Unable to initialize hdv deck problem

Hi all,
I'm having the 'unable to initialize hdv deck' problem. I am trying to capture HD footage from a Sony HVR-A1E camera. iLink and down conversion are off (like they should be) and I have just captured a HD tape before the problem started.
I don't understand how I could capture HD footage just fine and then without touching any settings (just trying to start capture again) I suddenly get the error message, "Unable to initialize HDV deck. Please make sure a deck is connected and try again."
Any ideas?

Definitely. Shot on HDV, definite difference between the clips I've captured so far (HD capture that worked fine before this is high quality sharp image, where as when capturing in SD, image quality is poor and smaller).
Everything has been filmed on the same camera with no setting changes between shots. Like I said before, I have already been able to capture today in HD just fine, but for some unknown reason (which I don't think is the prefs.) capture will not work. I can 'trick' FCE into HD capture but it gets stuck on cueing tape (even though video is playing fine on camera).

Similar Messages

Unable to initialize HDV deck. Please make sure a deck is connected....

Ok, this is driving me nuts. I've done this before. I have a Canon HV20. I spent HOURS and HOURS on Sunday (two days ago) capturing 1.5 hours of video (DV, not HD) from my HV20 using iMovie09. Then spent more hours burning a DVD using iDVD09. Results were less than glamorous. Quite disappointing, video-quality-wise....
So today I reinstalled FCE 4.0 (HD) and decided to capture a few minutes of the same film and compare the results when making a DVD. My expectations are that it will look better. Naturally, I was hoping for the less-expensive, easier to use product (iMove09) would win, but so far, I can't compare because I keep getting "Unable to initialize HDV deck...". Folks, I have a firewire cable connected. I just used the same camera on the same cable on the same computer (macbook pro). the ONLY thing i changed was the software. Even switched back to iMovie for a minute to see if the cable still worked and sure enough, it's fine.
So, I'm blank on ideas here as to why "FILE/CAPTURE" in FCE would give me this error now. I'm waaaaaaaay open to ideas and even open to "stupid user error"... just tell me what it is....
This is soooooooooooo frustrating. Now I remember why I don't do video that often. Real pain in the butt sometimes...
Thoughts????

"Unable to initialize HDV deck...".
You seem to be trying to capture DV?
At the moment FCE is looking for a HDV camera and there is not one attached, a DV camera is.
Change the Easy Setup to the correct DV option to match the cameras output (audio and video), save, then try again.
Al

"Unable to initialize video deck" inquiry

I am new to Mac and FCE, so I ask for some slack...
I am trying to get video from my Panasonic AG DVX 100 into FCE.
About my system: IMac 2.4 GHz Intel Core 2 Duo with OS X 10.5.2. I have FCE 4 on this computer, not an upgrade of earlier program, but version 4, straight out of the box. I know FCE is working, because I have edited a hour long project on it.
Here's my issue: With the first project complete, I want to import some new video into FCE and start another project. I connect the camera to the Mac via firewire (the white cable that I bought at the Mac store). When I go to "File" in FCE, I go to capture, and I get the following message:
*"Unable to initialize video deck. You may still use capture now."*
I continue by selecting "capture now." The capture window appears with "preview disabled" on the color bars, "no communication" at the bottom of the window. I hit "capture now" in the bottom right and I get the following message:
*"Attempt to capture video without a video device selected. Please select a video device in your capture presets and try again."*
I can't seem to track down "capture presets" , so that's my first issue. This was not a problem the first time I captured video. While at the Mac store, we plugged the camera into other Macs, but still would not get a signal. On FC, it would recognize the camera for a second or two, then flash the "no communication" error. The Mac folks believed it was a camera video out issue.
Some additional factors:
1. it's not the video output on this particular camera. Since that Mac store visit, I hooked it up to another computer and I could see video. So I'm confident that the camera will send video through this firewire.
2. Back to my original project, I imported video into FCE using this cable and a different mini dv camera (sony). It worked with the Sony camera, but will not work with this Panasonic.
I asked another friend, a MAC/FC/Panasonic DVX 100 guy, and he has never encountered this particular error message. He believes it's some setting within the computer that can be fixed through a software patch.
I would be most grateful for insight into solving what is likely a problem others have experienced. Please keep in mind that I am new to this whole process, and will likely show this thread to the people at the Mac store during my next one-on-one class.
Thank you very much.

David:
Thanks for your suggestion. I did check the firewire to ensure it's securely in place, and it seems like it is.
I did connect this camera and this firewire into a friend's macbook, and the signal was successfully received.
So I don't think it's a "loose wire" possibility. We also checked another camera into my Mac's firewire port, and it was successful.
So for some unknown reason, this particular Mac will not recognize this particular camera.
Again, your insights are greatly appreciated.

Unable to initialize video deck

I'm using Final Cut Pro 7.0.2 and I get this message when trying to Capture Footage from my camera: "Unable to initialize video deck". My settings are on Firewire NTSC which is what I always use. I used it a week ago and it worked then and many times before, now all of a sudden, it doesn't work. Anyone know what the problem is? Is the firewire fried or is there something else that could be wrong?

I am having a similar problem. I have the Canon Z65 DV camcorder and have a firewire 800 cable that connects correctly to the camera and my newer Macbook Pro but i dont see anything under the Apple Info under firewire. It just lists the maximum speed for the firewire bus. I put the camera on VCR/Play mode and even tried setting the cameras VCR setting VCR-->DV to On but still i dont see any changes for whats connected to the firewire bus or the ability to see the camera in imovie.
Any advice?

Unable to Intialize HDV deck - can anyone pls help me with this FCE Issue?

I have recently moved from a MacBook Pro (circa 2 yrs old) to a new MacBook Pro with the NEW firewire 800 port. I have bought a new firewire cable and my camera does not want to be capture from my Sony A1E.
I have a MacBook Pro 2.8ghz running on OS X 10.6.2 and have all the updates installed for FCE.
Every time i try to capture the message comes up "Unable to Intialize HDV deck. Please make sure a deck is connected and try again".
The System is set up to receive the correct frame rate footage and type of footage (which is: HDV-Apple Intermediate Codec 1080i50. Formats: All formats). I am running on PAL, so 25fps.
Is there any advice / direction that you could give me at all as I am struggling!
Any help support would be appreciated!
Thanks, Martin

Hi,
Would you confirm that you are using a 9-pin to 4-pin FW cable to connect to your camcorder and that your camcorder is the only FW device connected to your Mac.
When you start up FCE with the camera connected to your Mac and already powered on in VTR mode, does FCE 'see' the camera, or do you get a warning message that FCE is "Unable to locate the following external devices ..." ?

Unable to initialize video deck, (can not capture from camera)

Hello All,
I am using a quad core G5 and am trying to capture some footage into Final Cut Pro version 5.0. I have two Panasonic DVX 100B mini DV cameras. I normally capture with a JVC BR-DV3000 mini DV deck but it is currently not working. So I'm trying to capture using my camera.
I hooked my camera up to my computer via firewire and started final cut, When I click File > Log and capture a little window pops up that reads:
" Unable to initialize video deck. You may still log offline clips or use Capture Now"
I'm not sure why this box is appearing. When I click the capture now button, the Capture window pops up and then I press play on the video camera and the footage plays on the camera but the capture window remains black or empty. I have tried both cameras and two different firewire cables with the same results. I have also tried to restart the computer.
Can anyone shine some light on this situation?
Thank you so much for your help.
Mike Wardynski

Are there any other firewire devices connected to your Mac?
Did you go into your easy setup and reselect the DV setting for the standard you are using?
Also sometimes, shutting down and restarting your Mac, after making these changes some times allows the new device to be recognized.
One other thing, the DV camera may have a menu setting that needs to be set for communication via firewire possibly?

Unable to initialize video deck help

Yesterday my sony dvcam deck that had been working well for around 3 years failed to initialize and I can't get final cut to recognize it. I've tried everything. I trashed the prefs, reinstalled final cut, reinstalled quicktime, deleted the quicktime receipts, different presets etc. and nothing seems to work. I can capture video with imovie and quicktime but final cut won't recognize it. I have nowhere else to turn!
Any help would be appreciated,
Tim

"...When the problem occurred my versions were:
OS - 10.4.11
FCP - 5.1.4
QT - 7.6.2..."
This may have started the issue. FCP 5.1.4 works best with the OS you list, but also QT 7.1.2(or3). Inadvertently upgrading QT above this has been know to bungle FW connectivity.
My guess is that you process of upgrading FCS hasn't cleared the issue.
So, you may be correct, in that...depending on how you accomplished the FCS upgrade, you may need to restart the process.
Since I've not had to do this, I'll let others post details, or search this forum for somethiing like... "FCP doesn't recognize", or some such terminology. We've seen this often in the past.
Best procedure is to do a complete archive/erase/install of all components...OS/FCP/QT, which gets you up to date with best clean combination.
This link may be of assistance regarding best combos...
http://www.digitalrebellion.net/blog/posts/recommendedquicktime_and_mac_os_configurations_for_final_cutpro.html
K
EDIT - just noticed you're on a PPC G5. My understanding is that G5's will not work with Snow Leopard, so be advised...Leopard is as high as you should go with the OS.
Message was edited by: Kevan D. Holdsworth

Unable to Initialize video deck, you may still use capture now. ??

Im trying to capture footage off my sony DCR-TRV900. Ive been able to do it before, but all of a sudden i cant. Ive tried all sorts of crap like switching cables, even sending the camera in. I dont know if settings got messed up or crap like that, but now my FCE is just acting weird with the camera plugged in. If i try to start it with my camera plugged in with VTR on, it will just crash. Ive been using FCE for 2 years now, and i really don't think i changed anything preference-wise. The only MAJOR change to my computer has been leopard, and if that somehow screwed it up, i will be ******. I can capture using a different camera, by putting the tape that i used in my 900 into a DCR TRV9. however, it always fails to capture correctly, screwing up the audio and leaving it un-synced. If someone could help me, it would be a life saver, thanks. Also, i wouldn't consider myself a beginner, but i taught myself how to use this program from the ground up, so i might be missing a crucial step.
Comp specsM
IMAC
Processor Name: Intel Core 2 Duo
Processor Speed: 2.16 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 4 MB
Memory: 2 GB
Message was edited by: alex2928

Let's start over.
I confused myself by invoking the Capture window. Of course that didn't work.
This was a completely different problem. My apologies.
The real problem was that the Log and Transfer window displayed ONLY the Logging pane. The clip list and queue pane were hidden and I couldn't get them back. I eventually found that resizing the entire window - even a small nudge - restored the missing panes. I expected the pane divider bar to not reveal the clip list, but this doesn't happen until the bar gets at least halfway across the window at which point the pane suddenly pops into view. This also confused me.
For the record, I'm using a MacBook core solo running Leopard. My Panasonic SD1 camera is not connected. The files from dozens of camera cards are stored on an external USB drive. I copy selected AVCHD folders from the USB drive to the root directory of the MacBook boot drive so that FCE will recognize them. The scratch disk is a large Firewire 400 drive also connected to the MacBook.

Multiple computers unable to initialize decks.

I have something very odd happening. At the University where I teach we have multiple Macs all running Final Cut. First one PowerPC started giving a message that it was "unable to initialize" the deck. I tried two decks and two cameras... nothing. Now I have three machines all giving me the same message. I brought my Computer and Deck from home (Sony DV Cam) which was working. I plugged it into one of the school's computers and zip. I plugged back into my computer... and now it can't initialize. I've tried two brand new firewires (6 to 4 pin) and neither work.
I've checked all the setting and they are fine.
I have students trying to turn in final projects and I'm stumped.
Does anyone have any suggestions as to what might cause this wide spread failure?
Thanks in advance

I plugged it into one of the school's computers and zip. I plugged back into my computer... and now it can't initialize.< </div>
My first conclusion is that your decks at the school have had their FW ports shorted and this is shorting out and destroying your computers' ports one at a time as each one is attached to the decks.
You bebug this with a simple binary test that will end in a small and relatively inexpensive disaster. If you cannot determine which of the decks (maybe all) have burned out FW ports (might google testing FW, there's probably a simple device for the task), you must locate working FW buses on a computer and then plug in your decks. Buy several cheap FW cards, install them in one machine. Fry them one at a time until you determine where the problem lies.
bogiesan

Unable to initialize capture device and device control in HDV

I shot with a Sony HVR-Z1U/Z1N and am using a Sony HDV 1080i tape deck to digitize.
I recently purchased a MacBook Pro and installed FCP Pro 5 on it. After getting over some time code issues we were chugging along, when on the 4th tape the image on the log and capture screen suddenly dissapeared (I could get audio and could see the image on the tape deck). Well after taking the tape out, checking and rechecking it I popped it back in and ever since then, I have been getting this error mssg "Unable to initialize capture device and device control."
I have tried deleting the preferences and starting from scratch. If I do that, and choose the easy setup with HDV- 1080i60, it gives me this error "Unable to locate the following external devices- HDV (1440 X 1080) 30fps.
I upgraded to FCP 5.1.2 this morning and upgraded the OS to 10.4.7 and QT to 7.1.3 and still no change.
Im at my wits end, Ive been working on this for a whole week now.
Thank you,
Bugs

It has been reported to take more than one attempt to correct the installation but, if properly executed on a machine without other system problems, the QT reinstall process does work. The key element here is you must reinstall QT after you trash the receipts. The process is listed below.
x
To do a full quicktime reinstall.
Go to /library/receipts and delete any files that say Quicktime followed by a number e.g. Quicktime703.pkg
Go to the Apple quicktime site and download the appropriate version of Quicktime to your hard drive.
Run the Quicktime installer.
Repair Disk Permissions for your System Disk (Disk Utility > Select the system disk > Repair Disk Permissions)
Reboot
If this doesn't work, then the problem lies elsewhere:
1. your system - user preferences, firewire ports or other system elements.
2. your equipment - camera/deck/firewire cables.
3. your process - not setting up the software properly or using the software erroneously.
Listed below is a troubleshooting process. Not all steps are appropriate but the general process of isolating the problem is useful.
Troubleshooting Steps for OS X
by Jan Johannsen (Collected from: Apple>User Tips Library>User Tips Contributions forum)
FIRST AID
01 Completely shutdown, wait a 5 minutes, restart
02 Make sure you're not running out of free space on the System volume
03 Check/fix the filesystem using Disk Utility &/or Diskwarrior
04 Repair permissions using Disk Utility
05 Create a new user account, and see if the problem persists there
06 Clear system & user caches
07 Run FCP Rescue
08 Unplug all USB, Firewire devices except Apple mouse
09 Startup in SafeBoot mode, and see if the problem persists there
10 Reset system firmware
MORE SERIOUS TROUBLESHOOTING
11 Reapply the latest combo updater
12 Run the Apple hardware diagnostic CD
13 Check the hard drive for bad blocks
14 Take out 3rd party RAM
15 Unplug 3rd Party PCI cards
16 Reset PMU
17 Archive and reinstall the OS
18 Reinstall the system from scratch
19 Send the machine back to Apple

5.1.4 update breaks HDV capture? Unable to Initialize Capture Device

Problem:
Final Cut Pro cannot capture standard 1080i60 HDV footage from Sony FX1 camcorder. FCP reports "Unable to Initialize Capture Device" when the log and capture window is opened. However, the footage CAN be captured in iMovie (which is interesting, and unacceptable). When HDV>DV downconvert option on camcorder is activated, footage CAN be captured as anamorphic SD, so the camcorder and FW do work.
The problem is occuring on a rock-solid FCP system that I use on a regular basis (mainly for SD editing). It has been approx 2 weeks since I last attempted a HDV capture, the system has been working great with SD footage (still does).
Factors that have changed to my knowledge since HDV capture was last functioning properly:
*Added a new external FW drive into regular usage (a different brand than normally used, no issues with it so far).
*Updated FCP to 5.1.3, and then 5.1.4 when that fix came out. All SD captures and work have been fine so far.
Here's what's interesting...I had a copy of the FCP v5.0.4 .app that I had saved an archive of prior to the crossgrade update. Guess what? I can load it up, and it captures HDV without any problems! With that in mind, this looks like an FCP 5.1.4 issue. But I am at a loss on how to proceed further in troubleshooting. Many thanks in advance for any assistance.
Matt Jeppsen
FresHDV.com
---NOTES---
What I have tried:
*Attempted capture with a different Sony FX1 camcorder.
*Swapped firewire cables and system firewire ports.
*Attempted capture with camera FW chained to an external HDD.
*Unplugged all other external firewire devices from the system.
*Trashed FCP prefs using FCP Rescue 5, created new project using Easy Setup (for HDV).
*Tried different variations of FCP A/V settings, tried all the HDV FW device control presets and the HDV AIC capture preset.
*Per instructions at http://docs.info.apple.com/article.html?artnum=301852 I removed the numbered Quicktime pckg Receipts and re-installed the latest version (7.13). Post-install/reboot, I repaired Disk Prefs and Verified the disk using Disk Util.
*Have also attempted installing QT 7.13 2 and 3 times in a row, also trying disk prefs repair BEFORE the post-install reboot.
Final Cut Pro Audio/Video Settings:
Sequence Preset: HDV-1080i60
Capture Preset: HDV
Device Control Preset: Sony HDV Firewire
Sony HDR-FX1 IN/OUT REC settings:
*VCR HDV/DV: HDV
*COMPONENT: 1080i/480i
*i.LINK CONV: OFF
*TV TYPE: 16:9
*A/V->DV OUT: OFF
System/Software Facts:
*Final Cut Pro 5.1.4
*Quicktime 7.13
*PPC Mac G5 2.7 Dual (2.5GB RAM)
*35GB free on System, 45GB free on internal FCP Scratch disk
Final Cut Pro 5.1.4, G5 DP 2.7 (PPC) Mac OS X (10.4.8)

I think I figured out this vexing problem. I too was having the same issue. Check to see that your Quicktime is newer than 7.1.2. If it isn't you'll have to upgrade it. I only upgraded to 7.1.6 here because I was afraid of going to a really new version. http://www.apple.com/support/downloads/quicktime716formac.html. After I upgraded my quicktime, I ran software update and the Final Cut Pro 5.1.4 update appeared. I hoipe this helps.

Unable to initialize deck?

I have 3 tapes from an event to capture and edit with my Panasonic DVX100B. The first tape captured fine. A couple of days later I try to capture another tape and suddenly I get "unable to initialize deck"!
I have...
1) Tried to capture on my Macbook Pro - same message
2) Tried to capture with a different camera - Canon Optura 40 - when I click capture it says "no video"
3) Deleted QuickTime Receipts and reinstalled QuickTime
4) Tried to capture with QuickTime and iMovie - no can do
5) Tried to change settings in FCP but it says "[Missing] Apple Firewire NTSC
any suggestions? Please help!
Diane

For whatever reason, your mac is not recognizing the deck/camera. Not sure what the issue is, since it obviously recognized the FW drive on at least one port, yet didn't recognize the 2nd camera.
My first thought would be bad FW cable(s)/port(s), but what you've explained doesn't sound like the problem.
FYI, updates are a tricky business...particularly QT. Final Cut tends to operate best with certain combinations of OS/FCP/QT. But that shouldn't explain your mac not even recognizing the camera(s).
Tell us exactly what versions of OS/FCP/QT you're currently working with.
Might also try connecting both cameras to see if they can see each other (ruling out bad FW ports on each). Might also go buy a new FW cable.
Post back,
K

Droid Razr M Camera is unable to initialize problem HELP!!

I have a Droid Razr M and lately when I try to use the camera I get a message saying "camera is unable to initialize". Now this doesn't always appear but when it does I have to reboot my phone if I want to use the camera. As you can imagine this is very frustrating and time consuming especially if you are just trying to snap a candid pic. Does anyone else have this issue or know a fix for it?? Thanks!

I have the same problem with my one year old Razor Max.
I did what was suggested by breezex in #1 (pasted below) but don't know how to system cache clear/cache partition reformat.
Settings > Apps > All > Camera and clear cache and data
A system cache clear/cache partition reformat. Just follow the instructions for an alternate factory reset (using volume and power buttons) and do the cache clear instead of a factory reset. Be careful.
I launched in Safe Mode without success. I went to my local Verizon store and they eventually did a factory reset (wiping out everything). Then the camera worked. That was yesterday, 4/3/13.
Now: same thing all over again, except Safe Mode helps. Camera starts but often freezes on a random image.
This is probably happening a lot more than we see here in this page.
Please HELP Verizon!!!!

Unable to capture HDV in FCP 6.0.1 from Sony HVR-Z1P

Hi I'm attempting to capture HDV footage from a Sony Z1.
I am trying to capture some HDV footage I shot with the Z1, but FCP simply refuses to recognize the Z1
I'm certain I've got all the settings correct:
- Camera is set to HDV firewire out
- capture presets is set to HDV
- device control preset is set to Sony HDV FireWire
- sequence preset is set to HDV 1080i50 (I'm in Australia)
- footage IS HDV 1080i50
But I keep getting the "Unable to Initialize Capture Device and Device Control" popup. I've tried everything
- rebooted the camera
- restarted FCP
- rebooted the system
- changed the capture/device control settings in FCP and tried out a regular DV deck to make sure it wasn't the cable
Nothing has worked.
I'm on a MBPro I7. No Kona card or anything like that, just trying to capture through firewire.
Any suggestions would be greatly appreciated.
Thank you,
Matt
At present it will capture HDV in IMovie but not FCP 6.0.1
Message was edited by: Matt Blyth

Thanks Adrian, since posting the thread I've thought of that too but unfortunately to no avail. From other forums I've read this seems to be a central theme to the solution to my capture woes. I since have sorted the problem it was in Audio/Video Settings.
In the end I set my Audio/Video Settings to:
Sequence Preset to: Apple Intermediate Codec 1080i50
Capture Pre-HDV- Apple intermediate Codec
Device Control Preset: Sony HDV 1080i50 Firewire
And hey presto my I'm capturing HD without any problems. Thanks everyone for your suggestions.
Message was edited by: Matt Blyth

Unable to Initialize Capture Device

Hi,
I am having a problem importing/capturing HDV video from my JVC HD GR 1 getting "Unable to Initialize Capture Device".
I have been able to capture fine up to this point, finicky some times to be sure, but workable, then in the last few weeks it began getting more and more finicky (wouldn't connect to camera, restart and it works fine), until just the other day it wont connect no matter what I do!
Help?
Ask questions if you need clarification.
Camera: JVC HD GR 1
Tape: Mini DV
Format: HDV
Software: FCP 5.1.4

Unfortunately when both "Capture" and "Device Control" presets are not set to HDV it wont even try to connect and gives me this warning:
"To capture HDV source material, both the Capture and Device Control presets must be configured for HDV; otherwise, to capture in another format, both must not be configured for HDV."
As a side note when my camera was connecting to FCP. FCP would only give me on screen controls half the time.

Unable to initialize hdv deck problem

Similar Messages

Maybe you are looking for