Unable to Inport Measurement points and Measure documents from R/3 to clien
Hi,
I am not able to import measuring points and measuring documents into the client device even after assigning the measurement point varaint in the back-end config.
Please help!
Thanks & Regards,
Kanwar
Hello Kanwar,
I am thinking of two reasons at the moment.
1. The equipments/Functional location which you had downloaded to your device were not having measurement points. If this is the case, you need to make sure that corresponding Equip/FL's are there on client (provided case 2 is not valid)
2. The measurement points were not replicated. Hope you had checked MEREP_207 table for the required measurement points.
Hope this helps.
Best Regards,
Subhakanth
Similar Messages
-
What is Make System Settings for Measuring Points and Measurement Documents
Dear PM Guru's,
i have doubht on the above customization section? in which situations we can activate or create new one ? whats its importance, how its impacts on our business scenarios. please suggest me and help me. Now i am in realization phase i am not observed much more difference with this check box .
i hope i will get the answer very soonly, and thanks to all of the PM gurusHi,
<< Moderator message - Cut and paste response from http://www.consolut.com/en/s/sap-ides-access/d/s/doc/YY-OLI0IMRCCUST removed. Plagiarism is not allowed in SCN >>
Regrds
Jitender
Edited by: Rob Burbank on Jun 6, 2011 10:53 AM -
Measuring point,counter & meas document
What is the concept of Measuring point,counter & meas document in regard to PM ?
Hi,
Measuring Points are measurement of physical condition like temprature pressure, and consumption like fuel, and reading like hour meter , speedometer etc.
measuring points just like as log book of equipment
it is created by ik01, against technical object with characterstics of which we want to take measurment reading
and when actual reading are recorded against measuring point , a document is genrated called measurment document
it is crated by ik11, ik14 , ik34 against measuring point
regards
Jitender Suhag -
Removing of the Measuring point and superior equipment
Hi,
Can any one tell me the steps to followed for removing and setting og deletion flag for measuring point and superior equipment.
I ran thr Tcode IK05 and deactivated it is it sufficient to do so.please help me.
Regards,
Yashwanthhi
why you want to deactivate the measuring point ,if you have created a maintenance plan you can deactivate the maintenance plan so that system will not generate the maintenance call object.
or it is better you deactivate the equipment itself if you have done that you cannot able to enter further measurement documents for measuring point
regards
thyagarajan -
Hi all,
Can anyone please tell me the process of how to use measuring points and counters and in which scenario it will be used in plant.It would be great if anyone can tell the process with an example and also how to create measuring points and counters iin SAP as well.
Thanks in advance.
Regards,
VijayMeasuring points are physical and/or logical locations at which a particular condition
is described - for example, the temperature of coolant in a nuclear power station
after an outflow from the pressure vessels, or the number of rotations per minute of
the rotary blades of a wind-driven power station. Measuring points are located at
technical objects.
Counters are resources that enable you to represent the wear and tear of an object or
the consumption or reduction in its useful life - for example, the mileage indicator of a
motor vehicle or the electricity consumption meter of an electrically-powered system.
Counters are located at technical objects.
You can enter measurement or counter readings for each object to be maintained. This
makes sense if you want to document the condition of an object based on measurement
readings or if the regular maintenance of an object depends on its meter readings.
You can also check these links:
http://www.sap-img.com/plant/recording-measuring-docs-against-work-orders.htm
http://www.sap-img.com/plant/measuring-points-questions-in-sap-pm.htm -
Measuring point and characteristics
what are the measuring points and characteristics to be created for the thermal power station , sap plant maintenance
Hi,
Its based on the equipments in Power Station & Parameters to be measured for the Equipments. For example, for Boiler, Temperature, Pressure, Water Level, etc., will be measured.
So here we need to create Characteristics for all these. For Boilers, Measuring points will be created for these characteristics.
Equipments under Thermal Power stations could be Boilers, Transformers, Electric Generators, Coal Turbines, Condensers, etc., For each equipment, there will be different critical parameters to be measured on periodical basis.
Create Measuring points for all of them.
Regards,
Maheswaran. -
Equipment Efficiency through Measuring Point and Counters
Hi gurus,
I am planning to get the efficiency of equipment by using Meauring points and counters.
Against an Equipment I have created a Measuring point as counter.
I am capturing Actual output of the machine as mesurment reading.
In order to set the Target output i dont find a solution.
I am expecting from all you guys to give me some solution to set the Expected or standard output against an equipment.
so that i can compare the target vs actual as well as efficiency.The purpose of measuring points and counters is to genrate call objects at given overflow reading or points I dont think so that they can help in calculating the effiency in a way that this machine perfomence is let say 80% and other one is 70%.
However you can maintain it manualy while entering the measuring points in format of % .
Regards
Iftikhar -
Diffrence between Measuring point and Counter
What is the difference between Measuring Point and Counter ?
-MdHi,
_Measuring Point_
Measuring points in the SAP System describe the physical locations at which a condition is described, (for example, Temparature and Pressure on a Boiler ). The characteristics associated with the measuring points which record the value can only be numeric characteristic. Measuring points are located on technical objects, in other words, on pieces of equipment or functional locations. For every measuring point there should be some characteristics to measure the reading.
To enable you to differentiate more easily between the individual measuring points and provide them with a unit, you assign each measuring point to a characteristic.
The parameters like Running Hours, Temperature, Pressure etc,, on equipments can also be mapped under measuring point.
Counter:
A type of measuring point, where a continuous reading is recorded (e.g. Milometer). In case the measuring point is a counter, it needs to be defined likewise.
Counter readings are taken at counters at particular intervals and in particular measurement units.
For Example, counter readings for kilometers driven or electricity used
Regards,
Krishna Mohan. -
Functional location in Measuring Point and while creating M.plan or differe
Hi,
we found that functional location in Measuring point and M.plan functional location Measuring point are differrent, how to restrict that one ,we need automatically flow of functional location from measuring point to Maintenance plan.
--GaneshHi,
If you created the Measuring Point for the selected FL, then that measuring point will be populated automatically. If you have more than one measuring point, then you can select using Possible entries option.
In this case, I think its not possible to restrict with configuration.
IPRM0004 Maintenance plan / item: Customer check for time "SAVE"
Use this user exit, while saving check for the functional location for the selected measuring point & give error message.
Use tables IMPTT to get Object Number of FL. Use IFLOT to get the FL.
Regards,
Maheswaran. -
Graph of Measurement points and a charecteristic vs time
Hi SAP Masters,
I am currently having a problem and I hope you can help me to solve this. I am trying to create a graph where I can compare one of my Design data which is in my characteristic against the graph that i can generate from the measurement point vs time graph.
How can I add the characteristic into this graph?
And How does SAP know that which two column should be used for the graph? I know It can add a secondary y-axix but doesn't allow me to chose any data for that axis.
My objective is to compare the measurement point data(movement) vs time with the design data(design movement). I can generate a column graph of movement vs time from the measurement points and I can display it over last couple of years. but if I can show design movement along with the measurement point movement then it is good for us to see if it is more than design movement stored in the classification tab of the Floc.
thank you
Edited by: sam1188 on Mar 16, 2011 2:24 AM
Edited by: sam1188 on Mar 16, 2011 1:48 PMIf you've been charged twice for the purchase (you didn't click on 'buy' twice and it appears twice on your purhcase history ?) then try the 'report a problem' page to contact iTunes Support : http://reportaproblem.apple.com
If the 'report a problem' link doesn't work then you can try contacting iTunes support via this page : http://www.apple.com/support/itunes/contact/- click on Contact iTunes Store Support on the right-hand side of the page, then Purchases, Billing & Redemption -
Recording measured voltage and current values from LCR 4284A
Hello,
I want to use the labview VI to record the measured voltage and current values from LCR 4284A. These are shown as Vm and Im on the instrument screen. Is it possible to record these values using a VI?
I have looked through the drivers that are available through the "Instrument driver network" (Link) for 4284A but none of the VIs give any option to monitor Vm and Im. If you know how this can be done then I would really appreciate a reply.
Thanks
MansoorI haven't used the instrument but there are functions to enable/read voltage level and current level monitors. Are those different than what you are asking for? What does the manual say about Vm and Im and programatically getting them? If you can find the command in the manual, you can just open the VI Tree and do a text search for the command.
-
HT204053 how do i move page and numbers documents from one icloud login to another?
how do i move page and numbers documents from one icloud login to another?
I had to change my email address whcih meant new apple login.
I have a number of docs in iwork/pages and iwork/numbers. How do I transfer them to my new login?There's a couple of ways but my tip backing up your documents in the cloud is as good as any.
-
How to upload and share document from pages
how to upload and share document from pages app?
Hello dannafromfl,
Documents can be shared via File Sharing to iTunes or via Email.
Pages for iOS (iPad): Send and receive documents in email messages
http://support.apple.com/kb/PH3564
Pages for iOS (iPhone, iPod touch): Share documents by connecting to your computer
http://support.apple.com/kb/PH3598
Cheers,
Allen -
Process blocked sales and distribution documents from the SAPoffice inbox
Hi,
I know VKM1/VKM3 can be used to release order.
And SAP help shows we can process blocked sales and distribution documents from the SAPoffice inbox. Could anyone tell me how?
I can use output type KRML to send a mail to SAPoffice inbox, but don't know how to release blocked sales orders in the SAPoffice inbox.
Many Thanks
JeanHello Jean,
Release the blocked document directly via mail received:
- After carry out the step 4 in note 677377, you will be able to
release the blocked document directly by:
Display the SAP office mail recieved;
Menu: Document -> Execute;
Then you will be redirected to transaction vkm3, with the blocked
document number defaulted on that screen;
Unfortunately, it is not possible to direct your mails to Outlook
and release the document from VKM3.
Best regards,
Lela -
Read parked and posting document from one FM
Hi all,
IS theere any FM avaliable to read parked and posting document from one function module.
Please let me know if anything is there.
ThanksHi T,
have u searched in SE37 with words park?,i'm sure we have few FMs which will do the same.
regards
Prabhu
Maybe you are looking for
-
Lightroom 4-How to reorganize files by date when choosing to add rather than copy them to Lightroom
My photos were in disorganized folders on different hard drives. I was able to import them into Lightroom 4 using COPY, and now my folders are reorganized by year and month on my hard drive, which is how I want them. However, I now have a copy of my
-
Two LOVs in same report customization form causes problems
My report includes two parameters which are set by the user using dynamic LOVs in the customization form. The report used to only have one parameter and this worked fine. After including the second one only one of the LOVs work as they should. The se
-
Despues de la ultima actualizacion de iTunes, sale el siguiente mensaje "the program can't start because MSVCR80.dll is missing from your computer. Try reinstalling the program to fix this problem". Al dar clic en OK sale oro mensaje:"Itunes was not
-
Passing Source Query Variables to Target query in RRI
Hello, I Creating Jump Queries. In the source query user is entering some variable(Dates), based on these varaibles I am creating formula variable in the source query. I wanted pass the same varible values(which are entered by user) to target values(
-
HT6154 Issues downloading photos with version 7.1
since i updated to 7.1 on my iphone 5 I can't download photos anymore. when i hit trust after connecting it appears to disconnect the phone instead of making photos available for download.