error Message ' Unable to Connect'.
For the last 2 days I have been working on this and I am completely stuck.
This morning I thought of another way to test the 'unable to connect' error.
I decided to copy this same file into Netbeans IDE and I NOW get the same Error Message ' Unable to Connect'
when running index.php from Netbeans.
Somehow, my settings are not correctly configured anymore.
Here are my screenshots from Dreamweaver > manage sites.
I believe that this is a rather simple fix that I am somehow not seeing.
Maybe some can spot some mistake.
I appreciate your help and explanation.

Hi Sudarshan.
You have been very kind and very clear in your explanation.
One of the very best that I have ever communicated with on this forum !
I have checked many, many things.
I wanted to make certain that I killed apache and restarted it.
I do not think it is RUNNING at all.
1.
myNameMacBookPro:~ myName$ pwd
/Users/myName
2.
myNameMacBookPro:~ myName$ ps -ax | grep http
1892 ttys000    0:00.00 grep http
3.
myNameMacBookPro: myName$ hostname
local
4.
myNameMacBookPro:etc myName$ cd apache2
reginaMacBookPro:apache2 myName$ ls
extra            httpd.conf.pre-update    mime.types        other
httpd.conf        magic            original        users
5.
myNameMacBookPro:apache2 myName$ sudo nano httpd.conf
myNameMacBookPro:apache2 myName$ sudo apachectl -k restart
Syntax error on line 1 of /private/etc/apache2/users/myNameBU.conf:
Invalid command '{\\rtf1\\ansi\\ansicpg1252\\cocoartf1187\\cocoasubrtf370', perhaps misspelled or defined by a module not included in the server configuration
httpd not running, trying to start
myNameMacBookPro:apache2 myName$
6.
The above code may be a hint at part of the problem.
I created myNameBU.conf as a backup when I was editing the file.
QUESTION. Why is /private/etc/apache2/users/myNameBU.conf:
being referenced above ?
7.
I scanned my ports from preferences and found these two which I believe are what you stated they should be.
port 80 is html
port 8080 is html-alt
8.
I have modified this line and tried it both ways restarting apachectl each time.
AllowOverride None
AllowOverride All
9.
And here is a part of my httpd.conf.
excerpts.
httpd.conf
# User/Group: The name (or #number) of the user/group to run httpd as.
# It is usually good practice to create a dedicated user and group for
# running httpd, as with most system services.
User _www
Group _www
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
DocumentRoot "/Library/WebServer/Documents"
# Each directory to which Apache has access can be configured with respect
# to which services and features are allowed and/or disabled in that
# directory (and its subdirectories).
# First, we configure the "default" to be a very restrictive set of
# features.
<Directory />
    Options FollowSymLinks
    AllowOverride None
    Order deny,allow
    Deny from all
</Directory>
10.
I took a look at this too.
usr/bin
#path to httpd binary including options if necessary
HTTPD = "usr/sgin/httpd"
# pick up any environmental variables if test - f /usr/sbin/envvars; then ./usr/sbin/envvars
fi
STATUSURL = "http://localhost:80/server-status
11.
Just a reminder.
I started writing .php scripts with Netbeans IDE.
The programs ran: I got output in the brower. Things worked just fine !
I started writing .php scripts with DreamweaverCC.
The programs NEVER ran.
I have always gotten 'Unable to Connect"
Firefox/Safari can't establish a connection to the server at localhost.'
12.
QUESTION.
At one point I was on the phone with a member of the Adobe Technical Support Team.
They connect to my desktop (only) remotely. I am very cautious about this.
Could something have been inadvertently changed when they did this ?
They do need to connect through a PORT - yes ?
This is very frustrating and I am loosing days of work.
I want to get back to Web Development
I love Adobe products but this should not be such a huge obstacle.
When I called Technical support (after much troubleshooting individually and on this forum)
the fellow told me that the ONLY support FTP - not LOCALHOST.
This makes no sense. People develop 'locally' then put it ftp it in the production stage.
Again, I appreciate your assistance.

Unable to connect to a secure wireless network - Event ID: 8002 Task Category: AcmConnection..., Event ID: 11006, Event ID: 11006

Hi,
I have a Dell Latitude E6440 running Win 7
Enterprise 64 on a domain. It will connect to any unsecured network, and it can see the secured network in the list when I click the wireless connection icon on the system tray. When I go to manage wireless networks, the secured network does not show
up (and thus, I cannot delete the network to try to re-add it). Normally, we would add the secure network here. I click Add, give the name in the correct syntax, add the needed information (WPA/2-Enterprise, EAS or TKIP), and hit Next, it immediately returns
with "An unexpected error occurred". A similar thing happens when I hit Connect from the list of available networks that pops up when I open the system tray icon: it says it was unable to connect, when I hit troubleshoot, it says that it could not
identify the problem. The event log shows the error below. I haven't been able to find any resolutions here or elsewhere that address the fact that I can connect to unsecured wireless networks, but not secured wireless networks.
Other notable troubleshooting steps:
Uninstalled/Reinstalled wireless adapter with the latest driver
Other laptops are able to access the same secure wireless network
The first WLAN-AutoConfig error in the event log was Event ID: 12013, attempting a 802.1x authentication. Then Event ID: 11006; stating "Explicit Eap failure received". After a few days of alternating all 3 errors, they started to only error on
Event ID 8002.
Log Name: Microsoft-Windows-WLAN-AutoConfig/Operational
Source: Microsoft-Windows-WLAN-AutoConfig
Date: 6/4/2014 11:53:55 AM
Event ID: 8002
Task Category: AcmConnection
Level: Error
Keywords: (512)
User: SYSTEM
Computer: [COMPUTERNAME.DOMAIN]
Description:
WLAN AutoConfig service failed to connect to a wireless network.
Network Adapter: Intel(R) Centrino(R) Advanced-N 6235 Interface GUID: {f27af762-dff8-4927-84e0-7f4ade30dcc9}
Connection Mode: Connection to a secure network without a profile Profile Name: [SECURE NETWORK NAME]
SSID: [SECURE NETWORK SSID]
BSS Type: Infrastructure
Failure Reason:The specific network is not available.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-WLAN-AutoConfig" Guid="{9580D7DD-0379-4658-9870-D5BE7D52D6DE}" />
<EventID>8002</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>24010</Task>
<Opcode>191</Opcode>
<Keywords>0x8000000000000200</Keywords>
<TimeCreated SystemTime="2014-06-04T16:53:55.956762800Z" />
<EventRecordID>1475</EventRecordID>
<Correlation />
<Execution ProcessID="432" ThreadID="5348" />
<Channel>Microsoft-Windows-WLAN-AutoConfig/Operational</Channel>
<Computer>[COMPUTERNAME.DOMAIN]</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="InterfaceGuid">{F27AF762-DFF8-4927-84E0-7F4ADE30DCC9}</Data>
<Data Name="InterfaceDescription">Intel(R) Centrino(R) Advanced-N 6235</Data>
<Data Name="ConnectionMode">Connection to a secure network without a profile</Data>
<Data Name="ProfileName">[SECURE NETWORK NAME]</Data>
<Data Name="SSID">[SECURE NETWORK NAME]</Data>
<Data Name="BSSType">Infrastructure</Data>
<Data Name="FailureReason">The specific network is not available.</Data>
<Data Name="ReasonCode">163851</Data>
<Data Name="ConnectionId">0x6</Data>
</EventData>
</Event>

check this article:http://technet.microsoft.com/en-us/library/cc735927(v=ws.10).aspx
also could contact your domain administrator to ask for help.

Help, unable to connect

hello, my problem is that i have 2 computers at my house, mine and my mom's. my mom's computer is use the Linksys Wireless-G Broadband Router, and my uses the Linksys RangePlus Wireless Network USB Adapter that wirelessly connects with the Router. Lately its been unable to connect, when i go and try to reconnect i get other connections but not my moms. I got another Wireless Network USB and tryed that, and still wont connected...
so my question is... what can i do to connect my wireless adapter and rounter again?

Are you able to see the network name of your router ?
If yes, then what's the error message are you getting when you are trying to connect to the wireless network.

'Unable to connect' the number of free accounts can be enabled on this case has been reached

hello ! please someone help me
when i sign in icould ...'Unable to connect' the number of free accounts can be enabled on this case has been reached' heelp please

hello ! please someone help me
when i sign in icould ...'Unable to connect' the number of free accounts can be enabled on this case has been reached' heelp please
iPhone 5s, iOS 7.1.1

I've downloaded firefox for the first time. My internet works yet when I try and open the browser it says 'unable to connect'

I can't seem to get firefox properly running on my computer. I've installed it, I have internet connection, yet when I open a window and try to go on a site, it says 'unable to connect'

Hello Patrick O' D,
In my experience t here are two different problems with the speed of firefox on startup
# your os and setup
# firefox - and exactly what you use with it
Some factors will be down to your OS and for instance what does start up initially, many of those factors will affect other programmes/applications and not only firefox.
Some other factors depend on Firefox and how you set that up, I always like to have the option to using Firebug but realise it cold clash with other software or slow down firefox startup so I only enable it as I need it. see for instance: https://addons.mozilla.org/en-US/firefox/performance/

Unable to connect to Wifi when cellular data is on

As I understand it, I should be able to have both WiFi and Cellular data turned on, and the phone should default to WiFi when a preferred network is in range, and 3G when I'm out of range.
However, when I have cellular data enabled and I attempt to connect to WiFi, it always says "Unable to connect to network". As soon as I turn off cellular data, it connects right away. It does this both at home and at work.
If I enable WiFi (and connect) while in range, then enable cellular data, it will end the WiFi connection, but constantly pop up windows asking which network I want to join, only to tell me I can't connect to them when I try.
My workaround has been to turn off 3G and turn on WiFi when I get in range, and do the opposite when I leave, which means I'm doing this 4 times a day. Annoying to say the least.
Ideas? I am unable to use a static IP at work (I have seen some fixes using a static IP).

as far as i know there is no fix without using a staic IP however you might want to check with your Service Provider and see if you are eligible for an upgrade

Unable to connect when 3G is enabled....

Similar Messages

Maybe you are looking for