Unable to create a wireless network with my airport express. Please help!

I am trying to setup a wireless network with an airport express, and connect to it with my Macbook. I just bought both of these and haven't been able to get wireless to work.
I initially plugged the ethernet cable from my cable modem into the airport express and plugged it into the wall. The macbook detected it when I opened airport utility, but the express had a flashing amber light and I was unable to connect. I then unplugged the express and re-started the cable modem. This time, the airport express showed a solid green light -which should mean that it is working correctly. However, the macbook did not find the airport express device when i searched for it using airport utility. I am able to connect the macbook directly to the cable modem, after re-starting the modem, and access the internet so at least some of the systems are go.
Any ideas? Thanks in advance for your help.
Tom

Is the issue that you cannot access the 802.11n AirPort Express Base Station (AXn) with the AirPort Utility that is running on your Win7 PC? ... or that once you have configured the AXn, the PC is unable either to find the new wireless network or can find it but cannot connect to it?

Similar Messages

I am unable to join my existing wireless network with new AirPort Express

I am unable to join my existing wireless network with new AirPort Express.
I am using a DLink DI-524 Router, Windows 7 (64), and the AirPort Express.
AirPort Utility will not recognize the AEX wirelessly, it will only recognize it when it is connected by Ethernet. I can then configure the AEX and verify that the settings stick once disconnected and then reconnected. However, even after that, it will not recognize the AEX once disconnected from the Ethernet cable.
I followed the suggestions of several other threads on these forums. But I am unable to get the AEX to work.
Any suggestions? Thanks in advance.

Welcome to the discussion area!
It's almost always a security setting that causes problems when the Airport Express (AX) tries to join a third party wireless network. The AX usually does not "join" correctly and that's why you can't see it on your wireless network using AirPort Utility.
Using an ethernet cable is still the more reliable way to configure and adjust the AX, but if you are want to try to configure it using wireless, you must return the AX back to factory defaults as follows:
Power down the AX
Hold in the reset button +and keep holding it in+ as you plug the AX back in to power
Release the reset button after 10 seconds
When it is set to factory defaults, the AX broadcasts a wireless signal with a network name like "apple network xxxxxx" where the "x's" are either letters or numbers. You must look for this network by clicking on the fan shaped Airport icon at the top of the screen. If you don't see this network, then click Join Other Network to search that way. Unless you connect to this network, you will not be able to configure the AX using wireless.
Do you know the exact security type that your D-Link router is using? That is the key element in the process.
Open AirPort utility, click Manual Setup
Click the Base Station tab to establish a name for the AX, device password and adjust time zone settings
Click the Wireless tab
Wireless Mode....Join a wireless network
Wireless Network Name...must exactly match your D-Link wireless network name
Enable ethernet clients if you want the port to be active (your D-Link must be compatible with ProxySTA for this to work)
Wireless Security...exact setting of the D-Link network. WEP security causes a lot of issues. Try to use WPA/WPA2 Personal, which is far more secure.
Wireless Password...must match the D-Link network
Click the Music icon to enable AirTunes
Click Update to save settings
Any luck?

Extending an existing wireless network with an airport express

My wireless signal is quite weak in my room so I'm looking for a way to extend the range of the network by using an airport express. I understand i can't do this wirelessly but is it possible to run an ethernet cable from my existing router to the airport express in my room and then have a stronger signal in my room?
Thanks in advance!

Welcome to the discussion area, Aaron!
If you connect an ethernet cable from your existing router to the AirPort Express, and then configure the Express to "Create a wireless network" with the same name, security settings and password, this will in effect, extend your current wireless network.
The Express must be configured as a "bridge" to operate correctly on your network when you do this, meaning that the setting for Connection Sharing on the Express will be set to "Off (Bridge Mode).

Creating a wireless network using several Airport Express(es)

I would like to connect three AirPort expresses to my Sky Broadband router to create a new wifi network in my house. My router is in the basement and is connected into a hub which provides ethernet to the house. I would like to connect the AirPorts via ethernet to the router and create a single wifi network.
Can someone please tell me if this is possible and what settings the AirPorts should have. For instance, should I just extend the sky network using each AirPort or should I create a new network with one AirPort and then extend that with the others?
Many thanks
Terry

If each of the AirPort Express devices will be connected using Ethernet, you would configure them all exactly the same except for assigning different device names...AX1, AX2, AX3, etc.
Each Express will be configured to....
Create a wireless network
Same wireless network name on all devices
Same Radio Mode
Channel set at Automatic
Same wireless security setting
Same wireless network password
Very important....configure each Express in Bridge Mode
Post back if you need more details

Extend wireless network with multiple airport express and netgear powerline

I currently have the following network configuration:
1. Using ATT u-verse (2-wire 3800HGV-B "modem") to internet
2. Disabled the u-verse modem wireless router, and have connected an Apple Time Capsule wireless router (on a DMZ)
3. Have four Netgear XAVB5001 powerline adapters connected to the time capsule (for our iMac desktops and the Apple TV)
4. Have an Airport Express wirelessly connected to the time capsule to extend range (for our iPhones and iPad)
All this is currently working. What I would like to do is the following, keeping 1-3 above the same:
4. Connect the airport express to the time capsule via Netgear XAVB5101 powerline adapter (instead of wirelessly connecting to the time capsule as it is today) and use it to extend the wireless range of the time capsule
5. Add ANOTHER airport express to the time capsule via powerline adapter (and extend the wireless range elsewhere in the house).
Does anyone have any experience with this kind of setup and can assure that it would work? (I'm trying to decide whether to spring for a couple more powerline adapters and another airport express)
Thanks in advance!
Dave

I had a VERY similar problem: I was trying to extend my wireless network using a hardwired ethernet connection from Airport Extreme to my Time Capsule. Every time I plugged in the wire to the TC, everything disappeared. Unplugged, and boom. Came back.
Here's how I solved it:
Go into Airport Utility and select the unit you are trying to use as a wireless extender and choose to edit it. Then, on the wireless tab select CREATE a wireless network. But, give it the exact same name and password. This is completely counter-intuitive. You would think to choose EXTEND, but this would be wrong. Next choose the network tab. And, select Router mode to Bridge (off).
By choosing the same name and password, your phone, laptop, etc. will think it's on the same network and move seamlessly from one to the other.
See if this fixes your issue. Fixed mine instantly. AND, it only took 3 painstaking hours of checking ethernet connections and rewiring jacks, etc. to figure it out. LOL

Creating and Extended Network with 2 Airport Express Units

I had an extended network using 2 express units but one of them broke. The old network was setup with an older version of Airport Utility and I can't seem to repeat the set up a new network with the new express unit I have bought.
The simple setup procedure using Airport Utility 5.5.1 only appears to allow you to 'join' the remote Express unit to an existing network, there is no 'extend remotely' option.
I remember doing it last time by creating a WDS network which agrees with instructions I have found here - http://broadcast.oreilly.com/2009/03/taming-an-airport-express-wds.html
I set up the first Express as a base station with a network and select 'Participate in a WDS network' and 'Allow this network to be extended' under the wireless tab. Under the WDS tab I 'Allow wireless clients' and add the hardware address of the second express unit.
I then update the express unit but I get a WDS error which states, "This Airport wireless device is set up as part of a WDS network but no other AirPort wireless devices were found."
This seems to be a chicken and egg situation.
Any help would be appreciated.
Alan

Alan, welcome to the discussions!
It appears that you want to set up a WDS arrangment, correct?
But, I can't figure out whether you want to configure it with a "base" and two "remotes", or whether you want to configure it with a "base", "relay" and "remote"
Can you clarify? I'll send you a link with instructions from forum expert user Tesserax with step by step instructions. Just need to know what set of instructions to send.

How to extend range of my wireless network with an Airport Express connected by ethernet with Airport Utility 6.0

Hi everyone,
I have AirPort Express 802.11n (1st Gen) firmware 7.6.1, that is connected to my main wifi base station (a TimeCapsule) by ethernet. I would like to extend the range of the Wifi Network but am not clear on how to do so using the new interface of Airport Utlity 6.0.
Does anyone have any tips on how to do this?
BR
AK

Hi Everyone!
Many thanks for the tips. I have downloaded 5.6 and have set my Airport Express in the "Extend a wireless network" mode. I was still having a few problems with the quality of the wifi connection in different parts of my apartment (by no means a very large one, but walls seem to be made of extra dense concrete here in Singapore) and went out and bought a few powerline adapters by TP Link (http://www.tp-link.sg/products/details/?categoryid=1862&model=TL-PA211#spec).
If you don't mind a slightly long post, I would be very grateful for any tips:
My setup is now as follows:
Main room
Time Capsule - connected to a Cisco DPC3925 Modem (http://www.cisco.com/web/consumer/support/modem_DPC3925.html) both connected to a TP Link adapter 1.
iMac - connected via Ethernet to TP Link adapter 2 and wifi enabled
Airport Express 1 - connected by Ethernet to TimeCapsule (and thus TP Link adapter 1) used to stream audio to a stereo that doesn't have an optical cable input. Since it is an Ethernet connection, I have wifi turned off.
Apple TV 1 - connected by Ethernet to TimeCapsule (and thus TP Link adapter 1)
Bedroom A
Airport Express 2 - connected via ethernet to TP Link adapter 3
Bedroom B -
Apple TV 2 - connected by Ethernet to a TP Link adapter 4
After following the tips on setting up the extended wifi network, I find that when I use a wireless client (e.g. iPad, Macbook air, etc) in either Bedroom B or Bedroom C (both don't have wifi in the room) the connection is very poor. Even more odd is that the connection in Bedroom A, one that does have Airport Express 2. To be clear when I mean very poor, I mean Skype/facetime skips frames and freezes... this doesn't happen when I am in the main living area.
I would be very grateful for tips on how to set up the most robust network given the configuration above. Specifically, I am wondering about:
When I select Extend a wireless network option on Airport Utility 5.6 the summary page states that it is connecting using "Wireless Network" vs what I would expect it to say "Ethernet connection".
Is there any advice on whether to enable 5Ghz network and if so, should I try to use that for the various wifi clients?
Does anyone know if I can somehow use Apple products to extend the reach of the Cisco DPC3925? Frustratingly the signal is quite strong (compared to Apple routers), but I cannot properly stream audio/video if that wifi network is used (as my iMac that hosts the content is on the Apple one... and I'd have to walk over to switch it to the Cisco one).
Any other tips would be much appreciated!
Cheers!
AK

I have an airport extreme and am trying to extend the range of the wireless network with an airport express. I set it up with the help of apple support, both lights are green on both airports, but the range didn't change. What could be wrong?

I am trying to extend the range of my wireless network by adding an airport express to an airport extreme. I configured it with the help of apple support, but it hasn't changed the range that I can access the internet wirelessly in my house. What could be the problem? Does weather affect the wireless network??

So, on the Extreme you checked the box to "allow this network to be extened" ?
Correct?
And on the Express, you set it up to "Extend a wireless network" ?
Correct?
See this Apple article and see if you missed anything...
http://support.apple.com/kb/HT4145
To learn about other options for expanding your Wi-Fi base station wireless network and things you should consider before expanding your network, click here.
Set up: Components of an extended network
➊ Primary Wi-Fi base station (this is the base station connected directly to the Internet)
➋ Extended base station
Configuring a wireless extended network
To create a wireless extended network, you must place any extended Wi-Fi base stations within range of the primary Wi-Fi base station.
Start with the device that will be configured as the primary Wi-Fi base station. Then configure your extended Wi-Fi base stations, ensuring that each is within direct range of the primary Wi-Fi base station.The physical location of extended Wi-Fi base stations will vary according to the building environment and may require some experimentation.
If you have configured your Wi-Fi base stations in the past, it may be helpful to do a factory default reset of each Wi-Fi base station that will be part of the wireless extended network before you begin.

Cannot create a WDS network with two Airport Express

so i have one airport express here at my parents house acting as a wireless router. i brought a second express from my house and my playstation3 and want to connect the ps3 via Ethernet, i reset my express from home by holding the small pin-sized button. i open up airport utility choose the default named airport express, hit continue>switch>name it and give it a password>I want it to join my current network>Extend the Range of my Network>Chose my network (Twice)>watch the 'configure' WDS screen. then i get this:
http://farm4.static.flickr.com/3632/3420465586a2f1864300o.png
both expresses have been recently updated with 6.3 firmware and i'm accessing both wirelessly. i've tried over and over again resulting in the above image, can anyone please help?
btw there is no 'allow this network to be extended' box.

Psych,
Do the setup hard wired to your Mac - so connect an ethernet cable between your Mac and the AX you're trying to set up. Do the setup as usual, and once the configuration has written to the AX, restarted and you have a green light, you can remove the cable and connect wirelessly.
Sometimes, and for some reason, the configuration has problems writing to the AX wirelessly, especially after a reset.

Having trouble with extending an Apple wireless network with a AirPort Express

Trying to extend the range of my AirExtreme with a AirExpress:
I get stuck when the AirPort Utility ask is I'm sure I want to switch networks. if I select switch I loose the AirExtreme. If I select don't switch it take me back to the beginning. Any help will be appreciated.

You have to "switch" networks to be able to pick up the signal from the Express and configure it with new settings.
Once the Express is configured it will become part your existing network when you see a green light.
Then, switch back to your regular wireless network on your Mac and everything will be on the same network

Extending airport express wireless network with another airport express

I am trying to set up another airport express to my existing airport express at home so I can extend the wireless range and also to connect my printer (to my second airport express) so I can have a shared wireless printer. Is this possible? If so, can someone assist me on how to set this up?
Thanks.

Try the following ...
AirPort Express Base Station (AX) - WDS Setup
"Factory Reset" the AX base stations
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
(Note: To facilitate setting up the base stations, place them in near proximity of each other during the setup phase. Also record the Apple IDs of each base station that will included in the WDS as these will be required during setup.)
Main Base Station Setup
(Note: The AX connected to the Internet will be assumed to be the main base station in the WDS.)
Either connect to the AX's wireless network or by temporarily connecting directly, using an Ethernet cable, to the Ethernet port of the AX, and then use the AirPort Admin Utility to make the following settings.
WDS Tab
1. Enable this base station as a WDS: main base station (checked)
2. Allow wireless clients on this base station (checked)
3. Click "+" to add Remote/Relay Base Stations.
3a. Select the Base Station that you want to be the WDS Remote/Relay.
3b. AirPort ID: <verify that this is the correct MAC address for the Base Station you are adding as a Remote/Relay.>
3c. Auto configure as a WDS remote base station (checked)
3d. Click "OK."
4. Verify that the Remote/Relay Base Station has been added to the list.
5. Click "Update," and then verify the settings for the Remote/Relay.
5a. Allow wireless clients on this base station (checked)
5b. New network name: <verify that this is the same as the network name as the main base station>
5c. TCP/IP: Configure using DHCP
5d. Base Station Password: <the Remote/Relay Base Station password>
5e. Confirm: <same as previous step>
5f. Click "OK."

How do I extend a netgear wireless network with an Airport Express?

I can get the Airport Express to join the network, but not extend it. I am trying to extend my network to improve the signal to my Apple TV. I have read in some places that his can't happen. I have a Mac as my computer.

Any idea how to merge the Netgear extender to the primary Netgear network?
You have a question for Netgear Support here since your question involves two Netgear products.
This link would be a logical place to start:
Contact Support - Netgear
While it is possible that someone on an Apple forum might know how to do this....it is also unlikely that they will see this post and respond. You can certainly wait to see if someone responds here if you wish.....but if it were me, I would contact Netgear about a Netgear question.

Extending wireless network with an aiport express

I have a netgear wireless router set up in my house on the second floor, but my room being located on the first floor i get a poor signal so i bought an airport express to extend my network. i tried going through the aiport exress setup assistant but that wouldnt work, so i ended up hooking it to my netgear router on the second floor to set it up in airport admin utility and then brought it back down to the first floor. my itunes worked with the speakers for about.. ten seconds then stopped. and my signal is just as weak as before.. any suggestions?

Unfortunately, it is simply not possible to use an Airport Express to wirelessly "extend" the wireless range of any model of Netgear wireless router. Netgear's wireless routers do not support Apple's implementation of a wireless distribution system (WDS), which is a necessary requirement for setting up an extended wireless network with the Airport Express. And no - it doesn't work the other way around either (Airport Express as base station, Netgear wireless router to "extend").
It sounds like you did successfully configure your Airport Express to "join" your existing wireless network - which will allow you to print and stream iTunes to the Airport Express. The problems you are having with Airtunes "hanging" on your Mac are almost certainly due to the poor wireless signal quality problem that you are already aware of.

Can I extend my network by connecting one of my airport express devices to my airport extreme via an ethernet cable? I have CAT5 cable throughout my house but have a wireless network w/ 3 airport expresses

Can I extend my wireless network by connecting one of my airport express devices to my airport extreme via an ethernet cable? I have a wireless network with 3 airport expresses and 1 airport extreme functioning as the base station. I have CAT5 throughout my house.

Welcome to the discussions, mib88!
Can I extend the network a second time with another Airport Express...
The short answer would be no. If you want more details, please continue to the next paragraph.
Apple's "extend a wireless network" works just like the hub and spokes of a wheel. Your main hub is either the Time Capsule or the AirPort Extreme and the AirPort Express is at the end of a spoke. You can add more devices at the ends of other spokes, but these devices will communicate directly to the hub, not to another device at the end of a spoke.
Apple does offer an option which is is known as a "static WDS", which can consist of a "main", "relay" and "remote" device. The problem here is that this type of setup has two huge drawbacks:
1) All of your faster "n" devices will drop down to much slower "g" speeds
2) The bandwidth or speed capability on the network will drop down to only 25% of the original bandwidth with a "main", "relay" and "remote" on the network.
Don't think you want this on your network. Your best option is to connect the new AirPort Express to the "hub" using an ethernet connection. If you can't run the ethernet cable, take a look at a pair of ethernet powerline adapters to accomplish the same task by sending the ethernet signal over the AC powerline in your home.

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

Unable to create a wireless network with my airport express. Please help!

Similar Messages

Maybe you are looking for