Unable to initialize IMAQ1394 in Labview

I have a new problem. This used to work OK. I get the attached error when trying to initialize my camera using Labview. I can use MAX without a problem, and a previously built executable works. An executable that I just built gives the same error, though. I have uninstalled and reinstalled NI-IMAQ for IEEE 1394 Cameras, but it did not help. Any ideas?
Attachments:
IMAQ1394 Error.doc ‏25 KB

Hi Brian,
Can you run Snap.vi (example program that ships with the 1394
driver)? If Snap.vi will run then we know that the driver and
LabVIEW are not corrupt and the problem lies with the source VI you are
using to make your .exe. If Snap.vi will not run then it must be
a corruption of the driver or LabVIEW. You indicated that you had
reinstalled the driver. Did you uninstall the driver first?
If not, then uninstall the driver and reinstall. There is a
possibility that the call library node primitive could be corrupt
(located in the IMAQ 1394 init.vi). If this is the case we might
have to uninstall/reinstall LabVIEW but I would like to do this as a
last resort. Test the functionality of the call library node
first. You can do this very easily if you have any other NI
hardware that you are controlling through LabVIEW. Typically the
API will use a call library node to make a call to the driver
.dll. This is what's happening with the IMAQ 1394 init.vi.
If you can control other NI hardware through LabVIEW then we know that
the call library nodes are working properly. If none of these
suggestions help you find the source of the problem, please post your
simplified VI and I will take a look at it.
Regards,
Brooks W.
National Instruments

Similar Messages

Unable to initialize the VISA library

/usr/local/vxipnp/linux/NIvisa/NIvisaic --> Unable to initialize the VISA library. The VISA Interactive Control utility will exit.
Running RHEL 5.11 (32-bit)
[root@x74943 ~]# rpm -qa|grep nivisa
nivisa-4.5.1-f0
[root@x74943 ~]# rpm -qa|grep ni488
ni4882i-2.5.1-f0
gpibexplorer and driverwizard start up fine. I've never used nispy, but it is bombing too.
x74943(paul.autore)8> ./nispy
LabVIEW caught fatal signal
8.2.1 - Received SIGSEGV
Reason: address not mapped to object
Attempt to reference address: 0x10
Segmentation fault
Uninstall and re-install of NI-VISA didn't help. NIvisaic was running fine days ago. This system was not patched since it was working OK, but the root partition was reduced and a new physical volume was created for LVM so that /var, /tmp,... could be copied over and remounted as separate file systems.
I have not tried yet to mess with reinstalling NI-488.2
ldd /usr/local/vxipnp/linux/NIvisa/NIvisaic shows same output as an identical working system

This issue has been resolved. It may have been the re-install of NI-488 that really solved the problem. The ‘gpibprtk.ko’ module had a problem loading, but we also found a problem with a shared memory kernel parameter.

Error while installing exchange2007 : Unable to initialize the Microsoft Exchange Information Store service. Failed to find the

Hi,
I am trying fresh install of exchange2007, everything gone well but, finally it thrown a error saying :
Unable to initialize the Microsoft Exchange Information Store service. Failed to find the working directory parameter from the registry - Error 0x80004005.
the installation log says
6/5/2007 3:14:05 PM] [1] Processing component 'Mailbox Service Control (Last)' (Starting mailbox services).
[6/5/2007 3:14:05 PM] [1] Executing 'start-SetupService -ServiceName MSExchangeIS -MaximumWaitTime "unlimited"', handleError = False
[6/5/2007 3:14:05 PM] [2] Launching sub-task '$error.Clear(); start-SetupService -ServiceName MSExchangeIS -MaximumWaitTime "unlimited"'.
[6/5/2007 3:14:05 PM] [2] Beginning processing.
[6/5/2007 3:14:05 PM] [2] The maximum wait for the operation is set to 'unlimited'.
[6/5/2007 3:14:05 PM] [2] Service checkpoint has progressed. Previous checkpoint='0' - Current checkpoint='1'.
[6/5/2007 3:14:05 PM] [2] Will wait '10000' milliseconds for the service 'MSExchangeIS' to reach status 'Running'.
[6/5/2007 3:14:15 PM] [2] Service 'MSExchangeIS' failed to reach status 'Running' on this server after waiting for '10000' milliseconds.
[6/5/2007 3:14:15 PM] [2] Service 'MSExchangeIS' failed to start. Check the event log for possible reasons for the service start failure.
[6/5/2007 3:14:15 PM] [2] [ERROR] Unexpected Error
[6/5/2007 3:14:15 PM] [2] [ERROR] Service 'MSExchangeIS' failed to start. Check the event log for possible reasons for the service start failure.
[6/5/2007 3:14:15 PM] [2] Ending processing.
[6/5/2007 3:14:15 PM] [1] The following 1 error(s) occurred during task execution:
[6/5/2007 3:14:15 PM] [1] 0. ErrorRecord: Service 'MSExchangeIS' failed to start. Check the event log for possible reasons for the service start failure.
[6/5/2007 3:14:15 PM] [1] 0. ErrorRecord: Microsoft.Exchange.Configuration.Tasks.ServiceFailedToStartException: Service 'MSExchangeIS' failed to start. Check the event log for possible reasons for the service start failure.
[6/5/2007 3:14:15 PM] [1] [ERROR] Service 'MSExchangeIS' failed to start. Check the event log for possible reasons for the service start failure.
[6/5/2007 3:14:15 PM] [1] Setup is halting task execution because of one or more errors in a critical task.
[6/5/2007 3:14:15 PM] [1] Finished executing component tasks.
[6/5/2007 3:14:15 PM] [1] Ending processing.
[6/5/2007 3:14:18 PM] [0] End of Setup
[6/5/2007 3:14:18 PM] [0] **********************************************
this I am trying on my test system please help me out in resolving the issue
thanks in advance,

Gary,
Open Registry Editor.
In Registry Editor, navigate to the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\MSExchangeIS\ParametersSystem
Create the following value (REG_SZ): Working Directory and give it a value that points to the new database folder.
Make sure you back up the registry before you do any changes on it.
Raj

5.1.4 update breaks HDV capture? Unable to Initialize Capture Device

Problem:
Final Cut Pro cannot capture standard 1080i60 HDV footage from Sony FX1 camcorder. FCP reports "Unable to Initialize Capture Device" when the log and capture window is opened. However, the footage CAN be captured in iMovie (which is interesting, and unacceptable). When HDV>DV downconvert option on camcorder is activated, footage CAN be captured as anamorphic SD, so the camcorder and FW do work.
The problem is occuring on a rock-solid FCP system that I use on a regular basis (mainly for SD editing). It has been approx 2 weeks since I last attempted a HDV capture, the system has been working great with SD footage (still does).
Factors that have changed to my knowledge since HDV capture was last functioning properly:
*Added a new external FW drive into regular usage (a different brand than normally used, no issues with it so far).
*Updated FCP to 5.1.3, and then 5.1.4 when that fix came out. All SD captures and work have been fine so far.
Here's what's interesting...I had a copy of the FCP v5.0.4 .app that I had saved an archive of prior to the crossgrade update. Guess what? I can load it up, and it captures HDV without any problems! With that in mind, this looks like an FCP 5.1.4 issue. But I am at a loss on how to proceed further in troubleshooting. Many thanks in advance for any assistance.
Matt Jeppsen
FresHDV.com
---NOTES---
What I have tried:
*Attempted capture with a different Sony FX1 camcorder.
*Swapped firewire cables and system firewire ports.
*Attempted capture with camera FW chained to an external HDD.
*Unplugged all other external firewire devices from the system.
*Trashed FCP prefs using FCP Rescue 5, created new project using Easy Setup (for HDV).
*Tried different variations of FCP A/V settings, tried all the HDV FW device control presets and the HDV AIC capture preset.
*Per instructions at http://docs.info.apple.com/article.html?artnum=301852 I removed the numbered Quicktime pckg Receipts and re-installed the latest version (7.13). Post-install/reboot, I repaired Disk Prefs and Verified the disk using Disk Util.
*Have also attempted installing QT 7.13 2 and 3 times in a row, also trying disk prefs repair BEFORE the post-install reboot.
Final Cut Pro Audio/Video Settings:
Sequence Preset: HDV-1080i60
Capture Preset: HDV
Device Control Preset: Sony HDV Firewire
Sony HDR-FX1 IN/OUT REC settings:
*VCR HDV/DV: HDV
*COMPONENT: 1080i/480i
*i.LINK CONV: OFF
*TV TYPE: 16:9
*A/V->DV OUT: OFF
System/Software Facts:
*Final Cut Pro 5.1.4
*Quicktime 7.13
*PPC Mac G5 2.7 Dual (2.5GB RAM)
*35GB free on System, 45GB free on internal FCP Scratch disk
Final Cut Pro 5.1.4, G5 DP 2.7 (PPC) Mac OS X (10.4.8)

I think I figured out this vexing problem. I too was having the same issue. Check to see that your Quicktime is newer than 7.1.2. If it isn't you'll have to upgrade it. I only upgraded to 7.1.6 here because I was afraid of going to a really new version. http://www.apple.com/support/downloads/quicktime716formac.html. After I upgraded my quicktime, I ran software update and the Final Cut Pro 5.1.4 update appeared. I hoipe this helps.

Unable to initialize HDV deck. Please make sure a deck is connected....

Ok, this is driving me nuts. I've done this before. I have a Canon HV20. I spent HOURS and HOURS on Sunday (two days ago) capturing 1.5 hours of video (DV, not HD) from my HV20 using iMovie09. Then spent more hours burning a DVD using iDVD09. Results were less than glamorous. Quite disappointing, video-quality-wise....
So today I reinstalled FCE 4.0 (HD) and decided to capture a few minutes of the same film and compare the results when making a DVD. My expectations are that it will look better. Naturally, I was hoping for the less-expensive, easier to use product (iMove09) would win, but so far, I can't compare because I keep getting "Unable to initialize HDV deck...". Folks, I have a firewire cable connected. I just used the same camera on the same cable on the same computer (macbook pro). the ONLY thing i changed was the software. Even switched back to iMovie for a minute to see if the cable still worked and sure enough, it's fine.
So, I'm blank on ideas here as to why "FILE/CAPTURE" in FCE would give me this error now. I'm waaaaaaaay open to ideas and even open to "stupid user error"... just tell me what it is....
This is soooooooooooo frustrating. Now I remember why I don't do video that often. Real pain in the butt sometimes...
Thoughts????

"Unable to initialize HDV deck...".
You seem to be trying to capture DV?
At the moment FCE is looking for a HDV camera and there is not one attached, a DV camera is.
Change the Easy Setup to the correct DV option to match the cameras output (audio and video), save, then try again.
Al

Unable to initialize hdv deck problem

Hi all,
I'm having the 'unable to initialize hdv deck' problem. I am trying to capture HD footage from a Sony HVR-A1E camera. iLink and down conversion are off (like they should be) and I have just captured a HD tape before the problem started.
I don't understand how I could capture HD footage just fine and then without touching any settings (just trying to start capture again) I suddenly get the error message, "Unable to initialize HDV deck. Please make sure a deck is connected and try again."
Any ideas?

Definitely. Shot on HDV, definite difference between the clips I've captured so far (HD capture that worked fine before this is high quality sharp image, where as when capturing in SD, image quality is poor and smaller).
Everything has been filmed on the same camera with no setting changes between shots. Like I said before, I have already been able to capture today in HD just fine, but for some unknown reason (which I don't think is the prefs.) capture will not work. I can 'trick' FCE into HD capture but it gets stuck on cueing tape (even though video is playing fine on camera).

Unable to Initialize Capture Device

Hi,
I am having a problem importing/capturing HDV video from my JVC HD GR 1 getting "Unable to Initialize Capture Device".
I have been able to capture fine up to this point, finicky some times to be sure, but workable, then in the last few weeks it began getting more and more finicky (wouldn't connect to camera, restart and it works fine), until just the other day it wont connect no matter what I do!
Help?
Ask questions if you need clarification.
Camera: JVC HD GR 1
Tape: Mini DV
Format: HDV
Software: FCP 5.1.4

Unfortunately when both "Capture" and "Device Control" presets are not set to HDV it wont even try to connect and gives me this warning:
"To capture HDV source material, both the Capture and Device Control presets must be configured for HDV; otherwise, to capture in another format, both must not be configured for HDV."
As a side note when my camera was connecting to FCP. FCP would only give me on screen controls half the time.

Unable to initialize capture device and device control in HDV

I shot with a Sony HVR-Z1U/Z1N and am using a Sony HDV 1080i tape deck to digitize.
I recently purchased a MacBook Pro and installed FCP Pro 5 on it. After getting over some time code issues we were chugging along, when on the 4th tape the image on the log and capture screen suddenly dissapeared (I could get audio and could see the image on the tape deck). Well after taking the tape out, checking and rechecking it I popped it back in and ever since then, I have been getting this error mssg "Unable to initialize capture device and device control."
I have tried deleting the preferences and starting from scratch. If I do that, and choose the easy setup with HDV- 1080i60, it gives me this error "Unable to locate the following external devices- HDV (1440 X 1080) 30fps.
I upgraded to FCP 5.1.2 this morning and upgraded the OS to 10.4.7 and QT to 7.1.3 and still no change.
Im at my wits end, Ive been working on this for a whole week now.
Thank you,
Bugs

It has been reported to take more than one attempt to correct the installation but, if properly executed on a machine without other system problems, the QT reinstall process does work. The key element here is you must reinstall QT after you trash the receipts. The process is listed below.
x
To do a full quicktime reinstall.
Go to /library/receipts and delete any files that say Quicktime followed by a number e.g. Quicktime703.pkg
Go to the Apple quicktime site and download the appropriate version of Quicktime to your hard drive.
Run the Quicktime installer.
Repair Disk Permissions for your System Disk (Disk Utility > Select the system disk > Repair Disk Permissions)
Reboot
If this doesn't work, then the problem lies elsewhere:
1. your system - user preferences, firewire ports or other system elements.
2. your equipment - camera/deck/firewire cables.
3. your process - not setting up the software properly or using the software erroneously.
Listed below is a troubleshooting process. Not all steps are appropriate but the general process of isolating the problem is useful.
Troubleshooting Steps for OS X
by Jan Johannsen (Collected from: Apple>User Tips Library>User Tips Contributions forum)
FIRST AID
01 Completely shutdown, wait a 5 minutes, restart
02 Make sure you're not running out of free space on the System volume
03 Check/fix the filesystem using Disk Utility &/or Diskwarrior
04 Repair permissions using Disk Utility
05 Create a new user account, and see if the problem persists there
06 Clear system & user caches
07 Run FCP Rescue
08 Unplug all USB, Firewire devices except Apple mouse
09 Startup in SafeBoot mode, and see if the problem persists there
10 Reset system firmware
MORE SERIOUS TROUBLESHOOTING
11 Reapply the latest combo updater
12 Run the Apple hardware diagnostic CD
13 Check the hard drive for bad blocks
14 Take out 3rd party RAM
15 Unplug 3rd Party PCI cards
16 Reset PMU
17 Archive and reinstall the OS
18 Reinstall the system from scratch
19 Send the machine back to Apple

"Unable to initialize video deck" inquiry

I am new to Mac and FCE, so I ask for some slack...
I am trying to get video from my Panasonic AG DVX 100 into FCE.
About my system: IMac 2.4 GHz Intel Core 2 Duo with OS X 10.5.2. I have FCE 4 on this computer, not an upgrade of earlier program, but version 4, straight out of the box. I know FCE is working, because I have edited a hour long project on it.
Here's my issue: With the first project complete, I want to import some new video into FCE and start another project. I connect the camera to the Mac via firewire (the white cable that I bought at the Mac store). When I go to "File" in FCE, I go to capture, and I get the following message:
*"Unable to initialize video deck. You may still use capture now."*
I continue by selecting "capture now." The capture window appears with "preview disabled" on the color bars, "no communication" at the bottom of the window. I hit "capture now" in the bottom right and I get the following message:
*"Attempt to capture video without a video device selected. Please select a video device in your capture presets and try again."*
I can't seem to track down "capture presets" , so that's my first issue. This was not a problem the first time I captured video. While at the Mac store, we plugged the camera into other Macs, but still would not get a signal. On FC, it would recognize the camera for a second or two, then flash the "no communication" error. The Mac folks believed it was a camera video out issue.
Some additional factors:
1. it's not the video output on this particular camera. Since that Mac store visit, I hooked it up to another computer and I could see video. So I'm confident that the camera will send video through this firewire.
2. Back to my original project, I imported video into FCE using this cable and a different mini dv camera (sony). It worked with the Sony camera, but will not work with this Panasonic.
I asked another friend, a MAC/FC/Panasonic DVX 100 guy, and he has never encountered this particular error message. He believes it's some setting within the computer that can be fixed through a software patch.
I would be most grateful for insight into solving what is likely a problem others have experienced. Please keep in mind that I am new to this whole process, and will likely show this thread to the people at the Mac store during my next one-on-one class.
Thank you very much.

David:
Thanks for your suggestion. I did check the firewire to ensure it's securely in place, and it seems like it is.
I did connect this camera and this firewire into a friend's macbook, and the signal was successfully received.
So I don't think it's a "loose wire" possibility. We also checked another camera into my Mac's firewire port, and it was successful.
So for some unknown reason, this particular Mac will not recognize this particular camera.
Again, your insights are greatly appreciated.

Unable to initialize video deck

I'm using Final Cut Pro 7.0.2 and I get this message when trying to Capture Footage from my camera: "Unable to initialize video deck". My settings are on Firewire NTSC which is what I always use. I used it a week ago and it worked then and many times before, now all of a sudden, it doesn't work. Anyone know what the problem is? Is the firewire fried or is there something else that could be wrong?

I am having a similar problem. I have the Canon Z65 DV camcorder and have a firewire 800 cable that connects correctly to the camera and my newer Macbook Pro but i dont see anything under the Apple Info under firewire. It just lists the maximum speed for the firewire bus. I put the camera on VCR/Play mode and even tried setting the cameras VCR setting VCR-->DV to On but still i dont see any changes for whats connected to the firewire bus or the ability to see the camera in imovie.
Any advice?

Unable to initialize video deck, (can not capture from camera)

Hello All,
I am using a quad core G5 and am trying to capture some footage into Final Cut Pro version 5.0. I have two Panasonic DVX 100B mini DV cameras. I normally capture with a JVC BR-DV3000 mini DV deck but it is currently not working. So I'm trying to capture using my camera.
I hooked my camera up to my computer via firewire and started final cut, When I click File > Log and capture a little window pops up that reads:
" Unable to initialize video deck. You may still log offline clips or use Capture Now"
I'm not sure why this box is appearing. When I click the capture now button, the Capture window pops up and then I press play on the video camera and the footage plays on the camera but the capture window remains black or empty. I have tried both cameras and two different firewire cables with the same results. I have also tried to restart the computer.
Can anyone shine some light on this situation?
Thank you so much for your help.
Mike Wardynski

Are there any other firewire devices connected to your Mac?
Did you go into your easy setup and reselect the DV setting for the standard you are using?
Also sometimes, shutting down and restarting your Mac, after making these changes some times allows the new device to be recognized.
One other thing, the DV camera may have a menu setting that needs to be set for communication via firewire possibly?

Unable to initialize deck?

I have 3 tapes from an event to capture and edit with my Panasonic DVX100B. The first tape captured fine. A couple of days later I try to capture another tape and suddenly I get "unable to initialize deck"!
I have...
1) Tried to capture on my Macbook Pro - same message
2) Tried to capture with a different camera - Canon Optura 40 - when I click capture it says "no video"
3) Deleted QuickTime Receipts and reinstalled QuickTime
4) Tried to capture with QuickTime and iMovie - no can do
5) Tried to change settings in FCP but it says "[Missing] Apple Firewire NTSC
any suggestions? Please help!
Diane

For whatever reason, your mac is not recognizing the deck/camera. Not sure what the issue is, since it obviously recognized the FW drive on at least one port, yet didn't recognize the 2nd camera.
My first thought would be bad FW cable(s)/port(s), but what you've explained doesn't sound like the problem.
FYI, updates are a tricky business...particularly QT. Final Cut tends to operate best with certain combinations of OS/FCP/QT. But that shouldn't explain your mac not even recognizing the camera(s).
Tell us exactly what versions of OS/FCP/QT you're currently working with.
Might also try connecting both cameras to see if they can see each other (ruling out bad FW ports on each). Might also go buy a new FW cable.
Post back,
K

UNABLE TO LOCATE THE THE LABVIEW RUN-TIME ENGINE.LVBROKERAUX71

UNABLE TO LOCATE THE THE LABVIEW RUN-TIME ENGINE.LVBROKERAUX71 REQUIRES A VERSION 7.1 (OR COMPATIBLE) LABVIEW RUN-TIME ENGINE。PLEASE CONTACT THE VENDOR OF LVBROKERAUX71 TO CORRECT THIS PROBLEM
Uninstalled DAQ and reinstalled. MAX still throws an error.
Any Isead besides uninstalling 3/4 of my software?
Merry Christmas!
Matthew Fitzsimons
Certified LabVIEW Architect
LabVIEW 6.1 ... 2013, LVOOP, GOOP, TestStand, DAQ, and Vison

To clean up your system, you will need to uninstall the LabVIEW 7.1 run-time engine, and the "LVBroker," and the "LVBrokerAux71" components using the MSI Blast utility. To obtain this utility, please create a service request for phone or e-mail support, and contact one of our Applications Engineers about this issue. Thank you!

"Unable to open a virtual memory file" and "Unable to initialize Photoshop" errors

Hi
I installed Photoshop CS6 64-bit on Windows 7 SP1 64-bit.
When it starts, these two messages are displayed:
Unable to open a virtual memory file because the file is locked. You do not have permission or the file is being used by another program. ...
Unable to initialize Photoshop because the file is locked. You do not have permission or the file is being used by another program. ...
How come?
Thanks
Bye

In other words, I have installed Photoshop CS6 64-bit (using the default directory) on Windows 7 SP1 64-bit.
My computer has 4 GB of RAM and a virtual memory file of 6644 MB.
When it starts, the two above messages are displayed also with an account of Administrator type?
How come?
Thanks
Bye

Oracle ODBC - Internal Error - unable to initialize NLS during driver load

I'm having some trouble with my ODBC connections which I hope someone can please help me with!
About 6 weeks ago all was working as normal.
As far as I know there have been no updates to the ORacle DB, the Windows XP operating system or the ODBC Drivers.
Today when I opened access and visual case 2 to connect to Oracle I was at first greeted with a:
unable to connect SQLState=IM004 SQL_HANDLE_ENV
error. ODBC also kept crashing.
I restarted the computer and was confronted with a different error:
odbc SQLSTate 08004 ORA 12154 TNS could not resolve the connect identifier specified
I was able to fix this error by setting the environment variable TNS_ADMIN in windows xp environment variables. I'm extremely confused about how this happened though as it was working and I don't think anything has changed.
I was then able to connect to the database via Microsoft Access but when I opened Visual Case 2 and tried to make an update, I was confronted with the following error:
Oracle ODBC Driver - internal error - unable to initialize NLS during driver load
I looked in the registry at:
HKEY_LOCAL_MACHINE\SOFTWARE\Oracle\KEY_OraClient10g_home1
HKEY_LOCAL_MACHINE\SOFTWARE\Oracle\KEY_OraClient10g_home2
HKEY_LOCAL_MACHINE\SOFTWARE\Oracle\KEY_OraDb10g_home1
and NLS_LANG was set to "AMERICAN_AMERICA.WE8MSWIN1252" in all 3 places.
(Though KEY_OraClient10g_home2 only had 4 entries as opposed to KEY_OraClient10g_home1's 13 entries)...
Since I made those changes I can no longer connect through Access.
I just receive a ODBC - connection to 'xxx' failed
Advice greatly appreciated!!!!
Edited by: user11150264 on Aug 25, 2009 10:21 PM

Actually it sort of does...
I switched the ODBC connection to use instant client and now it's all working again.
The biggest mystery is what changed to make it suddenly stop working the old way...

Unable to initialize IMAQ1394 in Labview

Similar Messages

Maybe you are looking for