Unable to load network list, unable to load network list

after Iphone went inyo shop for unlock sim pin, (the kids played with it) it seemed to work
but home found out trhat there is no signal showing
it gives message unable to load network list

Hi there,
I had kind of the same thing where i would arrive abroad or back in the UK after being abroad and my iPhone would take 20-30 minutes to get a signal and when loading up network selection would always get unable to display message.
Had phone replaced by apple and the issue hasnt occured in the once ive been abroad since - connected pretty much straight away.
Just wondering if you are having the issue of delayed text messages where people text you and sometimes it takes 30mins-few hours to get delivered to your phone. Or the issue of people sometimes call you and you good signal and it goes straight to voicemail??

Similar Messages

Connected to an active network but unable to load web pages

Hi,
I am using an old Powerbook with OS 10.2.x and am trying to add it to an existing network at home. The network is a DSL/ADSL connection, which is received by a modem and is passed on to a wired/wireless router. I have a PC which connects successfully to the router either by wire or wireless and is able to load web pages.
My Mac, however, does not. It indicates that it is connected to my wireless network, and shows full signal strength. It is assigned an appropriate IP address by the router. However, I cannot load any webpages. All I get is a 'server not found'. This is vexing me, and I have been at it for hours, but no solution.
Let me add that with the same settings, I was able to browse on my Mac also yesterday, but for some reason, I have no luck today. Can someone please indicate what is going on?

I am having the exact same problems. My laptop (Gateway) connects fine to the router, but my Mac does not. They sit right next to each other upstairs. The signal will SOMETIMES come through to my Airport card and when it does it is at full strength, but when i run Safari, nothing. I have tried to enter all the information that my PC has printed out and displayed for me, but i have no clue what half of the things are. and my applecare has expired so the people at Apple will not help which is extremely annoying. Sorry i can't help. But if i find anything i will let you know.

When I want to get on my wifi I tap my wifi in settings but it just loads and says unable to connect. It wont let me sign in. All my family's apple products are working. Why is this happening?

When I want to get on my wifi I tap my wifi in settings but it just loads and says unable to connect. It wont let me sign in. All my family's apple products are working. Why is this happening?

Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

I get error message when I try to load lightroom 5 -unable to laod application correctly (oxooooo7b)

I get error message when I try to load lightroom 5 -unable to laod application correctly (oxooooo7b)
what can I do

Search here or Google ... https://helpx.adobe.com/lightroom/kb/error-unable-start-correctly-0xc00007b.html

Loading module "oracleasm": Unable to load module "oracleasm"

Hi,
I'm trying to install ASM Library RPMs.But the oracleasm configure is failing with the following error:
Default user to own the driver interface [507]:
Default group to own the driver interface [507]:
Start Oracle ASM library driver on boot (y/n) [y]:
Fix permissions of Oracle ASM disks on boot (y/n) [y]:
Writing Oracle ASM library driver configuration: [ OK ]
Loading module "oracleasm": Unable to load module "oracleasm"
[FAILED]
the following are the RPM version details:
[root@narya tmp]# ls oracleasm-2.6.9-5.0.5.EL*
oracleasm-2.6.9-5.0.5.ELsmp-2.0.0-1.i686.rpm
[root@narya tmp]# ls
oracleasmlib-2.0.2-1.i386.rpm
oracleasm-support-2.0.3-1.i386.rpm
the following are the kernel version details for my machine:
[root@narya tmp]# uname -r
2.6.9-5.0.5.EL_snaresmp
Please do let me know if i'm installing the right RPMs and if not please provide me the link for the right RPMs.
Thanks in advance!!!

Are you running this on RHEL4?
If so, this error could be caused by SELinux. If SELinux is enabled, it can prevent the successful load of the ASMLIB driver. This is documented in Bug 4758215.
If you see an error message similar to the following in your /var/log/messages file:
modprobe: FATAL: Error inserting oracleasm: Permission Denied
then it is likely that SELinux is enabled and this is preventing the module from being loaded.
The solution suggested by Oracle is to either disable SELinux or upgrade to RHEL 4 Update 3 as a fix for this bug is incorporated into this release.

We were unable to open your mailbox. Try loading a...

I am unable to log in to my Ovi Mail account, and am receiving an error message; specifically:
'We were unable to open your mailbox. Try loading again.'
I preferred the Ovi Mail service when it was still inhouse at Nokia. Yahoo doesn't even appear to keep an SSL connection beyond initial authentication.
Can anyone advise on how to resolve this issue?
Solved!
Go to Solution.

Getting the same message this morning...
First thing I logged in to check my emails and all was fine - then I sent an image from my phone (E72) via email to myself, and now I can't access my email via the PC...
Is this an issue with Nokia/Ovi as a whole today (I've seen several of the same messages today from different people), or is it something I've done by trying to email from my phone to my PC? (my data cable's not working!)
Cheers...

After applying BM3.8.5_ir1: "IKESetupSocket: Unable to bind socket!", IKE not loading

Hello,
I just applied the Interim Release 1 BM3.8.5 and rebootet the server after at
least several months of uptime when the patch files were applied - so it might be
related to 385_ir1; Or something went wrong during the last months of uptime that
way; that a reboot just caused the trouble to be revealed.
Well, on the next reboot after applying BM3.8.5_ir1 I got this on the IKE screen:
-------------------------- IKE SCREEN ----------------------------------
3-19-2008 12:53:41 pm IKESetupSocket: Unable to bind socket!
[snip empty lines]
<Press any key to close screen>
-------------------------- IKE SCREEN ----------------------------------
At this state these TCP NLMs were loaded:
TCP.NLM
Loaded from [SYS:SYSTEM\] on Mar 19, 2008 12:35:40 pm
(Address Space = OS)
Novell TCP/IP Stack - Transport module (Domestic)
Version 6.91.05 October 25, 2007
Copyright 1994-2007 Novell, Inc. All rights reserved. Patent pending.
TCPIP.NLM
Loaded from [SYS:SYSTEM\] on Mar 19, 2008 12:35:40 pm
(Address Space = OS)
Novell TCP/IP/IPSec Module (Domestic) NICI Enabled
Version 6.91.10 October 25, 2007
Copyright 1994-2007 Novell, Inc. All rights reserved
Patent pending Portions Copyright 1986-1995, RSA Data Security, Inc.
BSDSOCK.NLM
Loaded from [SYS:SYSTEM\] on Mar 19, 2008 12:35:40 pm
(Address Space = OS)
Novell BSDSOCK Module (Domestic)
Version 6.91.04 October 25, 2007
Copyright 1994-2007 Novell, Inc. All rights reserved.
As it's a socket error I thought that applying the latest TCP patch might help
out:
TCP681K, another reboot, but no change at all.
As IKE isn't loading server side all VNP functions are not operational.
PKIDIAG is without errors, if these certificates should interact with IKE as well
(I honestly have to state, that I don't know, if or if not these Certs interact
with IKE ...)
Anybody a quick solution? Otherwise I'll try to backrev to BM3.8.5 and the prior
TCP version.
Thanks for any input.
Regards, Rudi.
IT-Beratung Rudolf Thilo
Schweinfurter Str. 131
97464 Niederwerrn
t: +49 (0)9721/6464840
f: +49 (0)9721/6464841
m: +49(0)171/685 9 685

Hello,
after investigating in a totally wrong direction for many hours <doh!> I finally
back-rev.ed the lib files from c:\nwserver\!backup.lib and
sys:system\!backup.lib, after that was done the IKE had no trouble any more.
In the load sequence of the server's reboot NMAS had a load error that pointed in
that direction... (several DS*.NLMs in the LIB patch files)
I have a looger screen save file of both, a "trouble boot" and a clean boot after
removing the patch files. What I missed was to draw a config.txt of the trouble
state. :(
Quite interesting is the fact, that after may be 30 - 60 Minuntes of uptime the
BM had difficulties to access the C: drive:
----------------------------Logger Screen ------------------------------------
NetWare Configuration File Transfer Cache to DOS Error: 0x4
Registry rolling back to last known good registry file.
----------------------------Logger Screen ------------------------------------
Then no NLMs could be loaded any more at all: Neither DOS side, nor sys:system or
from anywhere else. Funny fact: With the already loaded toolbox a "DIR" was
presenting everything absolutely normal, DOS and SYS: side....
Well, the NBM-Rule-Container is restored now from tape, the filters.txt is as it
was before (seveal reboots) and with my 2nd. BM install I was painfully
remembered that there can be just one BM per container <grrr> ;) (nice design...)
Patches applied when the trouble showed up
NW6.5SP6
BM3.8SP5
plus the hotfixes available till Dec 2007
Finally I applied these (many hours ago >-O~ )
LIBCSP6B
NWLIB6K
WSOCK6N
TCP681K
BM3.8.5_ir1
.... in the timed order they were given to the public (I didn't check right now,
the order above isn't necessarily the right order I used.)
If someone should be interested in the logger.txt of both states, they are too
large for *one* posting here, drop me an email.
Regards, Rudi.
IKESetupSocket: Unable to bind socket!
IKE not loading any more
NMAS error in boot sequence
Error accessing registry files,
NLM load from all search paths impossible
IT-Beratung Rudolf Thilo
Schweinfurter Str. 131
97464 Niederwerrn
t: +49 (0)9721/6464840
f: +49 (0)9721/6464841
m: +49(0)171/685 9 685

'Cannot begin data load. Analytic Server Error(1042006): Network Error

Hi...
I got a error message when I upload data from source file into Planning via IKM SQL to Essbase (data).
Some records are found following errors.
'Cannot begin data load. Analytic Server Error(1042006): Network Error [10061]: Unable To Connect To [localhost:32774]. The client timed out waiting to connect to the Essbase Agent using TCP/IP. Check your network connections. Also please make sure that Server and Port values are correct'
What is this error about? is the commit interval too large? now the value is 1000.

Hi,
You could try the following
1. From the Start menu, click Run.
2. Type regedit and then click OK.
3. In the Registry Editor window, click the following directory:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Tcpip\Parameters
4. From the Edit menu, click New, DWORD Value.
The new value appears in the list of parameters.
5. Type MaxUserPort and then press Enter.
Double-click MaxUserPort.
6. In the Edit DWORD Value window, do the following:
* Click Decimal.
* Enter 65534.
* Click OK.
7. From the Edit menu, click New, DWORD Value.
The new value appears in the list of parameters.
8. Type TcpTimedWaitDelay and then press Enter.
9. Double-click TcpTimedWaitDelay.
10. In the Edit DWORD Value window, do the following:
* Click Decimal.
* Type 300
* Click OK.
11. Close the Registry Editor window.
12. Reboot essbase server
Let us know how it goes.
Cheers
John
http://john-goodwin.blogspot.com/

[SOLVED] Network Configuration -- unable to start a service file

I am following this wiki page (Using Static IP address step) and created /etc/systemd/system/network.service as instructed
[Unit]
Description=Connect to the other pc
Wants=network.target
Before=network.target
BindsTo=sys-subsystem-net-devices-lan.device
After=sys-subsystem-net-devices-lan.device
[Service]
Type=oneshot
RemainAfterExit=yes
EnvironmentFile=/etc/conf.d/network
ExecStart=/sbin/ip link set dev lan up
ExecStart=/sbin/ip addr add 192.168.1.2/24 dev lan
ExecStart=/sbin/ip route add default via 192.168.1.1
ExecStop=/sbin/ip addr flush dev lan
ExecStop=/sbin/ip link set dev lan down
[Install]
WantedBy=multi-user.target
But I am unable to start network.service
$ sudo systemctl start network
Job for network.service failed. See 'systemctl status network.service' and 'journalctl -xn' for details.
$ systemctl status network.service
network.service - Connect to voice
Loaded: loaded (/etc/systemd/system/network.service; enabled)
Active: failed (Result: resources)
$ sudo journalctl -xn
-- Logs begin at Sat 2013-03-30 03:48:02 AMT, end at Thu 2013-04-04 18:17:46 AMT. --
Apr 04 18:17:26 work sudo[24774]: pam_unix(sudo:session): session closed for user root
Apr 04 18:17:44 work sudo[25354]: void : TTY=pts/0 ; PWD=/etc/systemd/system ; USER=root ; COMMAND=/usr/bin/systemctl start network
Apr 04 18:17:44 work sudo[25354]: pam_unix(sudo:session): session opened for user root by void(uid=0)
Apr 04 18:17:44 work systemd[1]: Starting Connect to the other pc...
-- Subject: Unit network.service has begun with start-up
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Documentation: http://www.freedesktop.org/wiki/Software/systemd/catalog/7d4958e842da4a758f6c1cdc7b36dcc5
-- Unit network.service has begun starting up.
Apr 04 18:17:44 work systemd[1]: Failed to load environment files: No such file or directory
Apr 04 18:17:44 work systemd[1]: network.service failed to run 'start' task: No such file or directory
Apr 04 18:17:44 work systemd[1]: Failed to start Connect to the other pc.
-- Subject: Unit network.service has failed
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Documentation: http://www.freedesktop.org/wiki/Software/systemd/catalog/be02cf6855d2428ba40df7e9d022f03d
-- Unit network.service has failed.
-- The result is failed.
Apr 04 18:17:44 work sudo[25354]: pam_unix(sudo:session): session closed for user root
Apr 04 18:17:46 work sudo[25421]: void : TTY=pts/0 ; PWD=/etc/systemd/system ; USER=root ; COMMAND=/usr/bin/journalctl -xn
Apr 04 18:17:46 work sudo[25421]: pam_unix(sudo:session): session opened for user root by void(uid=0)
Additional info:
I have connected 2 PCs with LAN (Ethernet) cable and want configure them for exchanging files. Both running Arch Linux. I am following the Network Configuration wiki page from the beginning. Didn't have luck with DHCP/dynamic IP, so trying Static IP this time. Restarting the pc with network.service enabled results in same error (in systemctl --failed). Same error message on both PCs.
Trying to run ExecStart lines one by one:
$ sudo /sbin/ip link set dev lan up
$ sudo /sbin/ip addr add 192.168.1.2/24 dev lan
RTNETLINK answers: File exists
$ sudo /sbin/ip route add default via 192.168.1.1
RTNETLINK answers: File exists
Does this mean there already is IP address and route assigned? If so, how to find out which service has done that? Do I need to remove it? Am I following the right wiki page (didn't find another)?
What am I doing wrong and how can I correct this error? / Point me in right direction.
Last edited by axper (2013-04-04 19:26:17)

henk wrote:
EnvironmentFile=/etc/conf.d/network
Apr 04 18:17:44 work systemd[1]: Failed to load environment files: No such file or directory
have you checked if the network file exists?
Oh thanks, that line was causing problems! Now I do have network.service(s) running on both PC's with this content:
[Unit]
Description=Connect to my desktop/laptop
Wants=network.target
Before=network.target
BindsTo=sys-subsystem-net-devices-lan.device
After=sys-subsystem-net-devices-lan.device
[Service]
Type=oneshot
RemainAfterExit=yes
ExecStart=/sbin/ip link set dev lan up
ExecStart=/sbin/ip addr add 192.168.1.2/24 dev lan
ExecStart=/sbin/ip route add default via 192.168.1.1
ExecStop=/sbin/ip addr flush dev lan
ExecStop=/sbin/ip link set dev lan down
[Install]
WantedBy=multi-user.target
I don't get any errors, and this is network's status (on both PCs) when cable is connected
$ sudo systemctl restart network
$ systemctl status network
network.service - Connect to my desktop
Loaded: loaded (/etc/systemd/system/network.service; disabled)
Active: active (exited) since Thu 2013-04-04 22:43:22 AMT; 8s ago
Process: 9761 ExecStop=/sbin/ip link set dev lan down (code=exited, status=0/SUCCESS)
Process: 9757 ExecStop=/sbin/ip addr flush dev lan (code=exited, status=0/SUCCESS)
Process: 9768 ExecStart=/sbin/ip route add default via 192.168.1.1 (code=exited, status=0/SUCCESS)
Process: 9766 ExecStart=/sbin/ip addr add 192.168.1.2/24 dev lan (code=exited, status=0/SUCCESS)
Process: 9764 ExecStart=/sbin/ip link set dev lan up (code=exited, status=0/SUCCESS)
And here wiki page is no more help. How can I test connection?
I try to ping, and it works on both machines (if it's the right thing to test?)
$ ping -c3 192.168.1.2
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
64 bytes from 192.168.1.2: icmp_seq=1 ttl=64 time=0.039 ms
64 bytes from 192.168.1.2: icmp_seq=2 ttl=64 time=0.050 ms
64 bytes from 192.168.1.2: icmp_seq=3 ttl=64 time=0.060 ms
--- 192.168.1.2 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 1998ms
rtt min/avg/max/mdev = 0.039/0.049/0.060/0.011 ms
Now I need to figure out how to share files. Thanks all.
Last edited by axper (2013-04-04 19:04:43)

Tecra A10 - Refurbished - unable to get it connected to my home network

I just got this Tecra A10-104 refurbished Laptop...before I take it back I am asking here just in case theres something I have missed as I am unable to get it connected to my home network.
I am running a Belkin Wireless Router that has 2 main PC's directly connected (LAN), and another PC wirelessly connected.
This is my router: http://www.belkin.com/uk/support/article/?lid=enu&pid=F5D8233uk4&aid=9238&scid=0
All PC's working fine and connected.
Now I'm trying to setup this laptop to connect.
I uninstalled the Vista Business and ussed the XP Pro Product Recovery disc that came with the Tecra.
My WiFi card is: Intel(R) Wireless WiFi Link 5100 (Driver Date: 27/04/2008 - Driver Version: 12.0.0.73)
It sees the network but no matter what i try just won't connect.
What I have done so far (read before suggesting stuff I have already tried):
Reconfigured routers WPS to Shared Key system.
Made sure the wireless adapter has settings set to 20/40hz (auto)
Restarted router, cable modem & laptop several times
Wireless button on side of Laptop is ON.
FN + F8 to enable WIFI (ON) BLUETOOTH (OFF)
Added wireless network to Auto Connect settings along with SSID and passcode end encryption method.
Clicked connect when network appears in network viewer dialogue and retyped passcode.
Not working.
I should add the Laptop has no problems connecting via its Gigabit LAN port.
Anything else I'm missing?
Thanks in advance.
EDIT: Dual post removed.

UPDATE:
The next thing I tried was to reinstall Vista Business from recovery disc to see if this suffered from the same problem.
The wireless connection worked fine on Vista and, despite the updates that I was being offered, worked without needing to update any drivers.
This made me think...so the issue is probably XP DRIVER related.
What I have done now is backup all the driver updates I was told to download by TEMPRO (BIOS & wireless manager updates included).
I think part of the problem is that TEMPRO only works in Vista (not XP) so you are not informed of any updates that may be required if you downgrade to XP straight after purchase (which is what I did).

I am unable to sign in to my wi fi network on my ipod because the keyboard wont come up. what do i do?

i am unable to sign in to my wi fi network on my ipod because the keyboard wont come up. what do i do? please help me out

First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."

Unable to get LaserJet M175nw to print over network

I have just installed a new LaserJet 100 Pro M175nw printer on my network. However I am unable to get it to print via the network.
The printer is connected to a ethernet cable and configured with a static IP address on the network
I am using a Windows 7 computer for printing
All internal functions of the printer work correctly e.g. copy, reports
Printing works when connected via USB to a computer
When using the printer via the network:
Scanning works correctly
The embedded web mangement page for the printer works correctly
The HP Print & Scan Doctor diagnostics give the configuration all green ticks
Print jobs stay in the print queue until they change to an error status.
The printer does not seem to recognise the print job at all - no progress message indicating printing document on the console
If the printer is in sleep mode it does not wake up
Test print pages from the HP Installer, from the Windows Printer Property dialog, from Acrobat Reader and from MS Word all fail.
All symptoms remain the same when I turn off the Windows Firewall
Another HP LaserJet 2605dn printer on the network prints correctly on a different IP address but also using the RAW format on port 9100.
I have removed all drivers for other HP printers in case there was a conflict - no change after re-installing the software.
Can anyone suggest what I might have overlooked? Thanks for your help.
This question was solved.
View Solution.

I am confused by your last statement, a TCP/IP is a network connection, which is why the universal print driver is suggested.
From what you have described, there is an issue with the print queue. Try running the Print and Scan Doctor :
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c03286146
Also, I am not sure if you tried the PCL6 driver or not, but I would like you to at least try it so that I know what its behavior is.
Let me know how that goes and I will get right back with you!
-Spencer

Unable to print to USB printer over the network

Hi all,
I have an iMac and an Macbook Air, both running 10.6.4, and I've got an HP LaserJet 1200 printer connected to the iMac by USB. Both machines are on my home wireless network (Linksys, FWIW).
I seem to be unable to print to the LaserJet over the network from my Air. I've tried all manner of permutations of printer setup on the Air: IPP/LPD/HP JetDirect; entering the hostname (*.local) and the IP address of the host; leaving the queue blank and not; and leaving "Print Using" as generic vs selecting the LaserJet drivers. The printers appear in the "Default" Add Printer menu as Bonjour Shared, but this doesn't seem to work either.
Following other threads, I've tooled around with CUPS (resetting the configuration file, etc.), with no success. The other threads I've found on the subject seem to be more specifically addressed to folks trying to use an AirPort.
Any suggestions for what to try next?

In that case, let me elaborate on what happens when I try to set up the printer via Bonjour, in case there are any clues in the behavior that I'm seeing. The printer seems to appear twice in the "Default" pane, with Kind as 'Bonjour Shared' and Printer Names as follows:
HP LaserJet 1200 @ (hostname)
HP LaserJet 1200 @ (hostname) @ (hostname)
Selecting the first, it displays "Gathering printer information..." for a few minutes, then strikes out, suggesting Generic PostScript Printer rather than the correct driver. Whether I stick with that or select the correct driver manually and then try to print, it hangs on 'Copying print data..." (in the print queue).
Selecting the second, it gathers printer information only for a second or two before settling on Generic PostScript Printer. If I stick with Generic PostScript Printer, it hangs on 'Connected to printer...' but if I select the correct driver, it hangs on 'Copying print data...' again.

%APF-4-CREATE_PMK_CACHE_FAILED: apf_pmkcache.c:561 Attempt to insert PMK to the key cache failed. unable to insert a new entry in PMK cache list.Length: 32. Station:

I received this error using apple IPAD version 7.1.2 connecting to cisco WiSM controller version 7.0.250. access point wireless setup using local-hreap.
below are the syslog messages.
: *mmListen: Aug 25 10:38:35.962: %APF-4-CREATE_PMK_CACHE_FAILED: apf_pmkcache.c:561 Attempt to insert PMK to the key cache failed. unable to insert a new entry in PMK cache list.Length: 32. Station:98:fe:94:90:70:ef
: *mmListen: Aug 25 10:38:35.962: %MM-4-PMKCACHE_ADD_FAILED: mm_listen.c:6479 Failed to create PMK/CCKM cache entry for station 98:fe:94:90:70:ef with update from controller
: *dot1xMsgTask: Aug 25 12:09:27.883: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:3092 Max EAP identity request retries (3) exceeded for client 98:fe:94:90:70:ef
: *dot1xMsgTask: Aug 25 12:57:32.503: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:3092 Max EAP identity request retries (3) exceeded for client 98:fe:94:90:70:ef

Hi Ravi Rai,
I'm sorry to hear about the issue you are having with your Mac. If you are having hard freezes or restart issue that don't appear to be drive related, even after reinstalling Mavericks, you may want to try the troubleshooting steps outlined in the following article:
OS X: When your computer spontaneously restarts or displays "Your computer restarted because of a problem."
Regards,
- Brenden

I am unable to add to my bookmarks and my reading list on my iPhone.

I am unable to add to my bookmarks and my reading list on my iPhone 4S. I was able to perform these two functions yesterday. In addition my bookmarks have been deleted. Any help would be greatly appreciated.
Thanks in advance

Make a master list, preferably on iCloud.
You should be able to move contacts around via iTunes.
Just drop the vCards into the Address Book and wait for the sync to finish.

Unable to set the ip address for hosted network client after creating WIFI hotspot

Original Title: INTERNET CONNECTIVITY PROBLEM WITH MY LAPTOP WIFI HOTSPOT
HI all
I am able to use internet connection from my lap hotspot, when the internet source is Public or private wifi.
so I know the cmd window commands for hotspot and settings of client(sharing to hosted network client, assigning IP address etc.,)
but the problem I am facing is slight different
I am using my cdma wireless broadband datacard as my source internet connection(Reliance netconnect +)
when I try to create hotspot for this, as usual I am able to create the hotspot and able to share the internet to hostednework client.
but I am unable to set the ip address for hosted network client, if I try to set ip 192.169.137.1 and 255.255.255.0
as soon as I close the window, the ip address also disappears
when connect my android phone to that hotspot, it is able to connect but there is no internet connectivity.
when I check the hostednetwork client for packet transmission, both sent and received packet is happening., I mean transmitting
so what cause the failure in internet connectivity but success in hotspot connectivity?
check the screen shots...
can u help me..
its little complicated

Hi,
Please make sure the Ad hoc connection IP adress is at the same range with your local connection. In addition, how about recreate the ad hoc connection for test, please have a try.
If problem persists, please use Network troubleshooter in Action Center to fix this problem for test.
Roger Lu
TechNet Community Support

Unable to load network list, unable to load network list

Similar Messages

Maybe you are looking for