Unable to establish OSPFv3 neighbors through transparent ASA

I have 2 devices running IPv6 with an ASA ver 8.4(2) in transparent mode with multiple contexts in between them.  I can ipv6 ping the devices through the ASA but can not get the 2 devices to establish OSPFv3 adjacency.  They are able to establish adjacency with ipv4 OSPF.  When running debug ipv6 ospf hello I see each of the devices sending hellos but not receiving them from the device on the other side of the ASA. I notice that the hellos are coming from the link local addresses and not the unique global addresses that I applied to the interfaces. If I connect a device directly to one of the devices I can establish OSPFv3 adjacency without a problem.
Any thoughts?
Bob

Bob,
It is expected that OSPF/EIGRP etc use link local rather than unique global ;-)
Regarding the problem.
- please enable
logging buffered infologging buffer-size 1000000
- and ASP drop capure.
cap ASP type asp all
Try establishing the adjacency and check
show logg sh cap ASP
I would also try establishing the adjacency without multicast (point-to-multipoint network should allow this).
Marcin

Similar Messages

  • I am able to connect to the internet using internet explorer, but when I try to connect through mozilla firefox it says 'it is unable to establish a connection to the server." why?

    I can establish internet connection through internet explorer using a router at my house, but whenever I attempt to connect using firefox, it says it is unable to connect.

    A possible cause is security software (firewall) that blocks or restricts Firefox without informing you about that, possibly after detecting changes (update) to the Firefox program.
    Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process.
    See [[Server not found]] and [[Firewalls]] and http://kb.mozillazine.org/Firewalls

  • Computer unable to establish two-way communication to J4580 through Airport Extreme

    I have my J4580 connected to an Airport Extreme base station via usb.  I've installed the printer software on my HP laptop (Vista) and Bonjour recognizes the printer as networked & installed, but when I try to print, i receive an error message "Computer is unable to establish two-way communication with the device" and the printer queue shows an error.  I've attempted to find a solution through the posts, but haven't seen much that seems to apply to J4580.  Any help???  Thanks!

    I came across this similar problem and spent days trying to figure it out. I knew I was close when I tried to start the HPZ12
    service and it kept failing with "unable to find the specified file". I traced it with a process monitor and found that it was looking
    for a registry key that was not present. Specifically:
    HKLM\System\CurrentCosntrolSet\Services\Pml Driver HPZ12\Parameters
    It was looking for the string:
    ServiceDLL which should be set to:
    C:\WINDOWS\system32\HPZipm12.dll (or something similar)
    The unfortunate thing is that no matter how many times you install and uninstall the HP drivers, then don't reset the registry keys
    for the HPZ12 service. In the end, I ended up doing the following:
    1. Uninstall software and reboot
    2. Go through registry editor and delete the PML key (just did a search for all PML occurences)
    3. Deleted the c:\program files\Hewlett-Packard directory
    4. Deleted the c:\program files\HP directory
    5. Deleted the c:\windows\system32\spool\drivers\w32x86\ contents (anything that referred to an HP printer or driver)
    6. Deleted the HKLM\Software\Hewlett-Packard registry key
    7. Rebooted
    8. Reinstalled and everything worked.
    I suggest you backup any registry keys prior to deleting them in case you make a mistake. You can use the Export feature on
    the right-click context menu to save each key you delete, or use some tool to make a backup of your registry prior to making
    these changes. Similarly, for the files, I renamed directories or created backups of their contents.
    Once I reinstalled, I found that there were TONS of new registry keys added that weren't there before. So the real problem is
    with HPs install/uninstall. It doesn't clean up properly and any aborted or failed instalation will leave the drivers in a poor state.

  • The computer is unable to establish a two way communication with the device

    Hi  I am trying to fix a problem for some one else, and I am struggling where to look next. The issue is that we are unable to check the ink levels of a HP Deskjet 1050 printer.  The error message states that the computer is unable to establish a two way communication with the device. After running through the troubleshooting guide about this issue on the HP site with no joy,  I decided that it may be the printer and suggested a replacememnt.  Unfortunately A new HP Envy 5530 was purchased and connected (wirelessly) but the issue remains. I have uninstalled the drivers multiple times, and also disabled any firewall/anti virus software in case this was interfering. I was hoping that some one could point me in the right direction next? None of the other forum posts here (or any google searches) give a solutuon which has fixed the problem.  Thanks

    No I cant. Unable to ping the printer too, not sure if this is possible normally?

  • The computer is unable to establish 2 way communicat​ion with the device (Officejet 8500)

    My printer is printing with lines running through it and sometimes in yellow (even though I'm only printing in black & white) I was going to try to use the troubleshooter but it's unable to establish 2-way communitcation... Can you let me know how to establish this communication or do you have any ideas why my printer is acting up this way?
    Thanks so much for taking the time today to be on this forum!

    Hi, try aligning the printer. Follow the instructions provided in this link to align the printer.
    http://h20564.www2.hp.com/hpsc/doc/public/display?​docId=c01615965
    You might need to reinstall the printer software to establish 2-way communication. You can download the latest software from this link.
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloa​dIndex?softwareitem=mp-110033-1&cc=us&dlc=en&lc=en​...
    If my answer was helpful please click on the "Thumbs up" button on the left to say "Thanks".
    Click "Accept as Solution" if it solved your problem, so others can find it.
    Although I am an HP employee, I am speaking for myself and not for HP.

  • Error -  unable to establish JCO connection with SSO

    Hello,
    I have implemented XSS on WebDP and this is working fine. So my JCO connections SAP_R3_HumanResources must be configured correctly. However I have just done the 'GetFlight' BAPI tutorial and upon execution I get the error:
    'com.sap.tc.webdynpro.modelimpl.dynamicrfc.WDDynamicRFCException: Could not create JCOClientConnection for logical System: SAP_R3_HumanResources - Model: class com.sap.tut.wd.flightlist.model.FlightModel. Please assure that you have configured the RFC connections and/or logical system name properly for this model!'
    CAUSED BY
    'User not authenticated (is anonymous) - unable to establish JCO connection with SSO'
    Can anyone help here?
    Thanks
    Mr.T

    HI
    GOOD
    GO THROUGH THIS LINK WHICH CONTAINS THE A SINGLE SIGN-ON IN A COMPLEX SYSTEM LANDSCAPE.
    https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/80fbc690-0201-0010-1aba-93d5c8232b4a
    http://www.sap-press.de/download/dateien/1020/sappress_sap_security_authorizations.pdf
    http://sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/ff65b5a2-0a01-0010-5b97-e747192a1d49
    THANKS
    MRUTYUN

  • Client unable to establish connection; 08001;

    Hello,
    My SSAS multidimensional cube processing fails with the following error:
    "OLE DB error: OLE DB or ODBC error: A network-related or instance-specific error has occurred while establishing a connection to SQL Server. Server is not found or not accessible. Check if instance name is correct and if SQL Server is configured to
    allow remote connections. For more information see SQL Server Books Online.; 08001; Client unable to establish connection; 08001; Encryption not supported on the client.; 08001"
    It was running fine with no errors till yesterday. Does anyone know what may be wrong?
    Could it be because of a new firewall rule on the server that host the SQL server?
    Appreciate your help!
    Thanks!

    Hi Nihcas,
    Based on the error message, it seems that the account cannot connect to the data source of the SQL Server Analysis Services database. And you said that a new firewall rule on the server that host the SQL server, then this issue can be caused by this firewall.
    To access an instance of the SQL Server through a firewall, you must configure the firewall on the computer that is running SQL Server to allow access. The firewall is a component of Microsoft Windows. In your scenario, please try to configure the Windows
    Firewall to Allow SQL Server Access and check if the issue is persists or not.
    http://msdn.microsoft.com/en-us/library/cc646023(v=sql.105).aspx
    Regards,
    Charlie Liao
    TechNet Community Support

  • "Unable to establish a connection between WebEx and the mail server."

    Hi,
    I installed Cisco WebEx and integrated with our Microsoft exchange server.  It showed server "UP".  everything's came up and working fine after that and sudenlly i found this message "Unable to establish a connection with the mail server.  Please recheck settings."
    I went into the Mail Server setup to edit settings and now, it shows Server Down.  Do I need to do something on the MS Exchange 2010 or from webex server ??
    Any help is greatly appreciated.  Thanks a lot!

    Every 180 seconds, CWMS verifies the connection to the SMTP server by establishing a connection on TCP port 25 (SMTP) and then sending the EHLO command followed by the QUIT command. This check is also performed once when logging into the admin web page or when browsing to System -> Servers (where the status of the mail server is displayed).
    If  this sequence does not complete successfully, the warning “Unable to  establish a connection with the mail server. Please recheck settings.”  will show in a banner at the top of the CWMS admin pages.
    You  can verify the connection to the SMTP server manually by using “telnet  25”.
    If you have access to the CWMS unix shell be aware that CWMS does not come  with the telnet command installed.
    As an alternative, you can use this 3-lines script:
    exec 3<>/dev/tcp/x.x.x.x/25
    echo -e "EHLO\r\nQUIT\r\n " >&3
    cat <&3
    Replace x.x.x.x by the ip address or hostname of the SMTP server and save the script in a file, f.e.:
    /* script saved in a file named ehlo */
    [root@dchriste-cwms-adm1 ~]# cat ./ehlo
    exec 3<>/dev/tcp/10.48.54.79/25
    echo -e "EHLO\r\nQUIT\r\n " >&3
    cat <&3
    Then, execute it:
    [root@dchriste-cwms-adm1 ~]# sh ./ehlo
    The output should be similar to this:
    220 *******************************************************************************************************************
    250-confukdc.confuk.com Hello [10.48.52.110]
    250-TURN
    250-SIZE
    250-ETRN
    250-PIPELINING
    250-DSN
    250-ENHANCEDSTATUSCODES
    250-8bitmime
    250-BINARYMIME
    250-CHUNKING
    250-VRFY
    250-XXXXXXXXXXXXXXXXXXXXXXXA
    250-X-EXPS=LOGIN
    250-AUTH GSSAPI NTLM LOGIN
    250-AUTH=LOGIN
    250-X-LINK2STATE
    250-XEXCH50
    250 OK221 2.0.0 confukdc.confuk.com Service closing transmission channel
    Also, you can use this tcpdump command to see the conversation (replace x.x.x.x by the SMTP server’s IP address or hostname):
    tcpdump -vXs 0 host x.x.x.x and tcp port 25
    If you have HA, it is not certain which admin VM talks to the smtp server, so best to check both.
    If you don't have access to the CWMS unix shell, best to span the switch ports and run packet capture.

  • Error while connecting oracle11g to sql server through transparent gateway

    Hello
    i'm facing this errors when i try to connect oracle 11g to sql server through transparent gateway:
    http://www.freeimagehosting.net/newuploads/d4454.jpg
    the directory for my db is : C:\oracle\product\11.1.0\db1
    and for the gateway: C:\oracle\product\11.1.0\dg4msql
    the configurations i used:
    gateway :
    tnsnames.ora:
    dg4msql =
    (DESCRIPTION=
    (ADDRESS=(PROTOCOL=tcp)(HOST=Kinda-PC)(PORT=1522))
    (CONNECT_DATA=(SID=dg4msql))
    (HS=OK)
    listener.ora:
    GATELIST =
    (DESCRIPTION_LIST =
    (DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = Kinda-PC)(PORT = 1522))
    (DESCRIPTION =
    (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1522))
    SID_LIST_LISTENER =
    (SID_LIST =
    (SID_DESC =
    (PROGRAM = dg4msql)
    (SID_NAME = dg4msql)
    (ORACLE_HOME = C:\oracle\product\11.1.0\dg4msql)
    and for the oracle database :
    listener.ora
    LISTENER =
    (DESCRIPTION_LIST =
    (DESCRIPTION =
    (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521))
    (ADDRESS = (PROTOCOL = TCP)(HOST = Kinda-PC)(PORT = 1521))
    tnsnames.ora:
    DB1 =
    (DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = Kinda-PC)(PORT = 1521))
    (CONNECT_DATA =
    (SERVER = DEDICATED)
    (SERVICE_NAME = db1)
    gateway =
    (DESCRIPTION=
    (ADDRESS=(PROTOCOL=tcp)(HOST=Kinda-PC)(PORT=1522))
    (CONNECT_DATA=(SID=dg4msql)
    (HS=OK)
    thanks :)
    Edited by: 903043 on Dec 18, 2011 6:18 AM

    Did you go through the various steps in the doc?
    There is a gateway specific forum below;
    Heterogeneous Connectivity
    Cheers
    David

  • I can no longer access facebook from my macair and when i try the following error message appears "unable to establish a secure connection to the server.

    I have had no issue accessing Facebook in the past using my MacAir.  Last night each time I would try and access the page, an error message would appear, saying that unable to establish a secure connection to the server "www.facebook.com"".  The problem continues this morning.  I have not updated any software or made any changes.  One minute it was working, the next it was not.  I do not have any parental controls; I have deleted the cookies; and I have reset safari.  I can access all other websites that I have tried.  I am using Version 6.0.4.

    From your Safari menu bar click Safari > Preferences then select the Privacy tab.
    Click:  Remove All Website Data
    Then delete the cache.
    Now open a Finder window. From the Finder menu bar click Go > Go to Folder
    Type or copy paste the following
    ~/Library/Caches/com.apple.Safari/Cache.db
    Click Go then move the Cache.db file to the Trash.
    Quit and relaunch Safari to test.
    If nothing above helped, troubleshoot Safari extensions.
    From the Safari menu bar click Safari > Preferences then select the Extensions tab. Turn that OFF, quit and relaunch Safari to test.
    If that helped, turn one extension on then quit and relaunch Safari to test until you find the incompatible extension then click uninstall.
    If it's not an extensions issue, restart your internet modem and router.  Then quit and relaunch Safari and try Facebook.

  • I just upgraded to mountain lion. I am unable to use airplay mirroring through my apple tv. They are both on the same network. It says a airplay icon should appear in the menu bar but it isn't there. What am I missing here?

    I just upgraded to mountain lion. I am unable to use airplay mirroring through my apple tv. They are both on the same network. It says a airplay icon should appear in the menu bar but it isn't there. What am I missing here?

    http://www.apple.com/osx/specs/

  • Unable to establish connection to R/3

    Hi,
    We have just installed XI and done all configurations.
    I am doing one example ( connection r/3 to legacy system ) . When I open I outbound object in Integration Repository and in Imported objects when right click on IDocs and click Import SAP Objects, it asks me for SAP logon details , but when I try to connect it shows an error
    Unable to establish connection to R/3 system 133.136.233.170 (system=00, client=110) Troubleshooting tips:
    Is the target system online?
    Check the connection data (note that server names and groups are case-sensitive)
    Tips for administrators (see the configuration guide for more details):
    Does the user have the required authorizations in the target system?
    Is the target system configured correctly in "etc/services"?
    I am putting IP address in application server and checked the system number as well.
    I am able to ping From webas to R/3.
    can anybody help me out what could be the error
    Thanks
    Rekha

    Hi Rekha,
    did you take a look at this page?:
    http://help.sap.com/saphelp_nw04/helpdata/en/2b/a48f3c685bc358e10000000a11405a/content.htm
    you can find sap notes - if you're expiriencing problems with idoc import (SAP Notes 677732 (authorizations), 672745 (missing function modules), 212011 (access to IDoc metadata), and 718320)
    also "Authorizations Required to Import from Systems Based On SAP Web Application Server"
    take a look at this page
    and read if carefully it may help you with your problem:)
    Regards,
    michal

  • Unable to establish a session with the Address Book Server

    I have installed the following
    Sun Java System Messaging Server 7 Update 3
    Sun Java System Calendar Server 6.3
    Sun Java System Directory Server 6.3.1
    GlassFish Enterprise Server 2.1 Patch 2 with HADB support
    Delegated Administrator 7
    Sun Convergence 1 Update 3
    as per the instruction here
    http://wikis.sun.com/display/CommSuite7/Sun+Java+Communications+Suite+7+on+a+Single+Host
    My problem is that when I open outlook and try to add a new contact, I get a message saying:
    Unable to establish a session with the Address Book Server. Contact your server administrator for help or try later.
    When using webmail, I can add contacts just fine.
    How can I fix this problem?
    Thanks
    Edited by: Nevron on 26 ??? 2010 11:31 ??

    Nevron wrote:
    My problem is that when I open outlook and try to add a new contact, I get a message saying:
    Unable to establish a session with the Address Book Server. Contact your server administrator for help or try later.Refer here:
    http://forums.sun.com/thread.jspa?threadID=5424727
    You need to log a Sun support request to get the latest Convergence patch.
    Regards,
    Shane.

  • VMware SQL 2008R2 bcp error - SQLState = 08001, NativeError = 0 Error = [Microsoft][SQL Server Client 10.0] Client unable to establish connection due to prelogin failure

    Can someone help me resolve this error?   Thanks  
    Windows Server 2008 R2  Standard SP1 64-bit -  SQL Server 2008R2 Standard 64-bit 
    VMware vCenter Server Version 5.1.0
    SQLState = 08001, NativeError = 0
    Error = [Microsoft][SQL Server Native Client 10.0]Client unable to establish connection due to prelogin failure
    bcp program: 
    bcp SYM.dbo.ACCOUNT in "D:\Data\SQLExtract\EXTRACT.ACCOUNT" -f"D:\Data\SQLCommands\FMT.ACCOUNT" -S DEV-DATA\TEST\ -T -oSYMLOAD.LOG Type SYMLOAD.LOG >> SYMLOAD.LOG.CUMULATIVE
    The bcp program executes successfully on a local instance of SQL Server.

    The error has nothing to do with BCP as such, but it is a connection problem. That is, for some reason you cannot connect to your instance from the VM. I would exect that you face a similar problem if you tried SSMS.
    It could be a firewall issue, but prelogin suggests that you reach the instance. But possibly you don't come far enough for the login failure to be recorded. Possibly the instance is not configured to audit login failures.
    The message you would see would be similar to
    2010-08-18 14:11:30.91 Logon       Error: 17809, Severity: 20, State: 3
    Possibly followed by a a line that details the message. The error number may be different.
    Erland Sommarskog, SQL Server MVP, [email protected]

  • Unable to establish a for loop in custom rtf template for seeded xml file

    Hi Experts ,
    I am Unable to establish a for loop in custom rtf template for seeded xml file. i am using <?:for-each:G_BSALINE?> FORM FIELD .....<?:FOR-EACH?END> .AM i missing something?
    Please help.
    Thanks

    Hi,
    Need more information about your XML data structure; however based on the code you provided, the synax does not look right; you have some colon sign where it is not needed etc... You could use the following (although not quite sure if you want to use Form Filed to group by or just display), but look at the example provided below.
    <?for-each-group:G_BSALINE?> FORM FIELD .....<?end for-each-group?>
    Example code:
    <?for-each-group:G_INVOICE_NUM;./INV_TYPE?>
    xxxxxxxxxx
    <?end for-each-group?>
    Thanks!

Maybe you are looking for