Unable to get access to 'rights' of a volume

I lost the ability to reset or work with the rights management of (a partition) of my secondary volume. Information in disk repair program says: no ability of rights managements. The volume is checked and found o.k. All data on the disks partition are present and work. Second partition (there are only two) on the disk is o.k. and rights management is accessible. Information by pressing "Comm./I" for that partion shows me as the owner and the admin group with the rwx permission.
How to get the rights management clean?

Is this a boot volume? If not, you can use the "Get Info" feature to ignore ownership on a volume (typically done for a data drive - check bottom left corner of get info window).

Similar Messages

Unable to get access to wism2

Hello,
I have next issue:
When i was trying to configure redundancy, i lost access to wism2 module. When i ping service port, it reply me, but i unable to get access via "session slot proc".
some brief information:
cisco WS-C6509-E
SN-1#sh module
Mod Ports Card Type                              Model              Serial No.
2    4 WiSM 2 WLAN Service Module             WS-SVC-WISM2-K9    SAL1739DEGF
5    5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G       SAL1739D9EL
SN-1#sh run | i wism
wism service-vlan 222
wism module 2 controller 1 allowed-vlan 1-1001,1006-4094
SN-1#sh wism module 2 controller 1 status
WiSM Controller 1 in Slot 2 configured with auto-lag
Operational Status of the Controller : Oper-Up
Service VLAN                         : 222
Service Port                         : 3
Service Port Mac Address             : 6c20.562c.5a61
Service IP Address                   : 192.168.1.101
Management IP Address                : 10.32.252.21
Software Version                     : 7.5.102.0
Port Channel Number                  : 547
Allowed-vlan list                    : 1-1001,1006-4094
Native VLAN ID                       : 1
WCP Keep Alive Missed                : 0
any idea?

Also, a have found a difference between second wism2 module
SN-1(config)#do sh wism module 2 cont 1 sta
WiSM Controller 1 in Slot 2 configured with auto-lag
Operational Status of the Controller : Oper-Up
Service VLAN                         : 999
Service Port                         : 3
Service Port Mac Address             : 6c20.562c.5a61
Service IP Address                   : 192.168.1.101
Management IP Address                : 10.32.252.21
Software Version                     : 7.5.102.0
Port Channel Number                  : 547
Allowed-vlan list                    : 1-1001,1006-4094
Native VLAN ID                       : 1
WCP Keep Alive Missed                : 0
SN-2#sh wism module 2 controller 1 status
WiSM Controller 1 in Slot 2 configured with auto-lag
Operational Status of the Controller : Oper-Up
Service VLAN                         : 999
Service Port                         : 3
Service Port Mac Address             : 6c20.562c.4b61
Service IP Address                   : 192.168.1.102
Management IP Address                : 10.32.252.12
Software Version                     : 7.5.102.0
Port Channel Number                  : 547
Allowed-vlan list                    : 1-1000,1006-4094
WCP Keep Alive Missed                : 0
As you can see there is no native vlan on working wism and i cant turn off it on unavailable wism.

Changed to Firefox 5.0, now unable to get access to my bookmarks, many are missing

changed to Firefox 5.0 yesterday and now need to accesss some bookmarks, but have disapeared with the Google toolbar and don't know how to get access to them. some bookmarks are there under top bookmark heading, but many are missing. how can I get back to thse that are missing please. It did say I would lose the Google toolbar, but didn't realise most bookmarks would go as well.

There is an extension to use the Google Bookmarks (included in links(
'''see''' https://support.mozilla.com/en-US/questions/841081
for alternatives, or a Google supplied
list of alternatives at the very bottom.

Unable to get access to workspace

Hi,
The group sponsor has tried to add me to this group, but we get the following error message:
"You have been invited to become a member of a Group hosted by Oracle BeehiveOnline.
The details are:
Group Name: Oracle_AC_ISV_ASFU
Group Purpose:T�ss� uusi ytritys
Group Sponsor:[email protected]
Problem - Account details are incomplete, i.e. Family Name not defined
To access the system you will have to have an Oracle corporate single sign-on account with all the necessary fields completed. In initial validation tests your account failed the test due to the family name not being entered into the Account details. Please add the necessary information to your account on OTN http://otn.oracle.com - Click on Login
Enter your username [email protected] and your password - there is a [1]Lost your Password?" link to reset if unknown. Once in the system click on the Account link on the top right. Edit your details to make sure the First Name and Last Name are completed and correct.
Save the changes and the next time the provisioning run is made you will be added to the group.
N.B. If you are an Oracle Employee you cannot change the details on this screen and should raise an iSupport Request to get the details corrected."
My SSO is working normally. I'm not able to change my details. I raised an iSupport Request and they told me to get support from this forum.
Please advise.
Br,
Jaana Viitapohja

HI, the account [email protected] has missing pieces in the wwldap record. This sometimes happens with internal staff - usually but not exclusively when they have been contractors and then go full time.
We will get the record adjusted and you should be OK then - it may take a few hours.
Phil

Unable to get account set right?

Am trying to change my email address and think I'm following directions but it keeps saying I do not have the right phone format in? It also wants an office # (I refuse to give that out) and I am also unable to insert my state? It is a complete mess. Would like some help.
Thanks

No, there can be multiple records from M2.
there can be 1 to many relation from M1 to M2.
if duplicate l_no and ma_no exists in M2, it should update the same row in m1 since combination of this column is unique

Unable to get access media recovery creator in windows 7

Hi there: i got a satellite c660-20x toshiba laptop.
os: preinstalled windows7 home basic 64bit sp1
the problem is that i cann't create media recovery dvd cuz whenever i hit this utility icon trying to open it as it used to be.(before i regretfully installed spyhunter which i have alredy uninstalled)- i got a message as follows:
"the recovery is impossible . couldn't find hdd recovery folder on the second partition of your first hard disk. there is no valid hdd recovery environment on this computer."
note that i actually have the hdd recovery folder (11.4GB) on my d drive..... also f8 key does not give any response since last week when i used it as usual choosing memory diagnostic option. so, i am no more able to get into the recovery options.i also tried to use the "system repair disc but the screen showing windows loading failed to complete the process.                               please help............ Thanks in advance.

Satellite C660-20X (PSC1LE-01W00RAR)
You can order the same recovery media from Toshiba. I would do it that way.
   Toshiba Europe Backup Media Online Shop
f8 key does not give any response ... .i also tried to use the "system repair disc but the screen showing windows loading failed to complete the process.
When the recovery media comes, it might be time to use it.
-Jerry

Site collection admin getting access denied!!

Hello All,
In my current SPFarm, All users were accessing the environment and all of the sudden some group users are unable to get access to the system. We have been looking this issue all day long and couldn't figure out what is broken in the system.
You can take as an example the following user's credential xyz . He has all sort of permission access to the site collection but unable to access sites within the site collection. He used to access all the sites a couple of days back.
Not everyone is noticing this issue. If I add this user to web application user policy he is able to access the site.
Yashwanth Mannem

This is a published site. superreader and superuser accounts are in web app user policy with appropriate permissions.
Yashwanth Mannem
Do you also have them in the Web Application properties in the correct format (classic or claims)?
Trevor Seward
Follow or contact me at...
&nbsp&nbsp
This post is my own opinion and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

TS3899 I upgraded to IOS 6, I am unable to get into my Yahoo mail. It accepts pw, and pops up and tells me how many e-mails I have and then goes right back to the sign on screen. verified that I can get in from laptop & wireless is functioning.any sugges

I upgraded to IOS 6, I am unable to get into my Yahoo mail. It accepts pw, and pops up and tells me how many e-mails I have and then goes right back to the sign on screen. verified that I can get in from laptop & wireless is functioning.any suggestions?

Purplehiddledog wrote:
I do backup with iCloud. I can't wait until the new iMac is available so that I can once again have my files in more than 1 location without needing to rely solely on the cloud.
I also rely on iTunes and my MacBook and Time Machine as well as backing up to iCloud. I know many users know have gone totally PC free, but I chose to use iCloud merely as my third backup.
I assume that the restore would result in my ability to open Pages and Numbers and fix the problem with deleting apps, but this would also mean that if my Numbers documents still exist solely within the app and are just not on iCloud for some reason that they would be gone forever. Is that right?
In a word, yes. In a little more detail.... When you restore from an iCloud backup, you must erase the device and start all over again. There is no other way to access the backup in iCloud without erasing the device. Consequently, you are starting all over again. Therefore, it would also be my assumption that Pages and Numbers will work again and that the deleting apps issues would be fixed as well.
If the documents are not in the backup, and you do not have a backup elsewhere, the documents could be gone forever.

I once created an account and changed meanwhile my Apple ID. Now, when trying to log in to iCloud, I get the message: "You are already logged in". I cannot get access to the account in the way, that, for example, the options appear on the right hand side.

I once created an account and changed meanwhile my Apple ID. Now, when trying to log in to iCloud, I get the message: "You are already logged in". I cannot get access to the account in the way, that, for example, the options appear on the right hand side.
What can I do?

Thank you, pvonk, but:
To be more precise: I am talking about the logging-in within the System Preferences on my iMac.
When trying to log in with the old ID, I get no access, i.e. it says "Try again"...-Trying the same with the new one gives me the result I mentioned in my first question...
Now I found out how to do it: I had to erase all accounts-then I could sign in with my Apple-ID. Thanks again.

I am unable to get past the apple login screens on my iPad to access my settings menu for a new home network. My password is not recognized so I cannot even get into the settings mode to make a chance. How can I get past the Apple logins?

I am unable to get past the apple login screens on my iPad to access my settings menu for a new home network. My Apple password is not recognized so I cannot even get into the settings mode to make a chance. How can I get past the Apple logins?

Hey Dpcupcake,
If you can not get past the sign in screen on your iPad, you will need to use the steps in this article to recover use of your iPad -
Forgot passcode for your iPhone, iPad, or iPod touch, or your device is disabled - Apple Support
Thanks for using Apple Support Communities.
Happy computing,
Brett L

I am unable to see, access, or navigate to, the far right side of iTunes 11.3.1.2 home screen on Dell Inspiron 3000 Windows 8.1 w/64-bit Pentium Processor.

I am unable to see, access, or navigate to, the far right side of iTunes 11.3.1.2 home screen on Dell Inspiron 3000 Windows 8.1 w/64-bit Pentium Processor.

Try dragging the window away from its location, resizing it, then maximizing it. There's been a bug since iTunes 11 that doesn't always size the window correctly if set to run maximized automatically (which I've notice most particularly on dual-screen systems).

Unable to get ip address from DHCP server for Aironet 1130AG Access Point

I have a network in which DHCP server is enabled. I have read the installation guide also there it is mentioned that 1130G Access point will not have any staic ip assigned to it.So it will automatically get the ip from the DHCP server from the network. I have connected that from the network but it is unable to get the ip address from the same. The same thing i have configured in the netgear it is coming fine. I have seen the sonic wall and used the IPSU tool also from checking the ip address from Mac Address but i am not able to get the same. Please provide me some tips to check where i am wrong in configuration because the first web page also not coming because of the ip address.

narendra,
I would suggest that the AP be connected to a laptop or desktop pc that would run a local dhcp server with a small scope setup...plenty of free ones on the web(this pc would obviously not be connected to your currnet network). This way you can watch the dhcp server hand the AP it's address (this can take a few minutes). Once you have the address use it to access the GUI and give the AP a static address (I find it good pratice to give all my autonomous AP's static addresses for ease of troubleshooting)...Hope that helps.

CFB2 unable to access Services Browser (unable to get metadata for CFC)

Hello --
I'm a novice with CF9.
== Scenario
- Mac OS X v10.6.8
- ColdFusion v9 [updated to latest 9.0.1]
- JRun with integrated WebServer [listen on 8500 port]
- Developer mode
- ColdFusion Builder v2.0.0 Build 277745 [standalone installation]
- Created a simple local CF9 server [localhost, local, 8500, ServerHome /Applications/ColdFusion9, ServerRoot /Applications/ColdFusion9/wwwroot]
- Enabled Debugger Mode in ColdFusion Administrator, test debugger ok, no problem
- RDS Viewer ok
- I'm able to open localhost:8500/CFIDE/administration without any problem
- I'm able to browsing CFIDE WebServer
== Problem
Within CFB2, when I try to open my local CF9 server to inspect RDS Server, I'm unable to view/introspect CFC Components.
I receive an error message "Unable to get meta data for cfc".
- In effect, trying to open cfcexplorer.cfc in componenutils path, I receive a 404 error
== Server Details
Server Details
Server Product
ColdFusion
Version
9,0,1,274733
Edition
Developer
Serial Number
Developer
Operating System
Mac OS X
OS Version
10.6.8
Adobe Driver Version
4.0 (Build 0005)
JVM Details
Java Version
1.6.0_24
Java Vendor
Apple Inc.
Java Vendor URL
http://www.apple.com/
Java Home
/System/Library/Java/JavaVirtualMachines/1.6.0.jdk/Contents/Home
Java File Encoding
MacRoman
Java Default Locale
it_IT
File Separator
Path Separator
Line Separator
Chr(10)
User Name
gobbo67
User Home
/Users/gobbo67
User Dir
/Applications/Adobe ColdFusion Builder 2/CFBuilder.app/Contents/MacOS
Java VM Specification Version
1.0
Java VM Specification Vendor
Sun Microsystems Inc.
Java VM Specification Name
Java Virtual Machine Specification
Java VM Version
19.1-b02-334
Java VM Vendor
Apple Inc.
Java VM Name
Java HotSpot(TM) 64-Bit Server VM
Java Specification Version
1.6
Java Specification Vendor
Sun Microsystems Inc.
Java Specification Name
Java Platform API Specification
Java Class Version
50.0
== Extract from application.log
25-giu-2011
22.21
Error
web-29
File not found: /CFIDE/componentutils/cfcexplorer.cfc The specific sequence of files included or processed is: /Applications/ColdFusion9/wwwroot/CFIDE/componentutils/cfcexplorer.cfc''
25-giu-2011
22.21
Error
web-29
Exception thrown by error-handling template:
25-giu-2011
22.21
Error
web-29
File not found: /Applications/ColdFusion9/wwwroot/WEB-INF/exception/coldfusion/runtime/TemplateNotFoundEx ception.cfm The specific sequence of files included or processed is: /Applications/ColdFusion9/wwwroot/WEB-INF/exception/coldfusion/runtime/TemplateNotFoundEx ception.cfm''
== Extract from exception.log
"Error","web-29","06/25/11","22:21:10",,"File not found: /Applications/ColdFusion9/wwwroot/WEB-INF/exception/coldfusion/runtime/TemplateNotFoundEx ception.cfm The specific sequence of files included or processed is: /Applications/ColdFusion9/wwwroot/WEB-INF/exception/coldfusion/runtime/TemplateNotFoundEx ception.cfm'' "
coldfusion.runtime.TemplateNotFoundException: File not found: /Applications/ColdFusion9/wwwroot/WEB-INF/exception/coldfusion/runtime/TemplateNotFoundEx ception.cfm
My problem is probably similar to http://forums.adobe.com/thread/503319
Any suggest is appreciate.
Alex/

Hello --
after spending many hours I'm believe that probably my concern arent related to CFBuilder [or not only] but also with CF9 installation on Mac OS X.
Attached you can find screen-shot about second page of Server Setup. Please note that I have configured a *local* server (not remote) with a developer environment.
Additional info; after checking in detail, I have noted that integrated WebServer (that I'm believe is JRun based) listen on 8500 is unable to open any .cfm page.
Under a directory created in WebRoot [Applications\ColdFusion9\wwwroot\Education] I have created a dumb index.cfm page, but that isnt executed.
But whem I go in CFIDE\administration all is working nicely.
Where can I check about integrated WebServer configuration, handler, etc?
== Error from Local CF9 server.log
27/06 09:02:01 error Requested resource 'File not found: /Education/index.cfm' (File%20not%20found%3a%20%2fEducation%2findex.cfm) not found
java.lang.IllegalStateException
      at jrun.servlet.JRunResponse.getWriter(JRunResponse.java:205)
      at jrun.servlet.JRunResponse.sendError(JRunResponse.java:597)
      at jrun.servlet.JRunRequestDispatcher.invoke(JRunRequestDispatcher.java:316)
      at jrun.servlet.ServletEngineService.dispatch(ServletEngineService.java:543)
      at jrun.servlet.http.WebService.invokeRunnable(WebService.java:172)
      at jrunx.scheduler.ThreadPool$DownstreamMetrics.invokeRunnable(ThreadPool.java:320)
      at jrunx.scheduler.ThreadPool$ThreadThrottle.invokeRunnable(ThreadPool.java:428)
      at jrunx.scheduler.ThreadPool$UpstreamMetrics.invokeRunnable(ThreadPool.java:266)
      at jrunx.scheduler.WorkerThread.run(WorkerThread.java:66)
== About starting server.log
"Information","main","06/27/11","08:49:04",,"Starting logging..."
"Information","main","06/27/11","08:49:04",,"Starting license..."
"Information","main","06/27/11","08:49:04",,"Invalid ColdFusion 9 license."
"Information","main","06/27/11","08:49:04",,"Invalid ColdFusion 9 license."
"Information","main","06/27/11","08:49:04",,"Developer Edition enabled"
"Information","main","06/27/11","08:49:04",,"Starting crypto..."
"Information","main","06/27/11","08:49:04",,"Installed JSafe JCE provider: Version 3.6 RSA Security Inc. Crypto-J JCE Security Provider (implements RSA, DSA, Diffie-Hellman, AES, DES, Triple DES, DESX, RC2, RC4, RC5, PBE, MD2, MD5, RIPEMD160, SHA1, SHA224, SHA256, SHA384, SHA512, HMAC-MD5, HMAC-RIPEMD160, HMAC-SHA1, HMAC-SHA224, HMAC-SHA256, HMAC-SHA384, HMAC-SHA512)"
"Information","main","06/27/11","08:49:04",,"Starting security..."
"Information","main","06/27/11","08:49:04",,"Starting scheduler..."
"Information","main","06/27/11","08:49:04",,"Starting WatchService..."
"Information","main","06/27/11","08:49:04",,"Starting debugging..."
"Information","main","06/27/11","08:49:04",,"Starting sql..."
"Information","main","06/27/11","08:49:05",,"Pool Manager Started"
"Information","main","06/27/11","08:49:05",,"Starting mail..."
"Information","main","06/27/11","08:49:05",,"Starting runtime..."
"Information","main","06/27/11","08:49:05",,"CORBA Configuration not enabled"
"Information","main","06/27/11","08:49:05",,"Starting cron..."
"Information","main","06/27/11","08:49:05",,"Starting registry..."
"Information","main","06/27/11","08:49:05",,"Starting client..."
"Information","main","06/27/11","08:49:06",,"Starting xmlrpc..."
"Information","main","06/27/11","08:49:06",,"Starting graphing..."
"Information","main","06/27/11","08:49:07",,"Starting verity..."
"Information","main","06/27/11","08:49:07",,"Starting solr..."
"Information","main","06/27/11","08:49:07",,"Starting archive..."
"Information","main","06/27/11","08:49:07",,"Starting document..."
"Information","main","06/27/11","08:49:07",,"Starting eventgateway..."
"Information","main","06/27/11","08:49:07",,"Starting FlexAssembler..."
"Information","main","06/27/11","08:49:07",,"Starting .NET..."
"Information","main","06/27/11","08:49:07",,"Starting Monitoring..."
"Information","main","06/27/11","08:49:07",,"ColdFusion started"
27/06 08:49:07 user ColdFusionStartUpServlet: ColdFusion: application services are now available
27/06 08:49:07 user CFMxmlServlet: init
27/06 08:49:07 user CFMxmlServlet: Macromedia Flex Build: 87315.134646
27/06 08:49:07 INFO Macromedia Flex Build: 87315.134646
27/06 08:49:08 user CFSwfServlet: init
27/06 08:49:08 user CFCServlet: init
27/06 08:49:09 user FlashGateway: init
27/06 08:49:09 user MessageBrokerServlet: init
27/06 08:49:09 user CFFormGateway: init
27/06 08:49:09 user CFInternalServlet: init
27/06 08:49:09 user WSRPProducer: init
27/06 08:49:10 user ServerCFCServlet: init
Server coldfusion ready (startup time: 10 seconds)
06/27 08:49:20 [Thread-15] WARN PDFM_W19004: The system font "/Library/Fonts/Baskerville.ttc" could not be loaded.
com.adobe.fontengine.font.InvalidFontException: Data could not be copied
      at com.adobe.fontengine.font.opentype.FontFactory$TableToLoad.load(Unknown Source)
      at com.adobe.fontengine.font.opentype.FontFactory$FontToLoad.load(Unknown Source)
      at com.adobe.fontengine.font.opentype.FontFactory$TTCToLoad.load(Unknown Source)
      at com.adobe.fontengine.font.opentype.FontFactory.load(Unknown Source)
      at com.adobe.fontengine.font.opentype.FontFactory.load(Unknown Source)
      at com.adobe.fontengine.fontmanagement.FontLoader.loadFont(Unknown Source)
      at com.adobe.fontengine.fontmanagement.FontLoader.load(Unknown Source)
      at com.adobe.internal.pdfm.util.FontSetBuilder.loadFontsPath(FontSetBuilder.java:385)
      at com.adobe.internal.pdfm.util.FontSetBuilder.loadFontsPath(FontSetBuilder.java:472)
      at com.adobe.internal.pdfm.util.FontSetBuilder.initFonts(FontSetBuilder.java:175)
      at com.adobe.internal.ddxm.Executive.initFonts(Executive.java:573)
      at coldfusion.document.DocumentServiceImpl.callAssemblerInitFonts(DocumentServiceImpl.java:1 249)
      at coldfusion.document.DocumentServiceImpl.initializeDocumentService(DocumentServiceImpl.jav a:230)
      at coldfusion.document.DocumentServiceImpl.access$000(DocumentServiceImpl.java:52)
      at coldfusion.document.DocumentServiceImpl$1.run(DocumentServiceImpl.java:180)
27/06 08:53:14 user RDSServlet: init
27/06 08:53:14 user RDSServlet: init
27/06 08:53:14 user RDSServlet: init
27/06 08:53:14 user RDSServlet: init
27/06 08:53:14 user RDSServlet: init
27/06 08:53:14 user RDSServlet: init
27/06 08:53:14 user RDSServlet: init
27/06 08:53:14 user RDSServlet: init
27/06 08:53:14 user RDSServlet: init
27/06 08:53:14 user RDSServlet: init
27/06 08:53:14 user RDSServlet: init
27/06 09:00:52 user FileServlet: init

HT1338 i am unable to get my serial number right after updating my logic pro

i am unable to get my serial number for pro logic right after updating the software

If you bought the boxed set of Logic Studio 2.0 which includes LP9, then you cannot download it. You must use the disks that came as part of the boxed set... to install from.
If you bought the App Store version of Logic Pro 9 then go to the Mac App Store App, Sign into the Store using the same Apple ID you used to purchase LP originally, look under the Purchase Tab and you shouldl find LP9 ready and waiting for you to download and install.

FSL-02007 Unable to set access rights of saploc.

Hello,
I am performing an installation of SAP ERP 6.0 EHP4 on Windows 2008 Server R2 along with MS SQL Server 2005 SP3 on a High Availability cluster.
I have completed the MS SQL Server 2005 into the first Cluster of MSCS. Performed the moving the MSCS groups of database, SAP and Cluster groups with success.
I created a shared file: sapmnt under the directory: E:\usr\sap for Everyone, & administrator with full access. The shared file was created as
SAPCLUSTER\sapmnt.
Then I started to execute the installation of Central Services Instance for ABAP (ASCS).
I logged as DECORCENTER.administrator, executed the command sapinst SAPINST_USE_HOST=DECORSAP
The installation has stopped after an error:
WARNING[E] 2010-10-25 16:59:51.285 [synxcfsexp.cpp:158]
           CSyFSExportImpl::setACL(acl)
FSL-02007 Unable to set access rights of saploc. SetNamedSecurityInfo: This shared resource does not exist.
Physical hostname of cluster is: SRVSAP01 y SRVSAP02
The cluster has three group resources:
ClusterGroup -> hostname: CLUSTERGROUP
ClusterSAP     -> hostname:CLUSTERSAP
ClusterDB       -> hostname: DECCENSAP
VIRTUAL SERVER -> hostname: DECORSAP
Let me know what I am doing wrong with this
Regards,
Rodolfo
Edited by: Rodolfo Neuhaus Wiese on Oct 25, 2010 7:26 PM

Ivan Bronner wrote:
Hi
>
> We tried the installation already with or without sapinst SAPINST_USE_HOSTNAME= "virtual hostname".
>
> Ivan
Hi,
Could you try to create "saploc" share manually and set share permissions to "Administrators, sap_localadmin" group, with full access? If you tried this before, did you face with a problem?
You should perform this activity with the same user that you've executed SAPINST
Best regards,
Orkun Gedik
Edited by: Orkun Gedik on Aug 24, 2011 11:33 AM

Unable to get access to 'rights' of a volume

Similar Messages

Maybe you are looking for