Unable to enable HBA Card in the Cisco UCS c22 m3 server

Hi All,
I need your help desperately to setup the cisco ucs c22 m3 server in our environment. We have a C22 M3 server and I did the basic config of CIMC and we have a LSI megaraid controller connected to one of the PCIe and the other PCIe has a dual port 8gb HBA card. We installed the RAID and we can see the LSI Megaraid controller. But I cannot see the HBA card and there is noo light near the card. I hope I need to enable something so that the card should work. I tried enabling in the BIOS menu I can see the PCIe slot is enabled but I am unable to see the HBA functioning. Couldyou pleasehelp me to resolve this.

Dear Manuel,
Thanks for replying me. See the answers for your queries.
What kind of HBA card are you trying to use?
If I am not wrong we are using "Qlogic QLE2562, 8Gb dual port Fibre Channel HBA".
How many CPUs do you have installed on your server?
I opened the box and saw only 1 CPU installed. But the solution is given by CISCO pre sales. We have 2 PCIe slots configured. One for LSI RAID controller and the other with dual port Fibre Channel HBA.
Awaiting your reply.
Thanks and Regards,
Jaffer Ali

Similar Messages

Cisco UCS C210 M1 server certified for Unified Communications

Hello:
Our VAR is telling us that HP and Cisco are splitting up. We're an HP shop today and the MCS 7800-H series routers were a perfect fit. Our VAR is now telling us we have to go with the rebranded IBM systems. BUT I would like to avoid the IBM servers. And the Cisco servers look attractive. But I've been unable to determine if the Cisco UCS C210 M1 server is certified for various Unified Communications applications (Communications Manager, Unity, Cisco Emergency Responder, ICM, CVP, etc.).
Has anyone heard of any Unified Communications deployments on UCS hardware?
Thanks,
Ken

Mr. Schroeder:
Thank you for the information. Timing is everything. We'll likely have to order our equipment in May of this year. I'd love to start getting Cisco UCS hardware in. Oh well... maybe next year!

Can the Cisco UCS 6120XP direct attach the EMC CX4-120 by fibre protocol ?

Hi all
I have two question for Cisco UCS
Q1: Can the Cisco UCS 6120XP direct attach the EMC CX4-120 by fibre protocol ?
Q2: I know the UCS 61XX Series support the Cisco SAN Switch(MDS).But we are only Brocade san switch ,
so UCS 61XX Series supoort Brocade san switch ?
Thanks , I really want to know the information .

Q1: The 6120s run in NPV (N_Port Virtualization) mode which means it acts as a proxy for the blade vHBAs and doesn't participate in flogi (fabric logins). When a fabric switch runs in this mode it requires an uplink to a faber switch for flogi and zoning. Due to this you cannot direct attach the the 6120 to an array's front-end fiber ports.
Q2: Yes you can uplink the 6120 to a Brocade fabric as long as the Brocade supports NPIV.

You cannot sign in to the Cisco Unified MeetingPlace Web Server interface using preconfigured system profiles

Hi
I recently upgrade tp 7.0.3 from 7.0.2.
While upgrade i found that i am not able to login to the web server with the admin id "admin" default created in the application server.
The same id i can login to application server , but not in wewb server.
I am getting the mentioned error "You cannot sign in to the Cisco Unified MeetingPlace Web Server interface using preconfigured system profiles".
However if i create a new user in application server and tried logging with the same in the web server it is working fine..
is it a known behaviour wirh the upgrade or i m facing some issue.
Hope i can find a solution here.
Regards
RC

RC,
This behavior is stemming from a change in MP 7.0 MR2 to disable the MPWeb login for system profiles. This was an internal change made by the developers to restrict the log on to the MPWeb page by the default accounts created in MeetingPlace upon installation. The change now displays this error when the admin account is attempted to be used for MPWeb login, as you experienced-
Error:[22953] You cannot sign in to the Cisco Unified MeetingPlace Web Server interface using preconfigured system profiles.
You should be able to log into MPWeb using any other user profile that you have either created manually or pulled in from LDAP/Active Directory. You just cannot use the admin account. This is reserved for login to the MP Application Server Administration page only. I am going to work to get this information added to the MP 7.0 documentation with a note for changed behavior in MR2 and above. Here is the note from MP 8.0 documentation-
Note: You cannot use this preconfigured admin profile to access the Cisco Unified MeetingPlace Web Server interface. Instead enter the User ID and password information from one of the other user profiles that have system administrator privileges to sign in to the Web Server.
Please let me know if you have any further questions.
Thank You,
Gerry

Cisco UCS C220 M3S Server OS random shutdowns

Hello good day, I am facing some issues with the Cisco UCS indicated in the subject, I have created a Raid 1 beetwen 2 HDD's of 1 TB each one, also upgraded the firmware of the UCS with the 2.0(3f) HUU tools, and upgraded everything. Then I installed Windows Server 2012 R2 Eval version (I have a proper license to install but wanted to test the OS first). Now some times the OS/Server just shutsdown, and whenever I go in to the Web GUI to check it out, it's actually powered down, I have checked the "Faults and Logs" --> System Event Logs, and I can see this happening:
*The timestamp is from below to the top on both logs*
MAIN_POWER_PRS: Presence sensor, Device Removed / Device Absent was asserted
Microsoft OEM event data record, Record type: DD, Sensor Number: 0A, Event Data: 00 00 00, Raw SEL: 37 01 00 35 0A 00 00 00 00
(About this message with the HEX Values, it's always repeating it self with other values)
System Software event: OS Stop sensor, OS Graceful Shutdown was asserted
In the IMC Log this is what showed when it powered down:
Bridge.c:1484:audit Resp:0x0
Bridge.c:1478:audit from:kcs Fn:0x0 Cmd:0x6 Data: 0x30 0x4
obj/../../src/BiosSecureBootAgent.cc:101:BiosSecureBootAgent --> m_valid_state = [ 0 ] #012 m_enable_state = [ 0 ] #012 m_setupMode_state = [ 1 ] #012 m_secureBoot_state = [ 0 ]
obj/../../src/BiosSecureBootAgent.cc:63:get=uefiSecureBootState Received
bootordermgnt.cpp:2392:WriteBIOSDeviceCfg: Successfully renamed file: /mnt/jffs2/ConfigPolicy.xml.bak to /mnt/jffs2/ConfigPolicy.xml
bootordermgnt.cpp:1310:StoreDeviceCfg: Successfully renamed file: /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT.bak to /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT
bootordermgnt.cpp:2392:WriteBIOSDeviceCfg: Successfully renamed file: /mnt/jffs2/ConfigPolicy.xml.bak to /mnt/jffs2/ConfigPolicy.xml
bootordermgnt.cpp:1310:StoreDeviceCfg: Successfully renamed file: /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT.bak to /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT
bootordermgnt.cpp:2392:WriteBIOSDeviceCfg: Successfully renamed file: /mnt/jffs2/ConfigPolicy.xml.bak to /mnt/jffs2/ConfigPolicy.xml
bootordermgnt.cpp:1310:StoreDeviceCfg: Successfully renamed file: /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT.bak to /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT
bootordermgnt.cpp:1367:No Precision Boot DB exists..migrate old relase configuration to Precision Boot format!
sanluis1/platform.c:116:platform_event_enable_tick_end: Configuring IR from CIMC
(A bunch of these with other values) common.c:945:Enabling sensor scan for sensor 0x85.
lv_dimm.c:403:[handle_event_enable_tick]enable sensor event
lv_dimm.c:220:[transition_function]Transition to [High Voltage Mode] Success
lv_dimm.c:200:[transition_function]Starting Transition to [High Voltage Mode] from [Unknown Mode]
(A lot of these with different values) common.c:940:Disabling Sensor scan for sensor 0x89.
lv_dimm.c:129:[lpc_reset_seen]LPC Reset Count is Different [0x15:0x16] Asserted LPC Reset Seen
selparser.c:678: # 1D 03 00 00 01 02 00 00 DB F7 EF 54 20 00 04 25 05 00 00 00 08 00 FF FF # 31d | 02/27/2015 04:51:39 | CIMC | Entity presence MAIN_POWER_PRS #0x05 | Device Absent | Asserted
Received event_ipmi_power_state_change Event (type=4, size=0)
video_trigger.c:262:Sending event_ipmi_power_state_change (OFF) .
WatchdogTimer.c:1467:Current Configuration of Watchdog timer is now stopped.
Pilot2SrvPower.c:466:Blade Power Changed To: [ OFF ]
<5>[se_pilot2_wakeup_interrupt]:2561:USB HS: VDD Power = OFF
<6>drivers/bmc/usb/usb1.1/se_pilot2_udc_usb1_1.c:2540:USB 1.1 is now disconnected.
<5>drivers/bmc/usb/usb1.1/se_pilot2_udc_usb1_1.c:2288:USB FS: VDD Power WAKEUP- Power Good = OFF
<7>[slp_state_isr]:117:Signals SLP3n[ Asserted ] SLP5n[ Asserted ]
<6>[platform_power_state_irq_handler]:18:VDD_PWR_GOOD: Deasserted
In the event viewer of the Windows Server 2012
This is the UCS specifications:
CPU 1: Intel(R) Xeon(R) CPU E5-2609 v2 @ 2.50GHz
CPU2: Intel(R) Xeon(R) CPU E5-2609 v2 @ 2.50GHz
Memory: 16 GB
There is something really itching, is it because I have Evaluation version of the Windows Server...?
Regards.

Ok, I feel kind of dumb now, I have checked the tech evaluation page on Microsoft, and if it's not connected to the internet it will not inherit the three months evaluation trial, which I thought would come activated already, and only allows you up to 10 days grace period with the rearm command .... :/
The process C:\Windows\system32\wlms\wlms.exe (WIN-UDPFG5O0K37) has initiated the shutdown of computer WIN-UDPFG5O0K37 on behalf of user NT AUTHORITY\SYSTEM for the following reason: Other (Planned)
Reason Code: 0x80000000
Shutdown Type: shutdown
Comment: The license period for this installation of Windows has expired. The operating system is shutting down.
This is what made me check it out today, I will connect it to the internet and let it activate... Meanwhile the command for the 10 days grace is:
Slmgr /rearm
Shutdown –r
Like always.

7210 Unable to see HBA card

Hi, I'm intent to using FC rather than network. Already upgrade the storage to 2010.02.09.1.0,1-1.15 version.
Then, i install a 2x Qlogic HBA ( SG-XPCIE1FC-QF4), but the storedge unable to recognized it. From BIOS i can see the Qlogic have been detect.
From shell mode, run cfgadm ( the HBA card not detect).
Here some logs,
boot with "-v" ( Able to see the HBA detect as qlc0 and qlc1)
PCI Express-device: pci10de,377@a, pcieb2
pcieb2 is /pci@2,0/pci10de,377@a
PCIE-device: pci1077,142@0, qlc0
qlc0 is /pci@2,0/pci10de,377@a/pci1077,142@0
PCI Express-device: pci10de,375@b, pcieb7
pcieb7 is /pci@2,0/pci10de,375@b
PCIE-device: pci1077,142@0, qlc1
qlc1 is /pci@2,0/pci10de,375@b/pci1077,142@0
fp0 is /pci@2,0/pci10de,377@a/pci1077,142@0/fp@0,0
fp2 is /pci@2,0/pci10de,375@b/pci1077,142@0/fp@0,0
But after fully up.. unable to see tha HBA cards. So i cannot create the FC target devices as not HBA shown up.
Please Help

Hi,
You know which file should i modified.. i already check /etc/driver_aliases, seem all aliases is there, modinfo currently load all the qlc module
and prtpicl already see the devices also /dev/cfg which already create c8 with HBA symbolic links.
Im now, it just the HBA wont bind to driver.. maybe cause the file you mention.

Cisco UCS C220-M3 Server doesn't boot after adding Intel I350 Quad Port NIC

Hello,
We have purchased 2 Cisco UCS C220-M3 rack mounted servers (Single Processor) that have a dual port I350 LOM. We also purchased two Intel I350 Quad Port NICs to expand the available ports on each server from 2 to 6.
The problem we are facing is that the server will not complete the boot process unless we disable either the LOM or the Quad Port NIC. We have tried numerous settings in the BIOS area but we haven't managed to have them both working.
The I350 Quad Port NICs are from Intel and not from Cisco and we are running the latest FW/BIOS on the Servers as of March 10 2015.
We have followed the steps described in the installation guide to install them.
Could you provide some light in this situation please, what are our options?
P.S. Although the LOMs are I350, the MAC Address Vendor is Cisco, is it possible that Cisco servers accept only Cisco Branded Expansion Cards?
Thank you,
George

Hi Shawn,
At least I'm not the only one having the same problem!
You are trying to use the cards with the LOMs enabled?
Which screen are you referring to in the first paragraph of your message?
Mine sits in BIOS POST for about 10 minutes and then resets itself....
We are also waiting for an answer from Cisco, so any findings/news will be posted here.
Thanks,
George

Unable to enable disk quotas in workgroup manager, X.4.8 server

I am trying to enable disk quotas in workgroup manager for our open directory users with mobile accounts.
I select "sharing" ---> all ---> drive that home directories are stored on ---> select "Enable disk quotas on this volume."
I am able to click the tab but when I attempt to save it gives me "unable to save changes." How can I save the changes? Do I have to use the CLI for this?
This is similar to this previous unsolved question on the boards: http://discussions.apple.com/thread.jspa?messageID=2495400
I'm not trying to make any other changes when I'm saving this, and am authenticated as the directory admin. Any help is a big help!

Nevermind, I found the answer in the archives after much searching. Went in via CLI and deleted the files below...voila! Disk quota goodness ensues and all is well.
full thread here:
http://discussions.apple.com/thread.jspa?messageID=2859843
"I answer my own question. I deleted the two files ".quota.ops.user" and ".quota.user" at the root level of each disks and now I can activate disk quota."

CAD Problem: Lost connection with the cisco unified ccx application server

I have two locations in our help desk area that consistantly loose connection. I checked the network and we ran new cables. Still having the same issue. They have connectivity to everything else when they loose connection to CAD so I believe there is something going on with the program itself. I have attached the logs from both. There is nothing else that lives on their subnet.
There are 2 servers, the primary 172.29.0.22 and the secondary 172.29.0.23. The Primary is the active server so it is in the same building as the agents.
Can anyone please advise? any help would truly be appreciated!

Hello DJ,
Thank you for replying. No nothing else lives on their subnet.
There are 2 servers, the primary 172.29.0.22 and the secondary 172.29.0.23. The Primary is the active server so it is in the same building as the agents.
I am completely stumped. I have no Idea why this is occuring.

Mac-Address Locking on ML-1000 for the Cisco 15454

Does anyone know if you can do mac-address locking on the ML-1000 card on the Cisco 15454. I would like to enter the command "mac-address-table secure", but it does not look like it is possible to do this.
Thanks,
Eric

The command is not supported on the ML-1000 card.

I'm trying to purchase a free app and my cc keeps declining.... It always works but now it's asking me for information and saying they are unable to process credit cards .. Can someone help?

II'm trying to download an app that's free. it keeps sending me to my credit card information and at first it said it declined, now it's saying it's unable to process credit cards at the moment and to try later. Is this normal? Can someone help please?

Periodically when you purchase anything from iTunes or download a free app it reverifies your credit card. A "declined" message comes from your card issuer; iTunes Store is just a passthrough of that message. So you need to contact your issuer to resolve it. Although at the moment it sounds like the problem is with your issuer's network.

Unable to enable routing in 3750x switch

im unable to enable ip routing in the WS-C3750X-24T-L switch. Tried with SDM prefer routing option but still same issue.
Can some suggest on this?
MOdel: WS-C3750X-24T-L
IOS :flash:c3750e-ipbasek9-mz.122-55.SE5.bin
sh license
Index 1 Feature: ipservices
        Period left: 0 minute 0 second
Index 2 Feature: ipbase
        Period left: 0 minute 0 second
Index 3 Feature: lanbase
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Priority: Medium
        License Count: Non-Counted
regards,
Ezra.

Index 3 Feature: lanbase        Period left: Life time        License Type: Permanent        License State: Active, In Use
You don't have the license to run routing.

Ask the Expert: Cisco UCS B-Series Latest Version New Features

Welcome to this Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the Cisco UCS Manager 2.2(1) release, which delivers several important features and major enhancements in the fabric, compute, and operational areas. Some of these features include fabric scaling, VLANs, VIFs, IGMP groups, network endpoints, unidirectional link detection (UDLD) support, support for virtual machine queue (VMQ), direct connect C-Series to FI without FEX, direct KVM access, and several other features.
Teclus Dsouza is a customer support engineer from the Server Virtualization team at the Cisco Technical Assistance Center in Bangalore, India. He has over 15 years of total IT experience. He has worked across different technologies and a wide range of data center products. He is an expert in Cisco Nexus 1000V and Cisco UCS products. He has more than 6 years of experience on VMware virtualization products.
Chetan Parik is a customer support engineer from the Server Virtualization team at the Cisco Technical Assistance Center in Bangalore, India. He has seven years of total experience. He has worked on a wide range of Cisco data center products such as Cisco UCS and Cisco Nexus 1000V. He also has five years of experience on VMware virtualization products.
Remember to use the rating system to let Teclus and Chetan know if you have received an adequate response.
Because of the volume expected during this event, our experts might not be able to answer every question. Remember that you can continue the conversation in the Data Center community, under subcommunity Unified Computing, shortly after the event. This event lasts through May 9, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hi Jackson,
Yes its is possible. Connect the storage array to the fabric interconnects using two 10GB links per storage processor. Connect each SP to both fabric interconnects and configure the ports on the fabric interconnect as “Appliance” ports from UCSM
For more information on how to connect Netapp storage using other protocols like iSCSI or FCOE please check the url below.
http://www.cisco.com/c/en/us/products/collateral/servers-unified-computing/ucs-6100-series-fabric-interconnects/whitepaper_c11-702584.html
Regards
Teclus Dsouza

Cisco UCS model to match Dell R900

I am trying to replace existing Dell R900 ( 1 TB of drive space, 24GB RAM and 2 Quad core CPU ) with Cisco UCS but not sure which model I should go with. any response will be appreciated!

It looks like the Dell R900 is a rack server, so if you are looking for something similar, you may want to try the C460-M4:
Specifications at a Glance
Four rack-unit (4RU) chassis
Either 2 or 4 Intel® Xeon® processor E7-4800 v2 or E7-8800 v2 product family CPUs
Up to 6 terabytes (TB)* of double-data-rate 3 (DDR3) memory in 96 dual in-line memory (DIMM) slots
Up to 12 Small Form Factor (SFF) hot-pluggable SAS/SATA/SSD disk drives
10 PCI Express (PCIe) Gen 3 slots supporting the Cisco UCS Virtual Interface Cards and third-party adapters and GPUs
Two Gigabit Ethernet LAN-on-motherboard (LOM) ports
Two 10-Gigabit Ethernet ports
A dedicated out-of-band (OOB) management port
*With 96 x 64 GB DIMMs when available.
http://www.cisco.com/c/en/us/products/servers-unified-computing/ucs-c460-m4-rack-server/index.html
I hope this helps.
Let me know if you have questions, if none, please mark the question as answered.
-Kenny

WRVS4400NV2 IPS now blocking Cisco IPS Auto Update Server

Yesterday I noted that my ASA5505 AIP-SSC5 card was failing to auto update as it had been doing without issue for months. I looked in the logs and the IPS was showing an HTTP Error when attempting to update. I checked and nothing had changed in the IPS configuration. Then, on a hunch, I checked the IPS log of the WRVS4400N which is the edge router for the small business network.
The WRVS4400N IPS was blocking connections with the cisco auto update server because it detected an RPC Anomaly in the traffic. So apparently, something has changed in the cisco IPS auto update server (https://198.133.219.25//cgi-bin/front.x/ida/locator/locator.pl) response that the cisco small business router misidentifies as a threat. . .
FYI-I also posted this issue to the small business router community discussion forum.

Yesterday I noted that my ASA5505 AIP-SSC5 card was failing to auto update as it had been doing without issue for months. I looked in the logs and the IPS was showing an HTTP Error when attempting to update. I checked and nothing had changed in the IPS configuration. Then, on a hunch, I checked the IPS log of the WRVS4400N which is the edge router for the small business network.
The WRVS4400N IPS was blocking connections with the cisco auto update server because it detected an RPC Anomaly in the traffic. So apparently, something has changed in the cisco IPS auto update server (https://198.133.219.25//cgi-bin/front.x/ida/locator/locator.pl) response that the cisco small business router misidentifies as a threat. . .
FYI-I also posted this issue to the small business router community discussion forum.

Unable to enable HBA Card in the Cisco UCS c22 m3 server

Similar Messages

Maybe you are looking for