Unable to enable SPDIF??? X-Fi XtremeGamer (non-PRO) w/ Digital I/O Module

JUnable to enable SPDIF? X-Fi XtremeGamer (non-PRO) w/ Digital I/O Module? I recently purchased the Digital I/O module in order to use SPDIF Out on my X-Fi XtremeGamer in order to send audio to my 5. receiver via digital coax.
However after hooking up my Digital I/O module to the flexijack (the one with the red light) I am unable to enable SPDIF.
I read and followed the directions listed here:
<a rel="nofollow" href="http://support.creative.com/kb/ShowArticle.aspx?sid=64440"]http://support.creative.com/kb/ShowArticle.aspx?sid=64440[/url]
The options that they tell you to set are simply are not there on my system.
I am running the most current drivers and console launcher that Creative has on their website.
I have been trying to get it to work both under Windows XP and Windows 7.
I have spent the last 3 hours beating my head on a wall, I hope someone can help me with this...
Thanks in advance for any suggestions!

Ah that's what I am afraid of.
Quoted from the article in your message: "For SB073X series : Supports Microphone-in, Line-in and Optical out connections. On a SB073X series card, this jack does not have the Digital-in function to support the Digital I/O Module. It does however connects to external digital audio devices that accept stereo PCM or compressed Dolby Digital/DTS Bitstream from the Optical output. This will require using a "Toslink to Mini Toslink" cable for connection only."

Similar Messages

  • Unable to enable DTS NEO:PC - X-Fi - Windows 7 - SPDIF

    I can enable DTS, but when I try to enable cinema or music mode it is grayed out.
    Near the bottom it says "DTS Neo:PC does not support the selected sampling rate. click the Change button and select either 44 kHz or 48 kHz.
    So I click on change, and the only sampling rate that is enabled is 48 kHz. ?
    Any thoughts?

    Ah that's what I am afraid of.
    Quoted from the article in your message: "For SB073X series : Supports Microphone-in, Line-in and Optical out connections. On a SB073X series card, this jack does not have the Digital-in function to support the Digital I/O Module. It does however connects to external digital audio devices that accept stereo PCM or compressed Dolby Digital/DTS Bitstream from the Optical output. This will require using a "Toslink to Mini Toslink" cable for connection only."

  • %ACL-7-ENTRY_DONOT_EXIST: acl.c:301 Unable to find an ACL by name "none".

    HI
    Since creating a Mobility Anchor between us and another compnay we are getting this message several hundred times a day %ACL-7-ENTRY_DONOT_EXIST: acl.c:301 Unable to find an ACL by name "none".
    https://supportforums.cisco.com/thread/2126701
    I've read on the above linke, looks like AAA Over Ride is annable on the AAA server.
    So we've enabled AAA Over Ride on the WLAN, this hasn't stopped the issue.
    The Mobility Anchor has 2 firewalls inbetween.  Everything is workign except for these messages, I do see them pop up on WCS Major Alerts, but the 3rd party have not reported any issues.
    They are using Win Server 2003 IAS boxes.
    Is this a problem or a bug?
    many thanks

    Craig:
    Both anchor and foreign on same version? (what version?)
    You try to compare the configuration of the WLANs and make sure it is the same on Anchor and Foreign.
    I've seen earlier some bugs with different messages. The bugs were related to different versions on anchor/foreign WLCs.
    Regards,
    Amjad
    Rating useful replies is more useful than saying "Thank you"

  • Unable to enable routing in 3750x switch

    im unable to enable ip routing in the WS-C3750X-24T-L switch. Tried with SDM prefer routing option but still same issue.
    Can some suggest on this?
    MOdel: WS-C3750X-24T-L
    IOS :flash:c3750e-ipbasek9-mz.122-55.SE5.bin
    sh license
    Index 1 Feature: ipservices
            Period left: 0  minute  0  second
    Index 2 Feature: ipbase
            Period left: 0  minute  0  second
    Index 3 Feature: lanbase
            Period left: Life time
            License Type: Permanent
            License State: Active, In Use
            License Priority: Medium
            License Count: Non-Counted
    regards,
    Ezra.

    Index 3 Feature: lanbase        Period left: Life time        License Type: Permanent        License State: Active, In Use
    You don't have the license to run routing. 

  • 4.0EA1 Diff Carts Unable to compare carts when connected as non-owner

    Unable to compare carts when connected as non-owner.
    Background:
    We have 2 identical environments and I want to compare their objects. I login as user3 with select_catalog_role
    Steps:
    Connect as user3 then populate two carts. One selecting tables from schema1 another cart selecting tables from schema2. Now run Diff Carts.
    Behavior:
    Text field for Connection is disabled: When there are 2 carts loaded Diff Carts does not allows to compare to Connection. This field remains disabled even when one of the cart tab is closed and Diff Carts is started again.
    Unable to compare:  Diffing with another cart has connection issues. Diff report shows error (table icon with exclamation mark).
    For Schema1 it says
    <schema1>.<table_name> using null connection.
    Unable to compare objects.
    Ensure that you have the required permissions. 
    You must own the objects or have select_catalog_role.
    For schema2 it says
    <user3>.<table_name> using null connection.
    It is trying to find table for user3 although owner is schema2 in cart2

    I am able to reproduce your issues with the diff from cart ui and have filed a bug and identified a fix for it.  The issue is that if the combo box is disabled, it remains disabled and the only way to get it enabled again is to restart sqldev. 
    When diffing between two carts, the connection that is used for the add to cart is used for the authorization so if you add it to the cart from user3, user3 will be used for permissions.  This is the intended behavior.  have also filed a bug for the error message with "null" for the connection.

  • HP Photosmart Plus B210 unable to enable web service

    I just moved this printer from one location to another. I have the printer connected to the network - but I am unable to enable web services. I just keep getting a Service Connection Error that says "There was a problem connecting to the Server."
    I've looked for solutions on the HP site - but none of them have worked for me.
    Any help is greatly appreciated!
    LuAnn
    This question was solved.
    View Solution.

    Hi again LuAnn_Freund,
    Try the same steps that eunicerocksify suggested, but try these DNS settings;
    Primary DNS Server = 209.244.0.3
    Secondary DNS Server = 209.244.0.4
    If those do not work, I would suggest speaking with HP's Cloud Support Team to get this issue looked at first hand by an agent that can log onto your computer. I understand that you are posting on the Forums for a reason, but since you only have today remaining to work on a resolution, speaking with them would be best.
    Please call HP’s Cloud Services at 855-785-2777. If you live outside the US/Canada Region, please click the link below to get the support number for your region, click HERE to find the Technical Support number for your country/region.
    Cheers,
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • Unable to enable in web services using direct cable from my router

    LaserJet Pro printer is working.  Unable to enable in web tab error message: Connection error. Check Internet connection.
    I have internet connection and don't  use proxy server.  I have powered off both printer and router.  Thank you.

    Hello! Could you please provide more information regarding the issue, such as which laserjet you are using? Any additional information will be helpful in resolving your issue. Thanks!
    Help the community by marking this post as a solution if it solved your issue!.
    If my post helped you in any way, please click the blue KUDOS star under my name! It would mean a great deal.

  • How do I get to the screen on my Audigy 2ZS where I can enable 'SPDIF Pass-through'

    I see the screen on your support page but I cannot get to this screen with my software. Do I need to download a driver or application to get this option. I have a set of Logitech Z-5500 digital speakers on my Dell XPS 600 computer. I am using the digital coax cable but I need to enable SpDIF passthrough to let the speakes decode the digital output from my sound card in order to get surroun sound from the 5. speakers.

    Click on Media Source "Go", then click the "Product Settings" tab, then choose "Device Controls" and click on the "Decoder" tab.

  • Howto enable spdif output through the combo ja

    I have an Audigy model #sb0090
    I am running Vista Home Premium
    I am connecting this computer to my Dolby 5. receiver.
    Creative Vista drivers are installed and reporting no errors.
    On the back of the Audigy card there is a digital output jack labeled: "digital out or 3"
    I purchased the Digital IO Module from:
    http://us.creative.com/products/product.asp?category=&subcategory=6&product=780
    When I plug it in, I don't get audio from either the coax or the optical outputs. I have enabled spdif output in the OS. I also have a daughter board model# ct4660 (from an older sound blaster li've) that I can connect to the audigy via a ribbon cable. The ct4660 also has a coax output. When I use this, the Dolby Digital output is sent to the receiver and everything works. The problem is, I don't have room in the case for the ct4660 which takes up an extra pci slot. How do I tell the card to send digital out to the "digital out or 3" output on the Audigy?
    Thanks for the help...

    I went out and purchased a new Audigy SE. Using the IO module, I now am able to get Dolby Digital sound from digital sources such as DVDs and ATSC television. I do not get any other sound such as Windows sounds and music. In the Audigy speaker properties on Vista, the "Digital Output Only" checkbox is not checked. How do I get all sound to output via the spdif output?

  • MB BIOS 2.2TB MBR limitation: Can add-on drive controller BIOS enable UEFI/GPS on a non-bootable data drive?

    I am working on older hardware that is not UEFI enabled so it is subject to the 2.2TB volume limitation under Windows Server 2012 R2 resulting in 11.6TB of unusable drive space. I installed an Adaptec Series 7 2274500-R 71605E controller card and created
    a striped RAID 10 totalling 13.6 TB of drive space. During boot, the Adaptec BIOS is installed on the system, which prompts the following question:
    Since the boot utilizes the motherboard BIOS, clearly the boot partition cannot exceed the 2.2TB limit. But what about a separate logical data drive? If I shrink the boot partition to 1TB, create a second volume at RAID level of 12.6TB formatted with GPT
    NTFS, would the Adaptec BIOS enable UEFI/GPT (since the MB BIOS would not boot to the second logical drive) and Windows Server see the full 12.6TB second drive volume?
    Yes, I am aware that I can create multiple 2.2TB partitions, but that would be an inefficient option for this installation.
    Any thoughts or suggestions will be greatly appreciated.
    Thanks!

    Hi,
    According to your description, my understanding is that you want to use add-on drive controller to enable UEFI/GPS on a non-bootable drive.
    In order for an operating system to fully support storage devices that have capacities that exceed 2 TB, the device must be initialized by using the GUID partition table (GPT) partitioning scheme. If the user intends to start the computer from one of these
    large disks, the system’s base firmware interface must use the Unified Extensible Firmware Interface (UEFI) and not BIOS. Windows support for hard disks that are larger than 2 TB, and there are some prerequisites are needed.
    Detailed information reference link:
    https://support.microsoft.com/en-us/kb/2581408
    Best Regards,
    Eve Wang
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Admin applet issue (unable to enable java plugins)

    i installed orlc UCM on linux 64 and the (unable to enable java plugins) so i cant access admin applet..
    i did this
    http://www.java.com/en/download/help/linux_x64_install.xml
    http://www.oracle.com/technetwork/java/javase/manual-plugin-install-linux-136395.html
    but still nothing,,
    Edited by: mahmoud abukhaled on Sep 17, 2012 2:06 AM
    Edited by: mahmoud abukhaled on Sep 17, 2012 2:08 AM
    Edited by: mahmoud abukhaled on Sep 17, 2012 2:16 AM
    Edited by: mahmoud abukhaled on Sep 17, 2012 2:16 AM

    You need to add security policy file
    Check this out
    http://stackoverflow.com/questions/2612895/where-to-place-java-applet-policy-file
    http://geosim.cs.vt.edu/Java/MigModel/help/Policies.html
    Regards,
    Vikrant Korde

  • A cd in itunes & unable to burn..why? answer none of file can be burned to a cd..

    loadeded a cd in itunes & unable to burn.  error message says none of file can be burned.

    Tell us more about your computer and software.  All we see is it is an iMac which could be over 12 years old and running software that is 10 system versions out of date.
    Have you tried a premium brand of CDs?  Slower burn speed?

  • SQL*Loader-266: Unable to locate character set handle for None

    Hi All,
    I am getting "SQL*Loader-266: Unable to locate character set handle for None" through sql loader.
    NLS Parameters are :
    NLS_LANGUAGE AMERICAN
    NLS_TERRITORY AMERICA
    NLS_CURRENCY $
    NLS_ISO_CURRENCY AMERICA
    NLS_NUMERIC_CHARACTERS .,
    NLS_CALENDAR GREGORIAN
    NLS_DATE_FORMAT DD-MON-RR
    NLS_DATE_LANGUAGE AMERICAN
    NLS_CHARACTERSET AL32UTF8
    NLS_SORT BINARY
    NLS_TIME_FORMAT HH.MI.SSXFF AM
    NLS_TIMESTAMP_FORMAT DD-MON-RR HH.MI.SSXFF AM
    NLS_TIME_TZ_FORMAT HH.MI.SSXFF AM TZR
    NLS_TIMESTAMP_TZ_FORMAT DD-MON-RR HH.MI.SSXFF AM TZR
    NLS_DUAL_CURRENCY $
    NLS_NCHAR_CHARACTERSET UTF8
    NLS_COMP BINARY
    NLS_LENGTH_SEMANTICS BYTE
    NLS_NCHAR_CONV_EXCP FALSE
    Kindly help
    Thanks in advance

    Please, provide the exact value of the NLS_LANG environment variable, if defined in the shell environment of SQL*Loader, and the NLS_LANG Registry setting, if on Windows. Please, provide the SQL*Loader control file.
    -- Sergiusz

  • Unable to Enable Maintenance Mode

    This is my new challenge. I am unable to enable the maintenance mode. Following is the error message taken from adadmin.log. At the same time when I issue the command to enable it, there is core dump in the alert log and this is what it says. Please help me troubleshoot this issue.
    Errors in file /oraadmin/SID/udump/SID_ora_7943.trc:
    ORA-07445: exception encountered: core dump [kopxccc()+92] [SIGSEGV] [Address not mapped to object] [0x000000062] [] []
    Change Maintenance Mode
    Maintenance Mode is currently: [Disabled].
    Maintenance mode should normally be enabled when patching
    Oracle Applications and disabled when users are logged on
    to the system. See the Oracle Applications Maintenance
    Utilities manual for more information about maintenance mode.
    Please select an option:
    1. Enable Maintenance Mode
    Please select an option:
    1. Enable Maintenance Mode
    2. Disable Maintenance Mode
    3. Return to Main Menu
    Enter your choice [3] : 1
    sqlplus -s &un_apps/***** @/apps/tcfsmgr2/tcfscdi1appl/ad/11.5.0/patch/115/sql/adsetmmd.sql ENABLE
    declare
    ERROR at line 1:
    ORA-03113: end-of-file on communication channel
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    ERROR:
    ORA-01041: internal error. hostdef extension doesn't exist
    memory exhausted
    ORA-24323: value not allowed
    Error accessing package DBMS_APPLICATION_INFO
    ERROR:
    ORA-03114: not connected to ORACLE
    memory exhausted
    memory exhausted
    An error occurred while running adsetmmd.sql.
    Continue as if it were successful [No] : No
    aiimToggleMaintenanceMode():Error while calling aiucm3().
    AD Administration error:
    Unable to Enable Maintenance Mode.

    Yes, I was able to enable it from the backend;
    SQL> @/apps/tcfsmgr2/tcfscdi1appl/ad/11.5.0/patch/115/sql/adsetmmd.sql ENABLE
    PL/SQL procedure successfully completed.
    Commit complete.
    I am quite sure it did not work when it tried last night.
    Let me try to do it using adadmin again. May be issue is no longer an issue.

  • Unable to enable DirectX effects (hangs at 92%!)

    When I try to enable DirectX effects, Audition first refreshes the effects list. It does this fine until it gets to 92%, then it hangs, stopping at the same effect (JetAudio Sound Effector V3) each time. Audition is still running but nothing happens, it just doesn't go any further, and I have to force close the program.
    Can anyone think of a way I can stop this one effect from loading? I searched but couldn't find any file with that file name.
    I am unable to enable any of my DirectX effects. Thanks for any help.

    Dodgy DirectX has always been a bit of a problem. Unlike VSTs, which are essentially DLLs that sit somewhere nice and sensible, and you can install and delete them easily, DirectX has to use an installer, and heaven only knows where it puts the appropriate files... although I understand that the real issue with removing them is that they end up as registry entries, and not necessarily straightforward ones either.
    Probably the most useful thing I can suggest is that you look at this thread on the KVR forum, where there are a couple of suggestions.

Maybe you are looking for

  • Using variables in the Select statement

    Here is my Select statement: Set EmpDynaset = OraDatabase.CreateDynaset("select CU_NAME,CU_CONTACT from CU where CU_Name =" & cnt, 0&) What's wrong with this? I'm trying to use the variable cnt. Any help? Thanks, Jeremy

  • Overlaying Photo image on multi-colour background

    Hello, I hope someone can point me in the right direction with this one - as I'm a bit stuck. I am creating a graphic for use as a background image on a webpage that uses three colours. I want to add a picture in the top right of the page. I have rem

  • PSE9/Win 7: Edit/Copy does a Cut?

    I'm running PSE 9 on Windows 7. I must have forgotten how to do a copy/paste. Here is what I did: m - to select a rectangular area Edit/Copy - to make a copy of the contents of the Selection Click on the Move Tool. When I start to move my selection I

  • Please, example for Grouped bar chart

    I need to creat grouped bar charts in an Applet. Could you please forward instruction? Thanks.

  • ITunes Connect java.lang.NullPointerException

    I have been dealing with an issue in the iTunes Connect Resolution Center.  Submitting messages to them through that tool has been working during the outage until I attempted to submit a response today.  I am now getting a 'java.lang.NullPointerExcep