Unable to get IP on one ssid of a two ssid autonomus 1141 AP
We recently added a second ssid at a remote site AP but the clients cannot get an IP. They get associated to the AP but no IP.
The ssid we added is using the default vlan 1 which is where the dhcp server is located.
The other ssid vlan 101 is the visistor network and it gets an ip from the ASA. It works just fine.
The AP is connected to a 3560 swtich like so:
interface GigabitEthernet0/48
description link to WAP
switchport trunk encapsulation dot1q
switchport mode trunk
load-interval 30
If we put a static reservation in the dhcp for the client mac address it works fine. But dynamic dhcp does not work.
Attached is the config of the AP.
Vlan 1 is the ssid that does not get a dynamic IP.
Your config looks good, but like Rasika mentioned, I would remove infrastructure-ssid optional just to see if it works... now I would also configure a port on the same switch as the ap is connected to and set that to vlan 1 and make sure that laptop gets an ip address.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
Similar Messages
-
help! I recently upgraded my iphone to the latest IOS but my GPS seems to have a problem... I am unable to get directions from one point to another ... how do I solve this problem?
If using the built-in Maps app, directions are not available everywhere. Read here:
http://www.apple.com/ios/feature-availability/#maps-directions
If that's your problem, download the Google Maps app. -
Unable to get files from one computer to another... Help!
I have files on my iPod that have been from purchases a while ago that cannot be transferred through my purchase history. What I am trying to do is transfer the files from my iPod, to my new laptop, without erasing the files on the iPod. I have already transferred all the purchases it allowed me to, but I do not know how to transfer the other files... Including videos.
For all other non purchased music (your own CDs etc) try this method which works on some Windows PCs.
Enable your iPod for disk use.
See: iPod Disk Use.
Open iTunes and select edit/preferences/advanced/general. Put a check mark in the box marked "copy files to iTunes music folder when adding to library" and also "keep iTunes music folder organized", then click 'ok'.
Connect the iPod whilst holding down the shift/ctrl keys to prevent any auto sync, and if you see the dialogue window asking if you want to sync to this itunes library, click 'no'.
Then go to file/add folder, open 'my computer', select your iPod and click 'ok'.
The music files should transfer to your iTunes.
If this doesn't work (and it may not because officially it's not supposed to), check out the instructions/suggestions here.
Music from iPod to computer (using option 2). This a manual method using "hidden folders" and although it works, it can be messy.
Much easier ways are to use one of the many 3rd party programs that copy music from the iPod to the computer.
One of the most recommended is Yamipod. This is a free program that transfers music and playlists etc from iPod back to the computer. However, it does not transfer playcounts/ratings etc.
Another free program is Pod Player.
There is also CopyPod. This does preserve ratings/playcounts etc if those are important to you but this program is not free. It also supports video transfer. -
Unable to get Sky deal - SO FUSTRATING!!!! PLEASE HELP!!!!!
Hello My Sky account has been cancelled and I am unable to get a new one. I wanted to let someone or anyone know what happened. Firstly I applied for your free broadband plus sky talk half price for a year and £100 bill credit deal a few days ago. I registered my interest and got a code which went live on Friday 19/06/2015. After receiving the live email I went online and entered all my details as requested. During this time I entered online that I was looking for an additional line and not main line take over as I rent a room in a house but when the confirmation receipt came through it said I had selected main line take over which was not the case. I called first the customer services team (which took 15 minutes of being on hold to get through) and then I called the broadband team (which took 25 minutes of being on hold). After speaking to the broadband team the agent was surprised the main line option had been selected and there was NO associated phone number on the confirmation receipt. The agent advised this was very unusual and he would have to cancel the whole order as he could not switch to the option for a additional line. I advised the agent of the deal I had selected and advised him I had received a special code via email for this deal. The agent advised The code I used was no longer valid as it had been associated with the cancelled deal and I would have to apply or a new one. I said ok, the agent cancelled the deal, refunded my £5 upfront payment and over a hour of being on the phone later, the deal was officially cancelled. I then went back to apply for another code online and found all the codes had been used, I got the message "no more codes available". I wasted 2 hours of my life trying to join sky only to be left with a 2 hour phone bill and NO broadband or Sky talk. This was the most frustrating experience I have ever had with any customer services department. Can anyone help??
Was thinking of joining Sky, infact to my knowledge I had joined, but sadly the story goes on and becomes a nightmare... I even paid Sky's sub-contractor in Glasgow up front the £10 fee to instal the package I agreed to, until I woke up today to an email saying Sky had attempted to contact me unsuccessfully and has canceled my contract to join. I then sat on an 0800 number for 30 minutes (and still counting...) to resolve the problem, leaving work early in order to do so... Still no luck. I think I'll go back to BT. What a horrific experience!
-
I have two libraries on separate computers. If i turned itunes match on in both computers would the two libraries merge? So if my iphone normally syncs with my laptop would i still only get the iphones library or would i get both as one?
Yes, the two libraries should merge. However, you need to turn on match on one computer and let it finish before adding the second library.
Once you turn march on n your phone then you don't sync it with iTunes, but the merged library will show up on the phone. If you don't turn on match on your phone and continue to sync then all of the music from both libraries should be available to sync to it.
The only bit I can't confirm is what happens if you try to sync music to the phone which isnt actually downloaded into iTunes. Im not in a position to test that, but maybe someone else can help. -
My old computer crashed and I had to get a new one. I was unable to save anything from the old computer. Is there anyway to get my music from my Ipod to my new computer without having to start over with the old cd's again
Hello cheech07,
The following article contains directions that can help get you back on track with iTunes. I'd recommend picking up at 'Part 5' of the 'External drive' section.
iTunes: How to move your music to a new computer
http://support.apple.com/kb/HT4527
Cheers,
Allen -
I am unable to get Lightroom Mobile to work on my home network. The Ipad says "There are no collections to sync, enable lightroom mobile on your computer", but it is enabled. I got it to work one time on another network but not at home where I use Lightroom.
Hi,
could you please give us some info on what kind of network you have?
Can other application communicate with the web?
Thanks,
Ignacio -
RE:case#426486986 no one called me, only e-mail, I just need refund, I have been trying to reach iTunes for the last 2 month! unable to get help! 818-800-7400
yes
-
I am unable to get my iPhone5 to send photos via airdrop, recieving is fine.
Bluetooth and wifi are enabled.http://support.apple.com/kb/HT5887?viewlocale=en_US&locale=en_US
This has solved the issue, The other device that i tried to pair with and use airdrop had no icloud account, trie wit another device and all ok. -
Error while applying a patch "Unable to get the database connection"
Dear Experts,
A patch which got successfully applied is failing Production and the error is kind of surprising to me.
Apps version is 11.5.10.2
db version is 10.2.0.4
The worker log file shows
Time when worker restarted job: Thu Nov 24 2011 22:14:52
Start time for file is: Thu Nov 24 2011 22:14:52
adjava -ms128m -mx256m -nojit oracle.apps.fnd.odf2.FndXdfCmp &un_apps &pw_apps &un_apps &pw_apps &jdbc_protocol &jdbc_db_addr table &fullpath_pa_patch/115
Reading product information from file...
Reading language and territory information from file...
Reading language information from applUS.txt ...
Temporarily resetting CLASSPATH to:
"/erp/oracle/prodappl/ad/11.5.0/java/adjri.zip:/usr/java14/jre/lib/charsets.jar:/usr/java14/jre/lib/core.jar:/usr/java14/jre/lib/graphics.jar:/usr/java1
Calling /usr/java14/bin/java ...
Exception occured
Copyright (c) 2003 Oracle Corporation
Redwood Shores, California, USA
XDF(XML Object Description File) Comparison Utility
Version 1
NOTE: You may not use this utility for custom development
unless you have written permission from Oracle Corporation.
Unable to get the database connection using schema username/passwordIo exception: The Network Adapter could not establish the connection
AD Run Java Command is complete.
Copyright (c) 2002 Oracle Corporation
Redwood Shores, California, USA
AD Java
Version 11.5.0
NOTE: You may not use this utility for custom development
unless you have written permission from Oracle Corporation.
AD Worker error:
The above program failed. See the error messages listed
above, if any, or see the log and output files for the program.
Time when worker failed: Thu Nov 24 2011 22:14:53
{code}
The error says database connection error. I am able to connect to the database using sqlplus. I tried to restart the failed worker, but the same error is repeating.
Any help would be appreciated.
Thanks
qARS
Edited by: user7640966 on Nov 24, 2011 9:07 AMHussein,
One thing which I noticed now is in the apps Tier the
tnsnames.ora under $TNS_ADMIN
shows entry like this:
PROD=
(DESCRIPTION=
(ADDRESS=(PROTOCOL=tcp)(HOST=<appsServerName>)(PORT=1521))
(ADDRESS=(PROTOCOL=tcp)(HOST=<dbServer>)(PORT=1521))
(CONNECT_DATA=
(SID=PROD)
)Actually *(ADDRESS=(PROTOCOL=tcp)(HOST=<appsIPaddress>)(PORT=1521))* this line in the tnsnames.ora is not correct. In fact the appsServerName should be replaced with dbServerName
I deleted the tnsnames.ora and reran autoconfig but it is again recreating the same entry.
Any clue how this can be fixed?
Thanks
qARS -
Sony DCR-DVD505 Handycam: Unable to get video clips, audio
Evaluating Adobe Premier. Hopefully helpful for other Sony DCR-DVD505 users.
Objectives:
1) Get videos from Sony DCR-DVD505 handycam into Premier Elements
2) Drag and drop various clips into Sceneline
3) Insert menu markers
4) Burn DVD
Stuck in Step 1, getting video from handycam, unable to get video clips (with audio)
First Try: NO AUDIO.
The Sony DCR-DVD505 burns a mini-DVD (1.4 GB) while recording. After "finalizing" the disk, the media may be imported into the computer. Streaming was supported by Windows XP driver but is no longer supported in Windows Vista. In fact, Vista Service Pack 2 (SP2) does not even recognize the camera as a DVD drive! So downgraded to Vista SP1 and used the Sony Picture Motion Browser to import media into computer as MPG files. Each MPG file is a clip (corresponding exactly to camera record on-off sequence while shooting). Then opened up Adobe Premier Elements 8. Used get media to import all the MPG clips into "Organize". Dragged and dropped various clips...inserted a menu or two and...burned the DVD. PROBLEM: VIDEO OK, BUT NO AUDIO(?!). The MPG files on computer play fine (with audio) inside Windows Media Players. Read all sorts of nonsense about why Adobe Premier (probably old versions) cannot work with "low-quality/compressed" MPG and needs to be a particular type AVI soo....
Second Try: Capture VOB directly
Forget the camera. Insert the mini-DVD directly into computer DVD drive, create a new project and followed directions from "Lowdown on VOB" http://forums.adobe.com/message/2117743 and "tools to convert to DVI" http://forums.adobe.com/thread/415317. I loaded the VOB directly and dropped them into Timeline as advised by the second post (only hitch being the first VOB pertaining to the DVD menu is not recognized and is neither needed).
However, File > Export is always GREYED out (unusable). And the status at bottom right seems to be looping on "Background Rendering". DO I WAIT? In any case, the whole video is showing up as a single continuous stream and what I want are the clips from the camera?!
Then I tried Prism (again as per the second forum post mentioned above). It simply did something to process 30 minutes of video and crashed in the end without explanation - saying there was an error in conversion.
Is this AVI conversion even a good idea? How would I get my clips back??
Bottomline. My mini-DVD and imported MPGs plays fine in Windows Media Player. However unable to extract the camera clips (with audio).Dawg, I have the Sony DCR-DVD305, and have been using it successfully for quite a while with PE7, with few issues, once I had a workflow nailed down.
I believe the 505 is basically the same camera, with some additional features.
This workflow worked for me in the past so I'll pass that along:
Sony Browser to PC as Mpeg.
Mpeg to Windows Movie Maker, output to DV-AVI, taking default settings.
DV-AVI imported into PE7.
This should also work for PE8.
Upon getting Cyberlinks PowerDirector v7, my new workflow changed to this:
I take the min-DVD directly from camcorder to my PC, and capture the disk via Power Director.
PD will convert the VOB's directly to DV-AVI Type 2 on one pass.
I then load this DV-AVI into PE7.
(PD v7 was pre-installed on my new PC from HP, or it can be purchased from Cyberlink).
Other options to try:
Copy the VOB's directly from the mini-DVD to your PC and use Prism to convert these to AVI.
Or load the VOB or Mpeg into PE, then use that to convert to AVI.
(Export to DV-AVI with PE8 is done with SHARE/PC, not Export under the File Menu, which is greyed out).
I've had many issues trying to work with Mpeg's and VOB's when loaded directly to PE with limited success.
So if you can get it converted successfully to AVI outside of PE, I've found this to be a better approach.
Post results, if any of this works for you...
Note: One other thing, if you are working directly with VOB's to PE, especially multiple VOB's from a single DVD, you can encounter out-of-sync issues between video and audio. If this occurs, review this link from Muvipix:
http://muvipix.com/phpBB3/viewtopic.php?f=38&t=2469: -
Unable to get SQL Server Agent to run after installing SQL 2012 Standard with SP1
I am unable to get SQL Server Agent to run after installing SQL 2012 Standard with SP1. Log message is as follows:
Attempting to load library 'xplog70.dll' into memory. This is an informational message only. No user action is required.
Failed to verify Authenticode signature on DLL 'C:\Program Files\Microsoft SQL Server\MSSQL11.MSSQLSERVER\MSSQL\Binn\xplog70.dll'.
Error: 17750, Severity: 16, State: 0.
Could not load the DLL xplog70.dll, or one of the DLLs it references. Reason: (null).Hi JFriedley,
According to your error message, there might three reasons for this issue.
xplog70.dll is corrupt, you need to check if you have any SQL Server running on same file version and same production
edition. If xplog70.dll is corrupt, you can copy it from the new server where agent is running fine to your problematic server.
Native client not installed properly. If you try applying any latest Service Pack or Cumulative Update then check if the SQL Server Agent can start, if that also doesn’t solve issue then try to reinstalling SQL Server Native client from SQL Server setup
files.
There is a similar issue about error 17750, you can review the following article.
http://blogs.lostincreativity.com/sqldba/sqlserver-error-17750-could-not-load-the-dll-xpstar90-dll/
Regards,
Sofiya Li
If you have any feedback on our support, please click here.
Sofiya Li
TechNet Community Support -
DropDrown unable to get data in ALV
Hi,
I'm trying to put an dropdown by key (or index) into an ALV but I'm unable to get data in the dropdown. Can someone please help me with this?
I was watching this threads on topics at the forum, but I can not solve this problem.
Copy my code.
DATA: lr_col TYPE REF TO cl_salv_wd_column,
lr_dropdown TYPE REF TO cl_salv_wd_uie_dropdown_by_key,
l_cmp_usage TYPE REF TO if_wd_component_usage,
l_alv_model TYPE REF TO cl_salv_wd_config_table,
l_ref_interfacecontroller TYPE REF TO iwci_salv_wd_table.
l_cmp_usage = wd_this->wd_cpuse_doc_measure( ).
IF l_cmp_usage->has_active_component( ) IS INITIAL.
l_cmp_usage->create_component( ).
ENDIF.
l_ref_interfacecontroller = wd_this->wd_cpifc_doc_measure( ).
l_alv_model = l_ref_interfacecontroller->get_model( ).
l_alv_model = l_ref_interfacecontroller->get_model( ).
l_alv_model->if_salv_wd_table_settings~set_read_only( abap_false ).
lr_col = l_alv_model->if_salv_wd_column_settings~get_column(
id = 'VALEUR_DIFF' ).
CREATE OBJECT lr_dropdown
EXPORTING
selected_key_fieldname = 'VALEUR_DIFF '.
lr_col->set_cell_editor( lr_dropdown ).
DATA:
lo_nd_ctx_tab TYPE REF TO if_wd_context_node,
lo_ndinfo_ctx_tab TYPE REF TO if_wd_context_node_info,
lt_value_set TYPE TABLE OF wdr_context_attr_value,
ls_value_set TYPE wdr_context_attr_value.
ls_value_set-value = '01'.
ls_value_set-text = 'One'.
APPEND ls_value_set TO lt_value_set.
ls_value_set-value = '02'.
ls_value_set-text = 'Two'.
APPEND ls_value_set TO lt_value_set.
lo_nd_ctx_tab = wd_context->get_child_node( 'DOC_MEASURE' ).
lo_ndinfo_ctx_tab = lo_nd_ctx_tab->get_node_info( ).
lo_ndinfo_ctx_tab->set_attribute_value_set(
name = 'VALEUR_DIFF' value_set = lt_value_set ).
DATA: lt_valueset TYPE TABLE OF wdr_context_attr_value,
ls_valueset TYPE wdr_context_attr_value,
lr_node TYPE REF TO if_wd_context_node,
lr_nodeinfo TYPE REF TO if_wd_context_node_info.
lr_node = wd_context->get_child_node( 'DOC_MEASURE' ).
lr_nodeinfo = lr_node->get_node_info( ).
lr_nodeinfo->set_attribute_value_set(
EXPORTING
name = 'VALEUR_DIFF'
value_set = lt_valueset
Thanks.
Matías.Hi,
In your code, you are trying to do set_attribute_value_set twice. If you read your code carefully, you are setting the values once using lt_value_set where you have correctly filled the values. But after this, you are again trying using lt_valueset without filling any values. This is why your previous value-list gets overwritten and you see nothing in the dropdown. Remove the following lines in your code and it will work fine.
DATA: lt_valueset TYPE TABLE OF wdr_context_attr_value,
ls_valueset TYPE wdr_context_attr_value,
lr_node TYPE REF TO if_wd_context_node,
lr_nodeinfo TYPE REF TO if_wd_context_node_info.
lr_node = wd_context->get_child_node( 'DOC_MEASURE' ).
lr_nodeinfo = lr_node->get_node_info( ).
lr_nodeinfo->set_attribute_value_set(
EXPORTING
name = 'VALEUR_DIFF'
value_set = lt_valueset
Please get back if you are facing any more issues.
Regards,
Nithya -
Unable to get parameter by using a controller in OAF
Hi!
I'm new using OAF and will appreciate your help a lot!!
FYI:
Basically I have to add 2 descriptive flexfields in a page (by creating a VO) and I have to update the table with the information registered on those dff (I've done all the logic already).
I created a Controller (CO) which calls a method declared in an Application module (AM) that executes a store procedure (the CO and AM have been created by me and they extend a standard CO and AM).
Problem:
However, just before updating.. I'm having a problem because I'm unable to get a parameter by using paramContext.getParameter("reqHeaderId"); that will help me to identify which row I need to update.
Since the instruction is not capturing the value, it returns null and I got the following error when I try to convert it to Number: oracle.apps.fnd.framework.OAException: java.lang.NumberFormatException: null
It's really important to mention that before getting to the page where I click the submit button that does the logic mentioned.. there are 2 pages before the one where I'm trying to capture the parameter and the parameter needed is set on the 1st page. I've been checking each standard CO of the 3 pages and they use the instruction pageContext.putParameter("reqHeaderId"); to pass it between the 3 pages (As far as I know, if not please correct me). On the 3rd and last standard CO it uses pageContext.getParameter("reqHeaderId"); to get the value and do some other logic.
So why Im not getting the value if I do the same thing (pageContext.getParameter("reqHeaderId");) on my xxController (which extends the standard CO)?
Here is the code of the controller:
public class xxController extends standardController {
public void processRequest(OAPageContext pageContext, OAWebBean webBean)
super.processRequest(pageContext, webBean);
public void processFormRequest(OAPageContext pageContext, OAWebBean webBean)
super.processFormRequest(pageContext, webBean);
String str;
str = pageContext.getParameter("_FORM_SUBMIT_BUTTON");
if ((str != null) && (str.equals("SubmitButton")))
String ReqHeaderId = pageContext.getParameter("reqHeaderId");
String ReqLineId = pageContext.getParameter("reqLindId");
Serializable[] parameters1 =
ReqHeaderId
,ReqLineId
,pageContext.getParameter("xxavtBienServicio") //dff
,pageContext.getParameter("xxavtAttribute3") //dff
String var = (String)am.invokeMethod("updateAttributes", parameters1); // updateAttributes is the method that converts ReqHeaderId to number and executes my store procedure
thank you for your help in advance!You need to verify that the parameter is being added to the pageContext from the first page to the last. You can do this by downloading the pages and all the class files to your development environment and put them into the myClasses directory. Then once you get it so it can be run in JDeveloper, you can actually invoke the debugger and do a watch on the page context for that parameter. It is important to note that you may need to download more than just those specific pages depending upon the setups of the supporting pages. I generally find it easier to just download everything for a particular application to my classes directory so I am not forever trying to find missing class files. Even then if they call some utility classes, you will need to download them to the JDevelper on your PC into the classes directory. But once you are able to run the pages in JDeveloper you will be able to do a lot more with the debugger.
Kristofer -
Tecra A10 - Refurbished - unable to get it connected to my home network
I just got this Tecra A10-104 refurbished Laptop...before I take it back I am asking here just in case theres something I have missed as I am unable to get it connected to my home network.
I am running a Belkin Wireless Router that has 2 main PC's directly connected (LAN), and another PC wirelessly connected.
This is my router: http://www.belkin.com/uk/support/article/?lid=enu&pid=F5D8233uk4&aid=9238&scid=0
All PC's working fine and connected.
Now I'm trying to setup this laptop to connect.
I uninstalled the Vista Business and ussed the XP Pro Product Recovery disc that came with the Tecra.
My WiFi card is: Intel(R) Wireless WiFi Link 5100 (Driver Date: 27/04/2008 - Driver Version: 12.0.0.73)
It sees the network but no matter what i try just won't connect.
What I have done so far (read before suggesting stuff I have already tried):
Reconfigured routers WPS to Shared Key system.
Made sure the wireless adapter has settings set to 20/40hz (auto)
Restarted router, cable modem & laptop several times
Wireless button on side of Laptop is ON.
FN + F8 to enable WIFI (ON) BLUETOOTH (OFF)
Added wireless network to Auto Connect settings along with SSID and passcode end encryption method.
Clicked connect when network appears in network viewer dialogue and retyped passcode.
Not working.
I should add the Laptop has no problems connecting via its Gigabit LAN port.
Anything else I'm missing?
Thanks in advance.
EDIT: Dual post removed.UPDATE:
The next thing I tried was to reinstall Vista Business from recovery disc to see if this suffered from the same problem.
The wireless connection worked fine on Vista and, despite the updates that I was being offered, worked without needing to update any drivers.
This made me think...so the issue is probably XP DRIVER related.
What I have done now is backup all the driver updates I was told to download by TEMPRO (BIOS & wireless manager updates included).
I think part of the problem is that TEMPRO only works in Vista (not XP) so you are not informed of any updates that may be required if you downgrade to XP straight after purchase (which is what I did).
Maybe you are looking for
-
Yeah! When I launch Premiere Pro CC 2014 (on a PC, windows 7.1, 64-bit) I get this message: Sign in requiered. Please sign in with your Adobe ID. Also on screen is a text that is headlines: Terms and conditions for trial software. I have been using
-
How to get file path in the form \\filer01\dir\index.htm
Hi, after selecting a file using the FileChooser dialog, i would like to convert the file path like "H:\index.htm" into a form like "\\filer01\dir\index.htm". On my system, the logical device name H:\ is mapped to a directory on a file server "filer0
-
Parameters not available for run MAKT
Our system produced the above error message when running Dunning batch programs. The program was cancelled (terminated) after this message. Program is RFKK_MASS_ACT_SINGLE_JOB How do ensure that all the dunning parameters are OK in Transaction Code F
-
I have this problem were whenever I'm on safari it will shutdown on me after 5-10 mins of use. The screen turns black for about 5 seconds and then it goes back to the home screen. When I go back to safari the last web page I was on is gone and I have
-
BW Hierarchy Vs BO Universe Hierarchy
Hi, Can any one tell which one is the better one to create hierarchy in BW and use it in BEX based universe or direclty creating the hierarchy in BO Universe. Thanks in Advance for giving the answers. Thanks, Dru