Unable to get to page 2 of the BIOS configuration on R200

I have a Portege R200 that needs to be reinstalled, but I am unable to navigate to the second page of the BIOS to change the boot sequence. Using pgup/pgdn does nothing as well as every other key sequence I have tried including F12 and holding down 'C' at startup. I have even tried removing the CMOS battery and shorting out the reset soldier points on the motherboard for 30 seconds as suggested by my research. In addition, I have attempted flash the BIOS using the latest available download from Toshiba, but I was confronted with an error message stating that I am not authorized to perform the upgrade and I need to reboot and try again with supervisor permission.
Currently I can boot from USB/CD-Rom only when the hard drive is disconnected which doesn't do me any good. Being that the Hard drive is a 1.8" and I don't have an adapter for it, there isn't much I can do with it. Any advice I can get will be much appreciated.

Hi Narendra,
The below are standard Cause and action
Cause 
The report contains structural errors. This means that Web Intelligence cannot decode the report and display the results.
Action 
Do one of the following:
View the report in Structure View and verify the report structure. For example, errors can be caused if report blocks overlap or if the structure of a table contains cells that create an asymmetrical table format. Modify the report structure appropriately.
Contact your administrator and request them to search for structural anomalies in the report.
I have seen this error in my experience in the below cases, it definitely is related to structure.
Reports with merged dimensions where blocks with incompatible objects placed in structure mode, are previewed for results.
Reports with sections where some sections created are no longer valid objects in the report.
You can duplicate the report keeping it in structure mode and then preview results, if it still throws error and does not display, then have to investigate the block/object/cells of the structure that is causing this issue by deleting one by one from duplicate report and preview results repeatedly, that way wherever you get right preview, the deletion before that is the affecting block/object/cell.
Thanks
Arvind Shukla

Similar Messages

  • I am unable to print "ALL Pages" using the Adobe Print plugin in Firefox, only the first page gets printes. however IE works perfectly fine.Please advise. Is it some way that firefox identifies the complete web page..? PLease help

    I am unable to print "ALL Pages" using the Adobe Print plugin in Firefox, only the first page gets printes. however IE works perfectly fine.Please advise. Is it some way that firefox identifies the complete web page..? PLease help

    Does the entire webpage appear in Print Preview? <br />
    File > Print Preview

  • I'm unable to bookmark a page in the folde I want. Only two of my folders is hown. HOW DO i SEE THEM ALL?

    I have never found Firefox's bookmarking very intuitive- only frustrating. I am unable to bookmark a page into the folder I want because only two of my folders are shown and they aren't the one's I want. How do I get all my folders shown when I hit bookmark this page? I have followed the instructions to no avail.

    I have never found Firefox's bookmarking very intuitive- only frustrating. I am unable to bookmark a page into the folder I want because only two of my folders are shown and they aren't the one's I want. How do I get all my folders shown when I hit bookmark this page? I have followed the instructions to no avail.

  • StatelessSession Example: We were unable to get a connection to the WebLogic server at t3://localhost:7001

    I have seen other related posts on this site but really no answers, the users seem to be left hanging.
    Anyway, I am trying to run the statelessSession example, with the WebLogic server running and listening
    on port 7001 on the current machine (i.e. localhost).
    Here is what I am seeing:
    c:\weblogic\myserver\clientclasses>java examples.ejb.basic.statelessSession.Client
    Beginning statelessSession.Client...
    We were unable to get a connection to the WebLogic server at t3://localhost:7001
    Please make sure that the server is running.
    System Configuration:
    Win2000, WebLogic 5.1, WL Sp2, Java 1.2.2, weblogic home==> c:\weblogic
    I have attached the weblogic.log.
    Regards,
    John

    Hello John,
    When I first install "weblogic", I am successfully able to run the examples, but after some time which I completely forget how I make them run, I install it again and encounter the same problem as you.
    After spending nearly a whole day on restarting computer, viewing ports etc. :) :(, I remember that I make weblogic run from the command line. First, in a console run setenv and startWebLogic tools which are located under weblogic directory and in an another console run setenv again(for possible errors, I want to be sure that it is correct again) and run your client as explained in the tutorials html pages.
    As seen, in computer science, simple things, not hard things, always cause you to lose time :)))
    Best regards
    Banu
    "John Pda" <[email protected]> wrote:
    >
    I have seen other related posts on this site but really no answers, the users seem to be left hanging.
    Anyway, I am trying to run the statelessSession example, with the WebLogic server running and listening
    on port 7001 on the current machine (i.e. localhost).
    Here is what I am seeing:
    c:\weblogic\myserver\clientclasses>java examples.ejb.basic.statelessSession.Client
    Beginning statelessSession.Client...
    We were unable to get a connection to the WebLogic server at t3://localhost:7001
    Please make sure that the server is running.
    System Configuration:
    Win2000, WebLogic 5.1, WL Sp2, Java 1.2.2, weblogic home==> c:\weblogic
    I have attached the weblogic.log.
    Regards,
    John

  • Unable to get Window Handle for the 'AxCrystalActivXViewer' control.

    Hi,
    I have Operating System : Windows 7 and Application developed in VS 2005 and I am using Crystal Report XI licenced version.
    But when I am trying to use TTX(Field Defination) based reports it gives me "Unable to get Window Handle for the 'AxCrystalActivXViewer' control. Windowless ActivX Controls are not supported."
    Please provide me solution for this ASAP as I am stucked on this from long lomg time.
    -Regards
    Swapnil

    Appears you are installing an upgrade version.
    Use these links:
    http://downloads.businessobjects.com/akdlm/crystalreports/crxir2_sp4_full_bld_0-20008684.exe
    http://downloads.businessobjects.com/akdlm/crystalreports/CRYSTALREPORTS06_0-20008684.EXE

  • I have been working on the same numbers file for the past few weeks.  The last time I opened it was 1 week ago.  Today when I tried to open it I am unable and getting a message that the file is invalid and the index.xml file is missing.

    I have been working on the same numbers file for the past few weeks.  The last time I opened it was 1 week ago.  Today when I tried to open it I am unable and getting a message that the file is invalid and the index.xml file is missing. 

    Hi Tracie,
    I upgraded to Maverick OS X 10.9.5, numbers spreadsheet is saved. Upon re-opening, it appears to be frozen, a warning "file is invalid as index.xml file is missing". I checked, and the file is not "locked". This appears to occur only with using the new numbers app. When I open previous spreadsheets from old iWorks, no such problem occurs.
    How did you resolve your problem?
    Would appreciate any help here.
    Thanks,
    Deehay

  • I've upgraded the software on my iPad "The New iPad" as they call it to iOS 6 and I'm unable to get spoken directions on the turn by turn navigation. Does anybody know if this feature is available for the iPad? It's Siri compatible

    I've upgraded the software on my iPad "The New iPad" as they call it to iOS 6 and I'm unable to get spoken directions on the turn by turn navigation. Does anybody know if this feature is available for the iPad? It's Siri compatible
    Also I'm in Australia

    Yes, turn by turn directions is available on the new ipad. I've tried it and it does work.
    What problem are you having?

  • Unable to get a connection to the WebLogic server

     

    After reinstalling WLS and SP it still didn't work, however, after a 3rd
    reinstall in
    the DEFAULT directory of c:\weblogic, it finally worked! It would NOT work
    from c:\tools\weblogic. Who knows, maybe i didn't update a magic variable
    somewhere.
    -b
    "Bob Banks" <[email protected]> wrote in message
    news:397e0db2$[email protected]..
    Pablo, how did you fix your problem? Same thing happening here on Win2000,
    WLS5.1 SP4.
    Thx,
    -Bob
    "Pablo Corinkha" <[email protected]> wrote in message
    news:[email protected]..
    Trying to use the statelessSession EJB example. When attempting to run
    the client, I get the following message:
    Beginning statelessSession.Client...
    We were unable to get a connection to the WebLogic server at
    t3://localhost:7001
    Please make sure that the server is running.
    The WebLogic server is definitely running, though. I am able to access
    it using port 7001 from a browser. What could be wrong?

  • If I choose any i-works draft, I only can get one page not the complete draft

    If I choose any i-works draft, I only can get one page not the complete draft

    Mousing shows all the available pre-formatted page available in each template to give you an idea what is there, but you only get one, sometimes 2, when you create a new document. All of the other pages can be accessed via the Insert menu. Insert > Sections in word processing & Insert > Pages in page layout.
    If they all loaded when you opened a template, you'd have to go through & delete the ones you don't want & duplicate the ones you want more than one of.
    FYI: the name of the program is iWork, no 's' & no hyphen

  • Howdy apple people,  on my new ipad 3 i zoomed or something like that and every thing is way big and i am unable to get it back to the starting size  please i hope someone out their may help

    i inlarged or zoomed a pic and now everything is huge on my ipad 3   please help me get it back to the start size   while understanding what i did    i kinda shol sometimes  lol   please help

    pjl123 wrote:
    Stevejobs has the right answers, except I have a different set, in this case.  A double tap by 1 finger zooms the screen.
    A single finger double tap zooms the page/picture/paragraph, not the entire screen.
    This option is different. It zooms the entire screen, not just the page/picture/paragraph.
    This is enabled in Settings > General > Accessibility > Zoom.

  • 8520-unable to get email settings in the set up folder

    I have only had this for 2days and I am unable to get the emails working, in the set up tables the email setting icon is not there and when I try to set up the email in the set up wizard, email set up only gives 1 option ' I want to use a work email account with blackberry enterprise server' which I don't I wan to connect to my home email address with Sky Email

    This appears to be a common issue and there are several threads about this....
    I am having the same issue with msn email.  I got the message yesterday from Blackberry to change my password.  No luck in doing that nor in deleting the email service and adding it back.  I think this is on the Blackberry side of things not MSN.  I greatly depend on having mobile access to my email and this service level won't cut it.  So far Blackberry is a Fail for me due to this as well as a host of other things.  I guess it is time to go back to something else. 
    I'll keep trying and post back if my email service eventually gets successfully added back to my blackberry.
    Edited to add:  I tried adding my son's msn account and it set up just fine via the web at blackberry service and also again via email setup on my phone.  When I use the web based email setup process I receive an "invalid email or password: error.  When I use the blackberry handheld email setup application I get an error message that says "Unable to set up email.  Please try again."  Yes - I am sure I am using the right msn password - I have signed on to my account several times to be sure.  This is incredibly frustrating.  Any ideas at all?  Is this the only support that is available - asking other users? 

  • Unable to rerun OAF page in the same OC4J session

    Hi All,
    could you help me with running OAF page from JDeveloper.
    Configuration from OEBS:
    OA Framework 12.1.1
    Oracle OA Extension 10.1.3 - build 1089
    Business Components 10.1.3.3
    UIX (Cabo) 2_3_6_5
    BiBeans Runtime 3.1.1.9 nondebug BI Beans 3.1.1.x
    MDS 9.0.6.0.0_35
    XML Oracle XML Developers Kit 10.1.3.5.0 - Production
    AOL/J Applications Object Library, Core Java Roll Up Patch J
    Servlet 2.4
    Java 1.6.0_16
    JDBC Driver 11.1.0.7.0-Production
    My local computer configuration:
    OS: Windows Server 2003 SP2
    JDeveloper: p9172975_R12_GENERIC (for 12.1.1)
    Issue:
    My development database is located on remoute server and it takes about 10 min to run simple OAF page (it works correct then).
    But after modification of the page when I run it again, JDeveloper always opens new session (instead of using existed one) because of this error:
    C:\Oracle\JDeveloperR12\jdevbin\jdk\bin\javaw.exe -jar C:\Oracle\JDeveloperR12\jdevbin\j2ee\home\admin.jar ormi://10.24.166.61:23891 oc4jadmin **** -updateConfig
    Dec 29, 2009 1:23:06 PM com.oracle.corba.ee.impl.orb.ORBServerExtensionProviderImpl preInitApplicationServer
    WARNING: ORB ignoring configuration changes. Restart OC4J to apply new ORB configuration.
    So I have to wait again 10 min to see the changes :((
    If you have any experience regarding this issue I will appreciate you very much for help.

    Kumar,
    Ftping the PG.xml to mds folder will not help the page to goto MDS directory
    You have to import the file using xmlimporter
    I understand you have done the import, but it is not success.
    Could you please post what is the script you used to import the PG.xml
    and once you run what was the output you have got.
    May be you can refer the URL for the scripts
    http://apps2fusion.com/at/61-kv/331-oa-framework-scripts
    With regards,
    Kali.
    OSSI.

  • Unable to add Tab Pages in EH&S Configuring Tab Pages

    Hi,
    I am working on Integration of Time Management with Industrial Hygiene and Safety.
    In EH&S configuration under Industrial Hygiene and safety /Basic Settings/Configure Tab Pages ,When I select Object Type with work Area as 'AFP - Data on person affected' , I get the list of following tabs
    DESC     Treatment
    INJURY     Injury/Illness
    REPT     Ind Hyg. Safety Data
    I cannot see the TDAT  Time Data, when I tried to add new tabs , I can list the Time Data tab , but I cannot populate the selected Time data tab in the configuration.
    Please let me know if I need to do more settings and what settings should I do for this tab to appear.
    Please help me to resolve this issue asap.
    Thanks,
    Babitha

    Hi
    With SAP ECC 6.0 YOu must me having EHS 3.2
    With this TDAT comes as default setting,
    Although if it is not there what you can do is, Go to configure tab pages select object type work area as AFP. Click on append button. You will get field selection Client, Tab, Description. You tick mark on Clent and Tab. Select client 000 and Tab -TDAT and click on append.
    Hope this will work.
    Other wise if you wont to add new TAB you have to go to IMG activity "Assign Value Assignment Types to Classes "
    Create value assignment type, Give vategory, assign class then match up master data This will create new tab page. You have to create characteristics for the fields you want under this tab page.See the SAP help for this. Pl note that you can not create new tab using Configure tab pages.
    Regards
    Suhas

  • My iPad crashed when I updated latest iOS software. After resetting the system, I am unable to get back Pages, Numbers and Keynote Apps. Anyone has same problem? And how can I get back the apps?

    My iPad Air crashed after updating latest iOS software. After resetting the system, Pages, Numbers and Keynotes are not available. How do I get the apps back into my iPad?

    You can also re-download the apps.
    App Store>Purchased>Re-download apps

  • Unable to get login page after applying the 12.1.3 patch

    Hi
    I had applied the 12.1.3 patch 9239090. Just getting blank screen.
    Please advice me how to trouble shoot the login page in r12
    Thanks
    Reddy

    Hi Hussein
    Thanks for the excellent document.Here is the result of the url's
    Working Fine
    http://<server>.<domain>:<PORT>/OA_HTML/ServletPing
    http://<server>.<domain>:<PORT>/OA_HTML/jsp/fnd/aoljtest.jsp
    Failed the following
    http://<server>.<domain>:<PORT>/OA_HTML/OA.jsp?OAFunc=OAHOMEPAGE
    http://<server>.<domain>:<PORT>
    http://<server>.<domain>:<PORT>/OA_MEDIA/FNDLOGOL.gif
    http://<server>.<domain>:<PORT>/forms/frmservlet
    http://<hostname.domainname>:<port>/OA_HTML/fndvald.jsp?username=sysadmin&password=<sysadmin_password>
    Should I paste the log files here.
    Thanks
    Reddy
    Edited by: Reddy on Jun 26, 2011 9:32 PM

Maybe you are looking for

  • Regarding an update in my lumia 520

    I have updated my 520 a couple of days ago with lumia amber update...and now today it was showing me a new phone update. I tried to download the update but it got failed. After that i restarted my phone and it was showing no updates available. what w

  • How to fix click of death on External Hard Drive

    PLEASE PLEASE READ ALL!!!!!! My Hard drive is a: G-Drive slim 500GB EHD 5400RPM not sure on warranty. Here is the story. It all started when I was plugging in the HD in my sisters school laptop, when all of a sudden, an error popped up saying "You ne

  • Adobe Photoshop CS5 (Windows 7) Lagging Brushes & Tools

    What I'm Using: - Toshiba F60 Qosmio Laptop w/ Windows 7 - Adobe Photoshop CS5 (64 bit) Hey Everyone, I'm having an issue with my new Adobe Photoshop CS5 (64 bit) installed on my Brand new Laptop (Toshiba F60 Qosmio). Basically I have optimized via t

  • Viewing Stylesheet in Design view

    HI, Two of us are working on the same website, sharing the same files.  In our site set up we both are using the same shared drive with the files. When I view a page in design view it looks fine.  When the other person views the page in design view i

  • HELP! macbook pro won't boot correctly!

    Hello all, I hope someone can help! I bought my Macbook pro a couple of months ago and everything has been running smoothly. The other day when I was trying to connect my Macbook to my LCD TV, my system froze and became unresponsive. I turned the Mac