Unable to find ctrl+H message in UCS C220 Server

Hi,
I am unable find Ctrl +H message at the time of booting to get enter in Webbios.
Please help me.
Hardware: UCS RAID SAS 2008M-8i
Rgds,
Sambhab

What firmware are you running on this server?
Did you buy this raid controller direclty from cisco or from a partner.
Based on the screenshot you provided the firmware on your controller looks very old, I recommend that you use the HUU to upgrade the firmware of the adapter to the same level as your server. Use link below to download the firmware package for your server.
Cisco UCS C220 M3 Rack Server Software
http://software.cisco.com/download/release.html?mdfid=284296253&flowid=31742&softwareid=283850974&release=1.5%283d%29&relind=AVAILABLE&rellifecycle=&reltype=latest
Example Video of firmware upgrade.
http://www.youtube.com/watch?v=qRahHRja15M

Similar Messages

UCS C220 server power button turns "Amber"

Hi All,
We have a UCS C220 server on which we are running CUCM 9.1 and CUC 9.1 and all of a sudden the server's power button turns amber and everything goes down. We would have to physically turn on the power button and access the VMware and start all the services.
Please advise.
Regards
Bhavna

Hi, I have the same issue, I just install a new clean CUCM 9.1 and CUC 9.1 in UCS C220 with pre-installed esxi 5.1, I leave the clients site the last Friday and today say to me that the servers is down, just turn on the server and everything comes back, in the vmware logs the only error that show is "2014-05-18T15:31:00.802Z [3DAE2B90 error 'SoapAdapter.HTTPService'] HTTP Transaction failed on stream TCP(error:Transport endpoint is not connected) with error N7Vmacore15SystemExceptionE(Connection reset by peer)" but I saw that error in the log before I installed this site the last May 5, anyone have a clue of what I have to look. Of if this error could do a crash or reset in the system.
Thanks in advance.
Cesar

How to disable a CPU on a UCS C220 server

Hello Experts ,
Would anybody help if there is a way to disaable a CPU on a UCS C220 server ?
Is there a jumper that is used for this purpose ?!!
ASAP
Thanks guys

Short of removing the physical CPU I don't believe there's any other way to "disable" it. Removing the CPU will also render it's memory banks (usualyl 1/2 the DIMMs) inaccessible to the system.
What reason to have for requiring to disable it?
Regards,
Robert

Unable to find the sms messaging api

I've downloaded the sun wireless toolkit 2.3 but when the complier hits the line
import javax.wireless.messaging.*;
I get an error message:
package javax.wireless.messaging does not exist
has anyone seen this before? can someone suggest how to fix this problem?

You may check this tip to solve your problem:
Unable to find a package while compiling a program in the Sun Wireless Toolkit
http://www.java-tips.org/content/view/151/39/

Jdeveloper remote debugging - Unable to find source error message

Hi,
I am trying to remote debug a simple Java application (non-web) using Jdeveloper. The Jdev debugger can connect to the remote debuggee, but unfortunately it throws me a message saying: 'Unable to find source file'. As a result, if I ignore this message, it simply ignores my source breakpoints.
Can anybody please help with any tips?
My project source is checked out from CVS and does not follow a conventional source path as such.
Thanks,
Neil.

The warranty entitles you to complimentary phone support for the first 90 days of ownership.

Mail is unable to find response to messages

When selecting the backward arrow icon in the mail column view I get an error message reading 'Mail was unable to find your response to the message “message title”. You may have deleted the message.'
This occurs frequently, even right after sending an e-mail. I am confused as I did not delete the copy of the outgoing message and it is still found in the "sent" message mailbox.
This did not occur in my old Powerbook but has started in my new MacBook Pro. I have everything set up the same as my Powerbook so, again I am confused. The email accounts are POP (not imap), if that makes a difference.
Any info would be helpful. Thanks!

This is a problem that has been reported here quite a few times and for which no solution has been found yet. Doing some cache-cleaning, or even just restarting the computer, fixed the problem in some cases.
Read the following article for general troubleshooting and cache-cleaning procedures:
Resolving Disk, Permission, and Cache Corruption
Be sure to read this as well:
Side effects of System cache cleaning
In addition to the utilities mentioned there for cache cleaning, you may also consider OnyX or Cache Out X, which are free.

Mail was unable to find reply to message

Hi Guys
Im using OS X Yosemite (10.10.1) and use Mail with Exchange for emails. Just recently when I click on the grey return arrow to view the reply ton an email I have sent, it get the following error message:
'Mail was unable to find reply to your message. You may have deleted the message.'
The message has not been deleted as I can see it by going to my Sent folder. It has also worked in the past.
Our whole office (10 people) are all set up EXACTLY the same with Mail/Exchange and are all using Yosemite. Some of us have the same issue as me, and others work perfectly.
Does anyone else have this issue or a solution?
Cheers
Sara

Hi,
I have the same problem but try this. On my mac is works but only with old messages not new replied.
go to Library->Mail->V2->MailData and look for files started with word "envelope". Put this file to trash logout and log in and start mail Wait for reindex...on my mac it works with all replied arrows but problem is when I reply to new message and then click on arrow I have the same error about potentially deleted message.

Unable to find the xml message in the queue even though xml is invoked

Hi,
Currently,we are invoking a queue in a BPEL Process where we are trying to place an xml into it.When verified in Console can see the queue is invoked and also a new record is being created in the queue but unable to find that xml in it.Could you please tell me how and where can we find the xml in the queue.
Regards,
N.Das
Edited by: DasN on 05-Mar-2013 22:52

Check these...
https://forums.oracle.com/forums/ann.jspa?annID=893
http://docs.oracle.com/cd/E13222_01/wls/docs100/ConsoleHelp/taskhelp/jms_modules/queues/ManageQueues.html
Cheers,
Vlad

Unable to find messgaes in Message monitoring.

Dear All,
When trying to search messgaes in Message Monitoring using - Adapter Engine, I am able to find only todays messages and not previous days messages. Previously I am able to find past data using Free entry. But this problem is occuring from last 2 weeks.
Could you please suggest the possible ways to solve this issue...
Thanks & Regards,
Hari.

Hi,
this can be due to two things...
either no interfaces have been processed during that time or archiving jobs have been enabled for 1 day....
check in Moni if there are any archive jobs scheduled ..go to sxmb_adm and select define interfaces for archiving and deletion..and check the days specified over there also..addition to adapter engine archive jobs...
HTH
Rajesh

Long beep sound in UCS C220 Server

Hello All,
We have recently upgraded our CM server from MCS to UCS C220. All is working well since 3 weeks. However, since the past three days the UCS server is giving long beep sounds. In the CIMC console its showing as Severe Fault and in Storage Slot 1 and physical Drive 2, the status is "Foreign Configuration" and Health status is "Moderate Fault". However, when we check the status of the light on the physical drive, its still green and not amber. So is it there a problem with the Harddrive?
Pls find the screenshot attached.

Hey there. I don't think you'll get a reply on this forum because it looks like this is a fault on the UCS server itself, and not on the Unified Communication application that runs on the UCS server. Please re-post this discussion to the board which discusses UCS servers. You'll get a reply there.

Unable to find the sended message from create support message in solman.

Hello everybody,
I had installed the Solution manager and IDES server.
I have configure the Maintenance Optimizer, Now I am able to send the
support message from the IDES.
But Now where to find or serach the message in solution manager ?
or need to be configure service desk?
Please suggest me step by step configuration to check the sended message.
Thanks

hi
>
ganesh borase wrote:
> I have configure the Maintenance Optimizer, Now I am able to send the
> support message from the IDES.
> Thanks
sorry nt clear from your above statement, you configured maintenance optimzer for download supprot packages. do you want to configure support messages functiionality?
Can you please clarify your requirement?
Thanks,
Jansi

Unable to find the customer message.

Hi Gurus,
I m facing a problem where I can create the customer message through steps.
Help-->Create Support Message and then enter the message in the same.I had configured the Service Desk Management System in the ECC6 System.I can view the calls or the messages in the Solution Manager (locally).But I had configured the Q.A. System for generating the customer message.When I create the message it shows as message created successfully but I cant view the message list in Solution Manager.
Request you please guide me for the solution .
Eagerly waiting for the positive response.
Regards,
Amit

Hi Milind,
you can only change a message if the message is at status 'customer action', but if I understand you corretly you have sended the message to SAP and you want to change now something.
This is possible but you cannot do it by your own. For doing this please call the customer center of SAP, the colleagues at the hotline their can make the change and assist you by finding the message. Which number you have to dial is listed in SAP service marketplace
service.sap.com
-> choose SAP Support Center Addresses
or check SAP note 16481.
Hope this help.
Regards,
Sabine

Unable to find the processed message

Hi
I am testing my vendor master upload for file to idoc scenario, I am keeping the file in FTP server and made processing mode as delete , the adpater is deleting the file but i am unable to the processed message in TC SXMB_MONI . any clues????????
Regards
Swatantra

Hi,
1. Check Adapter Monitoring as Divija said
2. Check in MDT and see what is the problem?
http://<host>:<port>/mdt
Message flow is like Adapter Monitoring>MDT>SXMB_MONI
Thanks,
Prakash

Unable to find base station

I just got a Mac Pro and Airport Extreme 802.11n Base Station. I was able to set up the AEBS using the Mac Pro (running Leopard), and am able to connect to it using the Mac Pro without any problems. I also updated the firmware on the AEBS. Unfortunately, I am unable to connect to the AEBS using my laptops. I have a Macbook Pro and a Titanium Powerbook, both running 10.4.11. When I try to connect to the AEBS using Airport Utility 5.2.1 with either laptop, I get an "unable to find base station" message. Both laptops are in the same room as the Mac Pro (about 30' from the AEBS, which is in another room), and both are fitted with the original Apple Airport cards. I realize that I could install Leopard on the laptops to see if that did the trick, but I'd rather not go to all the trouble if I can help it. Any suggestions as to what may be wrong with the laptop setups that's interfering with my Airport reception? Thanks.

Is the Mac Pro connected wirelessly or via a cable? I am guessing it is wired since you have to pay extra for the wireless.
In your configuration make sure you have not enabled "Create a closed network". This turns off the SSID and will not allow it to be found by the laptops. And of course make sure you have not set Wireless Mode to OFF.
Beyond that to test for interference you can change the radio mode to 802.11n (802.11a Compatible) and see if the Macbook Pro will work. This will force the Airport to use the 5GHz radio which removes most interference.
Hope this helps

Help....Unable to find driver for this platform

Hello...after i shut down my macbook after it froze while playing counter strike when i turn it on it get this msg...Unable to find driver for this platform: ACPI....I cant boot it in safe mode...when i put my disc in and repair it doesnt help...When i follow the online text commands and start it up in single user i cant type anything...I dont wana lose all my files...I wasnt running windows on it...I was using the app thats like wine for mac...Thanks...

I just got my new MBP today and it worked for about
an hour. Now a get a panic:unable to find driver ACPI
message. Then: debugger called. Kernel version...
Restart computer.
What the? I've tried restarting, holding down the
opt/cntl/r/p keys, holding down x key, c key, etc.
Just keeps giving me same mesg, no cursor and no
comp. access. Any ideas?
thats what im going through....

Unable to find ctrl+H message in UCS C220 Server

Similar Messages

Maybe you are looking for